Search Documents

By Günther Staudinge

Aperam is a global player in producing of stainless, electrical and special steel qualities. The steelmaking plant in Timoteo Brasil is equipped with one AODconverter for stainless steel and one MRPL-converter for special steel production. After almost 20 years of operation Aperam decided to exchange the existing 80 t MRP-L converter by a new one including a new trunnion ring and a state of the art suspension system. Due to an optimized design the inner volume of the new converter could be increased which comes along with improved production. A special feature is a flange connection in the barrel section of the converter. This allowed to avoid any critical site welding and the time between shut down of the old and cold commissioning of the new converter could be done with 17 days only.

Aug 17, 2017

By Christoph Aichinger

The optimization and improvement of a modern integral iron and steel works gets more and more difficult as each individual plant is already operated at its best efficiency and at the lowest operational expenditures. However very often the individual plants are considered as stand-alone units and there are losses and inconsistencies on interfaces and take over points, which could be avoided and by that improving the overall performance of the iron and steel works as a holistic unit. Primetals Technologies looked into this subject extensively in the recent years and is now ready to offer new tools and services in order to assist operators to find further potential for improvement in processes, which seem to be fully developed at first sight.

Aug 17, 2017

By Thierno FALL

This paper describes the study of the work-roll during the hot rolling process thanks to a 3D model built with the Finite Element Method (FEM). In terms of computational cost, that method needs high resources compared to 1D model which are mostly used. However, the 3D model is built to have a better understanding of the work-roll thermal and mechanical behavior during the hot rolling process. The thermal model shows that the highest temperature reached during rolling are within the range of 500°C and 600°C. The thermal field input used to simulate the mechanical behavior of the work-roll shows a biaxial thermal stress state, in the circumferential and axial planes. However, a peak of radial stress is observed in the backup zone. It did not generate plastic strain but could influence the fatigue behavior of the work-roll.

Oct 1, 2019

By Li Shanqing, Xu Jianghua, Li Hongmei, Huang Peijie

Cold rolled high strength steel are playing a very important role in reducing automobile weight for energy saving and environment protection. In recent year, more and more high strength steel were manufacturing in steel company. But there are some problems in the cold rolling process for high strength steel products. Periodic thickness deviation especially in strip head or tail is an important one in these problems. In this paper, the reason of periodic thickness deviation was analysed and a new AGC algorithm called Property FFC for high strength steel in tandem cold rolling was developed. The application of this new algorithm shows that it can reduce the thickness deviation.

Oct 1, 2019

By Luis Armando Espitia

AISI 410 martensitic stainless steel specimens were low temperature plasma nitrided at 400°C in a mixture of 75%N2:25%H2, during 20 h. Active screen technic was used to avoid any edge effect The nitrided case is composed of expanded martensite (a’N) and e-Fe3N iron nitride, whilst chromium nitride precipitation was avoided. Surface hardness reached 1275 HV0.01. The transverse microhardness profile shows a gentle hardness gradient with a NHT nitrided case depth of 28 µm. Nanoindentation tests were carried out in order to assess the hardness (H), the Young modulus (E), the H/E and H3/E2 ratios and the elastic recovery (We) of both nitrided and non-nitrided specimens. The cavitation erosion mass losses were measured as a function of exposure time. The results showed a decrease of 27 times of the mass loss compared to the non-nitride specimens. Wear rate decreased from 2.56 mg/h for the non-nitrided condition to 0.085 mg/h after nitriding. The increment in the elastic recovery and the higher hardness values are responsible for the greater cavitation erosion resistance exhibited by the expanded martensite. Such results showed that low temperature plasma nitriding and the formation of expanded martensite are effective to increase cavitation erosion resistance of AISI 410 stainless steel.

Jul 31, 2018

By Alessandra Spaghetti

Rolling small-diameter hot wire rods at high speeds with conventional laying head pipes can wear the pipe out frequently and affect quality and consistency in the final product. Laying head upgrades using Sandvik SAF2507LHP™ (UNS S32750) tubes make possible to achieve optimal metallurgical properties, smooth coil formation and easier coil handling. Operators can also avoid unwelcome shutdowns due to frequent worn pipe changes and turndowns. Sandvik have been developing different customers and understand their process needs. The suitable selection materials that are able to withstand high levels of wear better than low alloy and carbon steel grades that are commonly used in industry is very important to improve the quality and increase productivity. UNS S32750 tubes were demonstrably superior to low alloy and carbon steels when used in Laying Head Pipe system regarding tubes lifetime, reducing replacement, production interruptions and increasing reliability.

