Search Documents

By R.K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By H. Brevers, Maurice Rey

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

By J. W. Fredrickson

VERY little information is available in the literature concerning the solubility of magnesium in titanium. Aust and Pidgeon&apos; report the solubility of titanium in magnesium to be 0.0025 pct at 650°C and 0.015 pct at 850°C. X-ray diffraction studies failed to detect any evidence of solid solubility. Based on the fact that the addition of titanium to magnesium increases the c/a ratio of magnesium, Busk&apos; suggested that the Mg-Ti system, like the Mg-Zr, is a peritectic. Eisenreich- eported the solubility of titanium in magnesium to be 0.003 pct at 655°C and 0.064 pct at 760°C. Removal of hydrogen from the melt increased the solubility of titanium to 0.115 pct at 800°C. Eisenreich proposes a peritectic-type diagram for the high magnesium side of the system. Recent work&apos; with Ti-Mg diffusion couples indicate that the solid solubility of titanium in magnesium is extremely small and that there is limited solid solubility of magnesium in titanium. Experimental work on the Ti-Mg system is complicated by the fact that the boiling point of magnesium is considerably below the melting point of titanium. Consequently, the usual alloying methods are impractical. Alloying was accomplished in this investigation by sheath-rolling compressed compacts." The alloys were made from titanium sponge and high purity magnesium. Chemical analysis of the sponge showed 0.04 pct Mg, <0.005 pct Al, <0.001 pct Cu, 0.05 pct Fe, 0.022 pct Mn, <0.0025 pct Ni, 0.007 pct Si, <0.005 pct V, and <0.01 pct Zn. All heat treating was conducted in a protective atmosphere by encapsulating the specimens in fused silica ampules under a partial pressure of helium. Equilibrium was achieved by holding the specimens at temperature for periods of 24 to 120 hr. The alloys were hot rolled, cold rolled, and annealed prior to solution heat treatment. Fig. 1 shows the constitutional diagram obtained for the Ti-Mg system up to 1.5 pct Mg. Oxygen was known to be present in the alloys; therefore, it is necessary to consider the alloys as ternary rather than binary and the diagram should be viewed as a plot of a section through the Ti-Mg-0 system. Other investigatorso have shown that the addition of oxy- gen to titanium stabilizes the a phase. The data presented in Fig. 1 indicate that the addition of magnesium to titanium tends to stabilize the p phase. Armour Research Foundation7 has shown that the addition of magnesium to zirconium lowers the a transus and is classified as a p stabilizer in that system. Magnesium is soluble in solid titanium to the extent of at least 1.5 pct in both the a and /3 phases. No intermetallic compounds or magnesium-rich phases were observed either by light microscopy or X-ray diffraction. However, this does not negate the possibility that such phases exist at higher alloy concentrations.

Jan 1, 1956

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948

By F. H. Wilson, E. W. Palmer

G. L. Bailey (British Non-Ferrous Metals Research Association, London, England)—I was glad to see this further work on the structure and properties of the Cu-Ni-Fe alloys of low nickel content in which we have been so interested in the United Kingdom since before the war." The authors&apos; data on the variation in solubility of iron in both 5 and 10 pct Ni alloys with temperature is based on more detailed observations than we have made but is generally in line with our own work. The difficulty in these matters is in the identification of the structures obtained. The precipitation of the second phase which we presume to be the a&apos; solid solution, richer in nickel and iron, from the a solution with which it is in equilibrium occurs in such a fine state of division that its resolution by ordinary micro-graphic methods is impossible in the early stages. We have published some electron micrographs which illustrate the effects observed more clearly but we agree with the authors when they say that dark staining characteristics when the alloys are subjected to sea-water corrosion are more sensitive in detecting the presence of the a&apos; phase than is the microscope. After taking this point into consideration, however, I confess to some difficulty in understanding Fig. 4. I can only assume that the precipitates visible at such a low magnification as 150 diam in these relatively coarse forms are produced from iron-rich areas of the initial solid solution due to inadequate homogenization. If this is so I find it difficult to accept the authors&apos; contention that such local variations in iron concentration as are capable of giving the heavy precipitates shown in Fig. 4 do not in fact materially affect the solvus surfaces of their equilibrium diagrams. I share the authors&apos; enthusiasm about the resistance to corrosion of these alloys by seawater but I am not fully in agreement with them on the vexing question of the best iron content for these alloys. In Fig. 3 of ref. 8, we give many results showing that the resistance of these alloys to impingement attack in the Jet Test increases as the iron content rises to 2 pct. With higher iron contents pitting at shielded areas is likely to occur. Admittedly the addition of 0.75 pct Fe produces a large improvement in corrosion resistance compared with a pure 90/10 Cu-Ni alloy, but the further improvement on raising the iron to 2 pct is substantial. We recommend from 1.5 to 2 pct Fe as the desirable range from the point of view of corrosion resistance. While it is true that British practice generally uses a hard tube, the corrosion resistance of the 10 pct Ni alloys has in our work been little affected by the structural condition. Although the annealed alloys blacken in seawater, this effect seems to be superficial and not to be accompanied by any real decrease in

