Search Documents

By Carl F. Floe, John Chipman

THE system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100° to 1500°C., and pressures from about 20 mm. of mercury to somewhat above atmospheric. REVIEW OF PREVIOUS WORK The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as 02, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: [(MG) l 2M +G2 = 2MG K = Ma X Pa, [I]] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: [MG = Kl Pa,[2]] Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: [6Cu + SO2 = Cu2S + 2Cu20[3] K _ Cu2S X (Cu20)2 (Cu)6(Pso2)[4]] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: [8 =KI = Pte, or VSO2= K2 '~/PeO, [S]]

Jan 1, 1941

By W. S. Stahmann, F. W. Bowdish

Previously published experimental data showing that both collectable and non-collectable sulfide films may be formed on chrysocolla were analysed, and chemical mechanisms were proposed for the formation of the films. A special technique was developed by which the quantity of sulfur adsorbed was determined for samples sulfidized under different conditions of pH and soluble sulfide concentration. The data on sulfur adsorption were used together with the expression for the equilibrium constant for the proposed reaction to indicate the validity of the chemical mechanism theory. A recent paper 1 about contact angle studies on chrysocolla reported the effects of pH value and sodium sulfide concentration during sulfidization upon the character of the surfaces produced. In each experiment the surface of a specimen of chrysocolla was prepared by grinding it with fine abrasive and washing it in tap water. The specimen was then placed in the sulfidizing solution for 10 min, rinsed in tap water, treated for 15 min in a solution containing 30 mg of potassium amyl xanthate per liter, rinsed in distilled water, and tested for air adhesion in a contact angle apparatus. The results, when plotted as in Fig. 1, showed an island representing conditions giving air adherent or collectable surfaces surrounded by conditions giving non-collectable surfaces. Particular interest may be attached to the region of non-collectability to the right of and above the island in Fig. 1, and to the boundry curve separating these two regions. It is apparent that at any pH from 4.0 to 6.0, where a collectable surface may be produced, a sufficient increase in the sulfide concentration results in a non-collectable surface. Thus it appears that too much soluble sulfide has a depressing effect upon the mineral, just as it has in sulfide flotation. This paper presents some speculations regarding the chemical mechanisms by which the collectable and non-collectable sulfide films may be formed and reports on a physical-chemical study intended to support these speculations. THEORETICAL CONSIDERATIONS The experimental results presented in the previous paper were analysed in several ways in an attempt to understand better the chemical mechanisms involved. For several points on the boundary to the right of the region of contact in Fig. 1, molar concentrations of H+, OH-, HS-, and S= ions, as well as various ion concentration products, were calculated. Following the reasoning of Wark and Cox, 2,3 no single kind of ions may be credited with causing depression of the surface because none of them have a constant con-

Jan 1, 1968

By Horace Pops

Isothermal sections in the copper -rich region of the Cu-Si-Zn a1by system have been determined at 8473 760; 6003 and 482°C by means of microscopic examination with confirmatory X-ray diffraction work. The stability of the bee 0 phase decreases both with decreasing temperature and with increasing copper content. The silicon-n&apos;ch 0 phase decomposes upon quenching from high temperatures either by a martensitic or by a "massive" transformation, depending upon the solute content. A two-phase equilibrium is found to exist in the Cu-Si-Zn system between the hep < phase of the Cu-Si system and the bee ß phase of the Cu-Zn system. It is shown that the isothermal limits of the primary solid solution at 760; 6003 and 482°C are in part affected by the intermediate phases which follow them in the ternary system Possible electron-concentration and size effects upon phase boundaries are discussed. ALTHOUGH the mechanical and physical properties of silicon brasses have been measured in great detail, the factors which influence these properties are not well-understood, partly because the knowledge of the phase relationships in the Cu-Si-Zn system is limited. Gould and Ray1 studied the effects of silicon upon the hardness and structure of Cu-15 pet Zn and Cu-40 pet Zn alloys. They proposed an isothermal section at 800°C which was not based upon experimental data, since the binary phase diagrams had not been completely determined. Using Cu-Si-Zn alloys containing approximately 5 wt pet Si, vaders2 determined the boundary, at 750°C, between the copper-rich solid solution and an unidentified second phase. Masing and wallbaum3 examined a vertical section through the ternary diagram in the region between Cu-20 pet Zn and Cu-10 pet Si alloys, but they emphasized uncertainty about their data. Mima and Hasegawa4 studied the liquidus surface of Cu-Si-Zn alloys, phase transformations in high silicon-bearing (20 to 25 at. pet) alloys,5 and the phase relations in low silicon-bearing Cu-Si-Zn alloys.6 Their experiments were based upon thermal analyses and metallographic observations. The compositions of the phase boundaries were not determined with high precision, and the crystal structures of the phases were not reported. Because of uncertainties in the existing literature, it became of interest to determine more accurately the phase relations in copper-rich Cu-Si-Zn alloys. The crystal structures, stability, and phase boundaries of the primary solid solutions and several intermediate phases were determined, and the data are reported as partial isothermal sections.

