Search Documents

By R. P. Brown

To gain some idea of the progress recently made in the measurement of high temperatures, we must review the temperature-measuring devices of the past. As far back as 1782, Wedgewood, a famous potter in England, attempted to measure his, kiln temperatures by means of clay trials, or test pieces, that indicated the expansion or contraction that occurred with certain changes in temperature. He also produced cones off clay, formed of various mixes, to form a whole series for the range of temperature met with, in firing clay products. These cones are still extensively used to measure kiln temperatures in the pottery industry. Cones are affected not only by time but by temperature and the rate, of firing, consequently, they are not an accurate measure of temperature. In addition it has been common practice for years to attempt to measure temperatures with fusible salts. Capsules of these are inserted in the furnace and indicate, by melting; when a certain temperature, has been attained. While' such salts cannot be considered a precision form of temperature-measuring device, they have proved reasonably accurate in checking temperature.

Jan 9, 1919

By Richard N. Hunt

Bingham has produced 6 per cent. of this country's copper. In total production, it ranks fourth among the copper camps of North America, the order being Butte, Michigan, Bisbee, and Bingham. In its annual production, it held that same rank until 1919, when its production was exceeded by the combined production of the Globe-Miami district of Arizona. Bingham has also been a lead camp of the first order. Utah ranks third among the lead-producing states, and its production comes largely from three camps which, in the order of their productivity, are: Bingham, Tintic, Park City. Bingham's silver production is important, but it does not rank high as a silver producer. Utah owes its rank as first among the silver-producing states to Tintic, a camp 40 miles due south of Bingham. The United States Mineral Resources reports a total production from Bingham for the period 1865-1920 having a gross value of $528,043,432. History of the Bingham District Bingham is on the eastern flank of the Oquirrh range 30 miles southwest of Salt Lake City, from which it can be reached in an hour by auto, or by the Denver & Rio Grande or the Bingham & Garfield railroads. The automobile route is a paved road across the floor of Great Salt Lake Valley, through farming country. The Bingham & Garfield railway leaves the level of Great Salt Lake at the northern end of the Oquirrh range, and in 20 miles it climbs 2100 ft., and deposits the traveler upon a shelf cut in the side of Bingham Canyon below most of the mines, which are farther up Bingham Canyon and its tributary Carr Fork. Below lies the town, a narrow ribbon running for a couple of miles along the bottom of a canyon 2000 ft. deep—an almost impossible site for a community numbering, in prosperous times, 5000 to 7000 inhabitants drawn from all quarters of the globe. Up the canyon and down, and beneath the steep slopes nearby, and beneath the town itself, are the mining operations of over half a century. During the past two decades one mine, the Utah Copper, has become so gigantic an operation as to dominate all other activity in the camp. It has become the greatest copper mine on the continent in production,

Jan 1, 1924

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years, the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture, and the ductility values can often be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel, Several types of abnormal loss of ductility can be distinguished, of which those caused by excessive amounts of inclusions of undesirable type and those caused by unsuitable grain size and ingot structure are well known. The particular type of abnormal lowered ductility currently under consideration may be distinguished by the fact that the low-temperature aging treatment necessary for its relief is insufficient to cause any visible change in the microstructure as ordinarily observed. As this aging will in fact eventually occur at room temperature, the phenomenon of present interest may be given the symptomatic definition, "Temporary Abnormal Low Ductility." Some hundreds of previous investigations, largely qualitative in nature, have established, beyond reasonable doubt, that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen-, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, The Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. The interest of this investigation thus extends to permanent abnormal losses of ductility, such as are caused by the inclusions which sometimes result from special deoxidizing practices and possibly from metallic nitrides, but as these can be distinguished from the temporary effect of hydrogen, they have been excluded from the work reported here except when they