Jan 1, 1953

By Benjamin S. Lindsey, James Norman

BARITE (BaSO4) is the most important industrial barium mineral from the standpoint of quantity consumed. In 1938 the amount was 365,000 tons. Its uses are numerous, some of the more important being in the production of pigments, as an inert filler in a wide variety of products, as a weighting material in oil-well drilling muds, in the manufacture of some kinds of glass, and in the production of barium chemicals. The barite studied in this investigation occurs as the massive variety in a shale replacement formation near Magnet Cove, Ark. It is intimately mixed with quartz and small amounts of iron oxide and residual shale. Complete liberation of barite and quartz is not obtained when the rock is ground to 100 per cent through 325mesh. The crude rock with which all test work was done assayed 85.1 per cent BaSO4, 11.11 per cent Si02, and 2.85 per cent R2O3. Its specific gravity was 4.03. It was found in the course of the investigation that the barite contained a small amount of uniformly distributed carbonaceous material, so intimately dispersed that it could not be seen with the microscope, but gave a definite gray cast to the barite concentrates. The color of the barite in polished sections of the crude rock ranged from gray to almost black, while finely ground powder was a reddish gray. The reddish hue was due to the iron oxide present. In 1939, under the supervision of Oliver C. Ralston,* the Bureau of Mines, in cooperation with the Milwhite Company, of Houston, Texas, undertook to study the flotation of barite from Magnet Cove, Ark. Flotation of several southern barite ores had already been investigated by the Bureau of Mines.1 The Magnet Cove barite was unique, however, in that it had to be ground to such an extremely small particle size for liberation. The flotation of nonmetallic minerals in the presence of a large amount of slime is usually very difficult, and when done is an innovation calling for conditions different from those under which granular material is separated. LABORATORY FLOTATION WORK Preliminary investigation showed that the flotation reagents recommended by O&apos;Meara and Coe1 for separating barite and siliceous material were suitable, but much larger quantities of reagents were required to separate such finely divided material. Moreover, it was found that careful control of the frothing was necessary. When oleic acid and sodium silicate were used a voluminous froth was observed at the beginning of a test, and toward the end there was not enough froth to effect complete recovery of barite. The addition of pine oil as a frother gave proper frothing for the duration of the test, and the substitution of coconut fatty acid (crude lauric acid) for oleic acid produced a more heavily burdened froth. Two different paper-mill fatty-acid products were tested

Jan 1, 1941

By R. K. Matheson

The Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 190 tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65°. From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. Choice of Raise A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. Time Schedule As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1943

