Search Documents

By James H. Pannell, John Dasher, Wilfred L. Freyberger, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By R. A. Meussner, R. J. Goode

Six intermediate phases occur in the Nb-Zn sysThese phases form by peritectic reactions at 1120°, spectively. The Nb Zn 15 phase appears as the minor phase in the eutectic structure, and the terminal phases remain nearly pure niobium and zinc even at high temperature. Vapor -pressure measurements on the four high-temperature phases (Nb Zn to Nb Zn 3) permitted estimates of the composition limits of these phases and the calculation of approximate values of AFO, AH°, and AS°. 1 HE present study of the constitution of the binary Nb-Zn system was a part of an analysis of the mechanism by which coatings of the Nb-Zn intermediate phases protect niobium against oxidation at high temperature.' Since the primary interest in these phases was in coating service, attention in this study was given principally to the four phases stable at high temperature with only cursory attention to the two low-temperature phases. The solubility studies of niobium in zinc by Martin, Knighton, and Feder2 and the reports from the present study of the Nb-Zn coating represent the only published data pertaining to this system. Previously Hodge, Evans, and Hoskins, in an experimental survey, had noted that niobium was not resistant to attack by molten zinc, but no further observations were reported. EXPERIMENTAL PROCEDURES a) General. The nature of the binary Nb-Zn system precluded the use of more conventional methods of determining the phase equilibria such as thermal analyses of a series of cast alloys. An extrapolation of the liquidus data of Martin, Knighton, and Feder2 to higher temperatures suggested that the solubility of niobium in zinc would remain low in the entire temperature range of interest. The preliminary results of the present studies showed that all of the high-temperature intermediate phases form by peritectic reactions. Thus the sluggish nature of this type of reaction and the steepness of the liquidus indicated that thermal analyses would not yield reliable data. The peritectic reactions, of course, precluded the direct formation of samples of the individual phases from the melt. b) Materials. The niobium and zinc used in the present studies were of high purity. The niobium, in the form of 0.1-in.-diameter rods, contained 30 ppm 0, 30 ppm N, and 15 ppm C. Aside from 0.05 pct Ta, the metallic impurities (iron, titanium,

Jan 1, 1965

By J. T. Berling, J. B. Conway

MANY studies have been devoted to the correlation of low-cycle fatigue behavior. Several of these have also been concerned with the identification of an effective approach to the prediction of low-cycle fatigue behavior from short-term tensile data. Perhaps the first such approach was that reported by coffin1 in the form: where is the plastic strain range, Nf is the number of cycles to failure, and c is a constant characteristic of a material. In this analysis by Coffin it was reasoned that in a short-term tensile test the value of Nf could be considered as equal to a , in which case the value of c is interpreted as the tensile ductility, f, measured in such a test. If, therefore, the Coffin equation is assumed to be applicable to a given material, it is a simple matter to predict the low-cycle fatigue behavior. Once the tensile ductility is known, this point is located at Nf = 1/4 on a log-log plot of vs Nf and a line is drawn through this point with a slope of to yield a prediction for the fatigue life. Actually, while this equation is quite useful it is not generally applicable, for experiment has shown that the value of —$ does not reflect the relationship between and Nf for all materials or even for a given material over all temperature ranges. An equation similar to the Coffin equation was prepared almost simultaneously by Manson.2 This expression had the form: In this case the exponent on Nf was not assigned any particular numerical value in accord with the various values of this exponent which had been observed for different materials and at different test conditions. Because of this characteristic it will be recognized that little use can be made of this expression in predicting low-cycle fatigue results. A fairly effective expression for use in predicting fatigue behavior was proposed by Manson3 based on a study of numerous sets of experimental results. This relation (Method of Universal Slopes) makes use of modulus of elasticity, ultimate strength, and tensile ductility, and assumes an exponent on Nf equal to 0.6 in representing the plastic strain range contribution to total strain range. While this equation of Man-Son does not yield completely accurate results it must be recognized as being the best means available at

