Search Documents

By Horace Mann

A FEW years ago, it was generally thought that from 15 to 18 per, cent. of zinc oxide was the upper limit of a workable lead blast-furnace slag. With slags above this zinc-oxide content, the furnaces gave so much trouble because of hearth, wall, and crucible accretions that the campaign was very short. The time lost in cleaning out the frozen furnaces, for it was seldom possible to blow them out, and blowing in was so great that it was considered uneconomical to attempt the running of high-zinc slags, even if this were metallurgically possible. It is true that there are, references to one or two slags much higher in zinc than the foregoing,1 but the average smelterman regarded these, as freaks and not to be considered for regular furnace work. One or two plants, notably the plant of the United States Smelting Co, at Canyon City, Colo., ran charges, higher in zinc. At this plant, the zinc-oxide content of the charge was frequently 20 per cent. and higher but the slags from these furnace's seldom ran over 10 to 12 per. cent. zinc oxide. The furnaces were run with a large volume of air under a relatively low pressure, a low smelting column, and a very hot top; as a result, a large amount of zinc was volatilized. Even with the low smelting column and hot top, accretions caused much trouble and barring, down was a daily occurrence. At the time most of the theories on lead blast-furnace work were promulgated or worked out, it was necessary to run a furnace with a cold top in order to avoid an excessive loss due to fines and fume. At the same time, the smelting conditions had to be such that the lead and silver would be reduced and would enter the bullion. The slag had to be liquid but the charge must not give excessive accretions either in the hearth or on the walls of the furnace. This forced the operators to run the furnaces with a comparatively low blast, which, in turn, caused a small fuel consumption per unit of time with the accompanying result of a low working temperature.

Jan 8, 1925

By Frank C. Schrader

Page Introduction.............................. 196 Geology of the District......................... 196 Ore Deposits of the District....................... 198 Gcncral Description........................ 198 The Cerbat Mountains Group................... 199 General Description...................... 199 Tennessee Mine....................... 203 Midnight Mine........................ 203 Mineral Park........................ 204- Golconda Mine........................ 204 Other Ore-bearing Districts.................. 205 Lost Basin District ...................... 205 The Black Mountains Group.................... 206 Tom Reed-Gold Road District...................... 208 General Dcscription........................ 208 Development........................... 209 Topograplly............................ 210 Geology.............................. 210 Ore Deposits........................... 213 General Dwcription...................... 213 Zones.......................:....215 Structure of Ore Shoots.................... 217 Gold Road Mine ......................... 218 General Description...................... 218 Geology........................... 218 Ore Deposits......................... 219 Tom Reed Minc......................... 222 General Description..................... 222 • Ore Deposits.......................... 222 Development......................... 223 Character of Ore....................... 224 Other Mines........................... 224 Fields Similar to the Ton1 Reed-Gold Road District......... 227

Jan 1, 1917

By Francis Foley

Small cracks in a plane normal to the axis of steels are found to be prevalent around the water hole of drill steels that have been in service for an unknown period of time. Cracks are not found on the exterior surface of the steels nor to any noteworthy extent even in the water holes of new drill steels. Undulations and serrations are found in the surface of the water hole in new steels; it is in the bottom of such defects that cracks appear to develop in used steels. The occurrence of the more serious of these cracks at the point in the steel to which it has been heated for forging or hardening is thought to account to a great extent for failures in that region. DURING the past, year, we have investigated the cause of 88 per cent, of the failures by breakage near the bit end of some 1-in. hollow, hexagon, drill steel used in a metal mine. This breakage in the region of the bit end of the steel was peculiarly interesting because we have been led to believe that breakage is most prevalent at the shank end of drill steels near the place where the steel is gripped in the chuck of the machine. Records from the mine showed, also, that the breakage was much more frequent in the short lengths of large gage than in the longer steels; this is shown graphically in Fig. 1. Because the shorter lengths of steels are usually those that have been made from broken pieces of long steels or from steels that have worn down in service, rarely being made from new stock, those who are wont to suspect steel of tiring and crystallizing in its old age through fatigue are quite apt to see in this instance an argument in favor of their idea. As usual, a careful examination of these steels reveals defects of a character hardly to be overlooked in favor of such a cause. The steel in question was rolled with a sand core and was of the usual drill steel composition: Carbon 0.85 per cent., manganese 0.60 per cent., silicon 0.25 per cent., phosphorus 0.02 per cent., and sulfur 0.02 per cent., with the exception that in some specimens there was vanadium, not exceeding 0.20 per cent.