By F. J. Fayers, S. A. Hovanessian

The one-dimensional displacement equation for a homogeneous porous medium, including the effects of gravity and capillaty forces, has been solved by a numerical method. A finite-difference scheme is developed for obtaining saturation, pressure and fractional flow profiles in waterflood recovety problems. From the numerical examples given, it is concluded that the gravitational forces have a pronounced effect on the saturation profiles and the pressure distribution curves of the system. INTRODUCTION Within the past 20 years, a number of papers have appeared in the literature dealing with the quantitative treatment of waterflood recovery problems. In their celebrated paper, Buckley and Leverett1 described a method for calculating saturation profiles when the effects of capillary pressure and gravity are excluded. Terwilliger, et al,2 included the effect of gravity in their theoretical and experimental investigation of oil recovery problems and obtained close correlation between experiment and theory. welge3 described a simplified method for obtaining the average saturation and the oil recovery from an oil reservoir. The effect of gravity can be included in this calculation. More recently (1958) Douglas, et al,4 presented a method for calculating saturation profiles which includes the effect of capillary pressure. The authors start with the one-dimensional displacement equation (which is nonlinear in the derivative) and, by a change of variable, transform this equation to a semi-linear partial differential equation. This equation is then solved by a finite-difference method on a high-speed digital computer. Fayers and Sheldon5 obtained the solution of the one-dimensional displacement equation by directly replacing the differential equation by a finite-difference equation. The effects of capillary pressure and gravity were in- cluded in their solution. Here, since the movement of the foot of the saturation front is governed by a separate equation, the elapsed time in attaining a particular saturation profile cannot be obtained. The results of these two papers indicate that the inclusion of capillary forces eliminates the triple-valued Buckley-Leverett saturation profiles. In the present paper, the one-dimensional displacement equation for a homogeneous permeable medium, including the effects of capillary and gravity forces, is solved. The method of solution resembles that described in the paper by Douglas, et al, since it involves a similar transformation of variable. However, it extends their work in that the effect of gravity is included and, in addition, pressure profiles may be calculated. Also, the functions of saturation [kro(S), krw(S) and Pc (S) ] required are entered in tabular form rather than as low-order polynomials. This simplifies data preparation and permits the use of a greater range of function types. Unlike the method of Fayers and Sheldon, the corresponding elapsed time required for the development of each saturation profile is calculated and, also, saturation profiles may be calculated after breakthrough. THEORETICAL CONSIDERATIONS The dimensionless form of the one-dimensional displacement equation for a homogeneous porous medium as obtained from Darcy&apos;s law and material balance relations can be written as follows.

By Maurice Rey, H. Brevers

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.&apos; Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

By Theron Wasson

No major oil-field discoveries were made County; the second in Marion township, in Michigan during the year 1940. Produc- Osceola County. Both are producing from tion for the year was maintained by the Stray sand at about 1350 ft. These discoveries made in 1938 and, as a result, is fields are on structures founci by core test-below the total for 1939. Several extensions ing through the glacial drift. The Six Lakes to old fields have been made, which have field, Montcalm County, discovered in helped to maintain production in the face 1934, is Michigan&apos;s largest gas-producing of rather rapid decline in the fields of the field. it has 195 wells producing from the southwestern part of the state. Important Michigan Stray sandstone and the Upper extensions were made in Overisel, Porter, Marshall sandstone. This field was devel-Sherman, and Adams fields. Important oil oped on a 40-acre spacing plan, and gas fields of the state are shown on the -map, Fig. I. WiI~dcat Drilling Michigan&apos;s production of 19,700,000 bbl. A test in sec. 29, Winterfield township, during 1940 was 3,800,000 bbl. less than Clare County, which is producing oil from the total for 1939, but about one million the Monroe of Devonian age at a depth of greater than 1938. This brings the total 3760 ft., and a well in sec. 31, Lincoln accumulated production for the state to a township, Osceola County, producing from little over 145,000,000 bbl. the Monroe at 3625 it., should be classed as wildcats that are sure to lead to further Active Oil Fields development in I94L The leading producer for the year was the At the end of the year the Gulf Refining Temple field, Clare County, where 29 new Company&apos;s deep test on the Kawkawlin wells were drilled. The Walker field, Kent structure in Monitor township, Bay County, was second, but drilled 183 new County, was preparing to drill deeper after wells in order to gain that position. In the having had a gas blowout from a depth of extension of the Overisel field in Allegan 7775 ft. This test is the most important one County, 115 new producers were drilled. drilling at the end of the year in Michigan, The Adams field, Arenac County, was for should it develop commercial produc- revived by several wells with initial production from deeper beds it will lead to deeper tions of over 1000 bbl. per day from the drilling on many well-known structures Dundee of Devonian age. that have been producing from shallower sands. Active Gas Fields Two important gas fields were discovered Exploration by Taggart Brothers during the year. The A small amount of reflection seismograph first was in Riverside township, Missaukee work was done in Clare, Osceola, and Glad-Win Counties during the year. Exploration Manuscript received at the office of the Institute March 28 1941 by shallow drilling for structural informa- tion on beds below the glacial drift con- 347

