Search Documents

By N. J. Themelis, P. Spira

The efficiency of the reverberatory furnace operation in producing. slags of 1020 copper content depends on the mixing and flow conditions in the bath. Radioactize-tmcer tests have indicated the jkaction of bath volume engaged inflow and the mixing conditions in the bath. The factors controlling the flow pattern of slag have been classified as laminar transfer flow, natrsral convection, and flou, due to the rapid addition or removal of slag.. Similarity criteria for model studies have been developed. The pyrometallurgical processing of copper begins with the smelting of either flotation concentrates, or direct-smelting ores which have been partially roasted to calcines. These materials are generally smelted in a reverberatory furnace, Fig. 1, and separate into two liquid phases, a sulfide matte and an iron silicate slag. he matte is tapped and subsequently reduced to metallic copper in a converter, while the reverberatory slag is usually discarded without any further treatment. Molten slag from the converting operation is returned intermittently to the reverberatory in order to recover its high copper content (1 to 3 pct Cu). The reverberatory furnace is about 115 ft long by 30 ft wide. In general, the solid charge is fed at intervals through openings along the sides of the roof and forms sloping banks from which the molten materials trickle down into the bath; the charge banks extend over a length of about 70 ft from the firing wall. The depth of the slag and matte layers varies from smelter to smelter; in the Noranda furnaces, the slag depth is 24 to 30 in., while the depth of matte at the taphole is about 20 in. Apart from smelting, the functions of the reverberatory are to recover most of the copper content in the converter slag by physical and chemical interaction with the furnace bath, and to provide adequate time for optimum separation between matte and slag. The efficiency of these operations depends on the mixing and flow conditions in the bath and is reflected on the copper losses in the slag. In the present study, the reverberatory furnace is considered as an open-channel chemical reactor and the driving forces for material transport through the bath are examined by means of flow and mathematical models. FLOW CONDITIONS IN THE REVERBERATORY FURNACE To facilitate the study of mixing conditions in continuous-flow reactors, two idealized patterns of flow have been accepted by workers in this field.' The term "backmix" flow is used to describe complete and instantaneous mixing in the reactor (perfect mixing); all particles have the same chance of leaving the system, independently of their time of entrance, and the fluid is uniform in composition throughout the vessel. On the other hand, "plug" flow, or "piston" flow, assumes that a fluid element moves through the reactor without overtaking or mixing with fluid entering at an earlier or later time. In addition to the two idealized patterns of flow, "deadwater" flow accounts for that portion of the fluid which is moving so slowly that it may be assumed to be stagnant. According to the definition by evensppiel,' the cut-off point between active and stagnant fluid may be taken as material which stays in the vessel for a period twice the mean residence time. The flow patterns in real vessels may be approximated by a combination of the above flows. Thus, the vessel is assumed to consist of interconnected flow regions with various modes of flow existing between them. The flow pattern may be determined directly from the flow paths of fluid through the essel. -However, the difficulty of obtaining and interpreting such information has led to the alternate approach of determining the residence time distribution of fluid elements by means of stimulus-response studies. The stimulus is provided by introducing a tracer in the inlet stream and the response by the record of the change in tracer concentration in the exit stream from the reactor. Such tests have been conducted in glass tank furnaces using either chemical7"9 or radioactive tracers1'-'' and, in one case, experiments have been reported for a metallurgical furnace.'"

Jan 1, 1967

By Peter Tegart

The discovery of gold in the Toodoggone River area is credited to Charles McClair who mined placer deposits in 1925, reportedly valued at $17,500. After he and his partner went missing in 1927, efforts to relocate their workings resulted in the formation of Two Brothers Valley Gold Mines Ltd. in 1933, in which the legendary Grant McConachie (first president of CP Air) played an active role. This was the age when the prospector first utilized the airplane to reconnoitre remote areas. What greeted the observer from the air was an area rich in orange and yellow colours characteristic of gossans formed by the oxidation of sulphides. However, Samuel Black, a Hudson Bay Company fur trader, had also noted in his diary as early as 1824, the unusual and many gossanous colours in the headwaters of the Finlay River. These gossans, coupled with white limestone bluffs and the presence of placer gold, attracted the first reconnaissance of the area by Cominco in 1929. Cominco was ever active in remote areas at this time. They staked and worked several base-metal showings hosted by limestone at the margins of intrusive stocks. These early workers also obtained erratic high gold assays from chalcedony float samples found in creeks draining into the Toodoggone River. However, because the samples gave inconsistent assays, no concerted effort was made to locate their source. Except for the occasional horse-supported prospecting party of the late 1940s and early 1950s, the area did not receive much attention until 1968. Work until this time focused on the base metal lead-zinc showings which contained attractive silver credits. Gold was not an attraction because of the set price established by the US government. The late 1960s saw the northward expansion of porphyry copper exploration into the Toodoggone. A program of gossan soil sampling (gossans which had attracted the early workers) was carried out by Kennco Explorations (Western) Ltd. in 1966-1967. They analysed for base metals in the field, using a cold extraction method. The Kemess copper- gold prospect was staked as a result of anomalous copper values from this early geochemical program. In 1968, Kennco continued the program of silt traversing and field geochemical testing. The samples were further subjected to multielement analysis consisting of copper, molybdenum, lead, zinc, cobalt, nickel, and silver at Kennco's North Vancouver laboratory. Several anomalous creeks, high in combinations of copper, molybdenum, and silver, were outlined. Some initial soil grids were also established. The fall of 1969 saw the return of Kennco prospector Gordon Davies and geologist Bob Stevenson to check out a well-defined molybdenum, scattered copper and silver anomaly in soils from a grid on the Chappelle claims. The subsequent analysis of several selected quartz felsenmeer floats yielded one assay which ran in the order of 0.25 kg/t (8 oz per st) gold and 2.2 kg/t (70 oz per st) silver. Subsequent trenching on the Chappelle claims exposed the source of float in a 4- m (134) wide vein of high grade gold-silver mineralization. These results led quickly to the realization that the district had precious metal potential. Subsequent exploration in the period 1969-1974 by Kennco resulted in the discovery of most of the gold and silver occurrences on the Chappelle and Lawyers properties. Several other gold and silver occurrences were found in this district by Cordilleran, Cominco, and Sumitomo, working the district during this period. Conwest optioned the Chappelle in 1973 and explored underground by adit entry as part of a one-year program. In 1974, Du Pont of Canada Exploration Ltd. optioned the Chappelle claims and in March 1980, using reserves developed on the A vein, placed the Baker mine into production at a rate of 90.7 Vd (100 stpd). The Amethyst zone on the Lawyers property, 8 km (5 miles) north of Chappelle, was found in 1973 by Kennco using continued, persistent followup prospecting of silver silt geochemical anomalies. A silt anomaly in the order of 3.4 ppm silver occurred in a stream flowing 300 m (984 ft)