Jan 3, 1924

By William Fink

NICKEL is used as an alloying element in several complex commercial aluminum alloys, among which are found some very interesting proper-ties, such as relatively high strength at elevated temperatures, relatively low coefficient of expansion, the absence of permanent growth, ability to take a good polish, and a bright, pleasing as-cast surface. For that reason the aluminum-nickel system was included in the list of binary aluminum systems that are being studied as a preparation for the investigation of more complex commercial alloys. This paper is the fifteenth of a series from the Research Laboratories of the Aluminum Company of America reporting the results of investiga-tions of equilibrium relations in aluminum-base alloys of high purity. The aluminum-nickel equilibrium diagram from 0 to 18 per cent nickel was determined, using the purest material available.

Jan 1, 1934

By Thomas F. Torries, George H. K. Schenck

Crushed and broken stone is used directly in construction as an aggregate and accounts for about half the value and two-fifths of the quantity of natural aggregates consumed in the United States. Sand and gravel provide most of the balance of aggregates except for some lightweight materials such as pumice and expanded shale. Conditions necessary for production of crushed stone from a deposit are : 1) Quality-should pass rigid specifications for strength and durability. 2) Cost-low average total delivered cost. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass either (1) by the addition of cementing or binding materials that produce a concrete or (2) by compaction or by natural weight to produce a road base or foundation. Aggregates usually provide about 80 to 100% of the material volume of the construction masses in which they are used. The construction industry utilizes as aggregates about 70% of all crushed stone produced in the United States according to statistics provided by the U.S. Bureau of Mines (USBM) , [Table 1], using definitions as shown below. Nonconstruction uses of crushed stone, [Table 2], are included elsewhere in Industrial Minerals and Rocks because such uses require the special physical or chemical characteristics which are discussed in those chapters.

Jan 1, 1975

By Pol Duwez, Howard E. Martens

INTRODUCTION THE high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method .of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to be cooled of a porous material, so that the cooling fluid can be forced through the pores. In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat. This method, referred to as "sweat cooling," was proposed at the jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very dose control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of pressure drop. Generally, the proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequently the permeability of the porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1948

By David R. Mitchell

THIS paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual,1 it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. HISTORICAL SUMMARY The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and sizing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

OF THE many categories into which scientific knowledge has been arbitrarily divided, the one which has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. To one who has had no such course or whose auld acquaintance with the subject has all but been forgot, such application is all too often thwarted by the abstruse presentations of the subject found in many of the available textbooks. AS a tool for the control of a complex process involving many chemical reactions, physical chemistry can become very valuable. The specialist who is using this tool for many purposes and perhaps contributing to its development will want to know a great deal more about it than can be included in this book. He will be interested in its history, its accomplishments and limitations, and its applications to many and varied problems. To the steelmaker or metallurgist, however, it is only one of a number of tools that he must use. He is willing to forego the detailed study of its inner workings in order to concentrate upon the development of skill in its application. It is the purpose of this chapter to present a simplified view of physical chemistry as a tool of great potential usefulness. This purpose and the desire for brevity have required the elimination of many of the gadgets with which the tool is usually adorned. It is hoped that this simplification will be conducive to clear understanding. The beginner is urged not to overlook the more extended treatments of the standard textbooks.* He is assured at the same time that the basic tool is sound and serviceable and is guaranteed to give satisfaction if regularly lubricated with common sense. Certain parts of physical chemistry require rather formidable mathematics for their complete development, but in the main those applications in which we are here interested can be expressed in fairly

Jan 1, 1944

By H. O. Hofman

In the blast-furnace smelting of lead, copper and other non-ferrous metals, the largest part of the product obtained is slag. Its formation consumes more of the heat-energy of the fuel charged than any other chemical reaction that takes place. It is therefore of importance to know at what temperatures the different slags will form, so as to be able to choose in a given case the slag that will form at the right point in the operation, will keep the products thoroughly fluid, so as to insure a satisfactory separation, and will permit the consumption of fuel to be reduced to the lowest practicable point. While practical experience has brought out in a general way the leading differences as to the formation-temperatures of Rome silica—iron —lime slags, accurate details are still wanting. The object of the investigation here described was to supply some of these.* Prominent among the men who have worked on the fusibility of silicates are Lampadius, † Sefström,‡ Berthier,§

Jan 1, 1900

By L. J. Parkinson

IN striking contrast to American mining engineering schools, in Europe a new president, known as the Rektor Magnificus, is elected each year or alternate year. An exception is Italy, where election is for a period of three years. The Rektor, who is elected by the full professors, must also be a professor and full-time member of the faculty. In most cases there is a Senate, composed of 5 to 14 full professors, some elected and some appointed, which controls the Rektor in policy decisions, but in some institutions there is no such controlling body. In the same way deans for each faculty or college are selected at the same intervals from among the full professors concerned.

