Search Documents

By Donald C. Barton

Success in the use of the Eötvös torsion balance method of mapping geologic structure depends largely on the accuracy in the interpretation of the observed results. Skill in that interpretation depends (1) on the knowledge of the types of the variation of gravity, the gradient of gravity horizontally, and of the differential curvature produced by bodies of different sizes, shapes, dimensions, and densities; (2) on the knowledge of the possible types of structural bodies which might produce the observed anomalies; (3) on the empirical knowledge gained by experience not only in the geological interpretation of torsion balance surveys, hut of interpretations of inadequate geological data; and (4) on a knowledge of the possible and probable types of geologic structures in the area of the survey. The knowledge of the anomaly which a known body will produce and conversely the knowledge of the body or bodies which will produce a known anomaly may be gained by empirical experience and by mathematical study. The knowledge gained by empirical experience is fragmentary and inexact. The geology of most structures actually is known very superficially. The surface geology may be known accurately. If the structure is petroliferous, the subsurface geology of the oil field will be known down to 3000, 4000, 5000 ft. or in a few oil fields down to 7500 ft., but the deeper geology will be unknown and the metamorphic, igneous, or massive limestone basement below the reach of the drill may contrast sharply in density with the overlying sediments. Away from the oil field, the subsurface geology is known only from scattered drill holes, which do not go to the basement. A fair but not necessarily accurate knowledge of the geology of the nonproductive area can be obtained by correlation of the wells but the degree of its accuracy in general is proportional to the density of the occurrence of the wells. The geology below the bottom of the wells however is unknown. An anomaly mapped by the torsion balance is the sum of the effects of the contrasts in mass of its whole geologic surroundings. If the dimensions of a body of abnormal density are large enough, depth or distance makes no difference in the effects on the gradient and differential curvature; and as a matter of fact, in many places, the basement and irregulari-

Jan 1, 1929

By H. D. Colson, Robert A. Rapp

When a binary alloy is oxidized to form simultaneously an internal oxidation zone and an external scale which grows at a constant rate, the oxidation should reach a condition of steady shale, in which the internal oxidation zone is maintained at a time-independent thickness. Assuming an ideal model for the steady-state oxidation, the diffusion equation is solved for the steudy-state concentration profiles for oxygen and alloying- element in the metal. A theoretical prediction of' the steady-state thickness of the internal oxidation zone is made in terms of the experimental parameters. FOR the oxidation of binary alloys, Rhines, Johnson, and Anderson,1 as well as Mask: have derived equations describing the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which was assumed to mow according to a parabolic rate law. Experimental determinations of internal oxidation zone thicknesses beneath a Cu2O scale for Cu-Be and Cu-A1 alloys3,4 have shown some deviation from Maak's theoretical expressions, because the ideal model assumed for the calculation is not met experimentally. Some pure metals, such as columbium and tantalum oxidize at elevated temperatures and high oxygen pressures to form nonprotec-tive external scales which thicken at a constant rate. If such a base metal is alloyed with a solute element which may form a more stable oxide than the solvent oxide, then internal oxidation of solute may occur beneath the growing external scale. A review of the internal oxidation of alloys has been published recently.5 The purpose of this paper is to analyze theoretically for a binary alloy the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which grows at a constant rate. Consider an alloy A-B in which A is the more-noble solvent and B is the less-noble solute. The solute oxide is assumed to precipitate in internal oxidation as stoichiometric particles of BO, which are assumed to have a negligible solubility product in the A matrix. It is further assumed that the diffusion of oxygen through the zone of internal oxidation is not impeded by previously precipitated BO, particles. The specimen is assumed to be sufficiently thick so that the solute content in the center of the specimen does not change. For consistency: the following notation of Maak2 has been used:

Jan 1, 1967

By C. A. Stetefeldt

The iron-ore deposits worked by this Company occur in lenses 200 to 1000 feet long and 5 to 80 feet wide, and stand at an angle of from 65' to 75, with a vertical height of 250 to 500 feet, other lenses occurring below. A number of the deposits were first worked as open pits, which in some cases were carried to the depth of 150 feet, when, owing to the weakness of the walls, underground mining was adopted. While the ore was being removed from the open pit, shafts mere in several instances sunk into the foot-wall, the intention being to mine the ore with breast-stopes of an approximate height of 20 feet, followed by underhand-stopes of the same height, leaving floors between of the necessary thickness to support the walls, or to effect the removal of the ore by means of what is known as the stall system. As the work progressed, however, it was found that the walls (which are of chlorite) were too weak to permit the working of breast-stopes 20 feet high, there being frequent heavy falls of ground from the hanging and, in some instances, from the foot. The plan of following breast-stopes with underhand-stopes was, therefore, abandoned. By working breast-stopes only, but little more than one-half of the ore could be removed, and that only at an excessive cost, the ore being so hard that power-drills with 3 1/8-inch pistons . and 6-inch stroke, working under 60 pounds of compressed air, are able to drill but 8 feet in ten hours as a yearly average, while from 6 inches to 2 feet is a common result of ten hours' drilling. It was plain that some other system of mining must be adopted, and it was proposed to sink by levels of 75 feet, carrying in the cross-cuts from the shafts and working out the ore each way from the shaft from foot to hanging, and from 15 to 20 feet in height. When this has been done, drift-sets consisting of caps and legs are set up the whole length of the opening and connected with the cross-cut; the necessary openings for ladder-ways and chutes or mills are timbered from

Jan 1, 1893

By H. W. Mead, C. E. Birchenall

SELF-DIFFUSION of iron in austenite is a process which may play a significant role in some of the practically important reactions which occur in solid irons and steels. It also provides a system in which the interaction of vacancies on substitutional sites and atoms in interstitial positions may be investigated. For both purposes, accurate values of the diffusivities are required. Two sets of previous measurements exist, each containing features which require checking. In the course of an investigation to determine the rate of diffusion of iron in certain steels, Garwick and Rosenqvist' measured the self-diffusion coefficient of iron in a 0.10 pct* C steel and obtained a dicated that while at lower temperatures D increased with increasing carbon content, at the higher temperatures it first increased and then decreased. At the same time the activation energy decreased linearly from a value of 69,000 cal per g-atom for pure iron to 33,000 cal per g-atom at 1.06 pct C. This rapid decrease in activation energy implies that iron at higher temperatures within the austenite range would diffuse more slowly in high carbon steels than in steels of lower carbon content. Experimental Procedure The radioactive iron used in this work was obtained from Oak Ridge National Laboratory. The unit consisted of about 1 microcurie each of Fe7 and Fe It was allowed to decay for two years. At the end of this time most of the Fe with a half-life of 46.3 days, had decayed, while most of the original Fe(half-life 2.91 years) still remained. The iron as chloride was extracted into an ether layer, using the method of Ashley and M~rray. After evaporation of the ether the iron chloride was dissolved in 250 ml of aqueous solution containing 2.4 gpl Fe. The compositions of the steels used are listed in Table I. Disks of ¾ in. diam and about ¼ in. thick were machined from these steels for use in diffusion couples. The disks were surface ground on both sides to ensure parallel opposite faces. One face of each disk was polished through 000 emery paper. Half of the prepared disks were plated with radioactive iron. For this, 1 ml of the radioactive iron

Jan 1, 1957

By D. L. McElroy

It is too broad a statement to say that the mine car is the most important unit in a haulage system, but almost every mining man will admit that it is one of the most important. The mine car is to the mine haulage system what the railroad car is to the railroads; the main purpose in each instance is to move the greatest number of ton-miles of material at the least cost. The data presented in this paper are taken from a study of mine haulage conducted by the School of Mines of West Virginia University at 42 mines in 8 coal fields of Wrest Virginia. The study was made possible by a graduate fellowship of the School of Mines and the cooperation of the mining companies of the state. Three important factors in the use of mine cars in West Virginia are: (I) the number of mine cars in use per loader; (2) the capacity of mine cars; (3) the distribution of mine cars. ("Loaders" in this paper refers to all men loading coal, whether manually or mechanically.) During the World War many mine managers were annoyed by the reduction of efficiency and production caused by railroad-car shortages. Today relatively little complaint is heard about a shortage of mine cars, yet possibly 50 to 75 per cent. of the mines in West Virginia are suffering from this cause of reduced production and increased costs. The railroads have solved their car shortage by placing in service more cars of larger capacity and better design. Many coal mines in West Virginia should solve a part of their cost problems by the same simple procedure. Such a procedure requires an initial outlay of capital, but there is little doubt that this will be repaid, with a good return on the investment. Determining Number of Cars Needed There can be no mathematical rule to determine the number of cars which should be in use per loader in a coal mine, because numerous factors such as concentration of mining, system of haulage, car capacity, speed of haulage, distance of working places from tipple, and so forth, affect materially the number of cars in use. These factors in turn are more or less determined by height of bed, character of roof and coal,