Jan 1, 1985

By Raymond L. Orr

Calorimetric measurements have been made of the heats of solution of gold axd indium in a number of liquid tin-rich alloys at a temperature of 705°K. Relative partial molar enthalpies of gold were determined as a function of dilute solute concentrations in the binary Au-Sn system and in the ternary Ag-Au-Sn and Au-In-Sn systems. Relative partial molar enthalpies of indium were determined for dilute solute concentrations in the In-Sn, Ag-In-Sn, and Au-In-Sn systems. Through application of the interaction coefficient concept introduced by Wagner and more recently extended by Lupis and Elliott, ualues have been obtained for the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. The results are inte@reted in terms of solute atom distributions through comparisons with the predictions of dilute solution models. INTEREST in the thermodynamic behavior of dilute liquid alloys stems from two primary sources. From a practical viewpoint, it is often of importance to know or to be able to predict the effect that one solute will have on the thermodynamic properties of the other solutes in a multicomponent system. Studies of dilute solutions may also be rewarding from the theoretical point of view. Some of the difficulties arising from the more complex interactions possible in concentrated solutions are avoided, leading to easier interpretations in terms of solutibn models and bonding energies. For example, in a binary alloy the limiting values of the partial molar properties of the solute represent the case for which each solute atom is completely surrounded by atoms of the solvent, and no other interactions are possible. Solute - solute interactions in dilute solutions are conveniently treated by the interaction coefficient concept of ~agner.' Using a Taylor series expansion for the logarithm of the activity coefficient, In yi, of a component, i, in a solution consisting of dilute solutes with atomic fractions xi, xj, xk, and so forth, in a solvent, s, and neglecting the second- and higher-order terms, Wagner obtained the expression: Where Wheyz is the limiting value of yi in the pure solvent, s. The interaction coefficients, e:, e:, and so forth, are defined by: Since yi is related to the excess partial molar Gibbs energy of component i by GfS = RT In yi, E: is re- ferred to as the "Gibbs energy interaction coefficient". Lupis and Elliott~ extended Wagner's treatment to the relative partial molar enthalpy, aHi, and the excess partial molar entropy, qS. They defined the enthalpy interaction coefficient as: and the excess entropy interaction coefficient as: leading to expressions similar to Eq. [I]: The three interaction coefficients are related by? The self-interaction coefficients, E:,qf,and at, represent the effects of interactions between atoms of component i in solvent s; €3, q{, and 03 represent the effects of interactions between i and j atoms in solvent s; and so forth. From the Maxwell-type relationships between partial molar quantities, it may be shown1'2 that e{ = ej, r}\ =tj), and ai - crj. Experimental determination of the interaction coefficients requires extremely precise measurements of the appropriate properties as functions of solute concentrations in very dilute regions. Few such data exist for intermetallic alloys, even for binary systems, because of experimental difficulties. This is especially true with respect to enthalpy data for dilute alloys. Examination of the compilation of data for binary alloys by Hultgren, Orr, Anderson, and ~elle~~ reveals that determination of limiting values of &fii(Xi =0) often requires extrapolations to infinite dilution from xi = 0.05 to 0.10. Direct measurements of the enthalpy interaction coefficient, qi, for multicomponent systems are virtually nonexistent. This quantity is of course subject to direct calorimetric measurement, but its determination must be limited to cases where high experimental precision is possible. The heats of solution of gold and indium in liquid tin can be measured with relatively high precision, which makes determinations of 73 involving these metals as the measured solutes experimentally attractive. This paper presents the results of such determinations of the Au-Au, Ag-Au, Au-In, and Ag-In enthalpy interaction coefficients in liquid tin. MODELS FOR DILUTE-SOLUTION BEHAVIOR Random-Solution Behavior. In the quasi-chemical treatment of solutions, only nearest-neighbor bonds are considered, and a composition independent value

Jan 1, 1967

By N. Plint, E. T. Pinkney

Copper segregation developments within the Anglo American Group are described with particular reference to the work of the TORCO Project Team. Some radical differences have been adopted in the mechan-ical approach as compared with methods used by previous workers. Most important among these are the following: (1) The heating unit is a fluidized-bed roaster. (2) A moving bed segregation chamber is used in which a packed bed of heated ore, to which reagents have been added, moves slowly downwards under gravity and is discharged at a controlled rate by means of a suitable valve mechanism. (3) The quantities of reagents used (sodium chloride and some form of carbon) are only a small fraction of those recommended by other investigators. (4) Retention times of only 2 min have been satisfactory for the complete segregation of many types of ore. Project TORCO is the code name given by Anglo American Corp. of South Africa, Ltd., to the investigation undertaken in Zambia to develop a plant capable of treating large tonnages of refractory copper-bearing ores by the segregation process. The process has now been under investigation for six years (1960-66) and during that period work has progressed from bench-scale laboratory tests through small-scale pilot-plant work to a 500-tpd commercial pilot unit. Test work has been carried out mainly on the ores of the Zambian Copperbelt and results have been encouraging. Recoveries on the order of 90% have been obtained on all Copperbelt ores tested with high concentrate grades. PRELIMINARY INVESTIGATION Laboratory scale segregation test work on Nchanga banded sandstone ore and oxidized ore from Kansan-shi was originally conducted by Professor Maurice Rey. SociCtC Miniere et Mktallurgique de Pefiarroya, in 1957. Both ores responded favorably to the process. In November, 1960, the consulting engineers of Anglo American Corp. of South Africa, Ltd., initiated preliminary investigations on the application of the segregation process to Copperbelt ores. In early laboratory work, samples were heated in a closed, externally heated tube furnace for one hour at temperatures ranging from 800 to 830°C. The free moisture content of the ore feed was 4% and reagent additions were 0.5% salt and 1.0% coal. Both salt and coal were pre-crushed to -48 mesh Tyler.* All samples except an ore from the Bancroft mine responded well to the process and recoveries of over 90% were obtained. The presence of dolomite was responsible for the relatively poor recoveries from the Bancroft ore, as tests on one of the other ores with additions of calcite or dolomite confirmed. Recoveries dropped from 94 to 45% Grades of all the rougher flotation concentrates produced were low at 10-15% copper. The laboratory investigation was then followed up on a pilot-plant scale. An attempt was made to carry out the segregation process in a coal-fired 5-ft-diam fluidized-bed roaster. The feed consisted of a banded sandstone from Nchanga to which 0.5% sodium chloride had been added. Reducing conditions were maintained in the roaster by the addition of coal in excess of that required for heating the feed. The excess coal and added salt constituted the segregation reagents and the temperature of the bed was held at approximately 750°C. Recoveries of copper and grades of concentrates were low. The reasons for lack of success were: (1) The reaction is a gaseous one and a fluidized-bed roaster is therefore unsuitable as a segregation unit. (2) Coal in excess of that required for heating was introduced into the fluidized bed and under these conditions some of the copper would be reduced in situ. The term "reduced in situ" is used here to describe any copper mineral reduced to the metallic state in its original site within the ore particles. If this copper is to be recovered by subsequent froth flotation it must first be liberated from the gangue by grinding or some other method which, in practice, is usually not feasible on ores of this type.

