Search Documents

By Jerome C. Motz

Primary Crushers The types, sizes and number of crushers employed in a complete reduction system will vary with such factors as the volume of ore to be processed, the size of the mine-run lump material, the hardness of the ore bearing rock and the size and dimension required for the final product. Basically, for primary crushing there are only three distinct types of crushing equipment. These are the Jaw crushers, Gyratory crushers and Impact crushers, and they each have their own distinctive operating characteristics. Jaw crushers operate by squeezing the rock between the fixed and the movable sides of a tapered cavity. Variations of pitch and swing have been tried, but most Blake-type machines have a crushing angle of about 27° between swing and stationary jaws. The principle of which Gyratory crushers work is very simple. If a Cone is mounted on the upper end of a vertical shaft and the top of the shaft is held .stationary while the lower end is rotated eccentrically, the Cone will also swing eccentrically. If the Cone is enclosed in a suitable housing, it will swing toward and away from the housing walls-as it rotates. If the done and the housing walls are sufficiently strong and heavy, anything caught between them will be crushed.

Jan 1, 1978

By H. S. Hanna, C. Rampacek

The problems and limitations encountered in the Physical beneficiation of the Appalachian Red Iron Ores are discussed. Two major problems are identified - the high phosphorus content and the fine dissemination or encapsulation of mineral impurities in the iron-bearing minerals. A process that combined extreme fine grinding techniques with magnetizing roasting or flotation-separation methods is suggested. By these methods, concentrates assaying 60-61 % Fe, exceeding the widely accepted upper limit of 56% Fe set for these ores, were produced with 75-90% iron recovery. Moreover, it was shown that the phosphorus content of these concentrates could be reduced from 0.25% to 0.03% phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1983

By Noel W. Kirshenbaum, George A. Pouska, James M. Link

Literally millions of words have been written on the subject of mineral slurry pipelining. The sheer bulk of literature on the subject should be enough to convince the interested observer that the method is both viable and widely applied. It is the intent of this paper to examine typical mineral slurry applications. This examination should reveal the reasons that the slurry system was selected over other transport modes and it should provide a framework for determining the applicability of the technique to new projects. Slurry transport involves the conveyance of solid particles by suspension in a moving liquid. Almost any combination of solids in liquids may be imagined, and the conduit may be an open channel or a closed pipe. Historically, the most numerous slurry transport applications consisted of mineral particles in water. However, current research investigations are emphasizing other liquid carriers, specifically those which have greater economic value. Among these are gaseous and liquid fuels and chemical feedstocks. Another area being investigated involves the use of the pipeline as a chemical reactor system. The long residence time and turbulent flow characteristics of the pipeline make it particularly attractive for certain chemical reactions. Because these new systems involve a valuable liquid as well as a valuable solid, there is increased attention to solid-liquid

Jan 1, 1980

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

By Don Blackmar

THE production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically every type of manufacturing concern.. Its business is unique in that it generally buys from its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of many of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the magnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and-steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a 'general way, attempting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturers reclaim' their own metallic wastes.

Jan 1, 1928

Until the end of 1960, the small primary aluminum industry in Australia was run by the government. The entire operation was at Bell Bay on the north coast of Tasmania. It consisted of an alumina plant and smelter, owned jointly by the Commonwealth and the State of Tasmania. Apparent domestic demand that year was about 48,000 long tons; 11% thousand came from Bell Bay; the rest was imported. By March 1964, Australia had two fully integrated aluminum companies. The government has stepped out of the picture and the key word of the industry from bauxite to metal is "growth." Present annual capacity of the two companies for making aluminum metal totals 92,000 long tons a year. Australian demand is about 60,000 tons. By 1968 Australian consumption should be 90,000 tons and by 1970 it is expected to reach 107,000 long tons per year. Export markets for bauxite, alumina and metal are developing.

