Search Documents

By Vincent A. Scovazzo

Benchmarking is a business management process that seeks improvement through the study and reapplication of practices conducted by industry leaders. This discussion presents objectives and organization of benchmarking applied to mining geomechanics. Similar procedures have been successfully applied to mining companies, laboratories, and research organizations involved in mining geomechanics throughout the world. Benchmarking is a structured process that allows an organization to learn from the "best" in the field. The objectives of benchmarking vary depending on the company's targeted areas for improvements. Typical goals include ground control cost reduction, enhanced safety, optimization of geotechnical staffing, development of state-of-the-art design procedures, or the adoption of the "best in the field" geotechnical data management. Once the objective of the study is established and the practices and procedures to be benchmarked are identified, a benchmarking team is formed from internal and outside specialists. Benchmarking in geomechanics is fundamentally different than in most other fields because of the effects of local geologic conditions and regulations, both of which must be understood by all on the benchmarking team, before a comparative analysis can be made.

Jan 1, 2000

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By Chris G. Leach

"Abstract A seven storey Northbridge area of Perth, Western Australia presented residential apartment complex located in the an opportunity for a novel application of Cutter Soil Mix technology (CSM). The development included a two-level basement for car parking which covered the full site area. However, the basement was also required to extend under an existing single story heritage building. Soil conditions comprised 2m of fill overlying medium dense to dense sands that in turn were overlying a very stiff clay stratum at approximately 14-16m depth. The ground water table was located at a depth of approximately 1m below the natural surface level.A site boundary consisting of a reinforced CSM retention system and was designed and installed to allow the excavation to proceed to basement level. Two rows of temporary soils anchors or inclined struts were required to achieve this. A CSM support system for the heritage building was also designed and constructed to provide temporary support during excavation and permanent construction works. The brief for the contract works emphasised that it was vital that settlements of the heritage building be kept within strict limits.CSM is a relatively new introduction to the Australian construction market, using a modified trench cutter to mix a binder slurry with in situ soils, generally to form cut-off walls, retaining walls and soil improvement works. This project is understood to be first application of the CSM for underpinning work in Australia.This paper discusses the site background details leading to the decision by the client to adopt CSM technology, and the design and construction aspects to meet the challenges offered by this project.Introduction190 Newcastle St is a 7-level residential apartment complex located in the Northbridge area of Perth, Western Australia. The development includes a 2 level basement for car parking, which covers the full site area. The basement also extends under a single story heritage building, which remained in-situ throughout the building works.A site boundary retention system was required to allow the excavation to basement level to proceed. In addition, a support system for the heritage building was required to provide temporary support during excavation and permanent construction works."

Jan 1, 2014

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005

By Ilpo O. Auranen

Background: Mines of today are moving ever increasing tonnages of rock. The new ore bodies tend be of lower grade and located deeper in the earth?s crust. The industry?s focus to overcome this ?deeper but poorer? ore problem has traditionally been to lower the costs by increasing the scale of mining. This has resulted in an ever increasing size of mining equipment like drills, loading shovels, dump trucks. The main focus has been in reducing the cost per ton of mining. This cost focus has often resulted in increased waste rock dilution and more ore losses. From costs to value: Waste rock dilution means waste rock in the concentrator feed. It?s value in open pit mining is equal to the value of ore it replaces. In underground mining, waste rock dilution?s value is equal to the value of ore it replaces added to the costs of mining it. It is commonly accepted that waste rock dilution in open pit mining ranges between 5 and 20% and in underground mining between 5 and 40 % . In a typical large open pit mine ore value is from 20 to 60 USD per ton and mining costs are 1 to 3 USD per ton. One percentage point reduction in waste rock dilution represents savings corresponding to about 20% of total mining operation costs. The difficulty of reducing waste rock dilution comes from the complicated nature of the ores. Accurate ore waste-border detection has not been possible due to excessive costs. Core drilling combined with geochemical lab analysis is the most accurate method for locating ore waste borders. However, it is also expensive and time consuming, which is why it is often combined with somewhat lower cost methods like sampling drill cuttings from blasting drill holes or from reverse circulation drills and analyzing them in a laboratory. The main drawback with these methods, in addition high costs, lies in the sampling accuracy and in the quality control of the whole process when a large number of samples have to be handled manually. In every mine it is possible to halve waste rock dilution by using new on-line analysis technology .

Oct 1, 2009

By H. Askari-Nasab, S. Upadhyay, A. Moradi-Afrapoli

Material handling in surface mines accounts for around 50% of the operational cost. Optimum truck dispatching plays a critical role in the reduction of this operational cost in truck and shovel surface mines. Researchers in this field have presented several mathematical models to solve the truck dispatching problem optimally. However, a critical survey of the literature has shown that three significant drawbacks exist in the available truck dispatching models. The published models underestimate the importance of the interaction between truck fleet, shovel fleet, and the processing plants. They also disregard goals set by strategic-level plans. Moreover, none of the available models account for the uncertainty associated with the input parameters. In this paper we present a new truck dispatching model that covers all of these drawbacks, using a fuzzy linear programming method. The performance of the developed model was evaluated through implementatin in an active surface mining operation. The results show a significant improvement in production and fleet utilization.

