Search Documents

By Enrique Francisco Somolinos Garcia-Morales

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 1, 2018

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By Dalila Chaves Sicupira

A pitting corrosion study of welded joints of lean duplex stainless steel (LDSS) UNS S32304 has been performed. LDSS S32304 thick plates were welded by different processes commonly employed in equipment and piping construction: SMAW (Shielded metal arc welding), GMAW (Gas metal arc welding) and FCAW (Flux cored arc welding). The electrochemical behavior of different weldment zones (fusion zone (FZ), base metal (BM) and heat affected zone (HAZ)) was characterized both independently using an electrochemical microcell and together through whole sample analysis. The electrochemical method applied was performed in acidified glycerin, a process fluid of the biodiesel industry. The results were correlated to the microstructural features of the materials. Based on the results, is possible to conclude that the breakdown potential (Eb) of the fusion zone (FZ) was higher than the Eb obtained for the heat affected zone (HAZ). In general, top samples show higher breakdown potential than root samples and also the samples welded using filler metal 2209 has a better anodic behavior than the filler metal 2307. According to the results, GMAW welding process with 2209 as filler metal was revealed as the optimum chosen for application of 2304 duplex stainless steels in this case.

Jan 16, 2018

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019

By Jean-Paul Simoes

The development of the blast furnace over the last years lead to a substantial increase in production capacity and productivity. This development triggered an evolution of the cooling systems in order to cope with the raising heat loads. The excellent protection of the shell by copper staves allowed blast furnace operators to achieve campaign lifetimes of more than 20 years. However in recent years some blast furnaces have experienced severe wear of the copper staves due to abrasion. The influences of the blast furnace design as well as of the operation conditions on this premature wear have been analysed and the mechanisms leading to the wear will be explained. New developments in the copper stave technology are part of the solution for avoiding premature wear during periods with less favourable conditions. The protection mechanisms made available by the new design extend the inherent protection mechanisms of copper staves to these periods. BFXpert® system is the ideal tool for the monitoring of the process data, the process models and the recommendations given by Sachem® support the operator in choosing efficient operation points. The charging with a Bell Less Top® (BLT) allows an accurate controlling of the blast furnace with regard to the optimization of the gas distribution. High performance operation together with long campaign lifetimes are thus made possible.

Aug 1, 2018

By Woo, Hur, Kim, Ki Nam, Seung Min, Kyoung Sik

Tandem cold mill (TCM) is a process to obtain flatness as well as thickness desired by the customer by rolling hot-rolled coils continuously. The final stand of the TCM plays the most important role of flatness control, which usually uses the real-time measurement at the exit. However, as the material property increases, it is not easy to handle flatness with only the final stand. In order to overcome such a limitation, we propose a feedback control method to strengthen flatness control for non-final stands. The proposed method was tested in an actual production line, and the effect is proved for 45K or less steel grade.

Oct 1, 2019

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017

By Andrea Pezza

The steel market is experiencing a difficult conjuncture: on the one hand steel producers minimize their investments while optimizing their over- production, on the other hand suppliers reduce their internal human resources and capacity in order to overcome the instability of the new era. A return to the steel production levels of the past is not expected in the short term. Research, development and plant concept optimization is one recipe to drive the future of the steel business. This article describes a new concept for a VOD plant developed as a result of thorough investigation and assessment of all possible solutions. A joint and tight cooperation with the final customer was necessary to reaching important results. This article consists of the contributions from the plant suppliers in terms of their experience and feedback, as well as the final user’s. The final customer, voestalpine Giesserei Linz GmbH, and the plant supplier, Primetals Technologies, are both worldwide players and highly focused on reaching best quality and innovation.

Oct 30, 2017

By Bimal Nathwani

This paper presents an overview of bearings failures with focus on steel mill applications such as continuous casting, rolling mills, multi-roll cluster mills and wire and rod mills. This paper will also provide countermeasures for prevention of these modes of failures.

