Search Documents

By S. Vorberg, J. Preussner, B. Fischer, U. Glatzel, R. Völkl, M. Wenderoth

Pt-Al-X alloys have shown good mechanical properties and adequate oxidation resistance. Starting from a promising Pt-Al-Cr alloy, the influence of Ni additions was investigated. After ageing finely dispersed precipitates are observed. Nb, Ta, Ti and Re increase strength when added as partial substitute for Al. Minor additions of B increase creep resistance and rupture time remarkably, owing to strengthening of the grain boundaries. The evolution of the alloy development programme as well as selected properties of the multi-component Pt-base alloys are presented.

Jan 1, 2006

By Sparrow G. J

The effect of polyelectrolyte flocculants on the de-watering of a tailing suspension of very fine clay was investigated.Sedimentation and filtration experiments were carried out in the labqratory to characterise the de-watering properties of the tailing. The results were used to calculate the effect of flocculant additions on the drainage and vaporation components of the de-watering of a clay suspension ponded on to a sand drainage bed.A flocculant increased the drainage rate, but decreased the volume of water that could be removed by drainage leaving more water to be lost by evaporation.The sorptivity values measured in the laboratory were used in the de-watering equation previously established for the tailing to estimate the effect of flocculant additions on the time required to de-water the suspension from 18.2 to 60 per cent solids w/w. The calculated de-watering times were found to increase or decrease depending on the volume of water removed by drainage and the prevailing evaporation rate.

Jan 1, 1980

By Rupert O. Yantz

This report, authorized under contract Number H0111403 Amendment Number One, entitled, "Exploration of Illumination Concepts for Underground Coal Mines", contains the results of an investigation of methods, procedures, and technology for providing working place lighting in underground coal mines and construction of a prototype, man portable, mine illumination system and a prototype, machine mounted, mine illumination system for use in high and low coal entries of underground coal mines.

Jan 1, 1972

By Ewan Alexander

"As human beings, we have managed risk since the dawn of the ages and have been adept at doing so. In order to survive, we hunted or gathered. If we did not take enough risk, we died. If we took much risk, we died (Fig. 1). As individuals and tribes, risk had to be optimized to maximize our chances to thrive, as individuals and as tribes.In today’s world, the risks are vastly different, but in order to thrive, these must be managed. And no industry knows this as much as mining. In fact, the International Council of Mining & Metals (ICMM) has proposed the Critical Risk Model (Fig. 2) as a means of identifying critical risk, critical controls and associated performance standards. The ICMM focuses on sustainable development performance in the mining and metals industry. It has 23 members, representing some of the largest mining companies in the world.This approach is going to help the mining industry. But it must be applied effectively, with the acknowledgment that the system alone cannot be effective. We can say this confidently, as even companies known for the strength of their risk and safety management systems continue to experience significant incidents, and, in some cases, catastrophes. Why does that happen when all safety metrics, including injury rate, are pointing in the right direction? In the view of the author, it is only when leadership, culture and systems work in complete harmony that the resilience of an organization to manage its significant risk is at an optimal level. It remains an ongoing leadership challenge to maintain that balance and the optimal mindset in the organization. So how do you maintain that special balance?Let’s start with a basic premise. Leadership, supported by simple effective systems, creates culture which creates outcomes. Everyone going home safely is an outcome, as is cost effective operations, and to achieve those outcomes efficiently, the organization must focus on the inputs. And those inputs include effective leadership, effective systems (for the purposes of this article, risk and health, safety and environment (HSE) systems), good planning, stable operations and competent workers. This article will focus on gaining maximum performance from your risk management system."

Oct 1, 2016

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By Steve Kral

As the current boom in the global mining industry rumbles on, mining companies have had to step up their efforts to replace mined reserves. Many of the majors are replacing and adding to their reserves and resources through acquisitions. This situation has allowed junior mining and exploration companies to do what they do best. They have been re-examining once uneconomic gold, copper and other metals properties with an eye to partnering with a major to develop them. And mines that have been closed for years due to poor economics are being given another look.

Jan 1, 2006

By H. Appiah

Small scale mining (SSM) has been going on for a long time in Ghana. SSM was legalized by the PNDC Law 218, 1989. Since then there have been numerous gains from the SSM industry. The SSM is organized locally by the concession owner who engages people to work for the gold which he buys. Small scale miners (SSMs) use crudely made sluices in Ghana and, therefore, their production falls below what is expected. The SSMs work in groups and not as cooperatives, as they do in Brazil and other Latin American countries. Legalization of SSM has curbed gold smuggling considerably because a gold marketing entity is available. SSM poses certain environmental problems like pollution of water bodies and soils by mercury and indiscriminate digging of pits.