Jan 1, 1969

By C. W. Arnold, H. L. Stone, D. L. Luffel

The purpose of this research is to determine (I) the efficiency of small banks of enriched gar driven by methane in displacing oil from a porous medium and (2) the effects of variation in bank size and composition of that efficiency. Most of the experiments were conducted in a sand-packed tube 20-ft long and 1/2-in. in diameter. The hydrocarbon system generally used was methane, butane and decane at 2,500 psia and 160°F. The results of these experiments indicate that, in the regions contacted by the gas, a small bank of an oil-miscible gas driven by methane can displace all of the oil in a piston-like manner. If the enriched gas is of such composition as to remain immiscible with the oil, displacement of oil is less efficient than for the miscible case, and the gas bank travels through the sand with a velocity less than that of the driving gas. These data along with theories discussed imply that smaller banks and less total gas are required when the enriched gas and oil are miscible. INTRODUCTION Widespread application of enriched-gas drive to the recovery of oil rests upon a key factor — the use of limited quantities, or "banks", of enriched gas. At the present time, the value of liquefied petroleum gas or other enriching agents discourages their use in a continuous injection technique, or even in a large bank, except in a few isolated reservoirs. If small banks of enriched gas driven by methane were as effective in displacing oil as is continuous injection, the enriched-gas drive process might be applied to a larger number of reservoirs. Previous research on the mechanics of the enriched-gas drive process reported by Stone and Crurnpl and by Kehn, Pyndus and Gaskell has utilized continuous injection of enriched gas. This work has shown that two types of displacements occur. With gases containing sufficient intermediates. the oil is displaced misciblv and complete recovery is obtained from the regions swept. When gases are used which contain insufficient intermediate hydrocarbon for miscible displacement, oil is displaced immiscibly. In the latter type, selective solution of the intermediate hydrocarbons causes a swelling and reduction in viscosity of the oil and leads to an increased recovery over that obtained by dry-gas (methane) drive. The size of the enriched-gas bank necessary for efficient displacement of oil is determined by those factors which cause deterioration of the bank. A differentiation may be made between those factors which operate on a microscopic scale and those which act on a macroscopic scale. On the smaller scale, the enriched gas mixes in the direction of flow by diffusion and convection with the fluids immediately preceding and following it. On the larger scale, the gas may by-pass the oil by flowing through permeable streaks, by overriding the oil because of density difference, or by fingering because of unfavorable viscosity ratios. In such cases, the enriching material tends to mix with the oil both laterally and in the direction of flow. The increase in effective area available for diffusion and dispersion of the enriching components leads to a faster degradation of the bank and a need for a larger bank than is necessary for those cases in which no by-passing occurs. The effects of such macroscopic factors in the deterioration of enriched-gas banks have been reported in a separate paper by Blackwell, Terry and Rayne. The present study was confined to the factors which operate on the smaller scale, in particular to the behavior of banks of enriched gas in sands uniformly swept by the gas. Experiments were designed to answer the following questions. 1. Can small banks of enriched gas driven by methane be used to secure oil recoveries comparable to those obtained by continuous injection of enriched gas? 2. What is the optimum bank size (the minimum bank size necessary to obtain a recovery comparable to that obtained by continuous injection of the same enriched gas)? 3. How many total pore volumes of gas must be injected to obtain the maximum recovery when the optimum bank size is used? 4. What is the effect of varying the number of enriching components in a gas bank? This report describes the experimental investigations and discusses the results in terms of their significance to reservoir behavior.

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By W. A. Backofen, D. H. Avery, G. A. Miller

An evaluation has been made of the relative importance of yield strength (?) and stacking-fault energy (y) to the rate of fatigue-crack growth in materials of fcc structure. Pure copper and its solid-solution al-loys with aluminum and nickel were chosen for the study because they provided sufficient range in both quantities of interest that either could be varied independently of the other. Experiments involved alternating tension and compression of flat specimens which were prepared with sharpened internal notches so that most, if not all, of the crack-nucleation interval could be eliminated. Growth rate (dC/dN) was concluded to be proportional to the square of the plastic-strain amplitude (€,,) over a strain range of approximately 6x 10-4 to 6 x 10-3. The factor, k, linking dC/dN and ep in dC/dN = kEp2 increased and decreased with corresponding variations in y, but it did not respond syste?>/atically to change in ay, indicating that y is the significant variable in crack growth at constant plastic-strain amplitude. In polycrystalline material, k varied by a factor of 5 over the available range of y. In a few single-crystal experiments on Cu-A1 alloys the growth rate responded less strongly to change in y. It has been suggested that single crystals behave somewhat differently than poly crystalline material because there is more extetnsive substructure near the grain boundaries in the latter, and this facilitates crack advance by separation along subgrain boundaries. A point of some controversy in current work on fatigue relates to the effects of strength and stacking-fault energy on crack growth. In recent experiments a separation was made between the cycling intervals for crack nucleation and the subsequent growth that eventually ends a specimen's fatigue life.' The study was carried out on Cu-A1 alloys primarily, fatigued in alternating four-point bending to constant deflection. A nucleation interval of about 10' cycles (at a total strain amplitude = 0.2 pct) was found to be insensitive to aluminum content in the range 0 to 7.5 wt pct, while the growth period was increased approximately forty fold over the same compositional range. The increase was not in any sense linear, however. Rather, most of the change occurred below 4 pct A1 or a stacking-fault energy, ?, of about 15 ergs per sq cm. It was argued that the plastic-strain amplitude was approximately constant, and therefore the effect of composition must have grown out of the reduction in stacking-fault energy. Several studies have shown that, with high ?, cross slip is encouraged, subgrain structure is introduced during fatigue, and cracking is aided through propagation along subgrain boundaries.1-5 Therefore, lowering ? sufficiently to interfere with substructure formation would be expected to retard growth rate. On the other hand, it is a general rule that resistance to fatigue cracking increases as strength is raised. Accordingly, there might still have been some doubt that Y was the controlling variable, since strength would be increased as y was lowered by the aluminum additions. To help in dispelling that doubt, an experiment was made on a polycrystalline Cu-Ni alloy similar in strength to the Cu-A1 alloys but of higher ?; the crack-growth interval was found to be essentially that of pure copper.' Further support for this position on stacking-fault energy as it relates to crack growth is derived from work by Boettner and McEvily,6 in which the actual crack-growth rate was measured on samples previously notched so as to minimize the nucleation period. Unfortunately, it was necessary in isolating strength level to compare different alloy systems and grain sizes. Recognizing the complication, it was still concluded that growth may be retarded by a reduction in y, per se. A related study has also been made by Roberson and Grosskreutz.7 The zinc content of a brass was systematically changed to alter strength and stack-ing-fault energy, although not below the 15 ergs per sq cm at which pronounced change in growth interval was found in the earlier work. The results were limited to more or less conventional S-N diagrams so that nucleation and growth events could not be separated. No definite conclusions were drawn, but

Jan 1, 1967

By K. L. Komarek, P. F. J. Landler

Synthetic polycrystals of wustite were reduced ilz H2-H2O mixtures over limited roncentration ranges wiltun the wustite. field and the weight changes were continuously followed with a McBain quartz spiral balance. The reduction was. found to be controlled by a combined surface plus solid-state diffusion reaction. The solid-state diffusion had an activation energy of 38 kcal. Self--diflusioities of iron decreased with itzcreasing vacancy concentration. The activation energy of. the surface reaction runs different tor- different samples. The surface reaction-rate constan increased with increasirzg vacancy concentration. THE reduction of the oxides of iron has been studied for many years. Edstroem' has summarized the early work and has provided much information on the reduction of magnetite and hematite by hydrogen and carbon monoxide. More recent summaries are those by smeltzer2 and Themelis and Gauvin.3 Most investigators have reported that the iron metal which forms the outer layer during gaseous reduction is rather porous. According to Kohl and Engel14 the formation of such a porous iron layer depends on the properties of the underlying wiistite layer, on the reaction of the gas with the wustite surface, and on the transport of matter through the wustite layer. McKewan, Quets, Wadsworth, and Lewis, and Knacke 10 have found that, if a porous iron layer is formed, a surface reaction between gas and wustite at the bottom of the pores controls the rate of reaction. Seth and ROSS 11 and Warner 12 have pointed out that the influence of the gaseous pore diffusion through the porous iron layer cannot be neglected. It has further been shown that the wiistite layer formed during reduction is dense and that transport of matter across the layer occurs only by solid-state diffusion of iron ions.13,14 The solid-state diffusion rates observed by Edstroem and Bitsianis 14 and the surface reaction rates observed by Quets eta1.' show that an interaction of the two steps in controlling the reaction rate has to be considered. In this investigation the reduction of wustite was studied with respect to the interaction of the two steps, isolated from any other effects, by reducing wustite within the wustite field from higher to lower oxygen concentrations with H2-H2O gas mixtures. A similar study with CO-CO2 mixtures has been performed by Levin and wagner.15 Fused synthetic wustite polycrystals were reduced in steps of 0.4 wt pct from 24.4 to 23.2 wt pct 0 and over a temperature range from 700" to 1050°C. A few tests were also conducted with reduction steps from 24.4 to 23.6 wt pct 0 and 24.5 to 23.2 wtpct0. The Fe-O phase diagram is shown in Fig. 1 where the composition of the gas phase in equilibrium with the condensed phases is plotted as pct H2 vs the temperature. A careful study of the literature led to the conclusion that the fully drawn equicomposition curves (in wt pct O) in the wustite field used by Edstroem 1,16 and other authors needed some correction. Based on results by Darken and Gurry17 (shown as open circles) and on some of our own data, four corrected curves for 23.2, 23.6, 24.0, and 24.4 wt pct O were calculated (drawn as dashed lines in Fig. 1) which should replace the fully drawn equicomposition curves. MATERIALS AND APPARATUS Materials and Specimen Preparation. Wustite was prepared from iron sulfate (Fisher Scientific Co., New York) which had a purity of over 99.92 pct, with small amounts of manganese, copper, and zinc adding up to 0.03 pct. From the aqueous solution iron oxalate was precipitated and decomposed to magnetite according to Economos. 18 The magnetite powder was pressed into cylinders and sintered in vacuum at 900°C for several hours. The sintered compacts were placed in a platinum crucible of 2.5 cm diam which was fitted into a high-purity alumina crucible and then inserted into the center of the graphite heating element of an electric resistance furnace.lg The furnace was evacuated to below 1 p Hg and the magnetite sample was slowly heated. The evolution of gases during heating deter-