Jan 1, 1931

By E. J. Whittenberger, F. N. Rhines

The formation of casting porosity is viewed as a nucleation and growth process with solidification shrinkage and gas precipitation as cooperative driving forces. Experimental evidence evaluating the individual contribution of each force confirms the major premise that microporosity is nucleated by gas precipitation. Additional data disclose the effects of the identity and quantity of gas, the temperature range of freezing, and the freezing rate upon the amount and distribution of porosity in light metal castings. POROSITY, as it commonly occurs in metal castings, has been ascribed to the contraction that accompanies the freezing of the metal, to the evolution of dissolved gases from the liquid during cooling and freezing, and, most frequently, to a combination of the two.'" "Pipe" formation is universally associated with solidification shrinkage; spherical "gas holes" are understood to be retained bubbles of gas; but the origin of microporosity, which usually exhibits an irregular or scalloped outline when viewed in cross-section, remains a subject of continuing debate.", ' The present research constitutes an endeavor to show what parts are played respectively by shrinkage and gas evolution in the initiation and growth of micropores and what factors determine their number, size, shape, and distribution. A preliminary outline of the mechanism of cavity formation in castings will serve to coordinate the experimental findings that will be reported and will at the same time provide a general theory of the origin of casting porosity. Basic to the mechanism of cavity formation that will be proposed are the following established facts: 1—that liquid metals and alloys contract gradually during cooling down to the freezing range, where a relatively large contraction, known as the "solidification shrinkage," takes place (exceptions in bismuth and gallium being noted);' 2—that the capacity of liquid metals and alloys for dissolving gases diminishes with cooling until, in the freezing interval, a large decrease takes place (various exceptions being noted and excluded from present consideration) ;.: and 3—that freezing proceeds counter to the direction of heat flow, the freezing front most commonly being composed of a system of tapering dendrite stalks and side arms which are coarser the lower the freezing rate and which protrude into the liquid for a distance that is greater the longer the freezing temperature interval of the alloy and the smaller the thermal gradient.' The mechanism by which voids are generated

Jan 1, 1953

By R. H. Richman

Coarse-grained Fe-Ni-C martensites formed at subzero temperatures were strained in compression at room temperature and the plastic deformation modes examined as a funclion of carbon content. At very low carbon levels, defovmation occurs hy wavy slip; commencing at about 0.05 pct C, mechanical twinning accounts for an increasing proportion of the plastic flow. Beyond approximately 0.4 pct C the deformation appears to be entirely by mechanical twinning. The habit planes of the operative twin modes were determined to be (113), (0131, and "(089)" in decreasing frequency of occurrence. Some of the implicaticms of Ihe o6served deformation modes upon the structure and properties of ferrous martensites are discussed. METALLURGISTS have long sought to explain the mechanical properties of ferrous martensites, particularly the extraordinary hardness and strength of the high-carbon varieties. Until recently the lack of precise knowledge of the structure of martensite crystals was the most serious barrier to understanding; however, the advent of thin-foil techniques for transmission electron microscopy has removed much of the mystery from martensite structure. Observations by Kelly and Nutting,"' and many others since, indicate that Fe-C based martensite crystals are internally twinned to a degree dependent upon the carbon content, and that a martensite plate containing 0.8 wt pct C or more consists of a stack of twin-related lamellae with each lamella on the order of l00A thick. Such a structure would be expected to influence greatly all aspects of metallurgical behavior, and many of the properties of Fe-C based martensites have been rationalized accordingly. Recent independent experiments led Winchell and cohen3 to conclude that the strength of ferrous martensite is derived primarily from solid solution hardening of the iron lattice by interstitial carbon atoms. Strength contributions from precipitation, dislocation-atmosphere interactions, clustering, short-range order, crystallite size, and so forth, were considered to be of secondary importance. In the view of Winchell and Cohen, the twinned structure of martensite serves mainly to limit the effective length of dislocation lines in the lattice, and thereby confers an added measure of hardening. Few properties of metallic crystals are as sensitive to metallurgical structure as are deformation mechanisms. It is somewhat surprising therefore, that, except for metallographic evidence of mechanical twins in strained martensite,4 no systematic examination of plastic deformation