Jan 1, 1941

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division, and revised in 1939. Generally in Table 1 the unit for prescntation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and /or commercial value. As to each spacc in the tabulation, it is citller (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are detcrminable but not detcrminable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries arc not subject to precise determination. In such rases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1939

By R. G. Paterson

THE usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired size and shape, and in one method&apos; a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averaging a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer&apos;s knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. METHOD The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or diamagnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. DESCRIPTION OF APPARATUS Of many alternating-current bridge methods applicable,3 the one shown in Fig. I (Owen&apos;s bridge&apos;) was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by P1L1. It is connected to the bridge by about

Jan 1, 1941

By T. F. McCormick

THIS year, 1950, is the golden anniversary of the construction and operation in this country of a tube mill for the sole purpose of fabricating aluminum alloy tubing. For a short period prior to the beginning of this mill, aluminum alloy tubing was obtained from foreign sources or produced in mills fabricating other metals. Indeed, it was a very short period because aluminum itself was a newcomer in the field of metals. The first sheet rolling mill had been in operation just eight years and a rod rolling mill for the production of wire and cable had been functioning one year. The first tube mill for aluminum was built by the Aluminum Co. of America in May 1900 and started production with four draw benches and five men, including the mill superintendent. The building itself was a lean-to attached to a sheet-rolling mill at New Kensington, Pa. The cost of equipment, including the draw benches, dies, mandrels, and other tools, was about $5000. This figure seems absurd in the present day but nevertheless it was questioned at that time whether or not such a large sum should be spent to embark on a new and uncertain venture. The initial production system for the new mill consisted of casting round hollow ingots in a tilting-type iron mold, reducing the ingots to bloom size outside the plant, and finally drawing to size on the draw benches. This method of producing aluminum alloy tubing survived just two years, as blooms of satisfactory quality were not obtained consistently. It was superseded by the cupping method in which a 24-in. diam circle cut from a rolled plate was formed into a tube bloom using first a small cupping press and then a push bench. It was stated that tubing so produced was limited to a maximum diameter of 2 3/4 in. and to wall thicknesses varying from 12 to 24 gage. However, for the first time all the operations were performed at one plant and the result was a quality product. Later larger cupping presses and push benches were obtained and the method continued to be the principal one for aluminum alloy tubing for almost a quarter of a century. During the interim the use of a Alan Mannesmann -type billet piercer was explored and it was used to some extent, but failed to produce consistently a smooth inside surface suitable for drawing with aluminum alloys. Experiments started during the latter stages of World War I in the production of tube blooms with a hydraulic extrusion press, led to the use of this type of equipment to make tube blooms for further drawing during a change-over period extending from 1925 until 1930. At this time the cupping method was discarded completely. From these humble beginnings, the aluminum alloy tubing business expanded until well over six million pounds were produced in a single month in the United States during World War II. The major portion of this production was in strong alloys which did not appear in the tubing picture until 1022, when 17S alloy tubing was introduced for aircraft construction.