Jan 1, 1967

By Ronald K. Linde

Metastable Ag-Cu solid solutions at two compositions beyond the maximum limits of solubility obtainable by quenching from the solid state were obtained by rapid quenching from the liquid state. The process of transformation of the metastable solid solutions into the equilibrium phases was studied by means of X-ray diffraction intensity measurements and electrical-resistance measurements; metallographic examination was also performed. Results are compared with those for an alloy quenched from the solid state at a composition which exists as a solid solution at elevated temperatures. Activation energies for the trans-formation were computed to be 33,600 * 2500 and 33,100 * 2000 cal per g mole for the 60.1 and 75.0 at. pct Ag;Cu compositions, respectively THE kinetics of precipitation in supersaturated solid solutions obtained by quenching from high temperature has been thoroughly studied in many alloys, and detailed investigations of the early stages of nucleation and subsequent growth of the equilibrium phases have been carried out. All of these studies have been made on alloys quenched from the solid state, however, and it is the purpose of this paper to present some of the results on the kinetics of transformation of metastable solid solutions in Ag-Cu binary alloys whose compositions lie outside of the solid-state limits of solubility. Limits of solubility in the solid state can be increased by rapid quenching from the liquid state. This was first demonstrated by Falkenhagen and Hofmann, who obtained appreciable increases in solubility limits of the elements of the first transition series in aluminum by rapid cooling of liquid alloys through contact with a copper mold maintained at liquid nitrogen temperature.' The same basic idea of cooling a liquid alloy by conduction onto a substrate rather than by convection of a gas or liquid (conventional quenching) has been recently revived and extended to very high rates of cooling by Duwez and his collaborators. The new technique was first applied to Ag-Cu alloys because the existence of a eutectic in this system is not predicted by the Hume-Rothery rules of alloy phase formation. Rapid quenching from the liquid state resulted in metastable solid solutions at all concentrations. The kinetics of decomposition of these metastable solid solutions containing 60.1 at. pct Ag;Cu (eutectic composition) and 75.0 at. pct Ag;Cu is the subject of the present paper. EXPERIMENTAL TECHNIQUES Alloys were made in 10- to 20-g heats using silver of purity 99.99 pet and copper of purity >99.999 pct. Components were weighed accurately to 0.1 mg and melted by induction heating in an alumina crucible under an atmosphere of hydrogen. Weight losses amounted to less than 0.02 ~ct in all cases. Rapid cooling from the liquid state was achieved in an apparatus of the type described by Pietrokowsky. 3 In this technique a freely falling drop of molten alloy is caught between a stationary anvil and a fast moving piston, both anvil and piston being lined with copper. The resulting foils were approximately circular (about 2 cm in diam) and from about 50 to 150 u in thickness, depending on the pressure driving the piston. Metallographic samples were prepared for polishing by edge-mounting foils in Quickmount. The mostef-fective etching procedure was found to be: 10 parts NH4OH (concentrated), 1 part H2O2 (30 pct), 5 parts H2O, swab for 5 to 10 sec. The transformation of the metastable alloys to equilibrium was followed by X-ray diffraction and electrical-resistivity measurements. The peak intensity and the integrated intensity of suitable Bragg reflections of the metastable and stable solid solutions were studied with a Norelco dif-fractometer, using nickel-filtered copper KO radiation. The peaks were step-scanned at intervals of 0.05 deg. Using either a Kelvin bridge or a null circuit with a Leeds and Northrup K-2 potentiometer, the changes in electrical resistance due to phase transformation were measured for specimens cut into strips about 20 mm long and 4 mm wide. All resistivity measurements were carried out at liquid-nitrogen temperature. The isothermal heat treatment was accomplished by sealing the samples in argon-filled aluminum containers with stainless-steel O-rings. Containers were then suspended in wax baths with temperatures in the

Jan 1, 1967

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By C. S. Simons, G. Major-Marothy, M. A. K. Grice, D. A. Dahlstrom

The vacuum filter operating variables that influence cake moisture are discussed. The influence of temperature control, particularly through application of steam to the cake, is emphasized. Results of pilot plant studies on filtration of fine hematite concentrates are presented and discussed, and are shown to support the theoretically-derived conclusions. Results on fine magnetite concentrates are also used to support the argument. The relative merits of disc and drum filters from the standpoint of cake moisture are discussed. Moisture content has always been recognized as one of the most important properties of concentrates used as pellet plant feed. Most iron ore concentrates are produced by wet methods, and are finally de-watered on filters. Obviously, a real economic advantage accrues to the ability of control the moisture content of the filter cake within the range required for optimum pellet production. Another consideration, also, has been receiving increasing attention recently. Transoceanic shippers of concentrate cargoes are critically assessing the hazards of excess moisture. The nature and magnitude of these risks have been described, ' and it appears that their elimination may require that residual moisture be somewhat lower than the limit for proper pelletization. Coarse, very free-filtering materials, such as the products of spirals, are usually best handled on top-feed types of machines. The moisture content of the cake may be held at a specified value by proper design and operation, taking into account cake thickness, air-flow rate, and drainage time. Fine-grained concentrates, with which we will be concerned here, must be filtered on Drum or Agidisc machines. With many of these materials, it is possible, by proper design, to meet cake moisture requirements with a conventional filter station. The first installations to produce high-grade pellets from magnetic taconites fell in this class. In fact, the design criteria were developed in connection with operations of Reserve Mining Co. at Silver Bay, inn.,2 and these have been verified repeatedly in other mills. The trend today, however, is toward the production of more difficultly dewatered concentrates. This is due on the one hand to the increasing attention being given to non-magnetic ores, which tend to be far slimier, and therefore much more retentive of moisture, than the magnetites. On the other hand, the pressure to improve the grade of the magnetic ores is leading to finer grinds, which also are more difficult to dewater. In the latter case, the decision to improve grade in an existing operation by finer grinding for better liberation may lead to two unattractive alternatives: 1) substantially higher bentonite consumption, plus the risk of poorer quality pellets, from high cake moisture, or 2) installation of a thermal dryer. There is, however, a third alternative. In recent papers by two of the authors3,4 it was shown that for many materials a significant decrease in cake moisture can be obtained by applying live steam to the cake face during the drying part of the filter cycle. Further, this limited drying appears to have distinct economic advantages compared to thermal drying. It is the purpose of this paper to explore the third alternative. To do this, the results of an extensive pilot study of steam filtration of a hematite flotation concentrate will be critically examined. This study was sufficiently broad so that a number of alternate suggestions (besides steaming the cake) for reducing moisture content were tested, and comparative data for both Drum and Disc filters were obtained. The work was particularly interesting since the concentrate has a high Blaine surface, and is therefore particularly difficult to dewater to the levels required. FILTER CAKE MOISTURE The significant difference between concentrate filter cake as discharged from the filter, a cargo of that same filter cake during or after shipment, and a green ball formed from that filter cake is in the relative volume of voids, or porosity. In every case, the material is a collection of small solid particles held together by the cohesive forces of a liquid. The physical properties of the aggregate are determined by the