Sep 1, 2021

By Daniel Bennett

There are few methods currently applied towards on-line bulk mineralogical analysis. Yet on-line knowledge of process mineralogy could potentially provide large benefits, such as increased extraction efficiency or resource optimization. The work described in this paper involves the development of radio frequency methods for bulk mineralogical analysis. Some resonances that occur in the radio frequency spectrum are mineral specific, and potentially allow quantitative estimation of mineralogy in an ore stream. Results will be presented on the specific detection of chalcopyrite. Initial quantitative measurements investigating matrix effects have indicated the feasibility of on-line mineralogical estimation using radio frequency techniques.

Jan 1, 2006

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011

By Steve Kral

The coal mining industry in the western United States is seeing the same boom as the rest of the country and the world. Most coal mines in the West are operating flat out as the nation’s appetite for energy continues to grow. And many of the coal mines have either increased their production capacities or are in the process of doing so. However, transportation issues along with environmental restrictions are keeping many mines from expanding even further. Some coal companies held off on further expansion plans until Congress and President Bush could agree on a national energy policy, one that recognizes coal as the nation’s leading source of electricity. In August, Congress passed and the president signed into law such a measure (see Washington Survey, page 7). The legislation includes research funding for clean coal technologies. So western and eastern coal could become even more important in the national energy picture. This is particularly true as supplies of natural gas diminish and the price of oil continues to increase.

Jan 1, 2005

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971

After the closure of collieries, they naturally start to fill up with water. As a result, hydraulic gradients develop between them and different hydraulic pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The collieries in the Witbank Coalfield have geometries such that there are several areas where this intermine flow is possible. Since the Department of Water Affairs and Forestry has declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon is required. The challenges in determining intermine flow are numerous, and attention has focused on identification of areas where these flows can take place. The quantification of these flows is problematic due to the uncertainties in exact geometric configurations and the variation in site-specific hydraulic properties of thecoal and overlying lithilogical layers. During this study, use has been made of numerical flow modelling and several analytic solutions to test the applicability of the flow models as well as to predict groundwater flow directions, filling times of voids and flow volumes. The numerical modelling methodology entailed a downscaling approach starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines, and finally looking in detail at the major areas of interaction.

Jan 1, 2005

By Michael R. Norland

This U.S. Bureau of Mines report on U.S. and Canadian 1iterature pertaining to soil characterization and the use of soil amendments as a part of the reclamation process of coal surface-mined lands contains 1,280 references. The references were published during the 1977 to 1988 period. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate those articles with the coal mining region and subjects of interest. All references are annotated.

Jan 1, 1991

By A. Fahimifar, H. Soroush

Abstract: In order to develop non-destructive methods in studying physical and mechanical properties of rock and replacing them with difficult and expensive static methods, several ultrasonic tests were carried out on cylindrical rock specimens in accordance with the ISRM suggested methods and velocity of P and S waves were determined. Also, density, porosity, water absorption, uniaxial compressive strength and indirect tensile strength were determined for each specimen in accordance with ISRM suggested methods. According to above tests static and dynamic elastic constants were calculated After statistical analysis of data obtained from tests, the relationships between velocity of elastic waves and physical or mechanical parameters were determined and some equations were obtained. Also similar analyses were performed on static and dynamic constants and some equations were extracted. Using these equations, the physical and mechanical parameters of rock and also static elastic constants can be estimated by conducting simple and quick tests (i.e. ultrasonic tests). Abriß: Um zu entwickeln, die zerstörungsfreien Methoden für Studieren die physischen und mechanischen Eigentümer von Steinen und auch ist für Ersetzen diese Methoden mit schwierigen teuren statischen Methoden, mehrere altrasonic Prüfungen auf zylindrischen Steinproben gemäß ISRM anregenden Methoden und den Geschwindigkeiten von S und P Wellen bestimmt worden sind durchgeführt worden. Außer der Dichtheit und der Porosität betonen Wasser Aufnahme und monoaxial Widerstand und dehnbaren indirekten Widerstand jeder Probe betreffend der erhaltenen Ergebnisse die atmosphärische Aufladung sind bestimmt worden und die dynamischen Faktoren der Steine sind kalkuliert worden. Nachdem statistische Analyse die Korrelation der Ergebnisse zwischen der Geschwindigkeit elastischer Wellen und mechanischer und physischer Eigentümer der Steine erhalten worden ist, und mehrere Verhältnisse sind vorgeschlagen worden. Eine ähnliche Analyse ist auf atmosphärischer Aufladung und dynamischen Faktoren durchgeführt worden und einige Verhältnisse sind erhalten worden. Mit Hilfe dieser Verhältnisse die physischen und mathematischen Eigentümer von Steinen und auch können die Statistik Faktoren durch einfachen und schnellen altrasonic Prüfungen erhalten werden. Resume: Puor le development des method non-destructive et evaluuation des propietes physical et mechanical des rock et superseding avec les methods dificzle et cher statique, c‘ est fait plusieur essayes ultrasonique sur les echantillons cylinrique et par a port le proposale TSRM et le vittesse des ondes P et S et densite et porosite et absorption des eaux le resistant de pression uniaxial et resistance de chaque echantillon est determinee. A la fin en base des resultat obtenue les constant statique et dynamique des roches sont calcule. Apres les analyses statistiquc sur les resultat obtenue du les essaybs, c‘ etait produit les relation entre les viptesse les ondes elastique et les proprietes physic et mechanicue des roches et c est propose quelque relations. Aussi le meme enterpretation sur les constant statique etdinamique. En possezon de ces relations, les spesificatio physique, aussi on peut trouver leur constant statique, avel les essayes sample et raptid a d ultrasonique.