Jan 1, 1998

By Alexsandro Marcio da Silva

Com o objetivo de prover informações precisas, coesas e em tempo real aos gestores da Diretoria da Usina Presidente Vargas (UPV) para a tomada de decisões, foi criado o projeto para Gestão de Indicadores de Desempenho em Tempo Real com o foco no processo produtivo e performance das áreas de Laminação (a quente e a frio), Zincagem e Folhas Metálicas. O projeto foi desenvolvido em fases, onde cada fase contemplava um determinado número de equipamentos, áreas e plantas, com visualização em drill down. Utilizando os conceitos de Data Visualization e Operational Intelligence, foi possível integrar e centralizar as informações de diversas fontes de dados, tais como, PIMS, MES, LIMS, ERP, Supervisórios, PROCOM's e entradas manuais. Padronizar as informações de controle do processo produtivo entre os gestores facilita a identificação de problemas e suas causas, e permite analisar simultaneamente várias áreas e plantas. Exibir em tempo real perdas operacionais em decorrência de desvios de processo, torna o processo de tomada de decisão mais rápido e assertivo, contribuindo para a melhoria da performance dos equipamentos, redução de riscos de falhas, e além disso aumenta a vida útil dos equipamentos e otimiza a monitoração dos processos.

Jul 30, 2018

This report has been prepared in response to a request by the Bureau of Land Management (BLM) Fairbanks Alaska District Office that the Bureau of Mines quantitatively assess the potential supply of minerals from undiscovered deposits in the White Mountains National Recreation Area (WMNRA) and the western part of the North Steese National Conservation Area (SNCA) in Alaska. The assessment will be used to assist in future land-use decision-making. Resource Management Plans (RMPs) for the WMNRA and the SNCA were approved by the BLM in 1986. These plans imposed significant restrictions on new mineral development in the two areas. The level of public concern regarding these actions, especially on the part of the mining industry, has spurred BLM to seek additional information about the potential supply of minerals from the two areas with assistance from the Bureau of Mines. The assessment focuses on an area within the WMNRA and the SNCA which has been administratively closed to mineral entry. The study area encompassed approximately 1.24 million acres and included all of the WMNRA and the western portion of the North SNCA (fig. ES-1). Three quantitative estimates of the potential supply of minerals from the study area were developed: 1) For all lands in the study area, assuming that they are open to mineral entry-the baseline analysis; 2) For those lands which have been closed to mineral entry; and 3) For eleven prospective mineral activity areas, assuming that all are open to mineral entry.

Jan 1, 1989

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By H. D. Kline

This paper describes the methods of mining and washing brown iron are in 1957 at the Sawyer mine, leased by Wayne County Mining Co., and the Fore mine, leased by Four Mining Co., both in southern Missouri; it is one of a series prepared by the Federal Bureau of Mines on mining and milling methods and costs in various districts of the United States. The Sawyer mine is in Wayne County, about 10 miles north-northeast of Williamsville (fig. 1); the Fore mine is in Howell County, about 20 miles southwest of West Plains (fig. 2). Both are open-pit mines from which the crude are was upgraded by washing and hand-sorting to produce are of grade and quality suitable for sale to operators of iron and steel furnaces. The operations described are typical of many others that produce or have produced marketable brown iron are from small sedimentary deposits, several hundred of which outcrop on the crests or hill sides of southern Missouri (fig. 3). The 1957 production of marketable brown iron are by 40 separate operations in the southern part of the State was 281,427 wet long tons, valued at $1,637,243. Production from the Sawyer mine that year was 17,000 dry long tons of washed are, and from the Fore mine, 20,816 dry long tons.

Jan 1, 1960

[This Bureau of Mines report presents results of a survey of underground mining equipment and of two demonstration programs showing the feasibility If quieting; a load-haul-dump (LHD) machine and a personnel vehicle. Typical noise levels are presented for the major machine types used in underground mines, along with estimates of the noise overexposure of miners who operate or work near these machines. General principles of noise control are explained, and the application of these principles is illustrated in the description of modifications made to the LHD machine and the personnel vehicle. The noise control package installed On the persona of vehicle lowered its noise level by 14 dBA after 4 months of operation, and inspection of the LHD machine after 2 1/2 years of operation with the modifications showed its noise level 7 dBA lower than that of the unmodified machine. Noise dosimeter measurements indicated that both machines were in compliance with Federal noise regulations for a typical shift.]

Jan 1, 1980

By Sarah Holtz Wilson, Kenneth Rossi, Carl R. Handford, David F. Tsztoo

The East Bay Municipal Utility District’s Claremont Tunnel is an 18,000-foot long water tunnel that crosses the Hayward Fault zone near Oakland, California. It was originally completed in 1929. This project involved the construction of a bypass tunnel through the fault zone, including an enlarged vault section designed to accommodate up to 8.5 feet of horizontal offset. Ground conditions encountered included sheared and crushed serpentinite and clayey fault gouge, and presented specific challenges for construction. A special excavation and support sequence used concrete-backfilled side drifts as foundations for the vault steel sets. It also allowed for a 20-foot-wide top heading and bench excavation in soft and squeezing ground conditions.