Jul 30, 2018

By Johan PEERS, François DUMORTIER

Today, solutions to optimize Capital Expenditure (CAPEX) & Operational Expenditure (OPEX) for small capacity Cold Rolling Mills (CRM) as well as for high capacity CRM are available, as extensively described by various Original Equipment Manufacturers (OEMs) & steel makers. A suitable solution for small capacity CRM is to start with a single stand reversing mill (up to 400 ktpy, depending on product mix), which can then be expanded into a twin stand mill (up to 900 ktpy, depending on product mix). The main drawbacks in conventional practice are the off-gauge length in single stand set-up and the long downtime of the mill during the erection of the second stand. For higher productions CRM, it is common practice to directly select a new Pickling Line Tandem Cold Mill (PLTCM), with a high CAPEX. Is there an in-between solution that would allow to start with limited output and CAPEX, without jeopardizing the ultimate expansion goal (1.2 to 2 mtpy), for which PLTCM is the best techno-economical choice? In the absence of a solution, JOHN COCKERILL developed an integrated solution that limits the CAPEX in the first phase of development, without crippling affecting future endeavors through an easy and economically sustainable expansion into a PLTCM, without long production downtime. The solution consists of first installing a twin stand mill, expandable into a tandem mill thanks to a smart design of the line. It is therefore possible to limit the production to 900 ktpy in the first phase of the project and then convert the mill into PLTCM in the second phase to increase the production from 1.2 to 2 mtpy, depending on the market trends and financial capabilities. In summary, JOHN COCKERILL has developed a smart new layout in reversing phase combined with a brand new rolling strategy to optimize productivity and limit off-gauge, compared to conventional solutions (patents pending). In addition the layout enables an easy conversion to tandem mill without high over investments, which is more sustainable financially than the initial purchase of a PLTCM. Long downtimes to allow for capacity extension, detrimental to this phase-by-phase approach, are also avoided. Technical and process description of the new layouts and rolling strategies, together with CAPEX & OPEX descriptions of the phases are detailed in this paper.

Oct 1, 2019

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Douglas Glenn Stalheim

The uniformity of the final cross sectional microstructure and subsequent final mechanical properties and shape of structural steels is dependent on the type or types of recrystallization behaviors that are created. There are three main recrystallization behaviors that are the foundation of the metallurgy created during production. Alloy design and subsequent processing design strategy drive how much of each recrystallization behavior is created through the cross section of the product. Carbon manganese steels create only one basic behavior while the addition of microalloys, in particular niobium, can add two additional behaviors. The behaviors are intertwined with each other and build upon each other. The three behaviors are Type I, static recrystallization, Type II, no-recrystallization, and Type III, metadynamic/dynamic recrystallization. How much of each behavior is generated through the cross section through the production influences the final transformed microstructure and corresponding mechanical properties and shape performance. This paper will discuss the three behaviors, how they are generated, how to identify which behavior is occurring through modeling or actual mill data. Actual examples from production will be discussed.

Aug 16, 2017

By Antônio Aldenor Pinheiro Neto, Matheus de Lima Vieira

In mid-2015 the steel industry faced a strong crisis due to the weak performance of the Brazilian economy and the persistent entry of Chinese steel into Brazilian territory. This situation demanded that Brazilian steelmakers seek to develop products to meet new export markets. within the volume of exports possible are the rebars, where its applications are in the construction industry. One of the largest importers is Peru which has a large percentage of this export volume. This market demands as a priority requirement the surface quality of blue condition (low oxidation index) and mechanical properties normative.in order to meet the items required by the customer at a competitive cost, a vanadium microalloyed steel was applied to the hot rolling process without heat treatment after the last rolling pass. Where the great challenge was to achieve a high level of stretching without compromising the minimum limits of tensile strength. Assuming that the steel used is the correct one interventions were made on rolling parameters such as set-point temperature, residence time of pieces in the furnace, linear mass and rolling speed. All the changes made were based on statistical tools and practical tests. Finally, with the execution of actions generated from the statistical analyzes and tests it was possible to reduce process losses by 96%.

