Search Documents

By S. Caron, P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. However, over the last decade, Discrete Element Method (DEM) modelling has shown an interesting potential in describing the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics, and in developing solutions to industrial practice. With the objective of bringing this modelling technology into the concentrator control room to assist operators, this paper aims to describe the main elements needed to apply this emerging and developing technology to on-line mill performance monitoring.

Jan 1, 2004

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

Process Simulation and Plant Design of a Mineral Selective Magnetising Flash Roasting Plant Using Neutrons

Sep 13, 2010

By Derek Ellis

Volume II of this two-part series on Submarine Tailings Disposal (STD) as a tailings management option for coastal and island mines contains descriptions of lesser known case histories. The Misima gold mine (Papua New Guinea) and the Black Angel lead-zinc mine (Greenland) are described in some detail as the best documented cases. Atlas copper mine (The Philippines) is less fully described due to relative lack of documentation. The Misima and Atlas STD systems are working to their design criteria. At Black Angel the system adopted did not prevent contamination for a number of reasons, which are now understood. Two cases are described where STD is being developed. They are the Cayeli Bakir copper mine Turkey), and the Toquepala and Cuajone mines (Peru). There is excellent documentation available for both cases. Three case histories are described where tailings have reached the sea either through beach or river discharge. In one case the STD option has been explored (Marcopper Mine, The Philippines). In the others we explore in hindsight whether STD might have been a viable alternative using the Screening Criteria that this Volume develops - see below. The mines are Bougainville Copper Mine in Papua New Guinea, and Jordan River Mine (Canada). There is potential for STD at all three sites. Finally, the Volume presents Screening Criteria for appraising STD, based on the experience in design, operation and environmental impact reviewed in the case histories.

Jan 1, 1994

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By J. P. Piguet, A. Hosni, J. P. Josien, H. Baroudi, R. Hadadou

"The iron ore mines in the Lorraine region of north-eastern France cover a surface area of approximately 3,900 km2 and involve more than 150 cities. A total extraction method was usually used during exploitation, but this technique was sometimes replaced by the room and abandoned pillar technique when it was necessary to protect surface buildings and infrastructure. Rooms and abandoned pillars were initially designed to ensure long-term mine stability. However, this aim was not always reached and numerous collapses occurred in the Lorraine iron basin, either during production or several years after closure. Several subsidence events were identified during a period of one century; the most recent event occurred in 2012. Two groups of events were identified. The first group represents events characterized by sudden surface movement, and the second group includes event characterized by progressive subsidence.Numerous studies conducted during the last decade helped improve our understanding the origin mechanism of spontaneous or progressive (slow) events. These studies led to identifying long-term potentially unstable underground zones (hazard zones), particularly deep zones located under buildings and infrastructure. The latest are currently monitored by microseismic networks. A similar high requirement level is needed for unstable zones without taking into account the kinetics of the subsidence, which is very important for safety. Thus, GEODERIS initiated this study, primarily to acquire a better understanding of the kinetics of the progressive events group and identify the main parameters that could explain why some pillars zones developed a maximum amplitude subsidence on surface within a few hours or days, while it took several weeks to months for others. In practice, the results of this study will facilitate adapting the requirement level of microseismic monitoring system to the kinetics of pillar collapse.To retrieve the real kinetics for each event, historical and sparse documentation was used. Firstly, archives research was conducted, especially testimonies and newspaper articles published during the events. This work helped to gather useful information that sometimes contained a precise description of subsidence duration. The archives research helped to classify some progressive events according to the subsidence kinetics. Secondly, a diagnostic of geotechnical and geomechanical parameters of historic events was realized, combined with a cross analysis of the data. The analysis took into account dimensions of underground workings (e.g., pillar lengths, widths, heights, introduction of a “pillar shape factor”, and stress amount). An original expression was highlighted to connect the pillar geometry to the stress state. The kinetics expression was calibrated to classify the historic events taken into account according to the kinetics of movements. The kinetic criterion was applied to predict subsidence kinetics for the potential unstable zones currently monitored by a microseismic system."