Jan 1, 1967

By M. W. Burkart, B. Lustman

Uranium-base alloys exposed to high temperature water fail either by uniform oxidation or by sudden cracking and disintegration of the metal. The disintegration results from the oxidation of a second phase which is precipitated during the corrosion process. The precipitate has been identified as a metastable hydride of uranium. URANIUM-BASE alloys consisting of the body-centered-cubic ? phase are susceptible to two different modes of corrosion failure when exposed to high temperature water. In the first process, a smooth oxide film is formed on the metal surface which continually flakes off during exposure and results in a uniform weight loss of the specimen. The oxide is present as a thin, adherent layer whose thickness remains approximately constant. As the metal oxidizes during corrosion, a nonadherent layer is built up on this film and continually sloughs off. Coincident with the uniform corrosion just mentioned, another process occurs which eventually leads to failure of the metal by cracking and general disintegration. The failure takes place during a relatively short time compared to the total exposure. To distinguish this type of failure from the uniform corrosion, the cracking or disintegration of the metal will be referred to as discontinuous failure. For the ? phase uranium alloys it is discontinuous failure rather than uniform corrosion that limits the useful corrosion life of the alloy. This paper will be concerned primarily with the mechanism of discontinuous failure. Physical Changes During Corrosion—The alloys used in this investigation were ? phase uranium alloys containing 7 to 12 wt pet Mo or Cb. The preparation of the alloys, the method of corrosion testing, and the actual corrosion results are presented in another paper.' The ? quenching treatment consists of annealing the alloy for 24 hr at 900°C in a sealed Vycor glass tube filled with helium and then water quenching to room temperature without breaking the tube. The corrosion behavior typical of a ? phase uranium alloy is shown in Fig. 1. This specimen was a U-12 wt pet Mo alloy tested in pressurized, degassed water at 650°F. The corrosion rate was practically constant at 0.28 mg per sq cm per hr or increased slightly until about 15 to 20 days of exposure, when the onset of discontinuous failure occurred in this particular sample, and the specimen soon began to crack and disintegrate. The simultaneous increase in the observed corrosion rate is a result of the increased area of exposure due to cracking of the specimen. The microstructure of a specimen that failed by cracking is shown in Fig. 2. The presence of a plate-like precipitate can readily be seen. Metallographic examination of corrosion specimens reveals that the onset of discontinuous failure is always preceded by the formation of a plate-like second phase in the ? uranium matrix. Hydrogen analyses of specimens periodically withdrawn from corrosion test reveal that the hydrogen content of the alloy increases on exposure to the high temperature water, as shown in Fig. 3. The hydrogen is available as a corrosion product resulting from the formation of UO2 by the reaction of the alloy with water. Specimens analyzed just prior to discontinuous failure contained as much as 1200 ppm H, whereas the plate-like phase appears to precipitate out at a hydrogen concentration of between 10 and 25 ppm. The observed increase in hydrogen content prior to and during the formation of the plate-like precipitate suggests that this constituent may be a hydride of uranium. Additional evidence linking the identity of this phase to a hydride is that it can be removed by vacuum annealing at temperatures of 100°C and above. Decomposition products of the ? phase would certainly not dissolve at such temperatures, nor could other likely products of corrosion, such as oxides, be dissipated at any of the test temperatures. The precipitation and growth of the second phase during corrosion is accompanied by an increase in hardness of the specimen. The hardness increase results from the dispersion of the harder precipitated

Jan 1, 1959

By O. R. Wagner, R. O. Leach

Immiscible displacement tests were performed in a consolidated sandstone core over the interfacial tension range from less thdn 0.01 to 5 dynes/cm to better define how interfacial tension (IFTJ reduction can lead to increased oil recovery. Data obtained were displacement efficiency at breakthbrough vs IFT for both drainage and imbibition conditions. These tests simulate water flooding under oil-wet and water-wet conditions, respectively. Results of the study have shown that displacement efficiency under both oil-wet and water-wet conditions can be markedly improved by a sufficient reduction in IFT. In the particular porous media used and for the low pressure gradients employed, the IFT must be reduced to a value less than about 0.07 dynes/cm to achieve increased recovery at the time of breakthrough of the injected phase. Below 0.07 dynes /cm, further small reductions in IFT result in large increases in displacement efficiency. Observed increases in recovery were obtained at pressure gradients which are well below those which can exist in the interwell area of a reservoir under water flood. The effect of pressure gradient on recovery is discussed. INTRODUCTION A residual oil saturation remains in rock which has been water flooded because, under usual reservoir conditions, the driving force which can be generated is inadequate to expel oil trapped by capillary forces. Since these capillary forces can be reduced by reducing the IFT a frequently studied method of increasing oil recovery has been the use of surfactants to reduce the water-oil interfacial tension. Mungan l observed improved recovery in both water-wet and oil-wet systems at 1.1 dyne /cm IFT, finding that the amount of improvement was greater in oil-wet systems. Moore and Blum,2 working with visual flow cell micro-models, con- cluded that recovery cannot be improved in water-wet systems by injecting surfactant solutions. They calculated that, for a pressure gadient of 1 psi/ft in their model, the IFT must be reduced to 0.03 dynes/cm to release oil trapped under water-wet conditions. Berkeley et al.3 indicated that, at representative field flooding rates, the IFT must be reduced to 0.001 dyne/cm to improve recovery, Thus, there is a wide variation of opinion about the IFT levels needed to improve recovery under field conditions. These previous investigators all have used as their experimental method the addition of surfactants to the injected water. The use of surfactant solutions to reduce IFT creates two experimental problems: (1) the loss of surfactant through adsorption on reservoir rock can obscure the true IFT value which exists at the displacement front, and (2) at very low values of IFT emulsifica-tion of oil and water commonly occurs. It is difficult, therefore, to determine whether the increased recovery is caused by IFT reduction as such, or is instead caused by emulsification. Also the properties of the available surfactants limit the IFT range which can be studied. In the present study the purpose is to better define how interfacial tension reduction can lead to increased oil recovery. A matter of great interest is the amount of recovery improvement potentially achievable in this way. The study was made using very low pressure gradients which was well within the range achievable by water flooding in the interwell region of petroleum reservoirs. A unique experimental approach was chosen to avoid adsorption and emulsification problems, and to allow convenient control of IFT. The fluid phases used were the equilibrium vapor and liquid phases of the methane-n-pentane system. The interfacial tension level was varied by changing the equilibrium pressure of the methane-pentane system over the range from 1,200 psia to near the critical pressure (2,420 psia). All tests were performed at a controlled temperature of 100F. The IFT-vs-pressure relationship for the methane-pentane system was based on the data of Stegemeier and Hough,6 and on new data obtained in this study. With this experimental approach it has been possible to study displacement at lower values of IFT than have been previously investigated.