Jan 10, 1964

By Charles M. Rolker

THIS remarkable and well-known district lies about 320 miles south of Salt Lake City, in Washington County, near the Arizona border of the territory. It is now reached by the Utah Southern Railroad and its extension, and the last 100 miles are run by stages. These vehicles are called "jerkies" in the West, which name conveys a good idea of the comfort they afford, and the relief experienced when you alight. Arriving at Silver Reef, the main camp of the district, one sees at once that he stands where once a surging sea had its domain, marked now by heavy sandstone deposits of a red and white color. The town itself, a neat, clean, and orderly mining town, is encircled on the north by traohyte and granite mountains, skirting to the west. They are cut through in places by deep gorges, left us as the only trace of the force of former currents, which drained the adjoining territory to the north; and which when swelled and infuriated by tempests and cloud-bursts, took in their grasp the huge blocks of

Jan 1, 1881

By James L. Sweeney

The Project Independence Evaluation System (PIES) is a complex evaluation, forecasting, and analysis system which represents the U.S. energy production, conversion, transportation and consumption activities. The system includes various models: An econometrically estimated energy demand model, used to evaluate the final demand functions for energy commodities ; A collection of supply models, used to evaluate the cost curves or supply curves for domestic crude oil, natural gas, coal ; An integrating model used to describe energy conversion and transportation activities and to calculate prices which equate energy supply and demand in each market. PIES has been used to generate conditional forecasts of the 1980, 1985, and 1990 states of the energy system--forecasts conditional upon the world oil prices, the energy policy environment, and other uncertainties. Scenarios have been structured to separately examine conservation initiatives, domestic energy supply enhancements, an extensive electrification strategy, and oil and natural gas well -head price regulation. This paper presents the basic model, discusses its use for examining policy options, and describes several forecast results. The paper draws heavily upon work completed for the 1976 National Energy Outlook, published by the Federal Energy Administration.

Jan 1, 1977

By T. T. Read

In discussing the taxation of mining enterprises, it is desirable to place limits of both time and space on the field of discussion. For our present purposes it seems best to limit consideration to taxation of mining enterprises in the United States, and to further limit the subject to taxation under approximately current conditions. Even with such limitations the field is large enough, since in this country we have, in most regions, a number of taxing powers; so that state, county and village tax systems must ordinarily be considered, in addition to our national or federal taxes. Nor is it possible, in discussing United States mineral taxes of today, altogether to pass by similar taxation in earlier periods, or related systems in other countries. It is perhaps hardly necessary to remind you, at the outset, that each age in the history of the world displays its own system of public revenues, and that the taxation systems of today are everywhere different from those of older times. Theories as to taxation have varied according to the economic basis of the society in which they were formulated, and our ideas as to justice in taxation fluctuate with changes in social conditions. The word taxation is used in a fairly definite sense today, but you have only to glance into the history of taxation to find that the paragenesis of ore deposits is a fairly simple subject as compared to the paragenesis of taxation systems.

Jan 1, 1932

By Charles M. Rolker

THIS remarkable and well-known district lies about 320 miles south of Salt Lake City, in Washington County, near the Arizona border of the territory. It is now reached by the Utah Southern Railroad and its extension, and the last 100 miles are run by stages. These vehicles are called "jerkies" in the West, which name conveys a good idea of the comfort they afford, and the relief experienced when you alight. Arriving at Silver Reef, the main amp of the district, one sees at once that he stands where once a surging sen had its domain, marked now by heavy sandstone deposits of a red and white color. The town itself, a neat, clean, and orderly mining town, is encircled on the north by trachyte and granite mountains, skirting to the west. They are cut through in places by deep gorges, left US as the only brace of the force of former currents, which drained the adjoining territory to the north; and which when swelled and infuriated by tempests and cloud-bursts, took in their grasp the huge blocks of