Jan 1, 1970

By S. A. Falconer

Much attention and publicity has been given, during recent years, to grinding, classification, flotation, and thickening. The various technical papers, and symposiums held to discuss these important phases of milling, have contributed to a better understanding of the fundamental principles and operating variables involved. Another important part of milling— to the flotation operator—is a treatment step to which frequently too little attention is given—"conditioning," or the treatment the ground mineral pulp receives before it enters the flotation machines. "Conditioning" is a hackneyed and frequently misused term, commonly employed to describe the pretreatment of surfaces of minerals in ore pulps or mill products prior to froth flotation. In general, such pretreatment is for the purpose of changing the flotation characteristics of these mineral sur- faces to enable them to respond in some desired predetermined manner when subjected to flotation. Taggartl states that the function of conditioning is "either to insure selective collector coating of one mineral species while another species is not; or to take such steps as will compensate for departure therefrom." As 0. C. Ralston has stated? ... we are still faced with the fact that some mineral particles are water-avid, others air-avid, and that by properly modifying them they may be enhanced or diminished in desirable or undesirable avidity. Coatings on minerals must still be assumed to fall into three classes: (1) a coating of immiscible oil, (2) a layer of adsorbed substance, (3) a chemically produced coating. It is submitted that the process of preparing mineral surfaces for subsequent flotation treatment should take into consideration physical as well as chemical means for altering the normal flotation response of the mineral surfaces. A more descriptive word than "conditioning" is needed to designate broadly these procedures. The minerals in many ores cannot be made to respond in a normal manner to usual methods of "conditioning" with selectivity modifying reagents, until they have been cleansed, or interfering slimes and soluble salts have been removed from the ore. Therefore, it appears important to include under the general subject of "conditioning" a discussion of the purposes, methods used, and some of the advantages of these pretreatment steps. This is dealt with under the subject heading " Initial Treatment of Mineral Surfaces and Ore Pulps." Under this broader interpretation, the methods employed for treating mineral surfaces to alter their flotation characteristics may be divided into three general classes: 1. Physical methods.

Jan 1, 1950

By J. R. Cahoon, W. V. Youdelis

In a previous communication by one of us,1 a theory of inverse segregation was presented by which the maximum segregation and segregation distribution throughout a unidirectionally solidified, binary-alloy ingot could be calculated. The theory, which is based on the mechanism of volume contraction and interdendritic flow, quantitatively accounts for the observed maximum segregation in the A1 (rich)-CU' and Al-Zn2 alloy systems, and for the segregation distribution along the ingot lengths for the A1-Cu system.''4 One of the drawbacks to a more extensive use of the segregation equations is their complexity, particularly for the calculation of the segregation distribution throughout the length of the ingot, involving long tedious numerical calculations to obtain the segregation. Computer pro- grams, written in Fortran II for use on an IBM 1620 computer, have been developed by the authors (and are available from them), providing quick and accurate methods for the determination of the theoretical maximum segregation in any binary-alloy system, and also for the segregation distribution in any unidirectionally solidified binary-alloy ingot. The segregation distribution is controlled by the lengths of the various solidification zones'74 which are in turn controlled by the cooling rate, and are determined from temperature-distribution curves obtained during solidification. The theoretical segregation distributions shown in Fig. 1 illustrate the effect of the zone lengths on the distribution Curve 1, indicative of a slowly cooled ingot, represents an ingot having long solidification zones, while Curve 2, indicative of a rapidly cooled ingot, represents an ingot having relatively short zones. Although these distributions are calculated for an A1-10 pct Cu ingot, the shape of the distribution would be similar for any binary-alloy ingot. These curves show clearly why early workers obtained results which indicated that the maximum (chill-face) segregation approached zero at very fast cooling rates.3 Actually, the maximum segregation is independent of cooling rate,' but even at short distances from the chill face the amount of segregation drops considerably, particularly in a rapidly cooled ingot, making it very difficult to establish the amount of segregation occurring at the chill-face. The authors would like to thank Dr. J. A. Goldak for his assistance in the preparation of the programs. The financial assistance of the Steel Co. of Canada and of the National Research Council of Canada in the form of Scholarships to one of us (J. R. Cahoon) is gratefully acknowledged.

