Search Documents

By S. Agarwal, S. Frimpong

The creation and maintenance of a healthy working environment in surface mining operations require sustained efforts in pursuing advanced research initiatives toward the development and deployment of powered haulage technologies. This paper contains progress summary on a frontier research in truck dynamic control, vision and collision avoidance. This research is required to provide solutions to challenging problems regarding operator visibility in truck haulage in a surface mining environment. The paper focuses on truck control kinematics and dynamics, truck-haul road interactions, intelligent truck sensing, intelligent truck collision avoidance system, integrated system for situational awareness, augmented visualization and operator interface, and field testing and error variance modeling of developed technologies. A sensor suite of four subsystems, including front-side stereo-camera, front-side Doppler radar, close range sonar proximity sensors, and rear-side camera system have been recommended for developing a 360° truck operator vision to allow safe operations. This research initiative is significant because it will provide a strong basis for developing technologies to improve truck haulage safety in surface mines and construction sites.

Jan 1, 2007

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-Si02 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [m(Mgo)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, m(Fe)/m(SiO2) is 1.1-1.4 and the temperatures are within 1473?1773K, the slag viscosities increased with the increase of m(Mgo) and m(Fe)/m(sio,). When m(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When m(Mgo» 10%, the temperature should be kept above 1633K. When the content of MgO is higher, a lower viscosity slag ean be produced by decreasing the ratio of m(Fe)/m(sio,). The appropriate ratio of m(Fe)/m(sio,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made before the turn of the century, used Moissen&apos;s pyrophoric manganese.3/ This material was made by electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968

By Maurizio Siepi, Stefano Trevisani, Pagliaccim Federico, Daniele Vanni

"Abstract: The paper describes a large innovative project completed in 2012-20123 by Trevi Group, to develop equipment capable to install ultra-deep diaphragm wall. The project highlights the capacity of SOILMEC to design and build a new hydromill able to reach an unprecedented depth of 250 m, including new devices for monitoring and correct the verticality. The entire project can take advantage of the long and solid experience matured by Trevi and Rodio (now part of Trevi Group), developing in house or, else, select the elements necessary for a high quality product in the ground.The paper describes the results of different systems used to monitor and control the verticality and the twist of panel during excavation, together with the method used to pour concrete. Finally, the results of verification coring and lab tests on concrete samples recovered at various depths are discussed. The test field has been supervised by representatives of three of the major Italian Universities, and lasts almost one year from August 2012 to June 2013.The verification holes made use of an innovative combination of directional drilling and coring, to check the quality of the plastic concrete for the full length of the panel. The data confirmed that the test panel has high quality concrete, meeting or exceeding to the prefixed requirements.With this test, super-deep cut-off walls reaching depths of 250 m have become a reality. This would change the perspectives of dam engineering both for existing dams rehabilitation and for new dams design and construction. With the execution of this test panel, the technology of milled concrete cutoffs has made a ”quantum leap”, pushing the limit of practicable dams."

Jan 1, 2014

By Joan Weinberg

Seasonally adjusted new factory orders for primary metals declined in January, February, and March, especially in the steel industry. The decline was part of an apparent slowdown for the entire manufacturing sector. Orders for all durable goods, including not only primary metals, but also clay, glass, and stone products, fabricated metal products, machinery, and transportation equipment, fell in January and February. In March, orders rose a slight 0.8%. According to the U.S. Department of Commerce, the downturns in durable goods orders in January and February were the first back-to-back declines in 3 years. They were largely attributed to a drop in orders for transportation equipment, mainly auto-mobiles and aircraft, while the small gain in March was due to a surge in aircraft orders. Higher interest rates may be partly responsible for the slowdown in durable goods orders over the past 3 months. The higher rates have also hit the construction industry--another major end-user of minerals. Construction of new homes and apartments fell by a seasonally adjusted annual rate of 5.4% in March, following a 12% decline in February.

Jan 1, 1989

By D. W. Taylor, I. W. Farmer, N. Mojtabai

Rittinger's and Bond's descriptions of rock crushing relate the energy input required to fracture rock and the surface energy required to form new fractures to the change in specific surface area of feed and product during comminution. The potential applicability of this approach to blasting is illustrated, using the results of data from bench blasting tests on Pinal schists and production blasting of Carboniferous limestones. The approach contributes to understanding of the mechanisms involved in blasting and to the design of test blasts. A modified form is presented of the relationship between blasting energy, specific surface area of the muckpile and a rock energy constant related to the discontinuity structure of the rock. The modified equation fits observed data and offers a simple basis for further experiments

Jun 19, 1905

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

By M. Moys

The use of temperature measurements for unusual applications in the analysis and control of column flotation and milling is discussed. This is followed by a review of some of the authors current research in the application of the discrete element method to the modelling of particulate processes, specifically milling, fluidized beds and chute flow.

Jan 1, 2005

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By Anil Bhandari

Using subsurface data collected at each drilled shaft location is an ideal approach for conducting drilled shaft design. However, conducting subsurface tests at each drilled shaft location and subsequently performing the drilled shaft design can be a daunting task for a noise barrier wall that is divided into six (6) sections and stretches for approximately four (4) miles. In addition, having individual drilled shaft designs complicates the construction process. Grouping the subsurface conditions into broad categories and performing the design for each of those categories is an attractive alternative to the design per boring approach. Currently there are no existing guidelines to aid a designer on grouping the subsurface conditions for the drilled shaft design for the noise barrier walls. Therefore, a method was developed based on the Standard Penetration Test (SPT) N values of the near surface soils to categorize the soil profiles into distinct categories. Since the soil engineering properties of the near surface soils are known to be critical for drilled shaft lateral capacity, these soils were emphasized in the methodology. This method was successfully implemented for the design of drilled shafts supporting the noise barrier walls along the I-20 in Columbia, SC. For this project, two distinct soil profiles, labeled as ?strong? and ?weak?, were used. An overview of the soil profile grouping methodology is presented as well as the vertical and lateral drilled shaft capacity analyses for this project for the two general soil profiles. The analyses indicated that the axial capacity governed the design in the ?weak? soil profile and the lateral capacity controlled the design in the ?strong? soil profile. However, this is not a generalization and whether the axial or the lateral capacity governs the design of drilled shaft depends on the soil profile and design loads. Nonetheless, our findings emphasize that both lateral and axial capacity should be checked for drilled shaft design even when the vertical load are minor.