Jan 1, 1967

By L. D. Lash, J. R. Ross

Discovery of scandium in the Vitro solvent extraction plant for uranium led to commercial recovery of the byproduct. Micro amounts of scandium were extracted with uranium by dodecyl phosphoric acid, but failed to follow ura-niuminto the hydrochloric acid strip solution and were eventually concentrated in the organic extractant. A fluoride strip system was developed to recover scandium from the solvent in concentrated form. High purity scandium oxide was then prepared in multi-pound lots by chemical separation techniques. The plant recovery operation, final product purification, and analytical procedures are described. Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per Ib which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth's crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the U. S. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold. Chemically, scandium is in group 3A of the periodic table. It is closely associated with yttrium and the rare earths which it strongly resembles in its reactions. It has a valence of three and will form an insoluble hydroxide, fluoride, or oxalate under proper conditions, similar to the rare earths. Eight years before its discovery, scandium was predicted by Mendeleef who ascribed his eka-boron with properties nearly identical to the actual properties of scandium. Its position as the element with Atomic No. 21 and Atomic Weight 44.96 places it between calcium and titanium in Period 4 of the chart. The successful commercial application of scandium must depend on unique properties to justify use of this high cost substance. Greater consumption would allow additional price reductions, but scan- dium will remain a relatively high-priced commodity because of its inherent scarcity. Research reportedly has been oriented toward use of scandium as an agent to achieve high-temperature, low-density alloys with magnesium and tantalum.' Also, the U.S. Air Force sponsored a project for production of research amounts of pure scandium metal.' The oxide has been used experimentally in electronics, ceramics, and metallurgy. The various aspects of scandium are well covered in recent publications.s-5 CONCENTRATE RECOVERY Small amounts of scandium exist in uranium ores and are dissolved during an acid leach yielding up to 0.001 gpl Sc2O9. When Vitro converted their uranium plant from phosphate precipitation to solvent extraction: scandium was found to follow the uranium into the dodecyl phosphoric acid solvent (DDPA). However, scandium did not strip with uranium from the DDPA in hydrochloric acid, but remained in the solvent. Therefore, a concentration of scandium built up in the organic phase. Residues from the solvent were spectrographed by the U.S. Bureau of Mines and found to contain scandium. As a result of this discovery, provisions were made in the plant for recovery of scandium-bearing concentrates. Solvent extraction of uranium was added to a conventional acid leach process in a typical installation? The ore was crushed and ground, and then leached with dilute sulfuric acid. Addition of an oxidant such as sodium chlorate insured conversion of uranium minerals to a soluble form. At this point, the slurry was chemically reduced by a sulfide, such as sodium hydrosulfide, to remove substances such as ferric iron and molybdenum which were partially extracted by the solvent. The solids-liquid separation was accomplished by a four-stage counter cur rent decantation (CCD) thickener circuit. The uranium was extracted from pregnant liquor with 0.1M DDPA in kerosene and stripped with ION

Jan 1, 1961

By Pradeep K. Rohatgi, Clyde M. Adams

Structures obtained on freezing of several hypo-and hypereutectic Al-Cu alloys over a range of solidification rates have been examined. Dendrite spacing, L, increases linearly with solute concentration and with the square root of the inverse freezing rate. The relationship for hypoeutectic alloys is: where rate of change of fraction solid with time, is freezing rate, C is solute concentration, (pct Cu)=1. Mass transport in inter dendritic liquid during solidification is analyzed; the experimental observations suggest maximum concentration differences and constitutional supercooling in the inter dendritic liquid increase with an increase in the solute concentration. The dendrite morphology changes with freezing rate and alloy composition. The dendrites of the a phase are parallel, uniformly spaced plates with slow freezing and rods with rapid freezing. Nonor-thogonal side branching has been observed in phases with cubic and tetragonal structures. Side branches in a dendrites are orthogonal with slow freezing and at 60 deg with rapid freezing. Formation of second-phase envelopes around the Primary phase is also discussed. DENDRITIC structure is characteristic of many types of phase transformation. The most extensively studied so far has been solidification of liquid solutions. chalmersl and coworkers have interpreted the formation of dendrites in terms of the breakdown of a planar interface. Most of the work done concerns itself with the development of an instability at the interface. Little theoretical work has been done quantitatively to relate the parameters of dendritic structure to mass transport in the liquid phase. A few empirical relations based on the experimental2'3 observations exist in the literature. Several workers2 including Brown and Adams1 have studied dendrite spacing in A1-Cu system as a function of solidification variables. In most cases, dendrite spacing has been found to increase linearly with the square root of some parameter proportional to the freezing time. The effect of solute concentration is not clear; some workers report the dendrite spacing increases with solute concentration4 whereas others report vice versa.''' ~ohatgi' has observed an increase in the spacing between ice dendrites with an increase in solute concentration in water. Tiller has also suggested that dendrite spacing should increase with solute concentration. In the present work dendrite spacing and morphology have been examined as a function of solute concentration and freezing rate. The freezing rate is defined as the fraction of liquid solidified per unit time, dfs/dß?, where f, is the fraction solid and 8 the time. The fastest freezing rate studied was 4550 times the slowest freezing rate. THEORETICAL CONSIDERATIONS It is of interest to analyze the concentration distribution in the liquid phase between growing dendrites during solidification, Fig. 1. Since this distribution is a direct consequence of the rejection of solute by the growing solid, a diffusional process, the concentration gradients increase with the freezing rate. However, when solidification rate is the only variable in a series of experiments, the interdendritic liquid regions become smaller (i.e., the dendrites become more closely spaced) with an increase in freezing rate. The main purpose of the analytical treatment of interdendritic liquid diffusion will be to reveal a tendency for dendrite spacing to decrease with increasing solidification rate in just such a way that the maximum concentration differences developed in the liquid phase are remarkably independent of freezing rate. Two rather different analyses are set forth, one pertaining to the one-dimensional diffusion which obtains in the interdendritic liquid between parallel plate-shaped dendrites, and the other to the cylindrically symmetrical diffusion around rod-shaped dendrites during early stages of solidification. The results of the two analyses are quantitatively similar, correlating dendrite spacing, maximum concentration difference, and freezing rate. First consider the simpler one-dimensional case. Two parallel plate-shaped dendrites are separated by a distance, L, between centers, Fig. 1. Solidification takes place by the thickening of these plates, with solute being rejected into the liquid. It is assumed there is no diffusion in the solid. This thickening process is slow enough and the dendrite spacing small enough that the concentration differences which develop, although interesting and important, are very small (an important assumption which is verified ex-