Aug 17, 2017

By Jörg Thomasberger

Delivering liquid steel to a steel processing unit at right temperature is an important criterion for high production steel shops, but it is surprising how little attention has been paid in the past to manage this vital phase in the steelmaking process-the steel in transit. The ladle running costs, both directly and indirectly, contribute significantly to the cost of steelmaking and should be an area of concern to any high production steel plant. Here we are talking not only of refractory costs or preheating fuel costs, but also cost of extra heating in ladle furnace, additional process delays incurred in delivering steel at right temperature to downstream unit in case proper care is not exercised at upstream unit, and occasional costs of ladle breakout due to inability to judge the residual life of the ladle. This paper emphasizes the need of a comprehensive ladle management system, an aspect which has not been properly addressed in the operations of a steel plant, in improving the productivity of a steel melt shop. Starting with review of present status and the attempts at implementation of ladle tracking in steel melt shop automation system, it looks at components of an exhaustive Ladle Management System (LMS), and finally gives an idea of benefits that will accrue from implementation of such a system in a steel melt shop.

Aug 17, 2017

By João Luiz do Vale

In standard wear tests, such as pin on disk (ASTM-G99) or block on ring (ASTM-G77), the apparatus simulates conditions that are often different from a machine element real application. Therefore, for an accurate investigation of a tribological application, it is essential to test the real condition in which there are similarities as: geometry, contact details, force application mode, materials, among others. It emphasizes that for studies involving polymeric materials it becomes extremely relevant. Thus, the Laboratory of Surfaces and Contact (LASC) at UTFPR developed an apparatus for sliding bearing on shaft test. In that equipment, loads are applied by a dead-weight system and the frictional force is measured on a load cell. The apparatus operating ranges for load added to the dead weight system and rotation shaft are from 0.2 to 5.0 kgf and from 260 to 3500 rpm, respectively. This paper presents a detailed evaluation of such apparatus, which includes free-body diagrams analysis and a deduction to obtain an equation for the kinetic friction coefficient. Also, the standard measurement uncertainties of a caliper, an electronic scale, and a cell load were determined. It was verified that the kinetic friction coefficient equation is dependent on the apparatus geometry, the applied load, and the frictional force value. Additionally, through the statistical significance analysis it was concluded that some terms in the equation were not significant. Finally, through the application of the error propagation theory in the kinetic friction coefficient equation, the standard measurement uncertainty of the apparatus which showed a value nearby 0.002 along the operating range of the apparatus was obtained.

Jul 31, 2018

By Werner Klein

The utilization of production facilities in an optimum way, with reliable due date fulfillment, reducing raw material and energy consumption, are challenges iron and steel companies are facing in their business every day. By using an APS system such goals can be achieved to increase the competiveness of iron and steel producers. A sophisticated APS supports the overall planning process by applying complex rules based on product and order mix, its production routings with corresponding processing and transport times and resource availability. Specific technological as well as steel grade and energy related constraints are also considered to meet company specific KPIs. A core feature of APS solution is to react online on deviations to plan during the production process. Deviations such as nonconformance of intermediate material attached to an order, sudden production delays, unavailability of important production resources, makes it necessary to update the production plan. In general the task of APS is to support the preferred work-to-order concept, by assigning work-orders to available production facilities along the product specific process route and generate optimized material sequences for critical work centers.

Aug 17, 2017

By Rudolf Lesch

Till date, coke has been produced mainly from coals with a content of volatile matters in the range of 20% to 28% and good coking properties. If such so-called "selfcoking" coals are available, blast furnace coke or foundry coke with the required quality characteristics can be produced in top-charged horizontal ovens. In this case, the possibility of using high-volatile coals and in particular coals with low-caking properties is very restricted. Even if high-volatile coking coals have good coking properties, coke produced from such coal alone will not meet the requirements in terms of coke strength. The mechanical coke properties are influenced by the charge coal blend and the coking conditions. In this context, the bulk density of the oven charge is a decisive factor. Research and development in the field of coke production in horizontal chamber ovens aims at improving the specific oven throughput, increasing the raw material basis and introducing environmental protection technologies. The key factor, however, is to guarantee and further improve the rentability of the coke production. It is very important to reduce the cost of the charge coal to a minimum at the same time maintaining or even improving the coke quality.

Aug 17, 2017

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By D. A. Aranda-Regino, C. Gómez-de-la-Garza, J. Ramírez-Cuellar, L. A. Leduc-Lezama

The Pickling Line Tandem Cold Mill (PLTCM) at Ternium’s Pesqueria plant with a 5 stands, 6 high configuration started in 2013. At the time of the start up the work roll specification and grinding practices were stablished following a low risk policy to be able to sustain any start-up associated accident. Once a stable operation has been achieved both these policies are being modified to improve productivity and reduce costs. The specified hardness of the rolls has been increased and efforts are being made to optimize the grinding according to the rolling campaign length and materials. The fatigue damage in work rolls, after rolling and its removal by grinding was followed by hardness measurements made at the end of the rolling campaign and after grinding. Softening of the rolls after rolling was found mainly in final stands to be related to the averaged stress experienced during the campaign, the original roll hardness was recovered after grinding. Hardness evolution was also followed after each grinding step finding that the total amount of grinding could be reduced. The grinding practice was modified accordingly for the first stands and the yield of work rolls in them has improved.