Jan 1, 1881

By P. K. Kaiser, C. Mackay

A circular shaft with a diameter of 6m was excavated by the conventional drilling and blasting method to a depth of 235m through 60m of glacial till, 1 Om of water bearing basal sand, 1 1 Om of clay shale (Bearpaw Formation) and finally a strata of coal, mudstone, siltstone and sandstone (Oldman Formation). The lined shaft was instrumented at three levels by multipoint extensometers to determine the displacement field near the shaft bottom, embedment strain gauges to measure the strains in the liner and IRAD-stress change gauges to observe the radial and tangential stress changes in the rock mass. The data from these gauges were used to determine the in situ stress field. An attempt to measure in situ stresses by overcoring was also made at a higher elevation. The performance of the shaft and its support was then evaluated by use of the "Convergence-Confinement Method". For this purpose the measurements of stress changes and displacements were combined to determine by extrapolation the displacements ahead of the shaft and after the liner installation. The convergence curves calculated in this fashion were then used to evaluate the performance of the cast-in-place concrete liner and of an alternate shotcrete shaft support system.

Jan 1, 1983

By R. B. Sosman, J. C. Hostetter

We have shown in the preceding paper that practically all natural oxides of iron contain a determinable percentage of ferrous iron, and in many cases the percentage approaches that in magnetite itself. Some of these oxides are true homogeneous solid solutions. Others are not homogeneous, and can be separated magnetically into fractions. The nature and cause of this inhomogeneity in certain special cases form the subject of the present paper. Magnetic FRactionation of Oxides of Iron The magnetic fractionation of a sample of oxide can be conveniently carried out by powdering the material very fine, and exposing it at various distances from the poles of an electromagnet. The magnet that we used was specially designed1 to give a strong field together with a steep gradient outside of the poles. It is set in a frame, with the pole pieces directed downward. A glass plate can bc adjusted at various distances beneath the poles. If the fine iron oxide powder is placed just beneath the glass plate, successive portions of the powder are picked up by the magnetic attraction and are caught against the glass plate, the most magnetic portions being taken up at the greatest distance from the poles. Some natural oxides can thus be separated into several fractions of different magnetic susceptibilities. Among other natural iron oxides, we examined the powder obtained by crushing some crystals of hematite from Elba.2 We found that

Jan 1, 1918

By H. W. McCue

In 1945 the number of oil wells drilled was less than in 1944 but the number of gas wells was greater. The oil wells numbered 176, completed for an initial production of 25,214 bbl., an average of 143 bbl. per well as against a total in 1944 of 245 drilled for 32,886 bbl., or 134 bbl. per well. All of these wells were in proven areas and no new discoveries

Jan 1, 1946

By Guy Crane

I. INTRODUCTION THE geology of the Tintic mining district, fully treated, would occupy an elaborate monograph. This less comprehensive paper is devoted primarily to the occurrence and origin of the orebodies of the district, while space is given to those phases of the general geology only which seem necessary to a proper setting of such a discussion. The first geological report on the Tintic district to be issued was that by Tower and Smith, published in 1899, in the form of a paper in Part III of the Nineteenth Annual Report of the U. S. Geological Survey, and also as Folio No. 65, Geologic Atlas of the United States. About four years ago a second investigation was begun by Waldemar Lindgren and G. F. Loughlin, of the U. S. Geological Survey. With the exception of a paper on the oxidized zinc ores of the Tintic district by Mr. Loughlin, the results of their work are still unpublished. The writer's acquaintance with the district began in the fall, of 1913, and has extended over a period of about two years.

Jan 10, 1915

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system.

Jan 1, 1941

By Ionel Gardescu

IN connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,1 an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the dis-placement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S5, R4, the sand reservoir R, R1, R2, F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415 lb. per sq. in. with no free gas present. This was ascertained by. closing off all the outlet valves, and determining the coefficient of compressibility of the system by means of the dis-placement chamber D.