Jan 1, 1951

By Y. C. Liu, R. H. Richman

Deformation and recrystallization textures of the a solid solutions of Cu-P, Cu-As, and Cu-Sb alloys are examined as a function of composition. It is found that the deformation texture of copper is unckanged up to a composition of 0.43, 0.41, and 0.24 at. pct of phosphorus, arsenic, and antimony, respectzvely, and then the transition to the 70 : 30 brass type of deformation texture proceeds linearly as the logarithm of the solute content. Recrystallization textures consist of strong, new components that do not all bear the usual<111> rotational relation to the deformation components. The dependence of the deformation texture transitions and the recrystallization orientations upon composition and solute-element type is discussed. A systematic evolution of individual recrystallization components in the annealing texture of copper was portrayed as a function of germanium or tin content in a previous study.&apos; Similar patterns of tex-tural change have been observed with copper-zinc alloys,2 and in less detailed studies of other systems.3,4 In fact, most of the literature dealing with preferred orientations in copper alloys indicates that the influence of solute elements upon textures in copper is of one general type. As the alloy content of copper is increased, the deformation texture changes from the copper type to the 70:30 brass type, and the annealing texture undergoes a comparable change from the (001) [ loo] orientation of unalloyed copper to the {113} <211> type of 70:30 brass, with the notable exception of copper alloyed with Periodic Subgroup V-B elements.4-8 In almost every case it is possible to describe the reorientations after annealing as 30 to 40 deg rotations about <1ll> poles of the deformation components. Since there is apparently not much difference in the final textures of the copper binary systems already investigated, only a limited variety of preferred orientations has served as the basis for current theories of the origin of annealing textures. In order to test the validity of the proposed theories, and the possibility that the <111> rotations are not unique, it would be most desirable to study the reorientation relationships of additional, and heretofore unanalyzed, recrystallization components if such components exist. Examination of the literature reveals a good deal of uncertainty concerning preferred orientations in copper alloyed with elements in Subgroup V-B of the Periodic Table. Phosphorus is known to inhibit the cube texture in copper when present in amounts as low as 0.01 wt pct,8 but the recrystallized matrix that occurs instead of the cube orientation was reported as either random or weakly textured, with orientations not observed in Cu-Zn, Cu-Ge, or Cu-Sn alloys.4-9 A Cu-0.75 at. pct As alloy apparently contained, along with the (001)[100] and (113) <211> type of recrystallization components, {110} <112> and (110) <001> components, whereas an almost random distribution of orientations was found in alloys of higher arsenic content.4 A {110} <001> component also appeared in rolledand annealed Cu-Sb alloys, but otherwise the recrystallization textures of Cu-Sb alloys seem to con-

Jan 1, 1962

By Arnulf Muan, Klaus Schwerdtfeger, L. S. Darken

The equilibrium ratios CO/CO, of. a gas pharse coexislitrg with selected oxide phase assemblages of the system "FeO"-MnO-SiO2 and metallic iron have been determined at 1150°C. The data obtained are combined wilh the thermodynamic data on fayalite (Fe2SiOi) and "FeO"-MnO solid solutions to derive the actiuity-coiHpQsiUon relations for the various oxide components of the olivine (Fe2SiO4-,lIn2Si04) and pyroxenoid (standard free energies of formation of ferrosilile (FeSiO,), tephroite , and rhodonite from their oxides have been evaluated. In the Appendicc~s by Darken and Schivcerdtjeger the ideal solution law for solid deri oed. THE quaternary system Fe-Mn-Si-0 is of interest in many important phases of iron- and steelmaking. For instance, reduction in the blast furnace of ores containing Fe-Mn silicates, deoxidation of liquid steel with Mn-Si alloys, formation and subsequent alterations of oxide inclusions in steels, and the oxidation of manganese- and silicon-containing steels during processing are all governed largely by the thermodynamic relations existing in the system Fe-Mn-Si-O. Although the equilibria between liquid iron and Fe-Mn silicates have been studied in detail previously,&apos; experimental data are lacking for equilibria among the solid phases. The present paper provides such data for a selected temperature, 1150°C. I) PREVIOUS WORK The general feature of subsolidus phase relations in the system iron oxide-manganese oxide-silica under strongly reducing conditions is known.&apos; Fig. 1 represents an isothermal section at 1150°C. The phases present, in addition to silica, are three solid-solution series, viz.. the oxide solid-solution series "Fe0"-MnO (manganowiistite), the orthosilicate solid-solution series Fe2SiO4-Mn2SiO4 (olivine), and the metasilicate solid-solution series FeSi03-MnSi03 (pyroxenoid). The "FeO"-MnO solid solution is continuous between the two end members wustite and manganositeV3 as is the orthosilicate series between the two end members Fe2SiO4 and Mn2 SiO4. 4 The metasilicate solid solution, on the other hand, extends only part way from the MnSi0.l end member toward FeSiO because the latter end member is unstable relative to the phase assemblage fayalite + silica. The letters a through m in Fig. 1 identify end members of the individual solid phases dealt with [for instance, c designates fayalite (FeZSiO4) in equilibrium with wustite, e designates fayalite in equilibrium with silica, and so forth]. In addition to the phase relations there are some thermodynamic data available for the end members of the silicate solid solutions and for the "FeO" -MnO solid solution. The free energy of formation of fayalite (Fe2Si04) from its oxide components has been studied by several investigators. Unfortunately, the data obtained show considerable discrepancies. According to recent tabulations by Kelley, the change in standard free energy Affn for the reaction