Jan 1, 2011

By Yves Breau, François Robichaud, Jacques McMullen, Pierre Pelletie

"The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.INTRODUCTIONThe East-Malartic mill is located close to the town of Malartic in North Western Quebec, Canada. The mill was first commissioned in 1938. The flowsheet at that time was a straight cyanidation circuit. The original mill operated in that mode up to the discovery of the Bousquet 2 orebody in 1989 which consisted of a massive copper sulphide ore averaging 0.7% copper and 7 g/mt of gold. Bousquet 2 ore processing required a mill retrofit. Grinding capacity, gravity and copper flotation circuits were inserted prior to the cyanidation circuit in order to achieve 3,200 mtpd capacity at expected recoveries.In 1993, control of the flotation circuit was deemed critical in order to maintain the flotation performance and to reduce cyanide consumption since the copper sulphide contained in the Bousquet 2 ore is a high cyanide consumer (50% bornite). (McMullen, 1999) As a result, the implementation of advanced control strategies in order to increase the metallurgical profitability of the plant and to reduce the operating variability between operators was the most rational alternative. In 1994, Corem was chosen to perform the plant audit and to write the first set of rules. The on-line control strategy was started up in 1995. In 1996 and 1997 the Expert System was shutdown because of an extreme change in the ore coming from the milling of Bousquet #1 ore and the departure of the projects engineer. In 1998, the system was restarted and the results were impressive. Furthermore in May of 2001 a patent was issued for the control strategy. (Breau, 2001)"

Jan 1, 2002

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By Mohammed Sakr

The use of helical piles for permanent foundation applications has become a practical and feasible alternative to the traditional cast-in-place concrete or driven steel piles. Research and development, installation equipment and manufacturing improvements in the helical piling industry have led to this trend. Moreover helical piles are typically smaller in size and weigh less than traditional piles, and require relatively smaller equipment and therefore it is a cost effective option. The latter is a very attractive feature for foundations installed in remote sites across Alaska. This paper presents full-scale pile load test results of helical piles and driven steel pipe piles installed in a site located in Anchorage, Alaska. Four full-scale pile load tests were carried out including two axial compression and two uplift load tests. Both helical piles and driven steel pipe piles were installed and tested at the same site under similar conditions to provide a direct comparison. The results of the full-scale load tests indicate the superior performance of helical piles compared to driven steel pipe piles. This paper describes the pile installation and test setup, presents the test data, and discusses the results.

Jan 1, 2009

By Gennaro G. Marino

During the preliminary design stages of the Illinois Division of Natural Resources(DNR) building, it was discovered that an old coal mine was present some 70 m (220 ft) beneath the building site. The new DNR building to be constructed is 36 m (120 ft)wide and 134 m (440 ft) long. It has three stories above grade and abasement level. The building is oriented north-south and has east and west ponds next to it (Fig. 1). The building is located on the State Fairgrounds in Springfield, IL. Given the history of surface subsidence of these underground coal mines in the Springfield area, there was concern about the potential for future subsidence at the building site. Mine subsidence events in the area have resulted in more than 0.9 m (3 ft) of settlement and have caused significant structural damage.

Jan 1, 2000

By I. Tsolas

This paper presents the use of non-parametric approach (i.e., data envelopment analysis, DEA) for the development of environmental sustainability indicators in mineral processing using environmental, economic and/or integrated indicators (i.e., indicators that interrelate two dimensions of sustainability). A case study based on real publicly available data is presented to illustrate how the proposed approach can be implemented in practice. The merit of this approach, which is based on the productive efficiency framework, is that it provides environmental sustainability indicators that can be used internally for benchmarking purposes and externally for sustainability reporting.

Jan 1, 2008

?General Facts:Barrick?sFirst Mine in Peru Production started in November 1998 ?The Facilities:Open Pit, Primary and Secondary Crusher Valley Fill Heap Leach PadMerrill Crowe PlantRefinery Environmental Facts: High Rainfall - Average Annual Precipitation of 1,200 mm (47 inches) Rainfall Events: Common 20mm daily events High Altitude Site - Elevations range from 3900 to 4250m. Steep topography - Terrain ranges from 3:1 slopes up to cliffs. Water Issues: Sediment Control - Open Pit PAG Encapsulation - Waste Dump Stormwater control - Leach Pad Erosion Control Techniques ? Offsite impacts mitigation Social Issues: 11 communities surrounding the property Town of Huaraz

May 1, 2003

By E. D. Attanasi

Geologic resource assessments describe the location, general characteristics, and estimated volumes of resources, whether in-situ or technically recoverable. Such compilations are only an initial step in economic resource evaluation. Forecasts that assume that resources that exist in nature can be commercially produced as needed ignore economic constraints. This paper identifies, by example, the salient features of a geologic assessment that will assure its usefulness for economic analysis. These features are demonstrated with examples of coal resource assessments and coal bed gas assessments.

Jan 1, 2001