Jan 1, 1964

By Harold Markus, Arthur H. Grobe, Gerhard Derge

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study. has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from 1/2 to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.? After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been damped. The pH of the electrolyte was controlled? by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.10. Potentials were measured against a saturated calomel electrode connected. to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

INTRODUCTION IT is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles.1.2,3 The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4,5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik&apos;s tests will be discussed later. Such torsion does not readily yield actual stress and strain values. Therefore a preliminary study was made of the effects of repeated direct stresses, i.e., tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluminum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension test. This alloy permitted, therefore, rather accurate control at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this investigation appear sufficiently interesting to extend the method of attack in various directions. It is intended to study (I) the effects of cycles up to a few thousands and (2) the effects of strains of different magnitude in tension and compression, respectively. The latter variable also includes as a special case the effects of compressive strains.

Jan 1, 1948

By R. W. Bowers

In order to hoist the ore according to grades, stope samples are taken. Three equidistant grooves are picked across the breast at right angles to the dip of the ore, the part removed being caught in the hand and then put into a small bag. When there is broken ore in the breast, the lines are continued down the pile and a small amount taken at intervals of the length of the sampler&apos;s pick handle. The quantity of sample from each breast will be between 2 and 3 Ib. If there are two grades of ore, bessemer and non-bessemer, there are two sets of brass checks for each chute, each check stamped with the number of the chute; one set of checks has the word "bessemer" and the other "non-bessemer." Before any ore is removed from the chutes, it is the duty of one man to see that the proper set of checks is at each chute in the mine. As each motor car is loaded, a check is attached to it. When the train reaches the shaft, the sample man removes the check on the first car, notes the grade, and directs the motorman to spot it over the proper pocket. The check is then hung on a hook with the number corresponding to the chute from which the ore came. The sample man throws a short rope with a knot in the end over the car and at the point where the knot falls a standard scoopful is taken. This is placed in a large bag that hangs directly under the hook containing the checks for that particular chute. These chute samples represent a check on the grading of the various contracts and by counting the tags a check is obtained on the miner&apos;s tally of the ore going into each chute; the total of the checks represents the hoist. During the stocking season, a standard scoopful is taken from each top tram car. This sample is taken in the same way as the chute samples at the plats underground. Top-of-car Samples These samples are taken by using a rope, preferably a clothesline, knotted each 18 in. of its length, and a hammer and a scoop. The standard scoop measures 31/2 by 21/4 by 11/4 in. and holds about 1/2 Ib. of ore. The rope, as applied to the usual railroad cars at the mine, is knotted into fifteen sections. It is placed diagonally over the car from

Jan 1, 1925

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,&apos;-&apos; but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.&apos; The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,&apos; increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 1, 1986

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8,9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation. was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, ½ in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6,9 The measure of internal friction adopted here, 1/Q, is (1/p) X the logarithmic decrement, a measure used by some writers, and is also (1/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the funda¬mental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. 1, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of l00 during the next 100° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e~H/RT [I]

Jan 1, 1942

By Vaughn Moyer

A method for incorporating well drawdown effect into reservoir calculations is presented in detail, together with examples of its use for widely divergent conditions that could be normally encountered in oil reservoir sands. Tentative conclusions as to the effect such factors as permeability, producing interval, well spacing, or well damage caused by completion or repair practice could have upon economic ultimate recovery are reached. It is carefully pointed out that the conclusions reached are subject to limitations indicated in the text, and placed upon all calculations made in the paper. Introduction Papers have been presentedl-3 in which theoretical depletion histories for reservoirs under equilibrium conditions and no appreciable well-bore drawdown pressure are determined. However, except for a limited number of cases, appreciable drawdown Pressures in a well bore exist, and Pressure and saturation gradients consequently vary throughout a reservoir. This Paper is an attempt to incorporate well-pressure drawdown into reservoir history, and to analyze certain factors, such as those involving recovery, well spacing, and productivity index, from the standpoint of permeability and drainage radius. BY incorporation of drawdown into reservoir history, it is believed that theoretical considerations will more closely approxi- mate actual reservoir behavior experienced in an oil field. For purposes of simplification, a solution gas-drive type field1 without primary gas cap, has been selected. Basic Data and Assumptions Details of equilibrium saturation conditions for no drawdown production for various pressures in a reservoir are deter-minable by methods described by several are permitting the construction of a curve of oil saturation vs Pressure for any selected combination of initial interstitial water and hydrocarbon saturation (Fig I). This curve is then a description of equilibrium saturation conditions at any given pressure in a reservoir. Developing the above, details of saturation and flow permeability may thus be determined for any increment or portion of a well drainage area or reservoir. In this manner the effect of pressure differential (drawdown) may be incorporated into reservoir and well drainage considerations. It is pointed out that this method thus makes use of no-drawdown equilibrium production data, superimposing a draw-hwn effect upon them. It also assumes that net flow conditions in any considered increment of reservoir are not materially altered by the entrance of fluids from other increments into them, but approach equilibrium for the existing pressure and saturation (i.e., each increment behaves in more or less independent fashion, dependent largely upon the equilibrium considerations mentioned above)