Oct 1, 2019

By Erich Bartel

The Kocks Rotation Mill - KRM- is an innovative elongation method for seamless tube production up to 4.5’’ diameter at production levels up to150,000 TPY. Using the principle of cross roll elongation, the machine rotates four rolls around the workpiece. A retained mandrel sets the wall thickness to a precision that exceeds existing industry norms. The KRM process performance has been truly excellent. Attributes include high billet weights, elongation of up to 9.5 in one pass, and eccentricity at or below +/- 5.0%. The flexibility of the process allows a wide range of steel grades to be produced at any wall thickness with little or no mill down time. Surface quality and yield are also greatly improved. Based upon the small foot print of the KRM rotor as well as the simple mandrel manipulation system, the installation cost of the KRM is significantly lower compared to other elongation methods. The reasonable cost of the machine, combined with greatly reduced foundation requirements, reduced ceiling height as well as simple utility connections reduce the initial investment for a new or upgraded mill. Finally, lower roll and mandrel costs allow high quality production at greatly reduces cost/ton.

Aug 16, 2017

By Anna Carolina Cerqueira Neves

Synthetic fibers have been gradually replaced by lignocellulosic fibers. Compared to the synthetic fiber, natural fiber showed economic and environmental advantages presenting interfacial characteristics with polymer matrices that favor the impact energy absorption by the composite structure. However, so far little has been reported about the hemp fiber embedded in polymer matrices, such as tensile properties. This study aims to evaluate the resistance in tensile tests of epoxies composites reinforced with different percentages of hemp fiber. Tensile tests were submitted with percentage of 0%, 10%, 20% and 30% incorporated hemp fiber in epoxy matrix. The tensile strength and deformation substantially increased the relative amount of hemp fibers incorporated into the polymeric matrix.

Aug 16, 2017

By Thomas Germershausen

Worldwide BOF-based steel plants are faced with demanding environmental requests and rising energy costs. For cleaning of primary gases from the BOF the scrubbing technology is worldwide adapted. For wet-scrubbers there is a direct relation between pressure loss and achievable clean gas dust content. Subsequently main energy consumers within Gas Cleaning Plants are the driving fans. To evaluate actual performance and to identify optimization measures extensive field measurements at existing Gas Cleaning Plants were performed. The operational results from various BOF plants worldwide will be presented and benchmarked. As a conclusion, advanced control strategies for reduced energy consumption and lower environmental impact were developed and implemented.

Jul 30, 2018

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017

By Lesli Peterson

Spraying Systems Co® has continued to develop and evolve descale nozzles through the years. The most recent addition to the descale nozzle line, the DescaleJet® Pro, provides more impact and a more uniform distribution than previous descale nozzles. The improved performance has been achieved through multiple design changes such as a smoother approach, updated vane design and improved carbide orifice. In addition to providing improved spray performance the nozzle also lasts longer than previous versions. The new technology has been thoroughly tested in the lab using impact measurements and accelerated wear testing. In addition to lab testing the nozzle has provided improved performance and longer wear life for those that have made the change to the new technology. The new nozzle technology and the benefits to the rolling mill will be discussed.

Jul 30, 2018

By Jan Knobloch

Inter Stand Cooling (ISC) can increase productivity of a HSM and improve final mechanical properties of the strip. Constant Target Exit Temperature can be ensured for the whole strip length eliminating skid marks and other temperature oscillations of the transfer bar. The paper deals with advanced control module of ISC. Essential mathematical models of the control system is introduced and basic functionality is explained. Temperature model is based on FEM. Mechanical and thermal properties of the strip are calculated from chemical composition using neural network. Further on an experimental possibilities for investigation and design of ISC cooling headers will be shown. In conclusion practical experience with ISC on various HSM will be discussed.

Jul 30, 2018

By Tiago Seixas Bittencourt

Technological developments, associated with the constant worry about the environmental impacts arising from industrial activity, it has driven the development of technologies and practices for efficient fumes and particulates capture arising from the manufacturing processes of steel in steel plants in general. Currently, the electric steelshops in operation with Electric Arc Furnaces (EAF), seek parameterize/design dedusting systems able to retain most of the particulates generated during melting and refining of steel in FEA through configurations of equipment, technologies and parameters operation in order to equalize the antagonistic relationship between effective fumes capture and energy balance of the EAF. The present work gets as a fundamental premise to evaluate critically the possible different settings of the usual dust removal systems, as well as their respective classical parameterizations. The work main purpose is to establish a general rule evaluation technique for dedusting system considering the different modes of operation of an Electric Arc Furnace.

Jul 30, 2018