Jan 1, 1948

By E. T. Turkdogan

In this theoretical paper, a transport-reaction mechanism is suggested for the enhancement of the rate of vaporization of metals, or other materials, brought about by the process of convection and condensation. Based on theoretical reasoning it is predicted that, when there is a temperature gradient surrounding the heated object, a slight increase in the rate of vaporization brought about by natural convection is enhanced further as a result of condensation of the vapor close to the surface of the object. In order to derive the effective vapor-concentration profile, consideration is given to the super saturation of the vapor necessary for the homogeneous nucleation of the condensed phase from the vapor. For the formulation of the rate equation based on this mechanism, adequate information should be available on the transport properties of gases and vapors at elevated temperatures and the method of calculating nucleation pressures of the vapor. The methods of deriving such data are discussed in the paper and a rate equation is calculated for the vaporization of iron in helium for various temperature gradients in the boundary layer. Considerations are also given to the effect of oxygen on rates of vaporization of metals under isother ma1 and nonisotherma1 conditions. THE study of the methods of enhancement or retardation of basically transport-controlled vaporization reactions is of theoretical interest with possible practical implications. There are several ways of bringing about such effects. For example, Turk-dogan, Grieveson, and Darken1 demonstrated that the rates of vaporization of metals under isothermal conditions were increased by several orders of magnitude, up to the maximum rate attainable in vacuo, by introducing some reacting gas into the inert atmosphere surrounding the metal. Such an effect is brought about by the interaction of the counter-diffusing reacting gas and metal vapor in close proximity of the metal-gas interface. Another case which is often experienced in practice is that of vaporization affected by natural convection. Although several theoretical and experimental studies of this problem have already been made, no detailed consideration has been given to the possible effects of condensation of the vapor in the boundary layer on vaporization rates, which constitutes the subject matter of this paper. BASIC CONCEPT OF ENHANCED DIFFUSION-LIMITED VAPORIZATION When a heated object, for example a metal sphere, is submerged in a fluid medium, heat is transferred from the surface of the object to its surroundings by four simultaneously occurring transfer processes: i) free-molecular conduction at the gas-solid interface over the distance equal to the mean free path of the gas, ii) conduction and convection through the fluid-dynamic boundary layer, iii) latent heat of mass transferred, and it!) radiation. The free-molecular conduction becomes pronounced only when the total pressure in the system is very low, e.g., below 1 mm Hg. Therefore, this term may be neglected for ordinary pressures. At low mass-transfer rates, due to vaporization of the object, the contribution of process iii) to the heat transfer can also be neglected. Finally, since the temperature profile is not affected by radiation, the latter need not be considered. The natural convection is brought about by gravitational body forces arising from a decrease in the

Jan 1, 1964

By Leo J. Vogel, E. D. Hummer

INTRODUCTION by E. D. HUMMER An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contributes to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and operating costs of the plant, but greatly affects the design of the refuse disposal system. The design of a mine and plant should include the location and the estimated capacity of the disposal areas for the life of the property or plant. Complete evaluation of the disposal system and an estimate of its annual cost of operation over the life of the property or plant should be incorporated in the plant and mine evaluation. Plant design should be as simple as possible, consistent with the efficient production of clean coal. Material transfer points, crushing, screening and pumping operations should be kept to a minimum to reduce degradation and the subsequent increased difficulty and cost of refuse removal. The maintenance of good process control by operating management will result in a minimum of misplaced material in both refuse and clean coal. Reduction of misplaced float material in the plant refuse is an important factor in preventing combustion in the refuse storage pile. THE REFUSE DISPOSAL AREA Combustion in refuse piles occurs when air enters the pile in sufficient quantity to support oxidation. At certain rates of air in-filtration, the heat produced by the oxidation process is not dissipated and temperature rises.

Jan 1, 1968

By George S. Rice

The increasing use of mechanization at the face of the workings in coal mining and the consequent necessity of special supports of the roof has led, in several countries, to considerable scientific investigation, including physical tests in mines as well as on specimens of roof rocks to obtain data on the behavior of the immediate roof strata and on the effect of its pressure on supports while the coal is being mined. The investigations discussed in this paper do not include studies of the ultimate effect of subsidence and movement of the roof rock over the mine excavation, upon higher strata and the surface, but are confined to the immediate underground effects in the workings. The more recent principal investigations which have been brought to the attention of the writer are as follows: Germany.—The trial of strip packing, the usual method employed in Great Britain in longwall workings, as compared with complete packing heretofore used in Germany and in France to minimize subsidence; the behavior and strength of metal props under load; the testing of the strength of coal measure rocks, in the laboratory of the Technical High School of Breslau; and an investigation, by a special commission, concerning "bumps" as a possible cause of instantaneous outbursts of gas in coal mines of Lower Silesia. France.—The cause of instantaneous outbursts of gas in the Gard mines and tests by the official French experimental organization of the "electrical resistivity" of coal as a possible means of detecting a condition preceding an instantaneous outburst. Great Britain.—The subsidence of the roof and rise of the floor preceding and during excavation of the coal, in longwall and in room-and-pillar or bord-and-pillar workings; the compression and lateral movement of the road packs in longwall back from the face; the extent of separation of the immediate roof layers from the higher strata following mining excavation;