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1947

By Vaughn Moyer

A method for incorporating well drawdown effect into reservoir calculations is presented in detail, together with examples of its use for widely divergent conditions that could be normally encountered in oil reservoir sands. Tentative conclusions as to the effect such factors as permeability, producing interval, well spacing, or well damage caused by completion or repair practice could have upon economic ultimate recovery are reached. It is carefully pointed out that the conclusions reached are subject to limitations indicated in the text, and placed upon all calculations made in the paper. Introduction Papers have been presentedl-3 in which theoretical depletion histories for reservoirs under equilibrium conditions and no appreciable well-bore drawdown pressure are determined. However, except for a limited number of cases, appreciable drawdown Pressures in a well bore exist, and Pressure and saturation gradients consequently vary throughout a reservoir. This Paper is an attempt to incorporate well-pressure drawdown into reservoir history, and to analyze certain factors, such as those involving recovery, well spacing, and productivity index, from the standpoint of permeability and drainage radius. BY incorporation of drawdown into reservoir history, it is believed that theoretical considerations will more closely approxi- mate actual reservoir behavior experienced in an oil field. For purposes of simplification, a solution gas-drive type field1 without primary gas cap, has been selected. Basic Data and Assumptions Details of equilibrium saturation conditions for no drawdown production for various pressures in a reservoir are deter-minable by methods described by several are permitting the construction of a curve of oil saturation vs Pressure for any selected combination of initial interstitial water and hydrocarbon saturation (Fig I). This curve is then a description of equilibrium saturation conditions at any given pressure in a reservoir. Developing the above, details of saturation and flow permeability may thus be determined for any increment or portion of a well drainage area or reservoir. In this manner the effect of pressure differential (drawdown) may be incorporated into reservoir and well drainage considerations. It is pointed out that this method thus makes use of no-drawdown equilibrium production data, superimposing a draw-hwn effect upon them. It also assumes that net flow conditions in any considered increment of reservoir are not materially altered by the entrance of fluids from other increments into them, but approach equilibrium for the existing pressure and saturation (i.e., each increment behaves in more or less independent fashion, dependent largely upon the equilibrium considerations mentioned above)

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1947

By F. W. McQuiston

Idarado Mining Company&apos;s mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation I2,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. Ores The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper. lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galenn is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (I) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic inter-growth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. Plant Practice Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1949

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-The most important criterion on which judgment of the quality of manganese bronze can be based is its freedom from lead. Not over 0.03 per cent. of lead should be present in a good grade of manganese bronze. While it is not questioned that manganese bronze with a high tensile strength and considerable ductility can be made .from materials that will give a lead content of possibly 2 to 3 per cent., there is no doubt that such material, while it may machine readily, will be found to withstand the impact test very poorly, and hence be unsuited for high-grade engineering work. When lead is present in considerable amounts, it forms in small pools in the alloy and the material has little strength at these points; in fact, such spots in the metal are equivalent to nicks in a test bar as far as their effect on tensile strength is concerned. A further objection to a high lead content is the ease with which it oxidizes and its consequent tendency to produce dross. A second characteristic of a high-grade manganese bronze is a low content of manganese. This should not exceed 0.05 per cent.; in fact, very many of the best grades of manganese bronze show, on analysis, only a trace of manganese or no manganese whatever. Manganese is a deoxidizer and its ready oxidation protects the other metals of the alloy; but if it is present in large amounts it will produce considerable manganese dioxide, which does not separate readily from the molten alloy and may produce black specks or drossy spots and render the obtaining of clean castings difficult. Aluminum should be present in a good grade of manganese bronze in only very small amounts. A content of 0.10 per cent. aluminum is ample. Larger amounts have a tendency to increase the shrinkage of the alloy, to give the ingots and castings a white, scruffy appearance, and to prevent the beautiful, golden, oxidization color characteristic of high-grade manganese bronze and a most excellent indication of quality. The work that the author of the paper has done is valuable from a con- servation standpoint, and it will supplement, in a marked degree, the advances that have been made by a number of manufacturers of manganese bronze in utilizing the turnings from this material. A number of firms have succeeded in making a very good grade of ingot metal from turnings and other light scrap, obtaining a tensile strength and elongation

