Search Documents

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By David R. Beadman

The Fleming method is widely used for the analysis and prediction of single pile behaviour under maintained loading. The method does not distinguish between bored and driven piles. Driven piling avoids the need to dispose of spoil from the pile installation and is therefore becoming increasingly attractive. This paper considers the theoretical effects of the possible preload at the base of a driven pile after installation, using the hyperbolic functions as defined by Fleming. The Fleming method is reviewed and the equations and analyses are adapted, using spreadsheets, to allow for a possible preload. The simplifying assumption of the effect of the elastic compression of the pile is also reviewed and a more analytical method adopted to assess the elastic compression. Some driven pile test data is analysed to consider the possible effects of the preload on the performance of a driven pile and to test the theoretical relationships that are developed in the paper.

Jan 1, 2006

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966

By C. Sawmliana, P. Pal Roy

Near-field blast vibration response of restrained pipelines either buried or exposed was studied during rock excavations at sensitive locations for Stage-II (4x500 MW) commissioning work in a super thermal powerplant of the National Thermal Power Corporation Ltd. (NTPC) of India. The existing running plant of capacity 1000 MW has many important installations including pipelines of varying diameters. These pipelines were very close to the blasting locations (mostly within 12m). Blast optimization and consequent monitoring of vibrations were carried out simultaneously for more than 250 experimental blasts conducted by the authors. This paper emphasized, particularly, on the safety of pipelines and their responses due to repeated blasting impacts. A few guidelines supported by theoretical derivations are provided for futuristic research.

Jan 1, 2001

By P. Jurovcik, D. Yantek, D. Ingram

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5-9 dB at the operator’s left ear and 2-5 dB at the operator’s right ear while hammer-drilling. This paper will briefly discuss the preliminary design of a cab and the testing of materials for construction of the prototype. Explanation of the ideas behind the prototype design and fabrication will be covered. Finally, the field test method and results will be discussed in detail.

Jan 1, 2007

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

By V. Labiouse, B. Heidenreich

The rebound phenomenon, which occurs during rockfalls when a rock block impacts with a slope surface, is influenced by several parameters related not only to the slope material but also to the block and the kinematics. The paper presents a small-scale testing campaign undertaken at the LMR (EPFL) to better understand and quantify the bouncing of blocks on granular slopes. The influence of some factors related to the ground material, the block and the kinematics is examined. Bei Steinschlägen wird die Flugbahn eines stürzenden Felsbrockens maßgeblich durch den Abprall vom Hang bestimmt. Der Rückprall hängt von verschiedenen Parametern ab, wobei nicht nur das Hangmaterial sondern auch Blockeigenschaften und Kinematik eine große Rolle spielen. Zum besseren Verständnis dieses Phänomens und seiner Quantifizierung werden am LMR (EPFL) kleinmaßstäbliche Versuchskampagnen auf granulären Materialien durchgeführt. Der vorliegende Artikel stellt die Versuche vor und untersucht den Einfluss verschiedener Boden-, Block- und kinematischer Parameter. Le phénomène de rebond qui se présente lors de l’impact d’un bloc rocheux sur la surface d’un versant dépend non seulement des caractéristiques du terrain, mais aussi de facteurs relatifs au bloc et à la cinématique. L’article présente une campagne d’essais sur modèle réduit entreprise au LMR (EPFL) afin de mieux comprendre et quantifier l’impact de blocs sur des matériaux granulaires. L’influence de divers paramètres relatifs au sol, au bloc et à la cinématique est mise en évidence.

Jan 1, 2003

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules, under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and. tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment.

Jan 1, 1937

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By Thys B. Johnson

Operations Research techniques for determining optimal shipping schedules and production and product allocation are discussed. A hypothetical mining operation model is formulated by the Bureau of Mines, and optimal production and product allocation are determined. The technique of sensitivity analysis is discussed and is used to illustrate the effect of the variability in a mining operation on the optimal production and product market plan.

Jan 1, 1969

By John A. Breslin

The year 2010 will mark the 100th anniversary of the beginning of the research efforts by the U.S. government to improve the health and safety of miners working in the United States. This research began in 1910 with the establishment of the U.S. Bureau of Mines (the Bureau) and it has continued during the past 10 decades, even after the closure of the Bureau in 1996. The research on safer mining technology, formerly done by the Bureau, has now been combined with National Institute for Occupational Safety and Health (NIOSH) studies of miners? health to form a unified federal research program to improve the health and safety of miners. This article describes this research and places some of the accomplishments into perspective with other activities in the U.S. Mine Safety and Health Time Line (insert).