Oct 1, 2019

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Wolfgang Oberaigner

Primetals Technologies has always been a driver of innovation in steelmaking, especially by providing sophisticated process expert models for continuous casting machines. This capability is demonstrated by recent advancements in automation solutions that include: DynaPhase, Dynacs 3D, and DynaGap. This state-of-the-art suite of dynamic secondary cooling and soft-reduction packages take into account thermodynamic effects such as shrinkage and phase transitions, and thereby significantly contribute to direct quality improvements during the solidification phase in the continuous casting process. Speed Expert calculates an optimum casting speed for every casting situation, and additionally recommends a strand speed so that the point of final solidification is positioned at the end of a segment for optimum soft reduction. In the case of steel grade changes, the Intermix Expert precisely calculates the chemical properties of the mixed steel, thereby minimizing losses due to deviations from required specifications. The Nozzle Expert is a new model that detects clogged nozzles and broken hoses in secondary cooling systems. The first installations were highly successful and customers are pleased with impressive reductions in maintenance costs and improved steel quality. This paper describes these innovative process automation solutions and gives an overview about the successful results achieved within the first installations.

Aug 16, 2017

By Moisés Paulo Teixeira

The use of tailings for the synthesis of new materials is a worldwide concern today. This paper approaches the utilization of tailings of soapstone (steatite) in order to produce ceramics. The results show that the addition of soapstone in a ratio over 20% in the ceramic mass has enhanced the bending resistance of the ceramic samples when they were fired at temperatures of 900°C or 1000°C.

Oct 30, 2017

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Andrea Zanon

Recently steel manufacturers have significantly focused their attention on safety and working conditions thanks to new labour laws, comprehensive operators’ knowledge and increased company social responsibility. Even with a reduced budget, investments on safety are now widely approved. Mill constructors aim at developing upgraded solutions to comply with these new requirements. In some cases mill constructors can even anticipate customers’ requests and consequently put into the market innovative solutions. In this text we will analyze some advanced solutions developed by Danieli & C. Officine Meccaniche Spa - the leading company in long-product rolling mills - aimed at improving working conditions on wire-rod block settings. In particular, we will focus on rolling guides installed on fast-finishing blocks and on servo-assisted device for rolling rings changing. In fact, this equipment has shown effective benefits on our test plants and has mainly cut out the tendency of the personnel to be absent due to backache. This paper will first present standard working conditions, will then introduce the newest equipment developed by Danieli & C. Officine Meccaniche Spa, will analyze its operation and finally will describe in detail the benefits that can be reached with its use.

Jul 30, 2018

By Martim Hideki Nakayama Kurauchi

One of the main issues regarding the use of charcoal in metallurgical processes is its mechanical strength, which is much lower than coke. There is no defined standard to determine charcoal compression strength, and the methods described in the literature consist in using a prepared specimen and applying compressing load in the same direction of the charcoal fibres. As charcoal is highly anisotropic, it is proposed a procedure that does not use a specimen and with load applied on a specific direction. Instead, it intends to simulate industrial conditions by randomly dumping charcoal inside a tube, without preferential directional arrangement. This is an attempt to determine charcoal mechanical strength and predict the behaviour of bulk charcoal under a static load, as in a blast furnace. Experiments with controlled loads have been carried out on randomly distributed bulk charcoal with controlled initial size and their effect on the size distribution has been analysed. After compression, charcoal is screened and each size is weighed, determining the particle size distribution of the experiment. This method can therefore be used to evaluate charcoal mechanical strength.

Aug 1, 2018

By Claude Bodeving

The present steel economy drastically increases the financial strain on blast furnace operators. As a consequence, the importance of reliable cast floor operations is increasing drastically, which has a direct influence on the required clay mass and tapping equipment performances. When using modern high performance clay masses, pneumatic taphole drilling machines quickly reach their performance limits, which has made fully hydraulic drill hammers a standard in modern cast house operation. Besides the well-established hydraulic TMT hammers with high impact energy, an alternative version with lower impact energy, but high impact frequency was developed by TMT in the past, in order to achieve improved taphole protection. TMT’s recent research has shown that the drilling requirements inflicted by the taphole condition change over the taphole length, which has triggered the development of a new hammer, capable of switching between a high impact frequency mode and a high impact energy mode.

Aug 17, 2017