Jan 1, 1958

By Benjamin Smith Lyman

It has seemed that it might be a highly useful contribution to the study of structural geology to assemble, in as compact a form and on as large a scale as practicable, a great number of

Jan 1, 1896

By J. L. Byers

THE metals of the platinum group, ruthenium, rhodium, palladium, osmium, iridium and platinum, have certain characteristic effects on the structure and appearance of the cupellation bead. These effects are dependent not only on the particular member of the group present, but also on its concentration. The extent and quality of these effects, however, have not received investigation worthy of their importance. Bannister and Patching investigated the qualitative effects of some of these metals in 1913. This paper deals with a possible rapid qualitative and quantitative delineation of the effects exerted on the cupellation bead by the various metals in the platinum group. More particularly, the paper correlates quantitatively the presence of such metals with their characteristic structural and surface effects. Inasmuch as the various members of the group are more frequently associated with gold than with silver, the gold button will receive the greater consideration. The past two decades have seen a much greater interest manifested in this particular group of metals, because of the increased industrial demand for them. There has been a constantly growing need for assays that will not only express the silver and gold values but also indicate the presence of the other metals. If these indications could be used as quantitative criteria, their value would be greatly increased, because the methods of chemical analysis for the elements of the platinum group are lengthy, involved and unreliable except when the analysis is made by an expert and experienced rare-metal analyst. The materials for the X-ray diffraction examination of the different beads were prepared by filing and screening to -200 mesh, and were then rayed in a General Electric X-ray diffraction unit. The filed samples were treated magnetically in order to eliminate any possible steel particles. Sodium chloride and C.P. gold and silver were used as standard comparators.2 (See Table 1.)

Jan 1, 1932

By D. N. Collins, J. R. Stevens

New expressions in the technical assessment of mineral concentration processes have been defined as Concentration Efficiency: Concentration Index: where h is the percentage of head grade; c, percentage of concentrate grade; maximum percentage of concentrate grade obtainable at 100 pct recovery; and R, percentage of recovery. In developing these expressions, the basic requirements for the technical assessment of concentration operations have been defined and the various expressions suggested by others for asses-sing the results of such operations reviewed and criticized. The derived expression for E, depends on a simple combination of recovery (R) and a new term selectivity (s), where S is (c-h)/(c,,, -h), by definition. Limitations of the new expressions are discussed and examples given of applications to concentration operations. It is also shown that the formulae for E, and I, can be applied to scatter diagrams, multi-component systems, size-assay analyses, and classification data. Many methods of quantifying concentrating operations have been proposed. These include direct presentation of weights and assays together with the derived data for other items such as ratio of concentration, recovery, rejection losses, and enrichment ratio. These terms are now accepted mineral dressing nomenclature, and in the assessment of the results of concentration processes, concentrate grade and recovery are together the most widely accepted measures of concentration efficiency. For practical purposes when the concentrate grade is equal to or greater than a predetermined acceptable value, test or operation results may be assessed by the recovery figures alone. Similarly when recovery is within specification, the operation can be assessed by concentrate grade. The ultimate assessment and selection of a concentration operation is—admittedly with a few ex-ceptions—a matter of economics. There is however an intermediate stage in laboratory and pilot plant testing when evaluations must be made without the assistance of an economic yardstick. Numerous techniques are employed to facilitate such evaluations among which may be mentioned graphical plots of grade vs recovery, cumulative weight vs cumulative recovery, scatter diagrams, etc. The desirability of combining metallurgical results and product weights and assays into a single value has been recognized and discussed by many workers1-" with the resultant suggestion and use of such terms as Metallurgical Efficiency ,' Summation Index,' Selectivity Index,'- and Absolute Efficiency B None of these expressions completely satisfies all the requirements of a selectivity or efficiency formula and it is proposed in this report to define the terms, relating to the technical efficiency of a concentrating operation, concentration index and concentration efficiency. Examples are given of their application and a comparison is made of their use in relation to other formulae. All product grades in this paper will be referred to in terms of mineral percentages and a list of symbols is given in Table I. CONSIDERATION OF EXISTING FORMULAE A number of the existing efficiency and index terms used in quantifying concentrating operations are considered below. Metallurgical Efficiency:

Jan 1, 1961

By W. S. Ayres

The construction of a new breaker at the Cranberry Colliery, Hazleton, Pa., was forced upon the operators, A. Pnrdee & Co., by a fire which destroyed the entire plant early in January, 1896. The loss included, in addition to the breaker, three boilerhouses and three engine-houses. The boilers were not injured, but the steam-pipes and connections were all broken and warped by the fire. The boilers were probably saved from injury by the presence of mind of the fireman., who started all his feed-pumps and filled the boilers with water. The hoisting-engines were more or less warped and cracked, but by patching and replacing the injured and broken parts, they were made to do satisfactory service in the new plant. It may be worthy of mention that the wrought-iron shaft of one of the hoisting-drums, 12 inches in diameter by 17 feet long, was so heated in the fire that the weight of the drum caused it

