Search Documents

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Paolo Demetlika

In this paper it is shown how the “Zero Operator” concept on the casting floor has been reached by adoption of a standard 6 axis industrial anthropomorphic robot coupled with the most innovative machine vision technology. This has been achieved by automating all the operations related to the ladle and tundish activities, including shroud manipulation, powder addition, ladle nozzle identification, nozzle opening by lancing, temperature measurement and chemical sampling. Q–Robot CAST family products are the result of the successful alliance between industrial robotics and the most advanced technology in process automation. This led, for each production area, to the introduction of flexible automation in dangerous places, even where some degree of human intervention is still necessary. By using anthropomorphic robots, human operators can be reassigned to safer environments. Furthermore, robots are suited to deal with repetitive and labor intensive tasks thus guaranteeing a high process quality.

Oct 30, 2017

By Breno Totti Maia

This work was a continuous and multidisciplinary development. Through studies of the blowing process and its parameters results, evolutions, improvements and adjustments were made on the lance’s hot face with Slagless® technology, as well in the process parameters and mitigating actions of the projection of materials out of the converter. The main results are the increase in the nozzle’s life with a “record mark” of 1785 heats, and water leakage occurrence in the cartridge decreased considerably reaching the mark of one year without any occurrence.

Oct 30, 2017

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By Karl Berger

The paper gives a comprehensive overview of the historical development of various metal rolling technologies and also describes the influence to industrial and socio-economic developments. The rolling of steel, in particular of rails, beams, rebar, strip and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. All this has changed the face of the world significantly. Further the paper approaches technological highlights in the design, manufacturing, drive and control of modern mills and the various types developed to create industrial economic units for the different markets and customers’ requirements. An outlook of future challenges is as well discussed in the paper. Various solution approaches for the rolling technologies, from continuous improvement of existing plants to more radical new concepts like endless rolling, near net-shape casting and rolling are approached. A positive conclusion is drawn that rolling technologies will remain a valuable area for engineers with scientific and economic challenges, but also a clear vision for positive contribution to further industrial and social development.

Jul 30, 2018

By Samuel Filgueiras Rodrigues, Clodualdo Aranas Jr., Gedeon Silva Reis, Eden Santos Silva, Fulvio Siciliano

When austenite is deformed above the Ae3 temperature, partial amount of it transforms dynamically into ferrite by a displacive mechanism. After unloading, it retransforms back into the stable austenite by a diffusional process. This influences the rolling load which decreases under isothermal condition or does not increase with decreasing temperature as rapidly as expected under cooling. Plate rolling simulations under isothermal and continuous cooling conditions were carried out on a 0.09 wt.% Nb X-70 steel. Pass strains of 0.2 were employed together with interpass times of 10 s, and 30 s for the cooling conditions and 0.3 with interval of 10 s at 900 °C for the isothermal experiments; strain rate of 1 s-1 was used during the simulations. The mean-flow-stress (MFS`s) behavior of both conditions indicates that dynamic transformation and dynamic recrystallization were taking place during straining. The critical strains for the initiation of dynamic transformation fell around 0.06 while the critical strain for DRX was 0.12. It has been shown that ferrite is formed due to the applied deformation of roughing passes and increases its volume fraction throughout the finishing rolling stage. Under cooling conditions, the ferrite formation is also favored as the temperature approaches the Ae3 line. Such ferrite forms when the driving force for dynamic transformation is higher than the total free energy barrier preventing its formation. This obstacle consists of the free energy difference between austenite and ferrite as well as the lattice dilatation work and shear accommodation work. The addition of Nb retards the retransformation of the ferrite into austenite. Moreover, holding times after rolling increases the amount of austenite available for microstructure control on subsequent stages. The dynamic transformation (DT) mechanism can be used to design improved rolling schedules

Oct 1, 2019

By Dr. Steven G. Jansto

The market demand for reduced fuel consumption and CO2 emissions in the automotive, energy and construction sectors have further increased the demand for new and advanced higher quality microalloyed grades produced via TMCP. The technological integration of the process and physical metallurgical advancements of value-added niobium (Nb) microalloyed thermo-mechanical controlled process (TMCP) steels continue to be developed and is an important element for these more demanding end user requirements and cost-effective steel production. The reheat furnace process step has a profound effect on the TMCP performance, final hot rolled steel quality and mechanical property consistency during the production of hot rolled steels. The uniformity of heating applied across the entire width, thickness and length of the slab or billet is essential in the successful achievement of consistent customer properties regardless of the chemistry. The resultant ferrite grain size in the final hot rolled product is significantly governed by the initial prior austenite grain size. However, the transition from laboratory melted and TMCP hot rolled heats to the production scale is often quite challenging. Aberrations in the reheating process step at the industrial furnace are often the root cause of mechanical property quality issues. These combustion process metallurgy parameters connect directly to the resultant TMCP product quality and is defined as Combustion Metallurgy