Jan 1, 1967

By J. E. Pavlick, A. G. Guy

The total creep of tin alloys containing antimony in solid solution was observed to decrease with increase in antimony content. However, near the solubility limit an anomalous maximum in deformation was. found, in agreement with similiar observations by Bochvar. IT has long been recognized that alloys may deform more rapidly under stress if there is a tendency for a phase change or other structural change to occur simultaneously. However, the phenomena involved are complex and in some instances the opposite effect, strengthening, may result.&apos; This area of research has not attracted much interest in the western world, and although Russian investigators have studied it for the past 15 years their work has not received due attention here. Recently diametrically opposing views on one aspect of this problem have been espoused by two Russian investigators, Kornilov and Bochvar. The question is this: in certain binary alloys tested in creep at the temperature where the solute is at the limit of solid solubility, does the incipient formation of the second phase strengthen or weaken the alloy? Korni-lov&apos;s arguments in favor of strengthening were presented at the 1954 Symposium at the National Physical Laboratory, =Creep and Fracture of Metals at High Temperatures.The most recent statement of Boch-var&apos;s theory of weakening is in Oding&apos;s new book on creep and rupture.3 Although Bochvar agrees that strengthening occurs in some alloy systems, he argues that in certain alloys an anomalous weakening is observed. However, the extensive work of Korni-lov&apos;s group on creep properties of alloy systems has not revealed any anomaly of this type, but instead has tended to refute Bochvar&apos;s theory. This clear-cut controversy offered a good opportunity for a simple experiment to resolve the problem. The experiment and its results supporting Bochvar are the subject of this paper. However, it will be helpful first to sketch the present status of the larger question of the effect of a phase change or other structural change on plastic deformation. PREVIOUS WORK One of the first researches in this area was by Pfei1,37 who investigated the creep resistance of an 80 Ni-20 Cr alloy containing varying amounts of titanium. He found that the resistance to creep increased rapidly as the solid solubility limit in the alloy at 775&apos;c was approached and slightly exceeded. With further addition of titanium the creep resistance decreased, presumably because of precipitation effects. Bochvar&apos;s first work in this field was a study in 1945 of "superplasticity" in zinc alloys containing 15 to 25 pct Al.4 He found that alloys quenched from about 400 had anomalously low hardness when tested below this temperature. The following year, in a paper on the dependence of mechanical properties on the composition and structure of alloys,5 he extended some observations of Kurnakov to predict that at high temperatures of testing the hardness values for solid-solution alloys might be lower than those for the component metals. He also pointed out the influence of changes in solidus temperature in affecting curves of hardness vs composition, and he

