Search Documents

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

This report presents the results of reconnaissance-level investigations of the mill refuse disposal systems for 15 plants throw-heat the conterminous United States. The sites visited represent a cress section f the copper, iron, lead and zinc, and phosphate industries&apos; practices in the field of fine-grained refuse disposal. The reconnaissance-level investigations were carried out to gather supplemental data to tae in-depth studies of Kennecott&apos;s Magma and Phelps Dodge&apos;s Morenci tailings deposits and Kennecott&apos;s Chino leaching dump. The various sites visited were classified according to the different systems and techniques used by the mining industry. The probable effects and relationships between site conditions and disposal methods were determined and evaluated to the extent feasible by a reconnaissance level investigation.

Jan 1, 1974

By Robert A. Bauer, Paul B. DuMontelle

In 1985, participants of the multi-year Illinois Mine Subsidence Research Program conducted surveys of subsidence effects on crop production from current high-extraction mining methods, selected a site to characterize the profile, strain, fracture development in overburden materials and changes in aquifers produced by subsidence from high-extraction mining, characterized floor materia1 s in three mines, and established bibliographic reference and data base files. The Illinois State Geological Survey, University of Illinois at Urbana-Champaign, Southern Illinois University at Carbondale, Illinois Department of Mines and Minerals and Twin Cities Research Center of the U. S. Bureau of Mines are coordinating State and Federally funded research.

Jan 1, 1986

By Chikaosa Tanimoto

INTRODUCTION Bratislava is located at the intersection of important traffic routes, including motor-ways, roads, railways, air traffic, trading, and inland waterway with an important harbour. The construction of the D2 Motorway Bratislava, Lamacska cesta Stare grunty was the last missing section of D2 Motorway and its completion linked the Czech Republic through Bratislava to the Hungarian Republic. Traffic was obliged until its completion to use the Lamacska Road and Mlynska Dolina, which were the most heavily trafficked roads in the city. The section of D2 Motorway to be completed in 2006 was 3,300m in length, of which the SITINA Tunnel was approximately half the length. After putting into operation the transit traffic(motorway) and urban traffic was separated. Transit traffic by passing the town was eased. The junctions D2 with Lamacska Road (Harmincova) and Mlynska Dolina also allowed better use of the motorway for the urban traffic The tunnel construction was specified by the features with the highly weathered and thermally altered granitic rock formation with the overburden of Quaternary sediment of 2?4 m thick, very thin overburden, severely controlled deformation limit and environmental protection. The tunnel had to be excavated beneath and nearby the academic complex area and the zoo, where sensitive facilities exist and animals live in. The tunnel consisted of two tunnels (Tunnel A and B) with the length of 1,415 and 1,440 m, respectively. The overburden thickness was in the range from 10?30 m. The standard cross-section and the one with invert arch were 79.5?81.5 m2 and 92.1?93.3 m2. The excavation took 21 months from September 2003 to May 2005. The construction was based on the concept of NATM. The SITINA Tunnel was the third application of NATM in Slovakia, following the BRANKISKO Tunnel (commenced in July 2003) as the first and the HORELICA Tunnel (in October 2004) as the second NATM practice. To protect the surrounding structures and citizens from tunneling operations, seismic monitoring was performed in association with blasting. The allowable limit of blasting vibration was fixed to be under the particle velocity of 15 mm/sec. The tunnel excavation cleared this limit as expected before construction. In driving through the difficult geological situation the excavation work hit 49 faults, and some of them occasionally caused serious face instability. In principle, the rock formation has been affected by the high hydrothermal effect and the resultant clay filing along faults and joints. The auxiliary reinforcement with the 4?8 m long pipe roofing was needed to protect the vicinity of mining face area. This operation extraordinarily required additional works and time which had not been expected before construction.

By Martin Herrenknecht, Karin Bäppler

The last five years have seen a remarkable increase in tunnelling projects in both soft ground and hard rock applications. Part of the increase is a result of recent Research & Development efforts to improve Tunnel Boring Machine (TBM) adaptability, capability and reliability. This paper will review the latest innovations in the TBM industry and explain in detail the results of these innovations followed by a forecast where the technology will take the tunnelling industry in the future.