Jan 1, 1964

By W. C. Lacy

Urban development in semi-arid portions of the Southwest has upset a natural balance of geological conditions resulting in broad-scale and local subsidence or heaving ground conditions, Subsidence can be traced to two general causes: irrigation of reclaimed desert lands that have dry, low-density soils; and depression of the water table by ground water withdrawal. Accumulation of weathered volcanic tuff produces areas with swelling characteristics. Soil and subsidence studies made in the Tucson area in Arizona illustrate foundation problems typical of the Southwest that must be considered in the design of building codes. Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the arid to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area, prompted by foundation failures and breaking of buried service lines, serves to illustrate some of these relationships between the geological environment and history and engineering problems. ENVIRONMENT The desert region of the Southwest is characterized by isolated mountain ranges rising abruptly from low valleys or plains — the ranges generally occupy less area than do the intervening valleys. In southern Arizona the valley floors step up from near sea level to 2000 ft or more in elevation, and the ranges may rise to over 7000 ft. Desert and steppe-type climates predominate — climate is controlled more by elevation than it is by latitude. Both climate types are characterized by a lack of precipitation, the former more so than the latter. Practically all the rain that falls in the region evaporates; runoff or recharge generally occurs only during the wettest period. Water table levels are generally being depressed. Vegetation is restricted and consists mainly of creosote bush, cacti and sage brush on the deserts, and mesquite, pinon juniper and various types of grass on the steppes. Precipitation varies from about 3 in. on the warm deserts to about 12 in. on the steppes. Most of this falls in the summer or winter, with only rare storms in other seasons. Summer thunderstorms, often accompanied by hail, bring cloudbursts which send torrents of water streaming down the mountains onto

Jan 1, 1964

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

By Augustus J. Bowie

THE discovery of the auriferous cement gravel deposits in and near Deadwood Gulch, Lawrence County, Dakota Territory, in 1876, created a mining excitement, and rush to the Black Hills. Numerous ten and twenty-stamp mills were built on Deadwood Gulch ; Central City and the town of Deadwood sprang into existence, and became the centres of the mining industry of the Hills. Gold quartz deposits were subsequently discovered and located on a so-called mineral belt, extending from Whitewood Creek on the south, to Deadwood Gulch on the north. A northerly group of these quartz locations was purchased in December, 1877, by parties in San Francisco,, who formed a company, incorporated under the name of the Father de Smet Consolidated Gold Mining Company. This company immediately commenced the work of exploration. The deposits were proved to be extensive, and easily mined, but it was found that the ore, on an average, would not. yield more than $10.00 per ton* of 2000 pounds. At this time the cost of supplies and materials in the Hills was high. Miners' wages were $3.50 per diem, and custom mills charged $6:00. per ton. The successful working of mines on "the belt" necessitated cheap milling. The ores being of so low grade,† this could be accomplished only with large and economically running mills. To insure the greatest possible economy, the Father,& Smet mill * Up to December 31st, 1879; the de Smet mine had produced bullion of the value of $718,211.68 from 76,155 tons of ore, being an average value of $9.41 per ton. During the year ending December 31st, 1879, the mine produced 46,344 tons, which yielded $425,360.42, or $9.18 per ton. The total gross cost of working for the corresponding period, including deadwork, exchange, legal expenses, fete., wits $219,914.82. The yield of the mine for the year 1880 (Engineering and Mining Journal, February 5th, 1881), was $600,011, with total expenses of mining and milling, of $313,108. † The first 4083 tons extracted from the de Smet mine, were selected, yielding $62,783.97. The next 25,728 tons produced $230,067.24. The total 29,811 tons were weighed, and worked at custom mills. The yield of the first 409 tons from tine Golden Terra Mine was $11.44 per-ton.