Jan 1, 1968

By R. D. West

Miscible displacenzent recovers all oil in the area contacted by the injected .fluid, whereas water or immiscible gas drives usually leave substantial amounts of oil as residual. However, the Door mobility ratios associated with a gas-driven miscible displacement cause the sweep pattern efficiency to be much lower than that obtained with water flooding. One way in which the sweep eficiency in a miscible displacement process can be increased is by decreasing the mobility behind the flooding front. This can be achieved by injecting water along with the gas which drives the miscible slug. This water reduces the relative permeability to gas in this area and thus lowers the total mobility. The main operating conditions for the simultaneous injection -vrocess are that a zone of gas exists between the miscible slug and the leading edge of the water and that a su,@cient amount of gas be injected with the water to form the pas volume which is being left in the water zone. Laboratory model studies have shown that the ultimate sweep pattern efficiency can be as high as 90 per cent for a five-spot flooding system. If gar alone is used as the driving medium an ultimate sweep-out efficiency of about 60 per cent would be obtained in the same system. I INTRODUCTION The miscible displacement processes are a step towards total oil recovery. Conventional gas or water drives usually leave 25 to 5.0 per cent of the oil as residual in the swept portion of the reservoir. This residual can be eliminated if the oil is driven by a fluid with which it is miscible. At some reservoir conditions natural gas will become miscible with the oil. This is the "high pressure gas process".' More often, the oil does not contain enough light hydrocarbons to cause the gas to become miscible with the oil at reasonable pressures. In these cases a small band of fluid which is miscible both with the oil and gas must be kept between them2. Less than 2 per cent of the reservoir volume of the slug material is needed to keep the displacement miscible. Both processes work in the same manner, recovering all of the oil in the portion of the reservoir contacted by the injected fluids. The only difference is the manner in which the miscibility between the oil and the injected gas is obtained. Previous publications have contained detailed descriptions of these processes.1,2,3,4 However, total displacement of the oil in the swept region does not guarantee an efficient recovery process. The amount of oil to be recovered is also determined by the fraction of the reservoir contacted by the flood. This fraction is largely determined by the mobilities of the fluids. (The fluid mobility is the permeability of the rock to that fluid divided by the fluid's viscosity, k/p). This. dependence of the fraction swept on the mobility ratio has been shown in previous studies. Fig. 1 shows the ultimate fraction swept in a five-spot system as a function of the mobility ratio. The small drawings show the location of the areas left unswept for two different mobility ratios. The ultimate fraction of the reservoir swept is here considered to be attained when the producing stream contains less than 5 per cent oil at reservoir conditions. THE GAS-DRIVEN MISCIBLE DISPLACEMENT Since there is no oil left in the swept region after miscible displacement the mobility in this region is very high. It is often 50 times the mobility in the unswept regions. This means that the fraction of the reservoir contacted by the injected fluid will be less for a gas-driven miscible displacement than for a conventional water or gas drive. For a five-spot injection system, water would contact the entire reservoir volume, and the low pressure gas would contact about 90 per cent of this volume, while a gas-driven miscible displacement would only contact about 65 per cent of the reservoir. This poor sweep efficiency often offsets the benefits obtained through miscible displacement. Fig. 2 shows what the recovery curves for the three processes might look like for a five-spot system. The curves show the fraction of the in-place oil recovered as a function of reser-

By Robert E. Green, Robert A. Swanson

Ultrasonic attenuation and stress were measured simultaneously as a function of strain for aluminum single crystals tested in compression. The propagation mode and polarization of the ultrasonic waves were chosen with reference to the theoretical analysis presented in Part I. Good experimental agreement was found with this theory and with earlier experimental work in tensile tests. Support is given to the contention that ultrasonic -attenuation measurements are much more sensitive to the early stages of plastic deformation than are conventional stress -strain measurements. Dislocation meclzanisms are suggested which are compatible with both the present and the earlier experimental observations. A brief historical introduction of previous work concerned with the study of dislocation motion by ultrasonic-attenuation measurements has been given in Part I. The purpose of the present experimental investigation was to make use of the theoretical considerations from Part I in order to gain further knowledge concerning dislocation motions during plastic deformation. Emphasis was placed on the choice of propagation modes and polarization of the waves, such that interactions between these waves and dislocation movement on a specific slip system could be investigated. EXPERIMENTAL PROCEDURE Since the primary concern of this investigation was dislocation damping, other sources of damping were eliminated as much as possible. The test specimens were 0.5-in.-diam single crystals of 99.99+ pct pure aluminum grown from the melt by a modified Bridgman technique. Ultrasonic-attenuation measurements were made at a frequency of 10 megacycles per sec using a Style 56A001 Ultrasonic Attenuation Comparator manufactured by Sperry Products Inc. after a design by Chick, An- derson, and Truell.1 At this frequency the particle vibrations are essentially adiabatic and thermo-elastic damping should be absent. This frequency was selected since it was one of the frequencies used by Hikata et al.2 n conjunction with tensile tests on aluminum crystals, thus allowing direct comparison with this work. The use of quartz-crystal transducers insures that the amplitude of vibration is not sufficient to cause the break away of the dislocation loops from weak pinning points. The quartz-crystal transducers used all possessed a resonance frequency of 10 megacycles per sec and were thin circular discs 0.375 in. in diameter. X-cut crystals were used to generate the longitudinal waves and AC-cut crystals to generate the transverse waves. Aluminum was chosen as the basic material because it is a typical fcc metal whose deformation behavior is well-known and because the most recent work at the time the present research was initiated was that by Hikata et al. who used aluminum. The present tests were run in compression to see if such tests could be satisfactorily run in compression without being severely masked by grip effects.. A second reason was to compare the results in compression with those of the tension experiments of Hikata et at. Finally, shorter specimens could be run in compression with less over-all damping than in tension. All of the aluminum-crystal test specimens used were oriented for plastic deformation by single slip; i.e., they possessed the orientation having a maximum Schmid factor of 0.5. Because of the well-known time dependence 3 of plastic strain at constant stress, the test specimens were subjected to a quasi-static loading. Previous investigations4-' have indicated that attenuation after plastic deformation is also time-dependent, so any continuous loading of the specimen would show that changes in attenuation were also a function of strain rate. By loading the specimen to a given stress level and holding it constant until the recovery process was essentially complete, the time dependence was eliminated. The quartz transducer was permanently bonded to the aluminum crystal using Eastman 910 cement. Excess cement was removed from around the quartz with DMF (dimethyl formamide). Eastman 910 was found to be far superior for bonding, especially with regard to the shear-wave transducer, since it formed a solid bond which readily supports shear-wave propagation. The solid bond formed by the Eastman 910 cement also insured that the quartz

Jan 1, 1964

By A. S. Odeh

This paper analyzes the effect of limited entry to flow at the wellbore on the steady-state productivity of a well. Wells that have been opened to flow along a fraction of their productive interval are termed wells with limited entry. Previous work treated the cases of a partially penetrating well, a well producing from the central portion of the productive interval and a well in which several intervals equally spaced were open to flow. In this paper the open interval can be located anywhere within the productive interval. Thus, in a sense, it generalizes previous work. The finite cosine transform was used to arrive at a solution for steady-state flow of a slightly compressible fluid. The solution was programmed for a CDC 1604 computer. Numerical vaIues for rd = 660 ft, r, = 1/4 ft, and range of sand thickness of 20 to 200 ft are presented in graphical form. The effect of rd and r, values on the result is shown in a table. The correct calculation of skin and damage ratio in the presence of limited entry to flow is explained and illustrated by examples. Moreover, the paper shows how to calculate the net decrease in productivity due to the combined effect of limited entry and perforations. INTRODUCTION In some wells only a fraction of the productive interval is open to flow. Location of this fraction is usually dictated by formation characteristics and reservoir behavior. For instance, if a gas cap exists, the open interval is located away from the gas-oil contact to prevent any possible gas coning. Wells that intentionally have been opened to flow along a fraction of their productive formation are tened wells with limited entry. Obviously, unintentional completions of this type also exist. Limited entry to flow decreases well productivity. Magnitude of the loss depends on the fraction of the formation open to flow, on the thickness of the sand, on the location of the open interval and on the ratio of rd /r, where r , is well radius and rd is the drainage radius of the well. The use of pressure buildup data on producing wells to calculate the condition of the formation around the wellbore is an accepted practice. van Everdingenl and Hurst2 introduced the concept of she skin factor s considered to be due to a thin layer of different permeability immediately around the wellbore. These authors dealt with the case of a well of complete radial geometry, i.e., a well with open-hole completion that completely penetrates the formation. The presence of a low-permeability skin results in a loss of productivity, as does limited entry. Therefore, if pressure buildup data obtained on a well with limited entry are used to establish the presence or absence of skin (i.e., formation damage), and a correction is not made for this loss of productivity, the calculations would result in an erroneous skin value. They might indicate the presence of formation damage when in reality there is none, or they might indicate a value larger than the true value. This could lead to an incorrect basis for planning remedial measures. Muskat3 studied the problem of partially penetrating wells for the case of incompressible flow. He presented equations and figures which allow estimation of loss in productivity. Brons and Marting,4 using equations based on Nisle's work,5 studied the loss of productivity for three cases. The first was for a partially penetrating well; the second was for a well producing from only the central portion of a productive interval; and the third was for a well in which several intervals equally spaced were open to flow. Their work was for steady-state depletion-type reservoirs wherein the well radius of drainage is established and the fluid is considered to be slightly compressible. Considered in this paper is the problem of wells with limited entry in which the open intervals are located anywhere within the productive sand. The finite cosine transform is used to arrive at a