Jan 1, 2005

By William Gleason

"Government support for Canada’s mineral industry was on full display during the Prospectors & Developers Association of Canada (PDAC) conference in Toronto, ON, Canada on March 3-6. First, there was the announcement of the five-year extension of Canada’s Mineral Exploration Tax Credit (METC), the first multi-year extension of the METC since its inception in 2000. Canada’s Minister of Natural Resources, Amarjeet Sohi, added to that support when he spoke at the opening keynote session and announced the Canadian Minerals and Metals Plan (CMMP), a plan that aims to map out the future of the industry in Canada. Finally, the support for the mining industry was buttoned up with a visit to the conference by Canadian Prime Minister Justin Trudeau.More than 25,000 people from 135 countries attended the annual conference that features a robust trade floor, technical sessions and an investors’ exchange that aims to put mining companies in touch with potential investors. Mining companies and ambassadors from nations around the world are given the opportunity to present to small audiences throughout the conference and this year PDAC was able to sway the Prime Minister to speak on its behalf.Trudeau sat down with PDAC President Glenn Mullan on March 5 to talk about the METC extension and a host of other issues important to the Canadian and global mining industry, giving the home country a bit of a profile advantage when it came to making a pitch to investors.Trudeau entered the week of the conference in the midst of the most serious political scandal of his career and was defending himself against accusations of political interference with the top prosecutor in the land over a criminal case involving one of Canada’s largest companies, SNC-Lavalin. During the question-and-answer session at the Metro Toronto Convention Center, Trudeau seemed more than happy to keep to the discussion about mining. He spoke favorably about the industry during the half hour conversation and praised the industry for its work with Indigenous people as well as its efforts to advance technology and innovation. He made a case that Canada is a safe and reliable place for investment in the minerals sector.“We are at a time of change right now, of transformation with new technologies and global supply chains, and everyone is trying to adjust to the new realities that have accelerated so much these past years,” Trudeau said. “What we are trying to do as a country and what you have done as an industry is to try to look at where things are going – go to where the puck is going to be, not where it is. You, as an industry, know that investments in innovation, research, science — investment in technology and partnerships with Indigenous communities are all things that are going to give you opportunities to be competitive in the coming years.”"

Apr 1, 2019

By Fred N. Kissell, Jerry C. J. Tien, Edward D. Thimons

At coal mine working faces, simultaneous application of three basic elements reduces the methane explosion hazard: (1) adequate ventilation, (2) regular monitoring of gas concentrations, and (3) the elimination of ignition sources. This paper reviews the application of these elements in a manner relevant to Chinese coal mines. Adequate ventilation is provided by using the mine entries to convey air for the long distances between the mine portal and the working sections (main ventilation systems) and then using line brattice or ventilation duct (face ventilation systems) to convey air the last hundred meters to the working face where coal is broken and removed. The air quantity provided is enough to safely dilute methane and the air velocity is enough to prevent layering. Gas concentrations are regularly monitored in accordance with regulations using knowledge of the circumstances under which the highest concentrations are likely to be found. Ignition sources are eliminated by ensuring that electrical equipment does not ignite methane, that sparking from cutter picks is minimized, and that smoking by workers is strictly forbidden. Risk-reduction studies using fault-tree analysis have shown that large reductions in explosion risk only result from multiple preventive actions. For example, a ventilation upgrade or a methane monitor upgrade by itself offers risk reductions under 50 pct. A risk reduction of 90 pct. or more would typically require much more. Other studies have shown that the everyday vigilance of those working underground is as important as engineering design.

By T. T. Tomimatsu

[This Bureau of Mines paper investigates explores, and analyses the Corporate structure dynamics and Rancid role to evaluate the economic health of the U.S. copper producers. It highlights the Corporate policy options and measures of corporate profitability and suggests that a competitive domestic copper industry will exist in the future. The study highlights the activities of 14 selected major copper-producing companies, including their subsidiaries o affiliates, that were responsible for more than 95 percent of the total U.S. production in each of the years since 1969. The selected firms are hot all primarily in the business of producing copper. Several of the large producers are classified by the financial institutions as integrated oil and gas enterprises.]