Jan 1, 1882

By J. H. Hamilton, J. R. Lewis, J. C. Nixon, C. L. Graverson

Recently there has been much speculation concerning the advantages of using oxygen enriched air or pure oxygen in pyrometallurgical processes. The advantage of using oxygen in the iron blast furnace and elsewhere in ferrous production metallurgy has been given careful consideration and, as a result, several experiments have been tried and a number of papers have recently appeared on this subject.1,2 The use of oxygen in nonferrous smelting likewise poses interesting problems, therefore any experimental data obtained in this area should likewise be of general interest.3 Ashcroft4 in 1933 claimed to have obtained improved results when copper concentrates were roasted in pure oxygen. However, his paper gives neither data nor experimental details. A few years ago a research program was started in this laboratory which had for its objective the determination of the mechanism of oxidation of metallic sulphides under varying conditions. To date we have studied the oxidation of galena,5 sphalerite, and chalcocite. It is a well known fact that copper sul-phde minerals are oxidized slowly by weathering agents, so that the sulphides of copper which find their way into a tailing pond are gradually changed into water-soluble and acid-soluble compounds. Commercially, the oxidation of copper sulphide minerals is accomplished by roasting them at elevated temperatures in air using a suitable (usually multiple hearth) roaster. Most copper smelters are equipped with such roasters. In this phase of the study we were especially interested in determining the effect of temperature on: (I) the air oxidation of chalcocite and (2) the oxidation of chalcocite using commercial oxygen. The amount of sulphur removed as sulphur dioxide, the percentages of water-soluble copper, and of acid-soluble copper were determined for the air oxidation tests. In the tests using commercial oxygen, the percentages of sulphur dioxide, water-soluble copper, acid-soluble copper, water-soluble sulphur and acid-soluble sulphur were determined. For these experiments the temperature was varied from 250 to 700°C. Experimental Preparalion of Chalcocite (Cu2S) Natural chalcocite is not pure, Minerals such as bornite, covellite, and chalcopy-rite may be present. It was decided, therefore, to prepare some chalcocite in our own laboratory. An intimate mixture of sulphur and hool divided metallic copper in the ratio of 4 g of copper to I g of sulphur was prepared. TO this was added a slight excess of

Jan 1, 1949

By R. E. Grace

WHEN an Fe-C alloy, partially reacted to pearl-ite, is quenched rapidly enough to suddenly stop the growth process, it may be expected that any carbon concentration gradients will freeze in situ in the newly formed martensite. A short tempering treatment should precipitate finely dispersed iron carbide particles in approximately the same distribution in which carbon existed during the growth process. Examination with the electron microscope of areas of tempered martensite adjacent to the pearlite-martensite interface should reveal the existence of preferred areas of precipitation. Fig. 1 is an example of an electron micrograph used in this study. Small sections of a commercial steel (0.9 pct C, 1.6 pct Mn, 0.25 pct Si) were austenitized at 945°C in air for 45 min, furnace-cooled to 697°C, iso-thermally reacted to pearlite for 30 min, and quenched into iced brine. Two samples were tempered 5 and 20 min, respectively, in air at 498°C and were subsequently quenched in water. The samples were mechanically polished and etched in 1 pct picral. Collodion replicas were made by the conventional technique; these were shadowed with chromium at about 650' from the horizontal, and electron micrographs were taken at a linear magnification of 14,200X. Prints were made at a magnification of 44,100X. Lineal analysis of the prints was made as a function of the interlamellar spacing and volume percent of iron carbide. Straight lines were drawn into tempered martensite between adjacent lamellae at a distance S/4 or S/6 apart, where S is defined as the interlamellar spacing measured at the pearlite-martensite interface. The volume percent of iron carbide was measured along each of these traces with a "gage length" of S/10. The results of analyses of two samples are shown in Table I. The area included between the S/2 and S distance from the interface could be considered homogeneous within the sensitivity of the measuring technique. This value was used as a proportionality factor to evaluate an arbitrary carbon content of homogeneous austenite, and also as a parameter by which error in measurements could be evaluated. Results of the lineal analysis are shown in Figs. 2 and 3. Fig. 4 shows the statistical nature of the interlamellar spacing for all lamellae measured in this