Jan 1, 1963

By E. W. Davis

If the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indications that this new process may make commercially possible the manufacture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to magnetite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe203) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red temperature in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900' F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1939

By E. W. Davis

If the tonnage of merchantable iron ore remaining in the Lake Superior district is divided by the average of the annual shipments for the past 20 years, it will be found that this ore supply will be exhausted in approximately 35 years. This computed exhaustion period would be an indication of the future activities of the iron-mining industry if it were not for the fact that merchantable ore is being manufactured from low-grade ore, of which there is an almost inexhaustible supply in the Lake Superior district. It is true that at present only the simplest of these low-grade ores are being concentrated to any considerable extent, but progress is being made with the treatment of the more complex ores, and now, in addition to 20 washing plants on the Mesabi Range, three plants are equipped with jigs for the treatment of ore that cannot be concentrated simply by washing. The latest addition to the ore-treating plants of the Mesabi Range is a magnetic roasting and concentration plant at Cooley, Minn., in which ore that cannot be concentrated either by washing or by jigging is roasted to the magnetic state and concentrated on magnetic separators. This plant is beginning its third season of operation, and while it is too soon to make definite predictions, there are strong indications that this new process may make commercially possible the manufacture of high-grade, merchantable iron ore from large quantities of low-grade ore now considered worthless. After the iron oxide contained in an ore has been converted to magnetite, almost any desired grade of concentrate can be produced, using magnetic-concentration equipment of the types now in general use for the concentration of the natural magnetites of New York, New Jersey and Pennsylvania. The conversion of hematite (Fe203) to magnetite (Fe3O4) is easily accomplished by heating the ore to a dull red temperature in a reducing atmosphere. The reaction is slightly endothermic, and while it requires 200 B.t.u. to heat to 900' F. one pound of hematite ore containing 45 per cent Fe, it requires only 100 B.t.u. to convert the oxide into magnetite. In the laboratory, using small quantities of ore, this conversion is very simple, but large furnaces suitable for commercial

Jan 1, 1939

By Vernon Taylor

CANADA'S oil production is obtained almost entirely from the Turner Valley gas and oil field, in the Province of Alberta. This field, about 30 miles southwest of the city of Calgary and approximately 115 miles north of the United States border, supplied 92 per cent of production in Canada during 1937. In 1938 considerable development took place in this field and total production for the year amounted to 6,688,716 bbl., an increase of 3,922,146 bbl. over the production in 1937, which increased the percentage of production to approximately 97 per cent of Canada's total. In the British Empire, Canada's production is thus comparable to that of Bahrein Island and Burma, each of which produced approxi-mately 7,800,000 bbl. in 1937, being second to Trinidad's production of 15,500,000 bbl. The total production of the British Empire in that year amounted to 2.07 per cent of the world's total. HISTORY Development of the Turner Valley field commenced in 1913, when a well was started near a gas seepage on the banks of the South Fork of Sheep River in the central part of the Valley. This well found small quantities of a light crude oil in beds of Upper Cretaceous age and pre-cipitated a wild boom in 1913-1914 which ended with the beginning of the Great War in 1914. A small amount of drilling was done in the years from 1914 to 1922 and a few wells found small crude-oil production in the upper sands. In 1922 a few wells were started, including the Royalite Oil Company's No. 4 well (R, Fig. 1), which became the discovery well of naphtha pro-duction from the Paleozoic limestone. In October 1924, this well was completed at a depth of 3740 ft., being approximately 300 ft, in the lime-stone, with an initial flow of 600 bbl. of 72° A.P.I. gravity naphtha and 20,000 M cu. ft. of gas per day. Intense activity was not started until the latter part of 1928, when the Okalta No. 1 well (Q, Fig. 1) was drilled, with an initial production of 500 bbl. of naphtha per day. This well was only 1 ¼ miles from Royalite No. 4, but it was approximately 1300 ft.