Jan 1, 1932

By Fred D. Rosi

Introduction There is probably no field in which materials research has played a greater role than that of electronics. However, to trace present and future patterns of materials research in electronics is not an easy assignment, since this industry has a high degree of dynamism in its growth, and is busily engaged today in the scientific improbabilities of only recent yesterdays. On the other hand, this task seems especially appropriate since electronics is a truly frontier industry - one whose place in American industries has advanced from 50th prior to World War II to 6th in 1967, with sales of more than $22 billion. And this growth has been associated with the equally rapid progress of science and technology over the period - in particular with the emergence of materials science as a vital force in underscoring this progress. For several reasons this parallel growth is not too surprising. First, by its very definition electronics is a science that essentially deals with the nature, behavior, detection, generation, control and utilization of electrons in solids or at their surfaces. Second, in the electronics industry, systems are made of an integration of components, and these components with their interconnections are made of materials. Thus, the basic building blocks of systems are materials; and it has been largely the advances in materials research and technology that have led to new and improved devices and systems. It follows, therefore, that the broadening of the frontiers in electronics through the exploration of new territories is tantamount to scientific discovery and materials innovation to a degree found in no other major industrial activity. But to put this in the proper perspective of present and future materials trends, it would be appropriate first to survey historically the progress in electronics by pointing out major scientific discoveries and associated materials research patterns that have led directly to its tremendous growth. Then from this base we can consider recent trends in materials research that could form the basis for future progress in the electronics industry. In my review I shall examine the areas most familiar to me, so I must acknowledge at the outset that this survey is not all-inclusive.

Jan 1, 1971

By F. H. Parsons

At the time that converting or bessemerizing of copper matte first began to be practiced by the smelters in the copper industry, converters were lined by tamping the flux, usually siliceous ore, into the steel shell. About 1910, practice in several plants had demonstrated the superiority of a basic lining of nonfluxing material and the addition of flux through the mouth of the converter. Adoption of the new method by nearly the entire industry followed. Basic linings are made of refractory "magnesite" brick manufactured, usually, from imported dead-burned magnesite. Either the linings are laid up in the shell dry or the bricks arc bonded with some mortar dictated by the preference of the user. Foreign, usually Austrian, magnesite was the main source of supply for these bricks, although there were domestic sources, but it was not until costs began to rise a few years after the first use of basic linings that these domestic sources were investigated to any great extent. Exigencies created by the World War necessitated the use of the domestic magnesite during this period, but the brick manufacturers reverted to the use of the foreign product after the war, because the impurities therein made a brick with a better fire bond than the purer domestic magnesite. Therefore the domestic product became available at a favorable price for any metallurgical process that permitted its use. The United Verde converting practice using magnesite linings has resulted in a high consumption of magnesite because of the zinc content of the low-grade matte. It was realized that the cost of these linings represented a large portion of the cost of converting, and an investigation was started to find means by which these costs might be lowered. In the neighboring state of California rather pure magnesite was being mined and treated for the market. The product, however, was purposely made to simulate the dead-burned grain magnesite product from foreign sources by the addition of fluxing impurities before burning. It was learned that this dead-burned California grain magnesite could be laid down in Arizona at a price one-third that of the same tonnage of "magnesite" brick manufactured from foreign magnesite. It was also learned that at least one California producer was ready to supply the market with periclase, which was a grain magnesia produced by burning the

Jan 1, 1934

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today's quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By W. O. Philbrook