Jan 1, 2003

By Henry C. Meeves

The Bureau of Mines investigated the silver production potential of the Leadville (California) mining district, Lake County, Colo., in 1966-67. The mining history of the district, the ground conditions encountered in mining, and the mine-support methods used are reviewed. The drainage problem is discussed in detail. An initial objective was to establish the existence of potential silver resources minable by low-cost open-pit methods, particularly in the silver-bearing manganese halos surrounding the major deposits. The report concludes that under present conditions, development of the deposits in the area is not economically feasible; however, a pioneer rotary noncore drilling program demonstrated that this type of exploration is technically feasible. Potential reserves of silver and associated metals are estimated. Possible mining methods for recovery of the reserves are discussed. Future production possibilities from the various subareas of the district are analysed, considering optimum operating size. Consolidation of small individual holdings for unit operation is recommended. Type of operation, amount of rehabilitation, size and type of concentrating plants required, drainage and other mining problems, and metal price trends are discussed as they bear on economic feasibility of development.

Jan 1, 1970

By D Morgan, K Jones

"In March 2015 Northparkes Mines (NPM) installed a process mineralogy facility on-site. The laboratory included a TESCAN TIMA scanning electron microscope (SEM) and was the first SEM facility to be commissioned on a mine site in Australia. While the initial intent of the quantitative mineralogy laboratory was to provide information to drive processing plant improvements, in practice, it has been utilised for so much more and is now serving as an integral link between departments on-site. This multidisciplinary approach to orebody knowledge is a new strategy for NPM whereby all parts of the value chain are aligned towards the common goal of achieving process efficiency and stability while still maintaining high throughputs. The NPM experience is presented as a case study to illustrate how on-site process mineralogy can drive a realignment in business strategy with a common goal of mill optimisation, stability and more realistic forecasting through orebody knowledge and information sharing between disciplines.Citation:Jones, K and Morgan, D, 2016. On-site Process Mineralogy - Linking Departments and Disciplines with the Common Goal of Increasing Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 149–156 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Robinson KJ

There has been much debate in recent years regarding the number of Geology (Earth Science) graduates produced in Australia. The key variable has commonly been assumed to be the placement of graduates in the mineral and petroleum industries. Although not wishing to deny the importance of this element, we contend that Geoscience studies should be given to a wider variety of graduates. The essence is to make students and future citizens more environmentally aware. INTRODUCTION Geoscience is fundamental to exploration and to the well-being of the minerals industry and hence the Australian economy. The value of mineral primary products exports for the past three years has been: 1895 $15.3 billion 1986 $14.8 billion 1987 $16.3 billion (Data source: B.M.R) The mining industry supplies about 40% of Australia's export earnings. However the overall value of Geoscience to the Australian economy is much greater. At the opening of the ANZAAS conference in Townsville during May 1987, Sir Bruce Watson , Chairman of the Mt. Isa Mines Ltd., made a plea for a national re-examination of the way science is taught in secondary schools. In particular he emphasized the point that the community should be more aware of the importance of Geoscience and the value of the mining industry to Australia.

Jan 1, 1989

By D. Kolymbas

A simple formula is introduced which allows the evaluation of dynamic pile tests. The following case is considered: The pile top is dynamically loaded by an impact. The velocity v of the pile top is recorded over the time. Let v1 and v2 be the first and the second maximum of this curve. Then, the pile bearing capacity (resulting from ideally plastic resistance at the pile wall and at the tip) can be set approximately equal to Z(v1- ½ v2), where Z is the impedance of the pile cross section. Due to the assumption of ideal plastic resistances, radiation damping needs not be taken into account. Material damping may be important in rate sensitive soils (such as clay, even if it is highly overconsolidated). A simple correction procedure for material damping is proposed.

Jan 1, 1989