Jan 1, 1954

By Luiz C. Correa da Silva, Robert F. Mehl

An experimental study of the movement of markers in the systems Cu/a-brass, Cu/Sna-solid solution, Cu/Ala-solid solution, Cu/Ni, Cu/Au, Ag/Au, employing many types of markers and a variety of temperatures. Marker movement is confirmed and undoubtedly associated with the manner in which atoms move during diffusion. EVERAL years ago Smigelskas and Kirkendall' •S reported measurements on the interdiffusion of copper and a-brass and on the movement of inert markers placed at the original join. These markers were observed to move toward the a-brass side of the join, and from this it was inferred that zinc diffuses in a-brass more rapidly than copper. Similar results were reported a little earlier for the diffusion of solvents into high polymer solids.' This has attracted much attention, particularly from those interested in the mechanism and the theory of diffusion: Seitz3 has employed it in supporting the vacancy theory of diffusion; from the data Darken4 has calculated separate diffusion coefficients for copper and zinc, developing a "phenomenological" theory of diffusion; and Bardeen5 has employed it in constructing a general theory, including therein the work of Seitz and Darken, as has Le Claire. These matters have recently been reconsidered in a sympo~ium.7 Some reason has existed for questioning the work of Smigelskas and Kirkendall.' Their technique consisted in electroplating copper on a-brass, upon the surface of which Mo-wires had been secured, and then diffusing, measuring the extent of diffusion along the normal to the join, and measuring the marker displacement in the same direction by a comparator determination of the distance between Mo-wires on opposite sides of the electroplated brass sample. It has been suspected that the copper plate might have been porous, and that the original interface might have been an imperfect join, both contributing to the transfer of the volatile zinc by vapor transfer;' it has also been questioned whether the marker movement might not in a measure be a property of the marker itself; etc. These legitimate questions require experimental answers; the present paper offers such answers. Moreover, Smigelskas and Kirkendall studied the effect only in the Cu-Zn system and at one temperature; the attention which the work of Smigelskas and Kirkendall has commanded recommends similar

Jan 1, 1952

By Jesse O. Betterton

In the Parkes process of lead refining, after desilverization has been completed by means of zinc additions, there will remain in the lead from 0.5 to 0.6 per cent zinc. At this stage in the refining practically all impurities are reduced to refined lead specifications except zinc and antimony. All excess of copper and nearly all the arsenic goes out with the silver. Silver remaining should not exceed 0.1 oz. per ton. It thus remains only to remove zinc and antimony to produce refined lead. The older practice was to complete refining by means of oxidation processes in reverberatory furnaces. Essentially this consisted of heating the lead to 1200' to 1300" I?. and allowing it to come in contact with a considerable excess of air passing through the furnace, or accomplish the same result by blowing the lead with steam by means of pipes introduced for that purpose, at the same time allowing air to enter the furnace. Usually some procedure involving alternate oxidation and reduction with fine coal or coke was employed in order to reduce the weight of dross or skim finally removed from the furnace. This practice had many elements of weakness in that the main flour of lead, after the preceding expensive operations had been performed, and the whole refining process nearly completed, was subjected to an operation at a comparatively high temperature, which involved much lead loss if the furnaces were not on bags, and the production of 3 to 5 per cent of the weight of the lead as dross or skim, which had to be resmelted and the lead either refined or produced as antimonial lead. In addition, the operating expense of the process was a considerable item. The process of dezincing with chlorine was developed as a substitute for the foregoing described oxidation process, and finally resulted in such advantages as nearly equal operating costs, a practical elimination of the lead loss, and the direct production of a very valuable byproduct, zinc chloride, that may be sold as such or retreated for its zinc and chlorine contents, both of which can be reused in the refining processes. Essentially this process consists of circulating the lead by means of a pump in a kettle through a closed reaction cylinder, gaseous chlorine entering the reaction cylinder with the stream of lead from the pump. Molten zinc chloride is thus produced and is discharged together with

Jan 1, 1937

By L. F. Stutzman, George Thodos

The friction factor plot presented by Cornell and Katz4 and developed for the flow of fluids through consolidated formations has been directly adapted for handling fluid flow problems involvitrg both linear and radial flow. In this adaptation the friction factor plot is used directly for the solution of problems and thereby eliminates the use of conventional equations which are specific to laminar (Darcy) or turbutent flow. This upproach overcomes the disadvantages inherent in the use of these conventional equations. It eliminates the necessity of checking the type of flow occurring in order to identify the specific equation which must be used. In radial flow problems, because of the increasing mass velocity of the fluids as they approach the wellbore. the type of flow may no longer remain laminar. Consequently, it is necessary to use more than one equation in a problem and to identify the range over which each equation should be applied. Finally, in practice it has been found that much of the flow of gases through consolidated media occurs in a range that is neither laminar or turbulent. For this transitional region, no convenient equations are available. The method and presented friction factor plot are appficahle to both liquids and gases. INTRODUCTION The flow of fluids through unconsolidated media in packed beds has been treated extensively by a number of investigatorsl,2,3,5,7,8 Most of these studies present friction factors as a function of modified Reynolds number similar to those developed for conventional fluid flow through pipes. These friction factor plots are presented for linear flow; however, Elenbaas and Katz have extended these concepts to apply to radial flow. All of these studies on unconsolidated materials require a knowledge of packing properties such as sphericity. porosity, and particle diameter. Sphericity and particle diameter cannot be defined at the present time for consolidated formations such as those commonly found in gas or oil reservoirs. As a result many investigators have not utilized friction factors and Reynolds number in the study of fluid flow through consolidated media. However, Cornell and Katz4 present a plot (Fig. 1) for the flow of fluids through consolidated porous media, in which the friction factor defined as: The turbulence coefficient, P, is related to the formation permeability, K, as presented in Fig. 2. Three different types of flow may exist in the flow ot

