Search Documents

Experimental results are presented that test the hypothesis that the descaling behaviour of stainless steel slabs following reheating is controlled by interfacial roughening at the scale-steel interface. In this investigation, two stainless steels were considered: type 304 (austenitic, with 18% Cr and 8% Ni) and type 412 (ferritic/martensitic, with 11.6% Cr). It was found that the entanglement that arises at the scale-steel interface was in fact effective in maintaining scale-steel adhesion, under the mechanical descaling conditions used. In the case of type 304, descaling proceeded by fracture along chromite layers, which formed (by internal oxidation) on the austenite grain boundaries; for this steel, the extent of descaling depends most strongly on austenite grain structure, and not primarily on the conditions in the reheating furnace. In contrast, type 412 samples descaled only at the edge of the entangled zone, and showed a greater sensitivity to the reheating conditions; specifically, higher free oxygen in the reheating gas and longer reheating times were found to increase the residual scale thickness. Key words: stainless steel, reheating, scale, entanglement, descaling, fayalite, internal oxidation, grain structure, free oxygen.

Jan 1, 2003

By W. E. Falck, A. Usubiaga, J. Spangenberg, P. Schepelmann, S. Šolar, D. Wittmer, F. Blanchard

The extraction and processing of mineral resources may be accompanied by environmental impacts. In spite of technological advancements, the enormous increase in production volumes within the last decades has induced sizeable environmental impacts along the life-cycle of products. Beside environmental impacts, social issues associated with mining need to be considered to ensure the social acceptability of mining activities. The project EO-MINERS aims at deploying Earth Observation (EO) tools to inform best practices in mining and to thus assist the global mineral resources industries in their transition to sustainable development. In order to facilitate the handling of complex sets of information requirements from a wide variety of stakeholders, a set of indicators was developed that will inform the process of EO tool and services development. The project strives to enable stakeholders outside the industry to meaningfully participate in decision-finding processes on mining-related issues by developing and providing EO products and services that fit the information requirements. The project has identified a wide range of such information requirements by stakeholders that could be potentially provided by EO tools. The applicability of the EO tools on the local level is tested on three mining sites.

Jan 1, 2011

By Seth L. Pearlman

A major excavation support case history for the Eastern approach to the Third Harbor Tunnel (THT) in Boston, MA is described, which uses an anchored Soil Mixed Wall (SMW). Both general and project specific information is provided regarding the design and construction of SMW walls. In addition, conclusions are presented that discuss the suitability of this particular application and other possible variations.

Jan 1, 1993

By Bengt H. Fellenius

THIS PAPER deals with the analysis of results from axial testing of vertical single piles, i.e. the most common field test per-formed. Despite the numerous tests which have been carried out and the many Papers which have reported on such tests and the analysis thereof, the understanding of pile test loading in current engineering practice leaves much to be de-sired. The reason for this is that the engineers have concerned themselves with mainly only one question: "Does the pile have a certain least capacity?", finding little of practical value in analysing the actual capacity and the pile-soil interaction. This Paper aims to show that engineering value can be gained from elaborating on a pile test ? during the actual testing in the Held, as well as in the analysis of the results. The first portion of the notes make use of an earlier Paper by the author (Fellenius. 1975). However, additional views and recent literature have been incorporated.

Jan 1, 1988

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

By J. D. Miller

Characterization of feed material with respect to expected concentrate grade and recovery is fundamental to the design of improved separation efficiencies and to achieve sustainable development in the utilization of our mineral resources. An important reference point for this characterization is the liberation-limited grade/recovery curve which represents the perfect separation, the best separation which can be achieved for a given feed material limited only by the extent of liberation. Now, liberation-limited grade/recovery curves can be determined based on 3D mineral liberation analysis of feed material. Thus, actual separation efficiencies can be compared to what might be expected for a perfect separation limited only by the extent of liberation. It is shown that 3D mineral liberation analysis based on X-ray micro CT (XMCT) is preferred to 2D section analysis which overestimates the extent of liberation. By way of example, procedures and experimental results are presented and discussed for feed material in the case of phosphate rock flotation.

Jan 1, 2009

By James W. Reil

A test series of small, precisely-controlled and thoroughly-monitored production blasts was conducted at two quarries. In each series, all variables except delay were kept constant, as much as practically possible. The first aim of the study was to determine the effect of local geology on ground vibration. The second aim was to test several hypotheses relating the effect of millisecond delay intervals to fragmentation and ground vibration. A resonant frequency of ground vibration was shown to be related to the thickness of the overburden, in accord with a model proposed by Gupta (1961). Since the overburden geology creating this resonant vibration cannot usually be changed, two methods were tested to choose delays such that blast vibrations would destructively interfere. These were shown to be effective in modifying both the peak particle velocity and response spectra of ground vibration. The delay interval chosen also affects fragmentation, primarily in massive rock, with an optimum relief between holes of 2 ms/ft. Strain gage records indicate a possible mechanism consistent with this information.

