Search Documents

By Ben Murphy, Tomi Maksimainen, Antti Rinne, Ishmael Muzinda, Toni Mattsson

"A 500m3 flotation cell was commissioned during 2014 at the Kevitsa Mine in northern Finland working as the first rougher in the copper flotation circuit. Treating around 850tph with an average grade of 0.3% Cu, the TankCell® e500 has run with an average copper recovery of 71% and an average enrichment ratio of 50 during early optimization test work. In addition the cell has proved to be very energy efficient, being operating with a specific energy of around 0.4kW/m3 under production conditions.A review of the installation and operation of the TankCell® e500 at Kevitsa will be presented. Metallurgical performance of the cell during the operating period will be discussed on the basis of on-line analysis and the metallurgical samples collected during early optimization campaigns.IntroductionThe past three decades have seen a rapid increase in the size of mechanical flotation cells. This has been largely driven by demand from the copper industry to process larger volumes of material due to combination of declining head grades and the desire to benefit from the economies of scale (Lynch, Harbort and Nelson 2010). During this period Outotec has been at the forefront of development of large flotation technology with an enviable scale-up track record; 100m3 (1995), 160m3 (1997), 200m3 (2002), 300m3 (2007), 500m3 (2012) to the largest commercially available cell at 630m3 in 2013. This scale-up methodology has been developed, tested and validated (Elgueta et al., 2009; Coleman & Dixon, 2010) by the large installation base of cells in the 300m3 size class operating (over 400). The learning from large cell operation are then reviewed and incorporated back into new designs and scale-up practices (Murphy, Miettinen, and Yanez, 2014)."

Jan 1, 2016

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

By J. A. Finch, Zhenghe Xu

The competitive adsorption of xanthates on sulphide minerals in a binary mineral system (pentlandite and pyrrhotite) was studied using the pseudo-in-situ technique of attenuated total-reflectance FTIR spectroscopy. The minerals were placed in the same collector solutions, either separated by a glass wall or in direct contact with each other before magnetic separation and separate analysis. The effect of mineral interaction on xanthate adsorption was clearly demonstrated spectroscopically for the first time. At low concentrations of xanthate, its adsorption on pentlandite was activated by physical contact with pyrrhotite; the effect may be attributed to the enhancement of electron transfer through electrical contact between the two minerals. The results emphasise the need for caution in extrapolating results obtained from single-mineral studies to flotation practice

Jun 18, 1905

By C. Gherghel

The planning and operation of ventilation network systems for uranium mines require special considerations since ventilation is the primary technique of controlling ambient concentrations of radon progeny. The major environmental challenge facing the ventilation engineer is the requirement to dilute radon progeny to below the Working Level Month per year of worker exposure required by law. The application of large airflow volumes and the utilization of low residence times constitute some of the factors considered by the design engineer. Good mine planning and sequencing are also critical for protecting the health of miners. The mine ventilation must have such characteristics as flexibility, high air distribution efficiency, rapid air transit times, zero recirculation and no short-circuiting. A well established maintenance program for all ventilation appliances must be in place to guarantee control of the distribution system. Real-time monitoring systems permit assurance the adequate quality of air is delivered to working places. A case study for an operating mine is used to demonstrate how the ventilation system is successfully managed and operated using the above concepts.

Jan 1, 2009

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

"INTRODUCTION AND ACKNOWLEDGMENTSAt the request of the lessees, the Pearl tract was examined in February 1946, by Otto Ruhl, an engineer of the Bureau of Mines. From the evidence of old drill logs and from the few available records of mining operations on the Pearl and the adjoining Trussel (Big Tom) tract, it appeared that a relatively small churn-drilling program might develop enough lead-since ore to justify resumption of mining. In March 1946, funds were allotted for churn drilling, and the work was begun the following month. Ten holes totaling 1,933 feet were completed before the close of the project in August 1946. The work was under the general supervision of C. H. Johnson, chief, Rolla Division, Mining Branch, and under the direct supervision of the Bureau project engineers. 3/In its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to our national security and economy, It is the,of the Bureau to publish the facts development by each project as soon as possible after its conclusion. The Mining Branch, Lowell B. Moon, chief, makes preliminary examinations and conducts investigation of mineral deposits. The Metallurgical Branch, O. C. Ralston, chief, participates in this program by making beneficiation tests and analyses. In the present project, no metallurgical tests were made, and for the sake of speed the samples taken were analyzed by a local commercial assayer. 4/"

Jul 1, 1947

By Mary Ellen Large

This publication of Deep Foundations Institute (DFI) is intended to provide project owners, design engineers and construction professionals with guidelines for selecting cutoff wall and barrier systems and a general introduction to their methods of construction. Three categories of cutoff wall and barrier construction technology (excavated cutoff systems, in situ techniques, and driven cutoff systems) are presented and parameters for evaluating their design and construction are discussed. The information presented was compiled from the opinions of practicing engineers and construction specialists from the DFI Slurry Wall Committee.