Jan 1, 2007

By D. B. Lovett

The work described in this report was directed toward identifying and devising methods to minimize the previously observed variability between working level hour exposures and the alpha particle track densities resulting on Track Etch films exposed to mine atmospheres containing radon and radon daughters. The disequilibrium between radon and its daughters was shown to directly affect this Track Etch film calibration factor. The wide range of disequilibrium states possible in mine situations amply explains the variability in the previous tests. A file of published mine atmosphere composition data was compiled and was used, along with atmospheric compositions derived from several theoretical models ref the atmospheric behavior, to evaluate the variability of several dosimeter configurations and concepts. A nonlinear, iterative regression analyse; was formulated that successfully predicted working levels to within 8 to 10% from only the alpha particle activities (Rn, RA, and RaC') data such as are obtainable from Track Etch films over a wide range of disequrlibrium conditions. A model expressing atmospheric concentrations as a function of radon source strength, plate out rate factor, ventilation rate and the fractional re-entry by recoil of previously platted-out daughters was derived and used in the regression program in addition to preparing a set of reference tables and graphs showing the disequilibrium behavior of the atmosphere. Other factors that can affect the Track Etch Film response writ considered and shown to he less crutial than the disequilibrium state. The results of a series of exposures of a dosimeter concept fixture in the Denver Mining Research Center radon chamber air presented and discussed.

Jan 1, 1976

By John C. Cook

Channel sand bodies ("wants" or "cutouts") are deposits of barren, hard sediments which interrupt production and pose safety hazards when encountered in underground coal mining. To locate these costly impediments to mining in advance, from the surface of the ground, the seismic reflection method is recommended. High-resolution (high frequency) techniques for shallow seismic exploration of coal beds have been worked out and are reported here, including a field example. Newly-developed high-frequency, digital recording equipment was used, together with light-weight shot-drilling equipment and a variety of down-hole seismic impulse sources. Techniques for rapid but complete coverage of a coal prospect area with a crew of 2 to 6 men n 2 or 3 vehicles are described in detail.

Jan 1, 1976

By G Boyd

The Nokomai Gold Mining Project commenced production in January 1992. The Project continues a history of mining in theNokomai Valley which extended from 1863 to 1942. L & M Mining Limited have held interests in the valley since 1980. In 1990 the Nokomai Joint Venture was formed with the Hore family, the owners of Nokomai Station, to mine a large alluvial gold resource in the valley. The mine is located adjacent to the Mataura Brown Trout fishery and required extensive environmental studies prior to granting of permits. The mine is budgeted to work for 20 months, processing 460 000 m3 of wash material. During this period, contract miners, Downer Mining Limited, will move in excess of seven million cubic metres of overburden from the deposit.

Jan 1, 1992

By Edward L. McHugh

The study area, which comprises 28,443 acres within the Jacumba Wilderness Study Area, is in the California Desert Conservation Area, and along the U.S.-Mexico border 25 miles west of Fl Centro, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of mining claims, known mineral occurrences, and mineralized zones during the fall of 1983. Limestone resources were identified inside the study area; tungsten resources may he present. Metasedimentary rocks intruded by Cretaceous Quartz diorite predominate in the study area. Tungsten and some gold have been found in skarn zones along intrusive contacts; limestone deposits are in the pre-Cretaceous rocks. Tertiary and Quaternary volcanic flows, pyroclastic rocks, clay beds, and diatomite in lake deposits nave been investigated for possible non-metallic resources. Evidence of mining or prospecting was found at 26 sites in or just outside the study area. In 1983, 106 claims were held in 13 claim groups. One claimant was sporadically prospecting for gold on claims in the north part of the study area in 1983, and gravel was being mined from alluvium 1/4 mile to the east.

Jan 1, 1985

By E. R. Maize

[he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, a-12 it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichw~ :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

Quickly and cheaply consolidate underground slimes to facilitate their use as backfill and permit their easy handling for other reasons. Approach: The slurry containing slimes is pumped into active stopes and electrokinetically dewatered to provide consolidated back fill. How It Works: To densify slimes electro-kinetically two electrodes are placed in the material to be dewatered and densified. Typically, the electrodes are pieces of wire mesh fencing. One is placed on the bottom, and the other is suspended in the slurry near the surface. Figure 1 is a simplified section of a test. A d-c voltage of 100 to 400 volts is applied across the slurry. This causes the solid particles which are in suspension in the water (usually these are negatively charged) to migrate toward the anode; simultaneously, the water moves toward the cathode. Water immediately adjacent to the negatively charged solid particle surfaces contains an excess of dissolved positive ions. When these ions are attracted to the electrode and move towards it, they also exert

Jan 1, 1976