Jan 1, 1932

By Y. Fukunaka, Y. Kondo, Z. Asaki, S. Nakashita

The pyrite smelting process in which about half amount of sulfur is recovered from pyrite by thermal decomposition in an oxygen-free high-temperature combustion gas flow in the flash smelting furnace is being conducted at Kokkola Works in Finland. A mathematical model of this process was developed, and the rates of thermal decomposition and fusion of suspended sulfide particles in the reaction shaft of furnace was calculated. This model is thought to be appropriate because of a fairly good coincidence of the calculated length of reaction zone with the shaft height of the furnace at Kokkola Works. The calculated reaction zone in which the thermal decomposition and fusion of sulfide particles occur becomes longer when pyrite particles of larger sizes are fed. The feeding rate of pyrite particles and the gas velocity at the nozzle exit are also the important operating factors. These two factors are closely related to the volume fraction and the residence time of suspended particles in the gas stream, and the optimal combined levels of these factors at which the length of reaction zone becomes minimal were obtained.

Jan 1, 1976

By David Swan

No mystery shrouds the discovery of chromium. The indefatigable French chemist Vauquelin, in reporting his discovery of this chemical element to 1'Institut National in 1798, concluded his discourse with the statement: "I place before the eyes of the Institute a small quantity of chromium and several of its most re- markable combinations." Working with the so-called "red lead of Siberia, Vauquelin not only prepared numerous chemical compounds of the new metal, but he reduced the oxide to the metallic state. These chemical compounds possessed a variety of remarkably distinctive colors; so, acceding to suggestion, Vauquelin named the new element chrome (chromium), a derivative of the Greek word chroma, meaning color. Siberian "red lead" (crocoite) was not plentiful; however, it was not long before Vauquelin's prediction was realized that the chemical compounds of chromium would become useful in the arts when sources of chromium became more readily available. Although chrome-iron ore (chromite) became obtainable in France, the United States and elsewhere during the early part of the nineteenth century, it is interesting to note that from 1828 to about 1860, Maryland, Pennsylvania, and others of the eastern United States furnished almost the entire chrome-ore requirements of the world. Several countries each in turn have since dominated for certain periods the supply of chromite. In recent years, the largest tonnages have come

Jan 1, 1953

By W. A. Goodyear

It is safe to assert that in cities generally, the fuel of the future for all domestic, as well as for most manufacturing and metallurgical purposes, will be gaseous fuel. The immense advantages which gas possesses in facility and cheapness of distribution, cleanliness, and economy of manipulation, and the facilities which it offers for utilizing in almost all cases a much higher percentage of the total quantity of heat produced, than it is possible to do with any kind of solid fuel, are facts which will vastly more than compensate for the comparatively small loss of heating power, which will be found necessary in the turning of the solid fuel into gas upon a large scale, and which, in the bpinion of the writer, will, at no distant day, command attention, and will ultimately result in a revolution in our use of fuel. The employment of gaseous fuel upon a scale of any considerable magnitude, has hitherto been almost entirely confined to the utilization of the waste gases of the iron smelting furnace for heating the blast, and the rapidly increasing use, for certain metallurgical pur-

Jan 1, 1883

By A. C. Fieldner

A FORMER paper1 described in detail various methods of calculating coal analyses to obtain the composition and calorific value of the pure coal substance-that is, of the coal free from its mineral matter. The paper included a table showing calorific values of pure coal, as calculated from float-and-sink portions, by means of the Parr formula for "unit coal" and by the customary moisture-free and ash-free formula. A modification of the Parr formula was proposed, based on the assumption that one-half the sulfur present in coal occurs as pyritic sulfur and one-half as organic sulfur. In the published discussion of the paper Cady gave a table of results on a large number of Illinois coals as obtained by the Parr formula and the proposed modification thereof. The results obtained by Cady indicate that the Parr formula applies better to Illinois coals than does the modified formula proposed by Fieldner and Selvig. The present paper gives results obtained by applying the modified Parr formula to the analyses of the float-and-sink portions of the coals shown in the former paper, and results obtained by applying the Parr formula, the modified Parr formula, and the simple moisture-free and ash-free formula to various coals of the United States ranging in sulfur content from less than 1 per cent to more than 4 per cent sulfur. A graphic method of estimating the calorific value of pure coal and determin-ing the relation of the coal ash to the mineral matter of coal, as proposed by Stansfield and Sutherland,2 was applied to a number of coals, and the results are given herein.

Jan 1, 1932