An engineering analysis indicates that the coke rate in present blast-furnace practice is set not by chemical or thermal needs but to give adequate charge permeability for economical driving rates. An equation showing interrelations among pressure drop, gas flow, and charge characteristics has been derived. Flooding conditions and the location of the fusion zone are discussed. Maximum ore size is probably limited by chemical re-ducibility rather than by heat transfer. THE intention of this paper is to show that the ].imitations on the production rate and coke requirement of the iron blast furnace are not primarily chemical or thermal in nature but are related to characteristics of the burden and operation that govern gas flow, heat transfer, and stock movement. A semiquantitative analysis will be developed in terms of standard engineering principles to give a useful picture of the relative importance of physical and mechanical factors in contrast with the chemical features of the process that are more commonly emphasized. Most of the details of calculation have been omitted in the interest of brevity and to avoid submerging the rnain points in a sea of arithmetic. Numerical values have been arrived at by objective methods from reported operating data or by reasonable estimates of material properties where exact data are lacking and then tested to see how well they fit practice, rather than by working backward to find what assumptions are needed to give the desired answers. The analysis is oversimplified in many ways because exact engineering relations have not yet been studied for bed distributions as complex as are known to exist in the blast-furnace stock column. One objective of this paper is to show that the blast furnace, in spite of its complexity, can be at- tacked by engineering methods in the hope that this viewpoint will stimulate the kind of research needed for a more exact treatment. The basic ideas and many of the conclusions presented are qualitatively well known. A careful literature survey to credit the source of all observations not original to the author would indeed be voluminous, and such has not been attempted. T. L. Joseph's Howe Memorial Lecture' gives an excellent background of what is known about the internal workings of a blast furnace. Other important reference works or sources of specific information will be noted. It is hoped that the present paper will contribute something new, in method of attack and interpretation, that will aid in a clearer understanding of how to operate the blast furnace to best advantage. Factors Limiting Production and Coke Rates The rate of combustion of coke in a blast furnace, as in any fuel bed, is exactly proportional to the rate at which air is supplied. It is axiomatic, then, that the production rate of a furnace is limited by the rate at which it will take wind, i.e., burn coke, and the amount of coke that must be burned at the tuyeres to make a ton of iron of suitable composition. These two possible limiting factors will be considered briefly in the order mentioned. One common restriction on wind rate is flue-dust production. Since the volume of top gas is nearly proportional to the blast volume (by a factor of about 1.35 on a dry basis), an increased wind rate causes a correspondingly increased linear velocity of top gas in the throat of the furnace. The higher

Jan 1, 1955

By S. Usui, I. Iwasaki

The adsorption mechanism of dodecylammonium acetate (DAA) on mercury in potassium fluoride solutions at natural, near neutral pH was investigated. Difler-ential capacity combined with electrocapillary measurements on a dropping mercury electrode were found to provide a sensitive and reliable approach. A shift in the electro capillary maximum (or the point-of-zero-charge) towards positive polarization of the surface due to the adsorption of amine indicated a specific affinity of dodecylammonium ion for mercury surfaces. The amine was shown to adsorb competitively with potassium ion on mercury. Through correlation of the adsorption density of the amine, calculated from the thermodynamic analyses of the electrocapillary curves, and of the diflerential capacity curves, the adsorbed state and the orientation of the amine at the interface were considered. The similarities and the differences in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide were evaluated. With the promise of flotation providing a cheap and large-scale process for the upgrading of low-grade ores and magnetic concentrates, the iron ore industry has made a sustained search over the years for a flotation reagent of general applicability and high selectivity. Having shelves full of commercial reagents already on hand and anticipating more, both the users and the suppliers are in need of an experimental approach sensitive enough to differentiate the individual characteristics in each group of reagents. Therefore, the adsorption behavior of various flotation reagents on mineral surfaces from aqueous solutions has been a subject of much investigation. The current view of adsorption based on the electrical double-layer theory is formulated on the assumption that certain ions in solution act as potential-determining ions. Their concentrations fix the potential drop across the double layer and their adsorptions govern the surface charge.' Two methods used to study the adsorption