Jan 1, 1939

By H. H. Power, Charles R. Houssiere

THE development of effective and dependable methods for drilling through the so-called "heaving-shale" horizons, particularly in the Gulf Coast area, is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Many mechanical remedies have been proposed and are in use in troublesome areas for combating heaving shale. However, in conducting a research program it was concluded that the physical and chemical properties of shales should be investigated, and the effect of added chemicals on such properties determined. As a preliminary step, the effect of chemicals on bentonitic suspensions was determined in accordance with recent contributions in the field of ceramics. The most plausible theoretical explanations for the behavior of the clay minerals involved are offered in the paper that follows. It is hoped that subsequent investigation of actual shale from troublesome wells will be aided by the initial work done on bentonitic suspensions of known composition. INTRODUCTION Formations variously designated as "heaving shale," "sloughing shale" and "caving shale" impede and may even preclude drilling of oil wells, particularly in certain parts of the Gulf Coast. In a previous paper1 it has been stated that the development of effective and dependable methods for drilling through these troublesome beds is believed to comprise a major contribution to drilling technology, and to the task of finding and developing our undiscovered oil pools. Since the attack on the heaving-shale problem by mechanical means was principally a matter of field investigation, it was concluded that a research program should be concerned with the physical and chemical properties of heaving shales, and the effect of added chemicals on such properties. It was realized that a study of shales required an advanced knowledge of the behavior of the individual clay minerals. A thorough review of the literature led the authors to the conclusion that very recent contributions2.3 in the field of ceramics furnished the most plausible theoretical explanations for the behavior of clay minerals. Accordingly, these fundamental ideas will be used in an attempt to explain the behavior of more complex systems whose composition and replaceable ions are known. In order to obtain comparable results it was deemed important to select an easily procurable clay of uniform characteristics. Accordingly, Wyoming bentonite, which is marketed under the name of "Volclay,"* was used for the preliminary investigations. The chemical analysis reported by the distribution is given as follows:

Jan 1, 1941

By R. E. Zimmerman, T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may be helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4. In modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1950

By W. T. Lundy

THE forms in which sulphur is commonly found-native sulphur, sulphides of many metals and sulphates-are widely distributed throughout the world. The two first mentioned are the principal sources of sulphur. Substantial amounts of sulphur in some form are recovered from gases from industrial plants and from gases from smelters treating other minerals. In recent years, plants have been installed in the United States to recover sulphur in elemental form from sour gases."' The amount of sulphur so produced is small at the present time but undoubtedly will increase in the future. The recovery of sulphur from gases is not covered in this chapter, which is confined to: (1) native sulphur deposits of Texas and Louisiana; (2) those of Italy; (3) other scattered deposits of native sulphur; and (4) pyrites deposits found in many countries of the world.30 Sulphur, a nonmetallic element, occurs normally in well developed bipyramidal or tabular crystals of the orthorhombic system, as well as in stalactitic and earthy masses. The mineral has a distinctive yellow color, which may be dark and discolored by impurities; the streak is white; the luster is resinous; and the fracture is conchoidal to uneven. Sulphur is translucent to opaque; has a hardness of 1.5 to 2.5, a specific gravity of 2.05, and an atomic weight of 32.06.16 The molecular weight of the solid is expressed by the symbol SS and that of the liquid and vapor ranges from S2 to S8, depending on the temperature. Sulphur melts at a temperature between 2340 and 248°F, depending on its crystalline state, to a liquid of dark amber color, the boiling point of which is 832°F. The viscosity near the melting point is about that of water and increases to 50,000 times that of water at a temperature of 380°F, subsequently falling rapidly to a low figure at the boiling point. Crystallization changes slowly from rhombic to monoclinic above 205 °F and in cooling the transformation is reversed. The mineral is a very poor conductor of heat and electricity; it is insoluble in water and nearly all acids and is soluble in cold carbon bisulphide and carbon tetrachloride. It ignites in air at a temperature of 478°F, burning with a distinctive blue flame with evolution of sulphur dioxide.47