Jan 1, 1980

By C. B. Manula

This report is volume 7 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design. Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation," and ventilation. This volume of the final report describes the Rail Haulage subsystem of the Master Design Simulator. This subsystem can be used as a free standing model or can be linked to the Production subsystem to provide rail haulage capability. Complex rail haulage systems can be realistically simulated with this model. This report includes complete instructions for operating the subsystem as well as a program listing. In addition, a case study is included which illustrates the application of the subsystem when linked to the production subsystem.

Jan 1, 1974

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By H. Nelisse, S. K. Patra, A. Natani, S. Rakheja

The current laboratory methods for assessing the vibration attenuation performance of seats involve repetitive trials with a number of human occupants, and raise certain ethical concerns. Moreover, the measurements with human subjects yield considerable variability in the data. Alternatively, several anthropodynamic manikins have been developed for effective assessments of the coupled seat occupant system [1]. The effectiveness of a manikin in predicting the response of a coupled seat-occupant system lies in its ability to reproduce the biodynamic response of the seated human body in terms of force-motion relationship at the body-seat interface, such as apparent mass (APMS). A number of prototype manikins have thus been developed on the basis of biodynamic characteristics of vertical vibration-exposed seated occupants of different body masses in the vicinity of 5th, 50th and 95th percentile male population. This study concerns with the analysis of a passive prototype manikin to enhance its ability to reproduce the idealized APMS response characteristics of the vibration-exposed seated human subjects defined in ISO-5982[2] for mean body masses of 55, 75 and 98 kg. Methods The APMS responses of a prototype anthropodynamic passive manikin were thoroughly characterized in the laboratory under different excitations and body mass configurations. The manikin was designed with sufficient flexibility to configure mechanical-equivalent models corresponding to seated body masses of 55, 75 and 98 kg, by adding/removing specified masses and springs (Fig. 1). The manikin, configured for a specific body mass, was positioned on a rigid seat without a backrest, which was fixed to the force platform of a whole-body vertical vibration simulator. The simulator was programmed to synthesize random vertical vibration with flat acceleration power spectrum in the 0.4-20 Hz frequency range with two different magnitudes: 1 and 2 m/s2 overall rms acceleration. The total static and dynamic forces of the manikin to and the seat were measured using the force platform, while a single axis accelerometer was installed on the seat pan to measure acceleration due to vertical excitation. The measured data was appropriately corrected for the rigid seat inertia force, and the apparent mass [ ]

Jan 6, 2006

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By Pradip, Beena Rai

A molecular modeling study was carried out on an adsorbed oleate monolayer on the surfaces of three calcium minerals, fluorite, calcite and fluorapatite using Universal Force Field (UFF) potentials. The cleavage plane of calcite {104} was the best template for oleate monolayer adsorbed since the surface structure enabled all the calcium sites available on the surface to be occupied by oleate anions. The area occupied per chain of oleate in this well packed monolayer was computed to be 20.2 Å, which exactly matches the value calculated to be the parking area per oleate molecule for a fully packed monolayer based on strictly geometric calculations. On the other hand, the precentage of calcium sites occupied by oleate to achieve a fully packed monolayer in case of fluroite and and fluorapatite was found to be 67% and 75% respectively. The results of this theoretical study suggest that while all the three adsorption conformations, that is unidentate, bidentate and bridging type are equally likely on fluorite and fluorapatite, bridging is most likely on calcite. Interestingly, all the conformations are observed experimentally for calcite-oleate system also. The reasons for this discrepancy between the theoretical predictions and experimental observations are not clear. More work is required to resolve this discrepancy, in particular simulation studies in presence of solvent water molecules on the surface.

Jan 1, 2003

By N. F. Mescheriakov

New mechanical and pneumatic-mechanical flotation machines with axial impellers have been developed. Industrial tests show that these machines ensure lower power expenditure (on flotation) by 1.5-2.0 times as compared with reference machines (with the same or improved technological indices). Application of the newly developed axial impeller, with these advantages, is possible in any volume chambers of type OK, Dorr-Oliver, Wemko etc.