Jan 1, 1971

By Charles E. Mann, Douglas J. Lootens, Rufino B. Bomasang

INTRODUCTION The economy of the Philippines, like that of many other developing nations, has been severely strained by the rapid escalation of imported crude oil prices over the past decade. In an effort to reduce its dependence on imported crude, significantly increased emphasis, both in the public and private sectors, is being placed on the rapid development of Philippine coal resources. This paper is designed to present an overview of the Philippine coal industry, its historical development, present status, and future potential. COAL RESOURCES AND RESERVES In 1977, a British consulting firm collated all available data on Philippine coal resources and estimated the total coals potential at about 0.9 to 1.4 billion metric tons (mt). In 1981, using more recent data the Philippine Bureau of Energy Development (BED) estimated the potential at 1.7 billion mt. The BED estimated the proven coal reserves at 257 million mt. These coal resources are scattered throughout the major islands comprising the Philippine archipelago. However, about 52 percent of the currently proven reserves are located in the tiny island of Semirara between the islands of Mindoro and Panay. About 25 percent is located in the Cagayan Valley in northeastern Luzon while 13 percent is located in Mindanao. The remaining 10 percent is scattered in the islands of Cebu, Samar, Mindoro, Negros, Polillo, Batan, and Catanduanes. The bulk of Philippine coal is sub-bituminous in rank. Some bituminous coal with coking properties has been reported in Malangas, Zamboanga del Sur in western Mindanao, and in Catanduanes, but the exact tonnages have not been accurately established. It is believed, however, to be at most 5 million tons. A little semi-anthracite coal exists in Malangas with the remaining unmined reserves estimated at a little more than one million tons. Table 1 shows the quality ranges of Philippine coal deposits.. Figure 1 shows the distribution of known Philippine coal resources PHILIPPINE COAL PRODUCTION In 1981, total coal production was 330,720 mt. Though modest by world standards, this was the highest production figure in Philippine coal mining history. This came from 25 mines, mainly small scale underground mines of capacities varying from 10 to 100 tons per day (tpd). The actual production capability was about 800,000 mt in 1981, but the producers had to scale down production to the level of local demand. Even then, some 50,000 tons of coal remained unused by year-end. The 1981 production came from the following areas: Cebu 224,751 mt (68%) Zamboanga del Sur 57,095 mt (17%) Semirara 13,222 mt (4%) Polillo 17,132 mt (5%) Cebu has always been the main source of Philippine coal production. Coal mining has been carried out in Cebu for the last 50 years, although it has been characterized by a very crude mining technology. Due to the limited size of coal deposits and complicated geology, however, Cebu's share of the total national production is expected to go down to only 10 percent by 1985. Except for Semirara's open-pit production, the balance of Philippine coal production comes from underground mines. These underground mines generally use room-and-pillar methods, except for those at Zamboanga del Sur and Polillo which use modified longwall methods patterned after those used in Taiwan. Due to the much higher mining recovery, most underground mines are now planning on switching to longwall. At Semirara, an open pit mine is now being developed for a one million ton per year capacity by 1984, and will then be the largest Philippine coal mine. While present earthmoving work is done with bulldozers, loaders, and trucks, the main coal extraction equipment will be bucket wheel excavators imported from Austria. PRESENT COAL UTILIZATION Existing coal production is sold mainly to coal- fired cement plants and power plants. The balance is sold to a sugar central, a coconut oil mill, a food processing plant, and two plants producing carbide and ferro-silicon alloys.

Jan 1, 1982

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method. CONSIDERING the subject alone, this paper would cover only a mechanical treatise of pillar roping. Because the St. Joseph Lead Co. originated the practice, it is proper to give a short introduction to the company. It is also proper to describe pillars and discuss their purpose to justify expending large sums of money to preserve them after the surrounding area has been thoroughly mined. Because the St. Joseph Lead Co. originated the practice of back pinning with wedge bolts, patch plates and channel irons, and the pouring of substitute pillars of concrete, these too, are mentioned. The Southeast Missouri Division of the St. Joseph Lead Co. is the largest lead producer in the United States. About 95 pct of the present producing mines are in St. Francois County, which begins 60 miles south of St. Louis. The entire lead ore production of this county, at the present time, is mined and milled by this company, treatment plant capacity being about 22,000 tons per day. This area is also the oldest, lead having been mined at Mine La Motte, in Madison County, in 1723. Estimated production of all the various companies that have mined here is about 7,000,000 short tons of pig lead. Method of Mining The lead occurs in the ore as galena. Galena is found either in the form of disseminated or solid streaks, of varying thickness. Ore stratum is the Bonne Terre dolomite, which is about 350 ft thick, but almost all the ore is in the lower 100 ft. Ore is mined by room and pillar method in open stopes. These stopes vary in height from 7 ft to 200 ft, depending on the thickness of the pay ore in that spot. Back, or roof, is supported entirely by pillars. In a majority of stopes, after the loose scales are mined down, the back has remained solid for many years (fig. 1). Under ideal conditions pillars are spaced to form an equilateral triangle and are as small and as far apart as the height of the stope and the character of the back will permit. They vary in diameter from 10 ft to 50 ft and are from 18 ft to 50 ft apart, measured from the outer edges. In general, the pillars are approximately 12 ft in diameter, and 25 ft apart. The spacing is very uncertain because of the vagaries of the ore trend, the desire to better support breaks in the back, and the attempt to spot out the thinner ore by not placing one in the core of the ore body. Use of Structural Steel Channels In stopes where the back is bad because the overlying formations are thin with wet, weak and shaly