Jan 1, 1949

By Philip W. Henry

There is a difference of opinion among engineers on the subject of depreciation in general, and still more on its application to any given case The committee which was appointed by the American Society of Civil Engineers to make a report on Valuation of Public Utilities, states "There is no subject connected with valuation about which there are more diverse views than those relating to depreciation;" and in the discussion which took place upon the presentation of the preliminary report of this committee in January, 1914, that part of the report dealing with depreciation called forth more discussion than any other. From this discussion it was evident that the word "depreciation" was not always used in the same sense, so it is quite important that some definition be adopted. As this paper relates to the proper method of treating depreciation by corporations or individuals operating oil properties, both of which must make a return of annual net income to the government in connection with the income tax, it will be in order to adopt the definition of the Internal Revenue Bureau. Under date of Mar. 29, 1910, the Commissioner of Internal Revenue of the Treasury Department stated "Deduction on account of depreciation of property must be based on lifetime of property, its cost, value and use." Again, on Form 1035, "Return of Annual Net Income" for miscellaneous corporations (Section 2, Act of Congress approved Oct. 3, 1913), a deduction from gross income is allowed for "Total amount of depreciation for the year." This item is defined more particularly as follows: "The amount claimed under Item No. 5 (b) for depreciation should be such an amount as measures the loss which the corporation actually sustains during the year in the value of buildings, machinery, and such other property as is subject to depreciation on account of wear and tear, exhaustion, or obsolescence. The amount taken credit for on this account in order to be allowable should be so entered on the books as to constitute a liability against the assets of the corporation. The amount claimed under this item should not cover losses in the value of stocks and bonds. Decrease in the book value of securities owned, so far as such decrease represents a decline in the actual value of such securities, should be deducted under item 5 (a) of the return. "Where depreciation of physical property is made good by renewals, replacements,

Jan 1, 1915

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type3 Prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution. The alternatives to retreat mining with multiple entries are: Modified retreat mining- where the tail-entry is being formed during the mining of-the panel ("2"-system). Some form of advance mining-where the head-entry or both head and tail entries are being formed as part of the longwall extraction process. These methods are well-known and well-established. Variants of them are being practiced in Canada, Central and South America, but not in the US. It is primarily the laws governing ventilation-conceived for room and pillar mining which prevent the rapid development of these techniques. Another aspect of longwall mining is that it requires a systematic and consistent approach in organization, roof control, ventilation and transport. It is for this reason that compliance with health and safety regulation is fairly well ensured if the longwall system has been well laid out and is subsequently well-run. Nevertheless, a management mentality raised in the great flexibility of the room and pillar system cannot always come to terms with the degree of forward planning and rigid discipline required to successful longwall mining. Research, development and other investments in the partial aspects of longwall mining are always of interest, but no massive trend to longwall can be expected realistically unless these major stumbling blocks in the basic law and basic approach are effectively removed.

Jan 1, 1980

By L. D. Jaffe Hollomon, Hollomon John H.

For many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure.' and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearl-itic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. Quench Cracking Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1947

By R. B. Russell

The expansion coefficients of hexagonal (a) zirconium have been calculated from the lattice expansionparameters of both coefficientsofhexagonallow and high hafnium alloys in the range 0° to 600°C. It is found parametersofboththat the coefficients are straight-line functions of the temperature and that the effect of hafnium is to depress the mean coefficients by about 1 pct at room thattemperature and 9 pct at 600°C. The cubic (ß) form was stabilized so that its coefficient could be determined from 400' to 900°C. COEFFICIENTS of thermal expansion for hexagonal-close-packed (a) zirconium were determined up to 600°C (1112°F), without any interference from the effects of preferred orientation, by measurement of the lattice parameters obtained from a symmetrical back-reflection focusing X-ray camera. This paper combines the results for a 1.2 atomic pct hafnium alloy from an earlier report' with those for hafnium-free zirconium. The problem confronting the investigator is essentially that of getting sharp, high-angle diffraction lines which represent the material at a known constanl. temperature and chemical composition. In order to do this, it was necessary to use the proper X-ray emission wave length (Co K was chosen) and to have a fine-grained metal whose atomic spacings would be free from effects of cold work (the specimen was annealed) and to prevent a changing composition owing to gas absorption during the heating of the metal to temperature (the sample was heated in a vacuum). A summary of the effect of temperature on properties is listed in Table I which gives data for ordinary zirconium, as well as new values for the low hafnium metal. The coefficients of the linear thermal expansion that have been reported are given in Table 11. The discrepancies shown may be explained perhaps by the effect of preferred orientation, and McGeary and Lustman2 have done this successfully for sheet metal. The differences in texture cannot explain all the differences in expansion coefficient shown in Table II. liesults by the author agree most closely with those of Kroll.3 Chemical analysis of the high hafnium metal pre- viously reported1 showed that it was 98.22 atomic pct (97.40 wt pct) pure. The low hafnium metal was dehydrogenated Westinghouse crystal bar, designated SMZ-137A. Its analysis was as given in Table 111 (chemical analyses 5377, 5431, and 5432).