Jan 1, 1998

By Andre Zingano

The variation in pillar behavior at underground coal mines working in the Bonito coal seam is observed in both research and mining company case studies. There is no consistency in pillar behavior, as it varies from mine to mine. In some cases, it is possible to find rib yields for both excavation modes and pillar sizes. This paper?s objective is to investigate pillar behavior for different load conditions and pillar sizes. Three-dimensional numerical simulation models considering these factors were built. A matrix was then assembled to compare pillar behavior between loading conditions, as well as between different pillar sizes with the same loading condition. The results showed some pillar rib plasticity due to vertical loading and stress relief independent of the pillar size and load. For the same load conditions, the yielding thickness is the same for different pillar sizes.

Jan 1, 2012

By F. D. Ford, Z. Dai

"Vale’s Ontario Operations re-introduced Cu/Ni separation at Clarabelle Mill in 2006. The mill processes ores from a number of mines in the Sudbury basin. A saleable Cu concentrate is produced at 30-60% Cu recovery from mill feed, which has to meet the quality specification. In particular, Ni content in Cu concentrate must be less than 0.6%, otherwise, penalties will apply and diminish the value of Cu concentrate, in addition to the lost Ni value. Generally, a Ni grade of less than 0.4% is obtained in Cu concentrate. More recently, while processing Cu-rich ore, Cu concentrate contained more than 0.6% Ni which is abnormally high. Detailed mineralogical investigation shows that Cu-rich ore contains more millerite in comparison to typical Sudbury Ni sulphide ore. Millerite is found to be more floatable than pentlandite and is much more difficult to depress using high-lime aeration conditioning, which is the standard practice in Cu/Ni separation to float chalcopyrite while depressing pentlandite. The current operation uses sodium cyanide at 20 g/t to depress pentlandite and pyrrhotite. However, it is found that a high dosage is required to depress millerite. It is also shown that starch and dextrin are promising in millerite depression.INTRODUCTIONPrior to bulk smelting in 1991, Cu/Ni separation was carried out at Vale’s Copper Cliff Mill, Ontario Operation. The typical Cu concentrate grade was around 30% Cu and 1% Ni. This is very high in comparison to today’s value of 0.4% Ni and would not be acceptable for external processing. However, the Cu concentrate was processed internally at the Copper Cliff smelter/refinery, so the Ni contained in Cu concentrate was not lost and no actual penalties applied. During the SO2 abatement initiative, bulk smelting was chosen because of the perceived simplicity and consequently, Cu/Ni separation was eliminated (Agar, 1991) and the Copper Cliff mill was subsequently demolished. In 2005 and after more than one decade of bulk smelting, business changes required the removal of some Cu concentrate from Clarabelle Mill bulk concentrate to provide smelter capacity for Voisey’s Bay concentrate in the Copper Cliff smelter. In essence, this strategy calls for Cu removal at Clarabelle Mill (Lawson, 2006). In this case, Cu concentrate is sold externally and it must meet the quality requirement of less than 0.6% Ni."

Jan 1, 2011

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

By Harvey W. Parker

The underground industry is challenged by many complex technical and non-technical issues and risks. The most obvious of these are the traditional technical issues that we usually try to address with risk management techniques. However, there are many other non-technical risks that our projects face on a daily basis which we often fail to fully recognize or appreciate. This paper addresses some of the less-technical broad-based risks in order to put them into perspective with the technical risks we face day to day in underground planning, design and construction. The good news is that Risk Management techniques are not always about bad things. For obvious reasons Risk Management is always thought of in terms of the ?downside? of risk (i.e., the identification and mitigation of things that can go wrong). On the contrary, there is an ?upside? of things that might go better than expected. Fortunately, if a deliberate effort is made, the same principles and techniques that our industry uses in Risk Management can be applied toward identifying and quantifying the Opportunities and Benefits that might occur. In this way, the process of conducting risk management programs can not only identify the downside risk but can be used to identify and direct projects to take advantage of the upside of uncertainty (i.e., Opportunities as they arise). This beneficial aspect of risk management programs will be highlighted in this paper together with the importance of the non-technical issues.

Jan 1, 2008

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968