Jan 1, 1899

By Arthur F. Daily

13.5-1. Placer Deposits-Definitions. Placers are defined for this chapter as unconsolidated deposits of detrital material containing valuable mineral, and placer mining is defined as surface exploitation of placer deposits. Unconsolidated marine deposits containing industrial minerals, such as the very large pebble phosphate beds in Florida, pelletal phosphate beds in the Sechura Desert in northwestern Peru, oyster shell beds occurring at many places, and nodules resting in the sea floor, are not classed herein as placer deposits, though methods commonly used for mining placers may be employed for their exploitation. The natural processes that may form placers range from chemical weathering to stream, marine, and wind action, and combinations thereof, resulting in some degree of concentration of valuable mineral. One or more cycles of erosion and deposition may have occured. In relation to mining, placers include unconsolidated barren or near-barren overburden and underlying weathered bedrock. Placers of any origin subsequently may become drowned by the sea and then partly or entirely covered by marine deposits; or they may become covered with alluvium, eolian deposits, or lava. The mining of placer deposits for valuable mineral content usually is followed immediately by primary concentration using wet (rarely dry) gravity methods, succeeded by secondary concentration employing both gravity and other methods. 13.5-2. Classification of Placers. A fundamental classification of placers according to genetic types follows; some degree of concentration occurs during formation of all except saprolite and some moraines. 1. Saprolite and residual placers, consisting of mineralized rock decomposed in situ principally by chemical weathering; respectively either without change in volume, or slumped because of dissolution of some constitutent.

Jan 1, 1968

Jan 1, 1893

By Maurice K. Seguin

It is a difficult task to find enriched soft iron ore deposits in the central part of the Labrador Trough, New Quebec, Canada, when the areas investigated are covered by glacial drift. A qualitative interpretation of either a combined gravity-magnetic-seismic-resistivity survey or gravity-magnetic-seismic or gravity-magnetic-resistivity survey permits (with a low probability level) the detection of iron formations and ore zones as well as their delineation from most of the country rocks. This is possible because most of the altered iron formation underwent a slight increase in density through enrichment and because the accompanying geochemical alteration changed their magnetic properties. In order to increase the chances of success in finding ore bodies when using geophysical methods, different types of correlation were done for many deposits. These are: I) A quantitative correlation of the residual gravity anomaly intensities with the specific gravity, the iron content, the silica content, the porosity factor, and the dimensions of the underlying ore bodies. 2) A quantitative correlation of the ground magnetic intensity relative to a reference lithologic unit with the percentage of Fe.,O, recovery and with the volume ferromagnetic susceptibility. A few discoveries already have been made with this method. The details of the location, the description of the geology, and the history of previous geophysical surveys and their qualitative interpretation have already been given.', ' A very brief paragraph describing the regional and local geology is necessary in order to facilitate the understanding of this paper. The sedimentary iron formations of the Labrador Trough consist of a 700-mile geosynclinal segment composed of tightly folded and faulted Proterozoic sediments, volcanics, and intrusives that are rich in mineral deposits. The complex sequence rests unconformably on the basement of Archean granitic gneisses. The direct-shipping iron deposits are scattered along a northwest-trending strip, 5 to 10 miles wide and some 60 miles long in the facies rich in iron oxides and preferentially in localities where the original sedimentary environment favorized the deposition of a large concentration of magnetite associated with chert by physicochemical processes, e.g., oxidation-reduction potential, pH, temperature, pressure. Once leached of its silica and/or iron carbonate content and enriched with secondary a-hematite (occasionally goethite), this original magnetite associated with some primary hematite makes the blue direct-shipping ore which constitutes the important ore reserves in this mining district.

Jan 1, 1971

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By C. C. Henning

IN any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel con-stitutes a large volume of tonnage in daily use. There is a fairly prev-alent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applica-tions sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat treating, particularly carburizing, is performed on this grade.

Jan 1, 1935

By H. A. Wheeler

History ILLINOIS has so recently attained the third place in the oil production of the United States that few realize its great importance, or are aware of its highly profitable character. Since 1907 Illinois has furnished about 15 per cent. of the United States output and about 10 per cent. of the world's production. The value of the output in 1913 is estimated at $30,000,000, of which about $20,000,000 is profit. The present prosperity dates from 1905, but efforts have been made since 1865 to develop production and geologists have been very sanguine as to its future for over 25 years. Had the oil operators been as confident as the geologists, the field would have been opened at least 30 years earlier. For the rich Eastern Illinois oil field is located along the La Salle anticline, that was mapped 46 years ago by Professor Worthen in the

Jan 5, 1914