Jan 1, 2015

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007

By J A. Rowland

When executing a ventilation change the mine ventilation circuit is in a state of flux throughout the entire change period with discrete mine areas both under ventilated and/or over ventilated during the change process. Whilst routine risk reduction strategies such as removing electrical power and people from the mine are commonly deployed it is wise to complete the change in the shortest practical time frame. This not only minimises the chance of unacceptable concentrations of contaminants accumulating around the mine but reduces the impedance on production activities which are routinely suspended during these change periods. This paper firstly highlights the importance of the maintenance of an accurate ventilation model and discusses issues which should be considered to assist to maintain in it a suitable state of health. Further it provides some tips on how to monitor that your model is in an acceptable state of tune so that it can be confidently deployed in the change process. Finally, it details the sequential process how a finely tuned and accurate ventilation model can be utilised to carry out major ventilation changes according to appliance pressure adjustments only and without the need to constantly measure and check resultant branch flows throughout the whole change process. Also discussed are some simple practical tips which will help ensure that the ventilation change process will go according to the devised plan on the day and in the most appropriate order including checking the efficiency and accuracy of the change, after it is completed.

Oct 12, 2022

By R. J. Leary

The technologies of contemporary iron and steel production and of direct reduction processes have been studied to identify and estimate the potential effects of direct reduction on mineral consumption and the problems raised thereby for the Nation's mineral supply to the iron and steel industry. Contemporary patterns of mineral raw material and energy consumption were determined from a study of the 1964-70 period. Major changes were observed in requirements for 14 of 20 principal commodities. Average practice in 1970 was compared to best practice to estimate the potential effects of implementing existing technology without recourse to direct reduction. Potential effects of direct reduction were estimated by comparing the mineral requirements for 95 percent reduced pellets with 1970 best practice technology for two cases of use: (I) complete substitution for hematite pellets in blast furnace burdens, and (11) partial substitution (40 percent) for scrap in electric furnace steel charges. Effects upon mineral supplies are described; important collateral factors are analyzed, and the principal metallurgical, industrial, and environmental consequences of implementing direct reduction are discussed. Major effects of direct reduction on the domestic steel industry and its mineral supply system are foreseeable. Direct reduction will (1) create a large demand for low-gangue iron ore; (2) relieve the dependence of the steel industry on coking coal, and (3) permit great increases in furnace productivity, both in blast furnace ironmaking and electric arc furnace steelmaking.

Jan 1, 1973

By M. H. Moys, J. A. Finch, A. R. Laplante

"A detailed review of ball milling circuit control practices in industry has been carried out. Based on fundamental process performance objectives, a standard system for base-level control of most ball mill installations is presented. This system is simple, inexpensive, and provides the major economic benefits available from contemporary automatic control technology.Value Analysis of Grinding OperationsValue analysis (or engineering, or management), originally developed by Lawrence D. Miles of the General Electric Company (1), focuses on the identification of value (product or process worth versus cost) and provides a systematic procedure for its improvement. A recent research and development project involving the application of the principles of value engineering to grinding operations has provided a basic technoeconomic model of grinding processes (2). The functional objectives of the ball milling process and the means to achieve value based grinding circuit control originate from this study.The Need for Grinding Circuit ControlThe economic effectiveness of a process is determined by the quality or value of the product and the related processing costs. If the inputs (both the raw feed and the applied processing work) are absolutely constant, the product characteristics and the process efficiency will be determined only by the engineering design. The need for and degree of process control is therefore determined by the nature of variations or upsets in the process inputs, and the extent to which these effect product value and operating costs."

Jan 1, 1988

By A Weston

Northparkes Mines is a joint venture between Rio Tinto and the Sumitomo group and is operated by Rio Tinto to produce copper concentrate from ore sourced from open cut and underground. Underground ore is mined with an owner operator workforce using the block cave method from the E26 deposit, with the first lift of the cave now completed. Development of the Lift 2 block cave commenced in March 2001 using a contract workforce. The Lift 2 Project required the mining of 14 700 m of decline and lateral development to establish a new mining horizon at the 9450 level and to develop two new conveyor declines. Also included in the scope was the excavation of a Crusher chamber to house the jaw-gyratory crusher. This paper describes the excavation of the hydroset chamber and orepass that sit immediately underneath the Lift 2 Crusher chamber. It includes risk assessment, planning, development of method statements and standard operating procedures, through to the excavation of the orepass and the installation of ground support in seismically active ground. There was a major ground failure in the backs of the conveyor feeder chamber during its excavation, which affected the excavation of the orepass due to its proximity to the breakthrough site.