Jan 1, 1951

By J. Bulina, J. T. Brown

SINCE the inception of vacuum cold-hearth arc melting of high-temperature alloys (about 4 years ago) it has been theoretically reasoned and qualitatively found that better mechanical properties are often obtained from alloys which have been melted by this practice. Mechanical properties are emphasized in this evaluation because of their importance in design. Vacuum-arc melting has an intrinsic advantage in that it creates an ingot grain structure which is easier to forge and thus leads to greater yields for the finished product. The greater yield naturally gives the process an economic basis when the cost per pound of alloy is rather high. However, the question stressed here is, does the process create an alloy with inherently better properties? There are several theoretical reasons for suspecting that it does. One is the vacuum refining which should permit lowering the content of harmful residuals with high vapor pressures. A second is the vacuum process which should preclude the formation of harmful distribution of oxides, nitrides, or carbo-nitrides, by keeping the amount of such constituents formed to a minimum. A third is the vacuum-arc cold-hearth method which prevents the possibility of pick-up of harmful elements from a refractory crucible since none is used. Fourth, the rapid solidification rate, induced by having a cold mold and only small amounts of molten metal at any one time, minimizes the segregation of elements like titanium, aluminum, and molybdenum from the top to the bottom of the ingot. This rapid solidification rate also decreases the tendency of the above elements to form undesirable phases by segregating locally. Another less frequently considered vacuum-arc melting advantage is the inherently finer-grained ingot structure which can be produced. Finer initial grain size leads to better forgeability, and means that after relatively small reductions to billets or final forged products a finer-grained material is obtained, which, by virtue of its finer grain size, would usually have greater stress-rupture ductility.

Jan 1, 1960

By K. D. McBean, W. H. Hannay, B. A. Stimmel

The electrolytic plant at Trail, B. C., was erected by the Consolidated Mining and Smelting Company of Canada, Ltd., for the treatment of zinc ores and concentrates, particularly those of the Sullivan mine at Kimberley, B. C. It began operations in 1916 at a rated capacity of 60 tons of cathodes per day, which has been steadily increased to the present production of 400 tons per day. The Sullivan has furnished the greater part of the zinc so far produced, although notable tonnages of customs zinc concentrates have been treated. The maximum yearly tonnage of customs concentrates, 25,000 tons, was treated in 1926. Practically no customs concentrates hale been treated since 1929. The total bar zinc production to the close of 1935 was 1,092,782 tons. The zinc mineral in the Sullivan ore is marmatite of somewhat variable composition, ranging between 6ZnS.FeS and 8 ZnS.FeS. Practically all the zinc ores tributary to this plant are marmatites; and the iron content of the zinc mineral varies considerably. The formation of zinc ferrite during roasting is now a matter of common knowledge, so the possible extraction from any zinc concentrate is largely a function of the iron content; the progress made in concentration is reflected directly in zinc-plant recovery. The Trail plant operafes on the low-acid system, as do all the other major plants on this continent at present operating, except the electrolytic plant of the Sullivan Mining Co. at Kellogg, Idaho. The new Magdeburg plant, in Germany, occupies an intermediate position between high and low acid. Plant operation at Trail will be treated in this paper under five main sections: roasting, leaching and purification, electrolysis, cadmium recovery and melting. The oxide section of the plant, treating zinc fume from re-treatment of lead blast-furnace slag, is practically a separate zinc plant; this is necessary because of the presence of fluorine in the smelter zinc fume. Cadmium is recovered electrolytically from the purification residues of both the sulphide and oxide leaching plants.

Jan 1, 1937

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method. CONSIDERING the subject alone, this paper would cover only a mechanical treatise of pillar roping. Because the St. Joseph Lead Co. originated the practice, it is proper to give a short introduction to the company. It is also proper to describe pillars and discuss their purpose to justify expending large sums of money to preserve them after the surrounding area has been thoroughly mined. Because the St. Joseph Lead Co. originated the practice of back pinning with wedge bolts, patch plates and channel irons, and the pouring of substitute pillars of concrete, these too, are mentioned. The Southeast Missouri Division of the St. Joseph Lead Co. is the largest lead producer in the United States. About 95 pct of the present producing mines are in St. Francois County, which begins 60 miles south of St. Louis. The entire lead ore production of this county, at the present time, is mined and milled by this company, treatment plant capacity being about 22,000 tons per day. This area is also the oldest, lead having been mined at Mine La Motte, in Madison County, in 1723. Estimated production of all the various companies that have mined here is about 7,000,000 short tons of pig lead. Method of Mining The lead occurs in the ore as galena. Galena is found either in the form of disseminated or solid streaks, of varying thickness. Ore stratum is the Bonne Terre dolomite, which is about 350 ft thick, but almost all the ore is in the lower 100 ft. Ore is mined by room and pillar method in open stopes. These stopes vary in height from 7 ft to 200 ft, depending on the thickness of the pay ore in that spot. Back, or roof, is supported entirely by pillars. In a majority of stopes, after the loose scales are mined down, the back has remained solid for many years (fig. 1). Under ideal conditions pillars are spaced to form an equilateral triangle and are as small and as far apart as the height of the stope and the character of the back will permit. They vary in diameter from 10 ft to 50 ft and are from 18 ft to 50 ft apart, measured from the outer edges. In general, the pillars are approximately 12 ft in diameter, and 25 ft apart. The spacing is very uncertain because of the vagaries of the ore trend, the desire to better support breaks in the back, and the attempt to spot out the thinner ore by not placing one in the core of the ore body. Use of Structural Steel Channels In stopes where the back is bad because the overlying formations are thin with wet, weak and shaly