Jan 1, 1962

By W. Vickers

Single-point rotating cantilever fatigue tests have been carried out at 550" to 650°C on beryllium produced by a variety of fabrication routes. All the specimens gave similar plots of stress against number of cycles to failure but failure occurred at a lower stress range in the hot-pressed material than in the extruded material. A discontinuity or "kink" appears to exist in the curves and this is considered. A true endurance limit was not evident up to 10 cycles. When Brush hot-pressed warm-extruded beryllium was tested at 600oC a relationship where Nf = number of cycles to failure, ?ep = plastic strain range, and c = constant, was shown to be applicable for values of ?ep > 6.3 x 10-4. Further for this moterial and temperature and for frequencies between 150 and 4500 cycles per min, the variation of number of cycles to failure with frequency obeyed the expression N = Af0.44 where N =number of cycles to failure, f = frequency, and A = constant. Examination of the fracture surfaces indicated that they were generally intergranular and in all cases the higher the stress the more irregular was the fracture. Microexamination has shown that grain boundary cavities and fine intergranular cracks were associated with the fractures. REVERSING or cyclic stresses set up in fuel elements can lead to failure by fatigue. Fatigue stresses may be developed by instability of the fuel element in the coolant flow leading to rattling against the channel wall or fin vibration. Thermal cycling also sets up reversing stresses due to differential expansion of fuel and can. Fatigue resistance is of some importance therefore in the evaluation of canning materials. At the time the work described in this paper was initiated, beryllium was being considered for the can and endcaps of an advanced gas-cooled reactor fuel element. With this in mind, beryllium obtained from different manufacturing routes was tested on single-point rotating cantilever fatigue machines at temperatures the same as those envisaged in the reactor to obtain appropriate fatigue data. The results obtained indicated a discontinuity in the S-N curves coinciding with the yield stress in the specimens. Although in some cases the data is insufficient to warrant a detailed quantitative analysis, a qualitative analysis of this effect was thought to be justified. 1) EXPERIMENTAL DETAILS The materials used are given in Table I together with the production route and available analyses. The specimen shape is shown in Fig. 1. The fatigue specimens were machined slightly oversize, after which they were given a stress-relieving anneal of 1 hr at &apos;750° C in vacuum. This was followed by an etch in sulfuric-phosphoric-chromic acid mixture down to the finished dimensions given in Fig. 1. Etching served to remove the interference colored oxide film formed on the surface during annealing and very small recrystallized surface grains too. The specimen was mounted in the grips of a cantilever machine and rotated inside a furnace controlled at the testing temperature. The specimen was loaded in increments as the speed was increased until the required load was applied at 5000 cycles per min. A revolution counter was used to record the total number of cycles.

Jan 1, 1964

By P. K. Koh

With identical annealing heal treatment the development of major annealed texture component seems to depend primarily upon the degree of cold reduction. Cube texture was evident on annealing- 1/2-, 1,/4- , and 1/8-mil tapes at 760°C, but it dissap-)eared on 927°C annealing of 1/8-mil tape cold reduced 96.9 pct. Some cube texturee remained as tile strongest 927 °C annealed texture component in 1/4- and 1/2-mil tapes cold reduced 93.8 and 87.5 pet, respectively. The switching coefficient increases and the squareness ratio of the hysteresis loop decreases proportionally with increasing cube pole concentration. PREVIOUS studies 1,2 on the 1/8-mil ultra-thin molybdenum permalloy tape established cold rolled and annealed textures and their magnetic performance for switch-core and coincident-current memory applications, The major cold-rolled texture was found to be of {110}<335> which is quite similar to the cold-rolled texture of silver and 70-30 cartridge brass. The major annealed texture components were found to be of {120)-- <001> and {113)<785>. Although the direction for easy magnetization for this type of alloy by the single-crystal technique is not avaliable, knowledge from related studies indicated [Ill] as the easy magnetization direction, similar to that of nickel.&apos; Therefore, a cube orientation, if present in the tape core, would be most detrimental to its magnetic performance.3 In its cold-rolled state the tape had < 111 > directions in the rolling plane 14.5 deg from the rolling direction.&apos; But the coercive force of the tape in such condition will be excessive due to large amounts of internal stresses, and therefore makes its use impossible for memory applications due to long switching time. In lower nickel alloys, suchas 50-50 nickel-iron and 65 pct Ni-Fe sheets, previous investigators4"7 found the presence of cube texture on annealing at 900° to 1000°C. Although no cube texture was found in annealed 1/8-mil tape,"&apos; its presence in some annealed 1,/4-mil tape cores was firmly established a year ago as verified by significant differences in magnetic properties. The present investigation is devoted to the orientation study and related magnetic measurements on three thicknesses of the ultra-thin tape, namely, 1/8 mil, 1/4 mil, and 1/2 mil, cold rolled directly from annealed 4-mil stock in the cold-rolled state as well as after they were annealed at 760°C (1400° F) and 927°C (1700°F). The results obtained might serve to elucidate the development of annealed texture as well as to establish clearly the importance of preferred orientation on the magnetic performance of such memory tape core despite its well-known low magnetic anisotropy exchange energy. EXPERIMENTAL PROCEDURE Samples were taken from one production heat (0.010 wt pct C, 0.004 P. 0.016 S, 0.80 Mn. 0.29 Si. 79.69 Ni. 4.42 Mo. 0.054 Co, 0.002 Ti, 0.12 Al, 0.04 Mg, 14.56 Fe). Annealed 4-mil sheets were cold re-