Jan 1, 1955

By Hollomon John H., L. D. Jaffe Hollomon

For many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure.' and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearl-itic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. Quench Cracking Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1947

By B. H. Lehnhard, C. J. Cecil

The paper describes the use of the Electric Pilot in the Permian Basin for making permeability surveys of wells and for the selective acidization of wells. A general summary of the information obtained from the many permeability surveys run in this area is given, and the possible application of this information to reservoir control problems is discussed. The application of the Electric Pilot on specific wells, involving well completion, acidizing and workover operations is also included. Introduction The Electric pilot is a comparatively new tool in oil-producing areas. From the beginning, the possibilities of this new service caught the imagination of many of the oil operators and acidizing engineers. Through the continued and ever increasing use of the pilot during the past year, and the close cooperation of the oil operators who have used this service, the efficiency and utility of the Electric Pilot service has been increased to a point where it is now a well established and recognized service. There are two major uses for the Electric Pilot: (I) permeability survey; (2) selective acid treatments. Permeability surveys are made to determine the thickness of the various permeable sections at the borehole, the vertical position of these zones at the bore hole, and the relative capacities of the various zones. Nomenclature Data obtained from the permeability survey are used to calculate three different indexes that pertain to the volume of fluid injected into the various permeable zones. A nomenclature for these various indexes has been set up, which correspond with the various productivity indexes, except that they are a measure of injected fluid rather than produced fluid. The nomenclature and definition of the indexes used in connection with a permeability survey by the Electric Pilot are as follows: 1. Capacity.—The volume of water injected into an individual permeable zone, in gallons Per minute. 2. Capacity Index.—The volume of water injected into an individual permeable Zone, in gallons Per minute Per pound Per Square inch differential Pressure. 3. Specific Capacity Index.—The volume of water injected into an individual permable zone in gallons Per minute Per pound per square inch differential per foot of thickness of the zone at the borehole. Capacity is the most generally used index, and for planning initial acidizing procedures and most workover jobs it is sufficient. For comparing permeability surveys on the same well before and after

Jan 1, 1945

By E. D. Gardner

Apparently the widespread agitation for the codification of our mining laws has had its effect, and it is quite possible that Congress will take up the question during this present session. The greatest objection to our present statutes pertaining to metalliferous deposits seems to be directed against the law of the apex. Those who are not in favor of changing this law are very far in the minority and they apparently realize that it is useless to urge its retention. Next in importance to the repeal of the law of the apex, seems to be a widespread advocacy for the repeal of the law requiring discovery of mineral before a valid location of a mining claim can be made. To a lesser extent there appears to be a desire to have the law changed so as to allow patent for claims without mineral discoveries. The purpose of this article is to review the arguments in favor of the proposed change of the discovery requirement, to show some of the evils that may be expected to result therefrom, and to consider whether a system may be devised to correct the undesirable features of the present law in this respect and at the same time not expose the mining fraternity and the general public to the evils which would result from the repeal of this fundamental requirement. Under the law as at present framed, the validity of a mining location is dependent upon the fact of discovery of mineral within the boundaries of the land claimed. " * * * but no location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located" (Sec. 2,320, U. S. Rev. Stat.). All authorities agree that discovery is the source of the miners' title. Lindley, in his valuable work on Mines (3d Ed., Sec. 335), lays down the rule in part as follows: "Discovery is the initial fact. Without that no right can be acquired. * * * Such discovery must precede the location, or be in advance of intervening rights. The proof of recording and marking a claim will not authorize the court to presume a discovery." As is well stated by the U. S. Supreme Court in Erhard v. Boaro (113 U.S. 536):

Jan 1, 1917