Jan 1, 2021

By Zhan Jing

Keywords: thermodynamic, Ni-Co alloy powders, composition, fibrous The mathematics model of Ni(II)-Co(II)-C2O42?-NH3?H2O-H2O of thermodynamic equilibrium system has been developed theoretically according to the law of conservation of mass and the law of simultaneous equilibrium, and the logarithm concentration-pH (log[Me2+]T-pH) diagrams of this system have been made. The effect of ligand and pH value was studied. Two issues in coprecipitation route to synthesize fibrous nickel-cobalt alloy precursor powder, com-position and morphology which are a first priority, are addressed based on thermodynamic analysis and experiments. The results show that suitable pH value range of coprecipitation of nickel ions and cobalt ions in theory can be obtained to maintain fibrous, excellent compositonal homogeneity and stoichiometry in coprecipitation products. Experimental demonstration is also carried out.

Jan 1, 2005

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Hessam Yazdani

In comparison to the conventional piled foundations, the piled-raft foundations provide a more economical solution to support high-rise buildings constructed on soft soils. In this type of foundations, the bearing capacity of the underlying soil is taken into account to support the superstructure loads and the piles are placed to control both the total and differential settlements of the superstructure. Currently, there is not a standard and worldwide acceptable approach to select the location of the piles and most of piled-raft foundations are designed based on the experience of designers. Therefore, particular attention should be given to the optimal design of this type of foundations in order to minimize the considerable construction costs involved. This paper examines the capability of the ant colony optimization (ACO) algorithm to optimize the piled-raft foundations subjected to static and seismic loadings. The soil-pile interaction is considered by modeling the side and tip resistance components of the piles using the nonlinear Winkler-based p-y and t-z curves in the OpenSees program. The soil-raft interaction is taken into consideration using the Winkler springs beneath the raft. The objective of the optimization problem is to minimize the construction cost of the foundation by taking the configuration and number of the piles as design variables. The side and tip forces of the piles as well as the total and differential settlements of the foundation under the serviceability limit state are considered as the constraints for the optimization problem. Results show that in addition to the type of analysis (linear/nonlinear), the regard or disregard of the soil-pile interaction in the analysis can significantly change the optimal solution. The optimal solutions obtained match the engineering expectations and indicate the effectiveness and capability of the ACO algorithm to minimize the construction cost.

Jan 1, 2013

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

Overcasts are indispensible ventilation control devices to permit one airway to pass over another without mixing in room and pillar coal mining. The airflow distribution inside the overcast depends on its spe-cific configuration at which the flow enters into it. This study uses 3D numerical simulation to examine the pressure and velocity distributions inside an overcast. The effects of the overcast angle on the flow field are also examined. The flow is assumed to be turbulent and isothermal and the standard k-e model is utilized. Simulated results display flow separation and recirculation regions of different sizes occurring not only upstream and downstream from the overcast but also inside it. The results also show that the size of the recirculation regions in-creased with the increase in the angle before and after the overcast influencing significantly the flow field and pressure losses. The stream-lines are plotted to show the 3D structure of the flow field. The results from the simulation can guide overcast design commonly used in un-derground coal mines. Keywords: 3-D simulation, Overcast, Room and Pillar, Turbulence, Recirculation Region

Feb 27, 2013

By Jeffrey Johnson, Carl Sunderman, Ted Williams, Stephen Signer, Douglas Bayer

To measure the loading behavior of friction bolts, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) installed strain gauges on the interior of friction bolts and developed a battery-powered miniature data acquisition system (MIDAS) that fits inside the hollow portion of the friction bolt. The advantages of this system are that it is protected from face blasts and eliminates the need for external wiring. Laboratory pull-out tests showed that friction bolts installed in a concrete block with resin were loaded to about 1.8 tons/ft of bolt length; bolts installed without resin were loaded to 1.3 tons/ft. Three strain-gauged friction bolts were installed at Hecla Mining Company’s Gold Hunter Mine, Mullan, ID, in the wall or rib of a mechanized cut-and-fill stope. The object of these tests was to establish an installation procedure for the bolt-and-MIDAS combination and to evaluate performance. The stope was advanced in three 15-ft increments and strains induced in the rock bolts by stress changes in the rock were recorded every 30 minutes. The MIDAS proved to be rugged enough to withstand the shock and vibration from nearby (5 ft) face blasting. Data from MIDAS showed that the friction bolt installed with resin was the most sensitive to each face advance. It showed a steady increase in loading to a maximum value of 1000 microstrain. The friction bolt installed without resin showed stick-slip behavior with loads to a maximum of 400 microstrain before the stope was completed.