Jan 1, 2010

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

By G. L. Anderson

The critical importance of wire rope integrity to the mining industry has led to the creation of standards for the retirement of wire rope as well as to the development of electromagnetic devices and procedures that would allow wire ropes to be tested against these standards without destroying them, The U.S. Bureau of Mines (USBM) conducted research to evaluate these devices by measuring loss of metallic cross-sectional area and the number of wire breaks, or local faults. The intent was to define the extent to which the technique can identify degradation within the rope, e.g., broken wires, corrosion, and wear. Experimental results showed that instrument sensitivity depended on a number of factors, including rope diameter, placement of sensors, location and characteristics of flaws, rope speed, and tension on the rope. The experiments also demonstrated the importance of having an elongated recorder trace and a properly trained and experienced operator to interpret overall results. A design of a rope and test procedures for use in laboratory evaluation of instruments have been recommended by the American Society for Testing and Materials Committee E07.07.10, Wire Rope Applications. The USBM is working through this committee to develop standards for an electro-magnetic method of wire rope inspection.

Jan 1, 2010

By G Gosson

An important requirement in every geological quality control program is that the identity and grades of the control samples (duplicates, certified reference materials (CRMs), and blanks) must remain æblindÆ to the analytical laboratory. Once the entity to be controlled is aware of relevant details of the control process, such as the identity of the control samples, the objectivity may be lost and the control may no longer be completely valid. Whereas the blind insertion of field duplicates and coarse blanks can be easily conducted at site, simultaneously with the sampling process, the rest of the control samples should be inserted into the batches during or after sample preparation and prior to assaying, in order to ensure a proper assessment of precision, accuracy and assay contamination, independent of the internal quality control of the laboratory. Such a procedure raises the concern that blind insertion of crushed or pulverised material in sample batches prior to assaying could represent a breach in the chain of custody principle, as samples would have to be temporarily returned to the custody of a non-laboratory person in charge of the insertions. In this seemingly conflict scenario, what should we give up? Do we maintain the strict chain of custody, knowing that the laboratory will be aware of the identity of some of the control samples, or that some duplicates will not be true same-batch duplicates? Do we ignore chain of custody issues to maintain the anonymity of the control samples and insert blind same-batch duplicates, CRMs and blanks? Is it possible to do blind insertions without breaching the chain of custody? Current NI 43-101 and JORC requirements, as well as real-world QA/QC and sample security practices, are discussed in light of AMECÆs approach to the solution of this apparent dilemma.

Jan 1, 2008

Traditional loading systems have relied for many years on wheel and track loaders, power shovels, conveyor belts, and more recently, hydraulic front shovels. Each has certain advantages and disadvantages, depending largely on job conditions. Hydraulic backhoes were introduced several years ago as still another truck loading option. At first, buckets were small and backhoe use was limited to small earthmoving projects. Now, as backhoes are equipped with shorter sticks and bigger buckets to move larger quantities of earth. The "mass excavation" concept offers an excellent truck loading option in many situations. System Development and Advantages Mass excavation was first used successfully by contractors in site development and highway construction, loading both on-highway and off-highway trucks. Operators were able to take advantage of the excavator's ability to work in poor underfoot conditions and dig in tough materials. The technique was first applied to mining in the kaolin mines of central Georgia. Kaolin, one of the world's most abundant minerals, is used to make paper, paint, ceramics, rubber, plastics, and many other products. Since kaolin clay is slippery when wet, load-out with wheel loaders is very inefficient. Also, kaolin is found in very spotty deposits due to the weathering process involved in its formation. Consequently, draglines are also impractical for kaolin mining since they don't have the mobility to move between clay deposits. In response to these mining conditions and kaolin characteristics, mines began using excavators in mass excavation as early as 1976. They have developed a system that takes advantage of the excavator's •high penetration and breakout force in tight materials; •fast-cycling hydraulics; •ability to work in poor underfoot conditions; and •mobility in comparison to draglines. This loading method has been successful in Georgia's kaolin mines and now can be applied to other mining operations as well. The excavator's ability to carefully dig spotty ore deposits is an asset at uranium mining operations. Any mine can take ad-

Jan 3, 1982