Jan 4, 1919

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friede1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to B00 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Emby Kaye

It is the purpose of this paper to outline briefly some of the considerations that enter into the economics of so-called recycling, the generic designation of the relatively recently developed process by which a condensate† is separated from gas-distillate gas at high pressure and the residual gas returned to the reservoir. This subject necessarily embraces not only a discussion of factors that should be considered in projecting a recycling operation, such as estimating reserves, investment and operating costs, but also a comparison of condensate with other types of petroleum. The place of condensate in its relation to the total supply of crude oil is pointed out as well as certain logical methods of product disposal. The cost of drilling wells and lease maintenance is not pertinent to this discussion because income and revenue are in this paper confined to that retained by the plant or plant operator for supplying processing facilities for the gas. Before the development of recycling a great many gas-distillate gas fields in Louisiana and Texas provided no income to their owners. When gas was sold from these reservoirs it was accompanied by irretrievable losses of condensate in the formation. The understanding of the func- tion of retrograde condensation resulted in the introduction of a new commercial petroleum recovery process for these hitherto unexploited fields and now permits the conditioning of this type of wet gas field for the sale of dry gas therefrom without waste. Some Economic Factors The study of a gas-distillate field for possible exploitation necessarily involves the critical appraisal of a number of elements, chief of which will be discussed here: (I) estimate of distillate in place, (2) estimate of distillate that can be brought to the surface, (3) available market, (4) costs. The considerations affecting the estimating of distillate reserves in place are in the main subject to the same errors as are involved in determining dry gas reserves. Determinable data including acreage, sand thickness, reservoir pressure, reservoir temperature, porosity and connate water provide the basis for calculating the volume of gas in place. Ample allowance must be made for connate water, which may occupy from 20 to 35 per cent of the pore space of the sand. The factor of supercom-pressibility is to a considerable extent nullified by the reservoir temperature. It has been considered well advised to allow this factor to serve as a cushion. With the gas reserves calculated, it remains only to assay the distillate content of the gas. Those familiar with the handling of "wet" gas at high pressure readily appreci-ate the variables in sampling gas from

Jan 1, 1942

By A. A. Collins

OF widespread interest to all lead metal¬lurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is -a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process.* OLDER METHODS Three older methods; i.e., I. Dross plus siliceous ore and limestone, 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and antimony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from 1 to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about im¬possible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it, was decided to experiment with the soda process. THE SODA PROCESS After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other suggested the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1947

By F. J. Meringer, C. W. MacGregor

Various investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-l2 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q&apos;) values mentioned above for the tension test are defined by1 S =1/A and where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. Preliminary Investigations The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 0.19 per cent; S, 0.118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Effect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

By Emby Kaye

It is the purpose of this paper to outline briefly some of the considerations that enter into the economics of so-called recycling, the generic designation of the relatively recently developed process by which a condensate† is separated from gas-distillate gas at high pressure and the residual gas returned to the reservoir. This subject necessarily embraces not only a discussion of factors that should be considered in projecting a recycling operation, such as estimating reserves, investment and operating costs, but also a comparison of condensate with other types of petroleum. The place of condensate in its relation to the total supply of crude oil is pointed out as well as certain logical methods of product disposal. The cost of drilling wells and lease maintenance is not pertinent to this discussion because income and revenue are in this paper confined to that retained by the plant or plant operator for supplying processing facilities for the gas. Before the development of recycling a great many gas-distillate gas fields in Louisiana and Texas provided no income to their owners. When gas was sold from these reservoirs it was accompanied by irretrievable losses of condensate in the formation. The understanding of the func- tion of retrograde condensation resulted in the introduction of a new commercial petroleum recovery process for these hitherto unexploited fields and now permits the conditioning of this type of wet gas field for the sale of dry gas therefrom without waste. Some Economic Factors The study of a gas-distillate field for possible exploitation necessarily involves the critical appraisal of a number of elements, chief of which will be discussed here: (I) estimate of distillate in place, (2) estimate of distillate that can be brought to the surface, (3) available market, (4) costs. The considerations affecting the estimating of distillate reserves in place are in the main subject to the same errors as are involved in determining dry gas reserves. Determinable data including acreage, sand thickness, reservoir pressure, reservoir temperature, porosity and connate water provide the basis for calculating the volume of gas in place. Ample allowance must be made for connate water, which may occupy from 20 to 35 per cent of the pore space of the sand. The factor of supercom-pressibility is to a considerable extent nullified by the reservoir temperature. It has been considered well advised to allow this factor to serve as a cushion. With the gas reserves calculated, it remains only to assay the distillate content of the gas. Those familiar with the handling of "wet" gas at high pressure readily appreci-ate the variables in sampling gas from

Jan 1, 1942