By C. V. Corless

1. Introductory Some members may recall that at the Annual Meeting two years ago I read a paper, &apos;The Future of the Mining Industry in Canada." Discussing this large subject it was possible only to outline the facts and inferences leading to ?the conclusion that Canada is a country endowed with enormous mineral wealth, of which the fringes are yet scarcely touched. In the present paper, I wish to examine in somewhat fuller detail the evidence, both direct and inferential, concerning the mineral wealth of the greatest physical and geological feature of Canada-the Precambrian Shield. Many, if not most, of these facts are already familiar to you. But, since they will form the basis of the reasoning employed, they will be recalled for explicit reference. First, let us review very briefly the position and extent of the Shield. The area of the entire Shield is given in textbooks as 2,000,000 square miles, of which perhaps 10 or 12 per cent. is exposed in the south-easterly part of Canada&apos;s Arctic islands. The remainder occupies roughly two-thirds of the North-west Territory; the north-east corner of Alberta; one-third of Saskatchewan ;two-thirds of Manitoba; three-fourths of Ontario; and nearly ninety-five per cent. of Quebec.

Jan 1, 1924

By D Cumming-Potvin, S W. Jacobsz and E Kearsley, J Wesseloo

This paper describes a physical modelling program that recreated block cave propagation in a geotechnical centrifuge. A brief description of the design of the test along with the sample material and monitoring equipment is given. The samples tested showed caving behaviour and fragmentation distributions that one would expect from caving mines, with one cave deviating due to pre-existing major discontinuities in the sample. A series of fractures formed ahead of and parallel to the cave, implying that an extensional failure mechanism may play a larger role in cave development than previously thought. The results of acoustic emission monitoring of the tests show a seismogenic zone advancing ahead of the cave; however, the quantity and quality of the data is too limited to draw any further conclusions.CITATION:Cumming-Potvin, D, Wesseloo, J, Jacobsz, S W and Kearsley, E, 2016. Results from physical models of block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 329–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Y Xie, L O’Connor, S C. Dominy

Sheeted vein gold deposits are characterised by multiple subparallel veins and often free milling gold. Variability in gold grade and recovery parameters are enhanced by poorly designed sampling and test work protocols. Poor quality samples generally equate to an enhanced nugget effect. A sample can be described as being representative when it results in acceptable levels of bias and precision. Total sampling variability can be quantified by the relative sampling variance, which measures the total empirical sampling variance influenced by the heterogeneity of the lot being sampled under the current sampling / test work protocol. Effort should be made to minimise the relative sampling variance through Theory of Sampling (TOS) and quality assurance / quality control (QA/QC) application. This contribution reports on a case study that exemplifies how high-quality grade and recovery data can be gained from a well-designed and planned drilling, sampling and test work program, followed by bulk sampling. Results across historical resource drilling, geometallurgical drilling, laboratory assay / test work, geometallurgical modelling and a bulk sampling/pilot processing study are reconciled. A whole core, entire-sample test work protocol was used to acquire fit-for-purpose gold grade and recovery data for inclusion into a Pre Feasibility Study reported in accordance with the JORC Code.CITATION:Dominy, S C, O’Connor, L, Xie, Y and Glass, H J, 2017. Geometallurgical sampling protocol validation by bulk sampling in a sheeted vein gold deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 185–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By S Jephcott

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists of a mineralised bituminous shale sequence containing some tuffites, numerous graded beds and isolated slump breccia horizons. The principal sulfides; pyrite, sphalerite and galena, are essentially restricted to the shales and the genetically unrelated turbidites contain only minor mineralisation. The geochemistry of the deposit has been investigated with respect to the stratigraphic column and mineralogy of the sediments. A sedimentary origin is advocated for the deposit. Volcanism, thermal spring activity and high salinities, perhaps related to the Emu Fault, are considered as contributing factors to ore genesis. The metallurgy of this deposit is discussed in relation to its geologic history.

Jan 1, 1971