Oct 1, 2019

By Marcela Gotelip Barbosa

Pellets are the main iron input to the blast furnace at ArcelorMittal Lazaro Cardenas iron and steel making facility in Mexico. Pellets are made at this facility using the concentrates generated and shipped from their captive mines viz., Las Truchas, Pena Colorada, Volcan Sonora. The concentrating plants, after grinding the ore to the liberation size, use magnetic separation and flotation to reject the silica, sulphur and phosphorous impurities. At Volcan Sonora Mines, the ore is contaminated with phosphorous minerals, and hence, after magnetic separation, the phosphate minerals are floated using anionic carboxylate collector (sodium oleate). Apart from floating the phosphate minerals, the sodium oleate also has some tendency to smear on the iron bearing mineral surfaces leaving a hydrophobic surface, which is expected to reduce the green pellet strength due to absorption of ultrafine sized air bubbles on these surfaces, and further generate higher levels of dust during the induration process. In order to alleviate this industrial problem, comparative studies were carried out on the concentrates from magnetic separation using reagents from synthetic sarcosinate and carboxylate family collectors. Results have indicated that the sarcosinate family members not only were found as replacement to carboxylate collectors, but also reduce the phosphorous content below the values achieved with oleate, thus have considerable benefits in the downstream steel making process. Based on the results, plant runs are being taken up at Volcan Sonora. In this article, the laboratory results obtained on iron grades and recoveries, and phosphorous rejection using both the reagents are presented.

Aug 1, 2018

By Filippo Verlezza

The 3-roll technology is a recognized process applied to SBQ production. The main aim of this paper is to show the latest developments on this technology including other equipment´s that also contributes for a better performance on SBQ coils production.

Jul 30, 2018

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the virgin condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 69 to 258 MPa producing rupture times varying from 8 to about 4908 h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results mentioned in literature for the same material in the virgin condition.

Aug 16, 2017

By Jorge Madias

O trabalho está centrado na análise comparativa de normas de vinte paises/regiões sobre vergalhão, escolhidos levando em conta os principais paises productores, exportadores, e consumidores deste produto para a construção civil. São comparadas as propriedades mecânicas: limite de escoamento, resistência à tração, elongamento à rotura, elongamento uniforme, relação escoamento/tração), a análise química, testes especiais como fadiga e adherência e outros ítens. Tambén é tida em conta a evolução dos quesitos das normas ao longo do tempo. O foco é o comportamento anti seismo do vergalhão.

Oct 30, 2017

By Renan Bueno Wojciechowski, Yukio Shigaki

The quality of flat rolling process depends highly on multiple factors such as applied forces, materials involved for both strip and rolls, roll geometry and its positioning. To calculate the strip shape, a mathematical/numerical model can be applied, showing the final product and how the equipment behaves when changing some parameters. This is usually a time-consuming task for both user and computer, especially when it involves thin and hard strips. By coupling a quick rolling load calculation method as Bland-Ford and Finite Element Method (FEM) for roll stack deformation, it is possible to create an accurate and user-friendly rolling simulator. This paper presents the improvements done in the 3D FEM/multi-slab method and its actual capabilities by simulating two cases of a 6-High rolling mill. Different analysis in this equipment can be easily done in about 10 minutes by using the developed an electronic spreadsheet program interface and the folder generated with relevant results and logs. An operation manual and a commercial FE program plugins were made to aid construction of a completely new model. The code was created in a modularized way to assist the application of this simulator for other operational conditions.

Oct 1, 2019

By Elham Kordzadeh

As the world’s reserves of coarse and high-grade iron ores continue to shrink, beneficiation is becoming increasingly important. The resulting concentrates cannot be used directly as feedstock for iron making, but require an additional agglomeration step. Pelletizing is preferred, because the uniform chemical, physical, and metallurgical characteristics of pellets make them a more desirable feed for the iron making processes. The heat hardening or induration of pellets is typically done in shaft furnaces, grate-kiln systems or on straight grates. Rotary kilns were originally developed in the late 19th century for Portland cement production [1]. The main development work for the successful adaptation of the process to the thermal treatment (induration) of green balls from iron ore was performed by Allis Chalmers in Milwaukee, Wisconsin, USA in the 1960’s [2].The straight grate process, which was first used in 1955 at Silver Bay, Minnesota, was a dedicated development with the aim to pelletize and indurate magnetite (taconite) concentrate [2]. There are various important technical and economical distinctions between the two pelletizing technologies. The most important differences include that a grate-kiln has three distinct pieces of equipment, a preheat grate, a rotary kiln and an annular cooler, whereas in the case of a straight grate, the entire indurating process is done on one piece of equipment only. In addition, both technological solutions have differences in their recuperation systems, direction of air flow in drying, number of burners, form of pellet movement, etc., which cause differences in raw material suitability, process control, economical aspects, plant operation and product pellet quality.

Oct 30, 2017

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017