Jan 1, 1969

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world's largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson' have described the geologic setting of the mineralization. The sulfides, believed to be syngenetic, include chalcopyrite, cubanite, pentlandite, pyrrhotite, and minor amounts of bornite. They occur disseminated in the silicates and as small interstitial masses. The ratio of copper to nickel is about 3.8:1, based on 66 chemical analyses of rock samples from various outcrops (Ref. 1, p. 702, and Ref. 2). Test Procedures: With specified exceptions, all nickel and copper tests were made by the chromo-graph method,:' which measures the intensity of a colored spot formed by a reaction between the metal being determined and special reagent paper. The intensity is then compared to the intensity of spots prepared from samples of known metal content. Details of the test procedure are outlined in another article (Ref. 4, pp. 77,78). All soil samples tested in this investigation to date have been weighed on an analytical balance. However, a volumetric scoop designed to provide about 0.1 g of soil adds to the speed and ease of testing and has been found to give satisfactory results (Ref. 5, p. 531, and Ref. 19). The size of the samples used for the tests was 0.1 g. Whenever such small samples are used there is some question as to whether they are representative of the several grams in the field sample. Many repeat tests of the samples used in this investigation demonstrated that results can be reproduced within the limits of accuracy of the method without formal mixing beyond that inherent in screening the soil fractions. Furthermore, the 0.1 g is probably as representative of the field sample as the field sample is of its area of influence. Hawkes and Lakin (Ref. 6, p. 291), who considered the general problem, compared ground and quartered bulk samples of 500 g with 5-g grab samples. They concluded that "there is no significant loss in accuracy of data by substituting grab samples for bulk samples." The term soil implies somewhat different things to the geologist, engineer, and soil scientist.' For convenience the term as used in this article refers to unconsolidated material (the mantle) overlying bed rock. Sampling Procedure: Samples were taken at 100-ft intervals along north-south traverse lines across the gabbro-granite contact. The soil (till) samples were taken at an average depth of 1 ft, which was below the high-humus surface layer and into clean till. Samples taken at 1-ft intervals down to ledge showed as high a metal content at 1 ft below the air-surface as at greater depths and in two instances were slightly higher. The till at 1-ft depth did not appear to differ from material at greater depths. Total depth to bedrock has been tested at only a few points and where measured varied from 1 to 10 ft. Aerial Distribution Contours and Profiles: Plotting of copper, nickel, and cobalt content in contour form (Fig. 2) shows that anomalous amounts of these metal ions occur in till over and closely adjacent to mineralized areas of the gabbro. Contouring nickel content alone, or the copper content, outlines the same target area. Contours of the copper content provide a more distinct anomaly than nickel because of the higher copper concentration. The traverses are rather widely spread for interpolation; however, drilling has confirmed the target area essentially as shown.

Jan 1, 1959

By C. J. Frosch, J. A. May, H. G. White, C. D. Thurmond

Gallium phosphide epitaxial layers were grown from the vapor phase on undoped single-crystal galliurn arsenide substrates in silica tubes by an open-tube wet-hydrogen process. The epitaxial layers were grown over a range of water pressures at three substrate temperatures. Excess donor concentrations were determined by surface barvier capacitance measurelrzents without removing the layers from the substrates. The excess dmlor concentration, ND-NA, is fo~ind to vary approxilnately inversely with the pressure of water added to the hydrogen carrier gas. This is the relationship that would be expected for singly ionized silicon donors on gallium sites in extrinsic galliunz phosphide, with the silicon coming from the SiO generated by the reaction of hydrogen with the silica tube. An increase in the partial pressure of water in the hydrogen stream decreases the SiO pressure. The results indicate that ni, the intrinsic hole and electrmt concentration for gallium phosphide at the three substrate temperatures, is smaller than the concentration estimated from available data for the density of states effective masses and the energy gap. Mass-spectrographic measurements confirm that the dono?, introduced into gallium phosphide is silicon. The equilibrium concentrations of silicon in vapor-flown gallium Phosphide have been estimated from available thernzodynamic information that includes the solubility measurements of silicon in gallium phosphide in equilibrium with a gallium-rich liquid phase. Satisfactory agreement with the measured silicon concentrations is obtained. FROSCH1 has described an open-tube process for growing single-crystal Gap from the vapor phase by a GazO transport mechanism. The method depends upon the reaction of H20 in an H2 carrier gas with a heated source of polycrystalline Gap which provides the necessary vapor species. When the temperature of these vapor species is lowered, super saturation occurs and single-crystal Gap will deposit on a suitable substrate. Unintentionally doped single crystals of Gap grown by the wet H2 process in silica tubes are n type. Evidence is presented to show that the donor introduced is silicon, and that a qua si-equilibrium model accounts for the inverse dependence of the donor concentration on the water partial pressure and predicts the magnitude of the donor concentrations. Ainslie et al. experimentally showed a similar inverse relationship between the carrier density and oxygen pressure for GaAs. Emission-spectrographic analyses showed a decrease in the silicon concentration with increasing oxygen overpressure for GaAs. Cochran and Foster suggested the theoretical possibility of suppressing silicon contamination by using Ga20 generated by the reaction of gallium with water vapor. 1) EXPERIMENTAL The apparatus and procedures are essentially the same as those described by Frosch.' The apparatus consists of a 25-mm-ID SiO2 tube extending through a controlled high-temperature flat zone for the location of the polycrystalline Gap source and a downstream temperature gradient falling at a rate of about 14°C per cm. The latter provides the region of super saturation for the location of the single-crystal substrate. The partial pressure of water in the inflowing hydrogen stream, pA2, O was controlled by mixing me-tered proportions of dry H2 with H2 saturated with H2O vapor at 0°C. The total gas flows were about 200 cu cm per min in all experiments. The Gap sources were prepared by pulverizing boat-grown polycrystalline ingots to pass a 20-mesh sieve. The substrates were cut from an undoped single-crystal boat-grown GaAs ingot purchased from Monsanto. This ingot had a carrier concentration of about 1015 atoms per cu cm, a resistivity of about 5 ohm-cm, and a mobility of about 5000 sq cm per v sec at 25°C. Substrates with dimensions of 1 by 1 by 5 x lo-' cm were employed. The growth faces were chemically polished (111) arsenic faces. Epitaxial layers, at least 7.5 x 10-3 cm thick, were grown,. This required from 1 to 24 hr depending upon the Pii2Q values and the temperatures. In all of the runs, the source temperatures were 50°C higher than the substrate temperatures. Samples were prepared

Jan 1, 1968