Jan 1, 2005

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

Fine coal is defined as material with a maximum size of 1/2 in. Various methods for separate washing of such coal are discussed briefly because separate treatment can lead to a higher overall recovery of coal or to a product having a lower ash content.A felspar jig is discussed in detail because it is the method most recently adopted in Australia, and because it has the advantages of compactness, flexibility and automatic Gontrol, with minimum operator attention. This jig has a variety of adjustable controls to enable the desired results to be obtained from a wide range of coals and the general application of each control is discussed.The only separate treatment of fine coal in the Illawarra district is by felspar jigs on Bulli seam coal.INTRODUCTIONAll reasonably large Australian collieries now win coal by mechanical methods. but while mechanization leads to more economic production of high tonnages, it also changes the characteristics of the coal won. In particular there is an increased proportion of fines, and an increased ash and moisture content. However, specifications of coal for sale have become more stringent, and consumers now require coals in a definite size range with a lower and more uniform ash content, as well as with a low and uniform moisturecontent.These factors have led to the need to wash and grade run-of-mine coal at the pithead. In' plants where the whole of the run-of-mine coal is treated in a jig, some of the fine coal in the feed is beneficiated; the extent depending on factors such as the type of coal and the feed rate. However, for dense medium treatment, fine coal must first be screened out, and there may then be no washing of fine coal at all.

Jan 1, 1961

By Z. Zhang

The author recently has reviewed the publications on the slag-related research in China since the Sixth International Conference on Molten Slags, Fluxes and Salts in June, 2000. In fundamental aspects, the physical property predictions and measurements, slag-metal reactions, slag-refractory reactions have received close attention, and are briefly described here in this report. More than half of slag-related publications deal with plant investigations due to the requirement of technological improvements and environmental protection. In the present paper, the research on slags in various treatments related to clean steel production and the utilization of the waste slags is briefly reviewed.

Jan 1, 2004

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By Giovanna Valdivia Málaga

Dado que la comunidad de Michiquillay recibe una gran cantidad del canon minero a través de la gestión de la Municipalidad del mismo nombre, se planteó mejorar las relaciones de parentesco y la inmersión en la modernidad económica y socia de dicha comunidad y pasar de una economía informal a una economía social o solidaria. En ese sentido, el presente texto describe el proyecto de participación colectiva entre los miembros de la comunidad Michiquilllay y La Encañada, con el objetivo de construir una propuesta de privatización del proyecto minero Michicallay. El trabajo de campo se realizó en los ocho sectores y se desarrolló desde hace dos años, alcanzando la comunicación y sostenibilidad del mismo.

Sep 12, 2011

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By W. G. Payne, A. C. Richardson, B. L. Gandrud

"INTRODUCTION The Connellsville mine of the Yolande Coal & Coke Co. is in the southwestern part of Jefferson County, Ala., about 30 miles southwest of Birmingham. The mine is on the Blue Creek bed, which is about 6 feet thick and dips at a angle of 18º. The bed is worked by the room-and-pillar method and is mined by both machine and hand methods. The Blue Creek bed at this point yields a high ash, low-volatile coal with excellent coking properties. Because of its exceptionally low volatile content and high coking strength, this coal is excellent for blending with Alabama coals of higher volatile content and weaker coking properties to form blends suitable for production of metallurgical coke.A sample of washed coal taken during this investigation gave the following analysis on an as received"" basis: Moisture, 8.3 per cent; volatile matter-, 20.2 per cent; ash, 8.0 per cent; fixed carbon, 63.5 per cent. The high ash content of this coal limits the quantity which can be utilized when low-ash coke is required. In the Birmingham district it is usually difficult to sell as coking coal a product that contains more than 8.0 per cent ash. To produce a. coal with this ash content at Connellsville presents a somewhat difficult washing problem. This paper gives the results of an investigation that was conducted by the Southern Experiment Station of the U. S. Bureau of Mines in cooperation with the University of Alabama and the Yolane Coal & Coke Co. for the purpose of determining the washing characteristics of the coal and the possibility of reducing its ash content on coal-washing tables.The practice at the Connellsville washery at the time of beginning this investigation was to crush the run-of-mine coal to pass a 1 1/2-inch round-hole screen and to treat the satire output on two primary, 3-compartment jigs. A. middling product was recovered from the primary jigs which was re-treated on a single-compartment rougher jig. This system yields a product of acceptable ash content, but the yield is low and the loss of good coal in the refuse is high."

Feb 1, 1933