Jan 1, 1957

By Hans E. Gustafsson

INTRODUCTION The Kiirunavaara iron ore mine is situated in northern Sweden about 150 km north of the Arctic Circle. The ore body has a sheetlike shape, stretches about 4000 m N-S dipping 60°E and has an average width of 85 m. The ore body is known to a depth of more than 1500 m. Mining at present has reached a depth of about 500 m. The mineral is a magnetite containing 66-68% Fe. The ore body was originally mined as an open pit from 1900-1957. From then on the mining method has been sublevel caving. Production for the last few years has been 20-25 million tons /year. Sublevel caving is a mining method with many merits. One of the most valuable is the ability of using a high degree of mechanization. Today, 25 years after sublevel caving was introduced at Kiirunavaara, the advantages of the method have been more or less exhausted, and the disadvantages are more obvious as the rock pressure increases with depth. One of the disadvantages is the high degree of waste rock in the hoisted ore. Today the waste rock content is about 25% by weight of which 20% comes from the caved rock. Second, we are calculating a relatively high loss of ore (20%). Third, selectivity is unsatisfactory when mining different grades of ore. Field testing sublevel shrinkage caving (MSTM) is primarily aimed at lowering the content of waste rock compared to sublevel caving. ECONOMIC TARGET A simple calculation shows that if the waste rock content can be lowered from 25 to 15% the operational costs of mining will be lowered by about 40 million SEK/year (US $9 million) at a production level of 20 million tons/ year. A 15% waste content is the target of the field test. In the long range a decrease in waste rock dilution will mean lower investment costs for deeper levels. DESCRIPTION OF THE MSTM MINING METHOD One reason for decision to carry out the field test was that with MSTM the development drifts from sublevel caving could be utilized and thus the project could start without delay. The only additional development work needed was the loading level. Fig. 2 shows a profile through the MSTM area 66-68% Fe. and Fig. 3 shows the loading level.

Jan 1, 1981

By P. C. Kelly

The processes involved in turning a set of seismograph records into a geological structure map may be divided into three classes; (1) picking reflections on the records, to be used for the computations; (2) determining the basis on which the computations should be made in order to arrive at correct results; (3) making the necessary computations and plotting sections and maps. The first is usually done by the crew chief, or at least checked by him. The computing system usually originates in the head office, occasional consultations with the party chief providing modifications as necessary to meet special conditions. The computations and plotting are done by the party computer, with possibly one or two assistants if the calculations require much time. Picking the Rejleclions Marking of the reflections on the records is perhaps the most important step and the one most likely to determine the reliability of the final results. Making the "picks" is important because most of the problems that come up in practical work are connected with the problem of what can be done with poor records. The lack of any definite criteria by which to judge what are good and usable reflections is at the bottom of the difficulty. Give the same set of records to several people to mark and they will probably come out with a variation in the number of reflections per record that are deemed usable. With good records the correct picks are obvious to all, but with poor records experience seems to be the only reliable guide as to what picks are reliable and what are merely born of imagination and desperation. Experience in marking records and seeing how the structures eventually check out is more important than training in physics or geology. Different types of equipment and shooting methods may produce records quite different in appearance, from the same territory, and the computer can do his best work with records of a type on which he has had considerable experience, and has learned the limitations and shortcomings as well as the virtues of the data with which he is working. Reflections may be picked for dips only, in which case the particular reflection picked is not recognizable with certainty on records from any other spread. For the purpose of computing dips it is necessary that the reflection be marked on a11 or nearly all of the strings of the records, as