Jan 1, 1962

By Alfred H. Bell, Virginia Kline

In 1944, Illinois produced 77,413,000 bbl. of oil, or 4.6 per cent of the total for the United States, and continued to rank sixth in the nation in oil production. This represents a decrease of 6 per cent from 1943, when- the total Illinois production was 82,256,000 bbl. This decrease was much less than the 23 per cent decrease in 1943 from production of the previous year. The principal factor in arresting the production declinc, which had been going on since 1941, seems to be the increased drilling that followed the relaxing of the Federal Government&apos;s rules in regard to well spacing. The daily average production for 1944 was approximately 212,000 bbl. Daily averages by months were as follows: Jan......... 219,000 July........ 206,000 Feb......... 220,000 Aug......... 211,000 Mar........ 216,000 Sept......... 209,000 Apr......... 211,000 Oct......... 210,000 May........ 213,000 Nov........ 209,000 June........ 209,000 Dec......... 205,000 During the year, 1991 wells were drilled for oil and gas in Illinois as compared with 1791 in 1943, an increase of II per cent. Of the 1991 wells, 430 are classified as "wildcat" as compared with 461 in 1943. Twenty-eight new pools (Table 2 A) were discovered in 1944 as compared with 29 in 1943. Changes in federal drilling regulations, permitting closer spacing of wells, resulted in a drilling program that emphasized development of proved acreage rather than wildcatting. Data on production and drilling by fields are given in Table I; data on annual production and drilling for Illinois, in Table 3. Discoveries Twenty-eight new fields (Table 2 A), 42 extensions (Table 2 B), and 39 additional producing zones in existing fields (Table 2 C) were discovered in 16 counties in Illinois during 1944. Of the 28 new fields, one was abandoned during the year, 14 were one-well fields, eight others had not more than 6 wells, one had 8, one had 9, one had 11, one had 15, and the largest new field, Roaches North, had 28 producing wells at the end of the year. In all, 109 wells were producing in these new fields on Jan. 2, 1945, as compared with 111 wells producing from 29 new fields at the end of 1943. . The average initial production of the discovery wells of the 28 new fields was 129 bbl. of oil and II bbl. of water, a notable decline from the average initial production of 194 bbl, of oil and 15 bbl. of salt water for the 1943 discovery wells. In fields discovered since 1936, the total number of oil wells producing at the end of 1944 was 12,335. Productive Acreage The area of proved production in the new fields (discovered since 1936) increased from 144,335 acres at the end of 1943 to 173,485 acres at the end of 1944 (Table I), an increase of 29,150 acres. Of this increased area, 1720 acres are in fields discovered during 1944 and 27,430 acres are in extensions of fields discovered earlier.

Jan 1, 1945