Jan 1, 1951

By A. W. Jenike

A theory of gravity flow of bulk solids like ores, concentrates, coal is outlined and an example of design for unobstructed flow is given. Mass-flow and plug-flow patterns are defined and related to the geometry of the bin. The effect of these patterns on segregation, first in-first out flow, and caking is described. This paper is a report on the results from the AIME sponsored project "Flow of Bulk Solids" which was carried out under the author's direction at the Utah Engineering Experiment Station, University of Utah, during the period 1956-1962. The theory has been applied to the design of numerous industrial storage plants. A QUANTITATIVE METHOD OF DESIGN FOR FLOW There is hardly an industry which does not store and handle solid materials in bulk form. When the volume of the solids is large, gravity is invariably relied upon to cause the solids to flow out of storage, through channels and chemical reactors. Such materials as ore, coal, cement, flour, plastics, clay, soil, to which a general term of bulk solids is applied, flow by gravity or are expected to flow by gravity in thousands of installations and by billions of tons annually. The chemical and process industry depends on gravity flow of solids in process and out of storage. Mining relies on gravity flow in block-caving, in ore passes, as well as in storage and loading bins. Agriculture uses gravity flow in elevators, in feed plants, and in farm silos. In practice, satisfactory gravity flow is seldom attained. Such problems as doming, piping (rat-holing), lack of live capacity, segregation, deterioration in storage, harass industry. In spite of the universality of these problems, until recently, there has been no theory of solids flow, no method of predicting how a solid would behave, and how the channel, bin, or hopper should be designed. In the late nineteen forties and early fifties, the theory of plasticity came of age and simultaneously the computer became widely available. These two factors permitted the development of a theory of flow of bulk solids. The work was conducted during the years 1953-1961. In conjunction with the development of the theory a method to measure the flowability of solids was also developed1-7 and the theory was ap-plied to the design of ore pockets, storage plants,16 chemical reactors and adsorption columns. A comprehensive report of this work is given in a previous work." THEORY OF FLOW The most important question which a theory of flow has to answer is: what conditions need to be satisfied for a given solid to flow uniformly and without obstructions through a channel? First of all, the following observations are made:

Jan 1, 1967

By R. V. McAfee

The fundamentals of vertical-lift performance are examined with the aid of computer-calculated flowing gradient charts. Flowing and gas-lift well performance characteristics are determined from available well test data. The effect of tubing size, gas-liquid ratio and wellhead pressure is discussed for both flowing and gas-lift wells. The effect of gas-injection pressure, formation gas, bottom-hole pressure and valve spacing is also discussed for gas lift wells. From these studies conclusions may be reached for improving or prolonging natural flow, obtaining optimum lift efficiency when natural flow ceases and improving existing gas-lift systems. The techniques perfected satisfy the requirement that the time involved to conduct an evaluation be practical for operating personnel. INTRODUCTION Flowing pressure gradients furnish the key to successful evaluation of vertical-lift performance in producing wells. Command of multiphase flow gradients in some readily usable form is a necessity before operating personnel can competently include vertical-lift performance evaluation of both flowing and artificial-lift wells in their over-all consideration of production efficiency. A readily usable form cannot be overemphasized since most of the decisions which confront the production engineer with a problem well must be made quickly. In moving a barrel of oil from the reservoir to the stock tank, the major portion of energy generally is expended in the vertical-lift phase. This may or may not be of concern during the flowing life of a well, depending upon the production requirements. It becomes of some concern when the flow performance of the well becomes erratic, and a conscious effort must be made to maintain natural flow. It is at this time that the first steps may be taken to modify existing conditions to relieve unnecessary limitations to proper flow. When natural flow ceases and some form of artificial lift must be installed, the amount of energy expended in lifting liquids becomes quite obvious. It is at this time, if no other, that lifting efficiency becomes important because that part which must be supplied from an outside source is now related directly as a cost per barrel of oil produced. Ten years ago, the majority of gas-lift wells were produced with gas-well gas. Today, the majority are produced by closed rotative gas-lift systems. This permits a direct evaluation of well performance in terms of horsepower requirements and has resulted in mixed conclusions as to the success of gas lift based upon the relative efficiency of a particular system. An increased awareness of the need to resolve vertical-lift performance on a readily usable, scientific basis was inevitable. An indication of the need for better applied science in this field is the often-asked question of whether or not gas-lift can efficiently deplete a given well or reservoir. This question cannot possibly be answered without first evaluating reservoir, surface and vertical-lift performance both as encountered today and as anticipated throughout the life of the well or wells. The technique presented in this paper was originally developed to upgrade gas-lift installation design from an applied art to an applied science. It has since been successfully used not only for this purpose, but also for the whole field of vertical-lift performance in its broadest sense. Lift efficiency should be considered important while the well is still flowing, as well as after natural flow ceases. Correct interpretation and proper modification of the vertical-lift performance of a producing well can provide dramatic improvement in production performance and/or efficiency. STATEMENT OF THEORY AND DEFINITIONS Fig. 1 illustrates the three divisions of production which will be used in this paper. The terms are a modified version of those presented in the very fine paper by Gilbert.' The fields of reservoir and surface performance both have been greatly improved over the years. A study of those writings which may be found indicates that the field of vertical-lift performance has not progressed as well. There are two possible reasons for this lack of progress. 1. It has not been recognized as a scientific field in itself by the oil companies, as has reservoir engineering. 2. The equipment companies have confined their efforts to mechanical design research rather than the more basic study of vertical-lift performance of producing wells. Both organizations must have an economic stimulus for doing research in this field, and most of the results obtained in past work has been so erratic as to arouse little enthusiasm. The basic purpose of interpreting vertical-lift performance is to predict operating conditions below the surface of the ground from available data. The success of the interpretation depends upon the accuracy with

By Lawrence A. Roe

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% SiO2, 31.89% MgO, and 4.75% H2O. However, as an industrial commodity, talc rarely approaches theoretical purity. Nevertheless, the impure talc products of commerce find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are tremolite, chlorite, dolomite, mica, and magnesite. Steatite was originally a mineralogical name applied to pure talc. In today's commerce steatite generally refers to the massive variety of talc suitable for electrical insulator manufacture. Block steatite ore can be machined into various shapes. Impure varieties of massive or block talc are still commonly referred to as soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soapstone and talc, this is a natural thing since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as "slip") have been grouped together and called soapstone or talc. Further, there is a mineralogical relationship of pyrophyllite to montmorillonite and talc to hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Indians on Santa Catalina Island, Calif. In the mid-1800s, soapstone from deposits along the western foothills of the Sierra Nevada mountains was used by white settlers for building and ornamental stone and in the linings and foundations of furnaces (Anon. 1956). Previous to 1916, the annual recorded production in California did not exceed 2000 tons. In the period 1912 to 1918, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 9,000 to 20,000 tons. In the mid-1930s, the use of talc in wall tile grew rapidly. In California, the production of talc grew to 63,000 tpy in 1943. The post-war building boom helped California production to grow to 120,000 tons in 1951. In 1968, production was 165,000 tons, 1969 was 145,000 tons, 1970 was 185,000 tons, and 1972 was 155,000 tons. Talc mining in New York state dates to about 1878 when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville, New York. In 1893, this operation was sold to the International Pulp Co. which changed its name to the International Talc Co. in 1944. Total production from seven New York mines, in 1948, was 130,000 tons. A new talc operation, the Gouverneur Talc Co. owned by the R.T. Vanderbilt Co., began operations near Balmat, N.Y., in 1948. The initial capacity of the processing plant was 200 tpd (Gillingham, 1950). Subsequent expansions have increased capacity to over 600 tpd. The Vermont talc industry began just after the start of the 20th century. Talc was discovered in the area of the present Johnson, Vt., talc mine in 1902. The American Min¬erals Co. initiated plant operations at Johnson in 1904. The Magnesia Talc Co. opened a plant at Waterbury, Vt., in 1913 (Burmeister, 1963; Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine has a long history as a producer of talc crayons. The Eastern Magnesia Talc Co. was formed in 1924 by a merger of the Eastern Talc Co.

Jan 1, 1975