Jan 1, 1940

By P. C. Kelly

The processes involved in turning a set of seismograph records into a geological structure map may be divided into three classes; (1) picking reflections on the records, to be used for the computations; (2) determining the basis on which the computations should be made in order to arrive at correct results; (3) making the necessary computations and plotting sections and maps. The first is usually done by the crew chief, or at least checked by him. The computing system usually originates in the head office, occasional consultations with the party chief providing modifications as necessary to meet special conditions. The computations and plotting are done by the party computer, with possibly one or two assistants if the calculations require much time. Picking the Rejleclions Marking of the reflections on the records is perhaps the most important step and the one most likely to determine the reliability of the final results. Making the "picks" is important because most of the problems that come up in practical work are connected with the problem of what can be done with poor records. The lack of any definite criteria by which to judge what are good and usable reflections is at the bottom of the difficulty. Give the same set of records to several people to mark and they will probably come out with a variation in the number of reflections per record that are deemed usable. With good records the correct picks are obvious to all, but with poor records experience seems to be the only reliable guide as to what picks are reliable and what are merely born of imagination and desperation. Experience in marking records and seeing how the structures eventually check out is more important than training in physics or geology. Different types of equipment and shooting methods may produce records quite different in appearance, from the same territory, and the computer can do his best work with records of a type on which he has had considerable experience, and has learned the limitations and shortcomings as well as the virtues of the data with which he is working. Reflections may be picked for dips only, in which case the particular reflection picked is not recognizable with certainty on records from any other spread. For the purpose of computing dips it is necessary that the reflection be marked on a11 or nearly all of the strings of the records, as

Jan 1, 1940

By Noel Cunningham

Many excellent descriptions of the mills of the Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 21/2 years' mill operation in the district—i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.—There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15 of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a 1/2-in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling. In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more or less blocky at times, and with reference to Class B this is indicative of low gold content.

Jan 1, 1915

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.‡ Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; 2.3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942

By J. D. Vincent, Pierre R. Hines

INTRODUCTION OF FROTH FLOTATION INTO THE UNITED STATES "The introduction and development of the flotation process have proved to be of such momentous importance to the mining industry of the United States that they deserve to be considered historically ." T. A. Rickard l James M. Hyde installed the first froth flotation process in the U. S., about Aug. 1, 1911, at the Basin Reduction Co. plant, Basin, Mont., which was then under lease to the Butte and Superior Copper Co.2 Two months later, the Minerals Separation Ltd.. filed suit in the U. S. District Court of Montana against Mr. Hyde char& him with infringement of their Patent 835, 120/1906. The U. S. District Court decided in favor of Minerals Separation Ltd. on July 28, 1913. This decision was reversed by the Ninth Court of Appeals in San Francisco on May 4, 1914. Then the U. S. Supreme Court, on Dec. 11, 1916, upheld the patent on three counts only but restricted it to 'the use of less than one percent of oil.” The Miami Copper Co. was sued by Minerals Separation on Oct. 10, 1914, for infringement of Patents 835,120 and 962,678, and 1,099,699. The Miami Copper Co. was operating under John M. Callow's froth flotation process Patent 1,104,755/~uly 23, 1914. Miami lost this suit in the District Court of Wilmington, Del., and appealed to the Court of Appeals, Third Circuit, Philadelphia. The Third Court of Appeals decided against Miami, May 24, 1917. The case was referred to a Master and hearings to determine profit and damages were not settled until 1923. Nevada Consolidated Copper Co. was sued Sept. 9, 1919, and Magma Copper Co. was sued Jan. 10, 1920. Thus, the first ten years of froth flotation in the U. S. were beset by patent litigation. This litigation suppressed the free circulation of new discoveries or useful information that might be cited in a patent suit against the originator; it accounts for many of the blank spaces in the historical record. T. A. Rickard3 has reviewed the history of flotation and has given the chain of discoveries, patents, and processes that resulted in froth flotation. He has re- ported also on the patent litigation beginning in 1911 and ending in November 1923, when Minerals Separation's Patent 835,120 expired. He comments on

Jan 1, 1962

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923