Jan 1, 1985

By J. Goyman, K. R. Rawling

"1.1 Location and Transportation ServicesNanisivik Mines Ltd. is located at latitude 73°, 3,200 km north of Montreal and 700 km north of the Arctic circle, on the south side of Strathcona Sound, which is an arm of Admiralty Inlet, in Northern Baffin Island. The orebody and mill site are 4 km distant from Strathcona Sound which provides deep water anchorage for ocean transportation of concentrate to Europe during the short northern shipping season from mid-July to mid-October.The operations and the resident community have direct jet aircraft service from Montreal two days per week, and local nights connect with other Arctic communities in the northern Baffin region. Bulk supplies and general cargo are delivered in the summer shipping season.1.2 HistoryThe Texas Gulf Sulphur Company, now Kidd Creek Mines Limited, staked claims in the Nanisivik area in 1957 and carried out exploration through to 1968. After the Kidd Creek orebody was found, Texas Gulf optioned the property in 1972 to Mineral Resources International Inc. (MRI), which undertook further exploration and completed a feasibility study.Nanisivik Mines Ltd. was formed in 1975, with MRI as the majority shareholder and minority shareholdings held by Metallgesellschaft, Billiton and Texas Gulf. Strathcona Mineral Services Limited was retained to manage the project during both the construction and operational phases."

Jan 1, 1984

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By R. Benito

The publication of the Lerchs Grossmann paper in 1965 outlining a threedimensional graph algorithm for ultimate pit definition set the standard for the mining industry regarding pit optimization. Although the algorithm provides a solution from a static standpoint (i.e., assumes instantaneous mining), it is widely used for commercial packages to generate ultimate pit limits and intermediate phases. However, the solutions delivered are presented in canned reports lacking connection to the original data, which prevents further data analysis and extended reporting. The approach presented in this paper attempts to overcome such barriers by performing openpit optimization through databases. An adaptation of the Lerchs Grossmann graph algorithm is used to generate nodes, arcs and tree structures in customized tables to determine the maximum closure of a graph.

Nov 1, 2013

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the “bigger-the-better” design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

By Mike Higgins

"Data management is emerging as a major concern for miners. Engineers today are faced with anextensive array of data from varying sources, and are required to consolidate and analyse thisinformation to produce an effective and efficient mine plan. The viability of a mining operation canbe dependent on the outcomes of this process. With so much at stake, it is no surprise that mostengineers prefer a standard approach to blasting which is designed to minimise risk rather thanoptimise performance."

Jan 1, 1998

By R. J. Anderson, A. V. Castelli

In 1986, United States' barite production fell 48.9%, consumption - sold or used by grinding plants - was off 47.3%, and imports were down 63.8%. Meanwhile, world mine production decreased 29.6%, according to the US Bureau of Mines. However, value of US-produced barite FOB mine increased 46.51%, according to USBM figures. The declared value CIF US port of all imported unground barite decreased from $41.94/t ($46.23 per st) to $39.02/t ($43.01 per st). Nevada continued to be the leading US producer of barite with 69% of the total. It is followed by Georgia, Missouri, Tennessee, and California. The USBM estimates that 65% of the barite mined was used as a weighting agent in drilling fluids. The remaining 35% was used in the production of barium chemicals and as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector made up a larger percentage of the US produced barite in 1987 than it did in 1986, increasing the overall value per ton of barite. Barite consumption was at its lowest since 1963. It is estimated that 80% of the barite was consumed in the drilling fluid market. The remaining 20% was used in barium chemicals, glass, and as filler in plastics and paper. The decline of barite used in drilling fluid followed the decline in the average number rotary rigs operating - 964 versus 1968 in 1985. This was the lowest average number of rotary rigs operating since 1971. The non-oilfield market was up 5.3% in 1986. This increase can be attributed to the increased use as a filler in plastics. Imports of crude barite, though down nearly two-thirds, still made up 65% of the barite consumed in the US. China was the leading exporter to the US with 58%, followed by India, 15.4%; Morocco, 11%; Thailand, 5.4%; Mexico, 4.6%; Chile, 3.9%; and Ireland, 1.7%. Less than 1% of the imported ore was used in the nonoilfield sector. Imports of ground barite dropped from 64.4 kt (71,000 st) to 19.8 kt (21,800 st) in 1986. Of this amount, 14.1 kt (15,500 st) were used in drilling fluids in 1986 and the remainder for non-oilfield use. During 1986, more of the grinding plants supplying the drilling fluid market were closed. Dresser Magcobar and IMCO Services, a Halliburton company, formed M-I Drilling Fluids Co. Mine production in the US will probably decrease in 1987 due to the lower cost of imported ore. No significant change is expected in the drilling fluid market. The average number of operating rotary rigs is estimated at 950 in 1987 versus 965 in 1986. The nondrilling fluid markets (chemicals, glass, and filler) will follow the overall US economy. Bauxite and alumina R. J. Anderson, Ohio State University US bauxite production in 1986 dropped to a pre-World War II level, continuing a decline that began a decade ago. 1986 production totaled 450 kt (496,000 st), compared to 674 kt (743,000 st) in 1985. World production of bauxite also decreased in 1986. This reflected the soft market in alumina, aluminum, and related products. Total mine production worldwide came to 79 Mt (87 million st), down from 85 Mt (94 million st) in 1985. For the sixteenth consecutive year, Australian production of bauxite led all other sources. No other country approached the 28 Mt (31 million st) mined in Australia in 1986, despite a 4.4-Mt (4.9-million st) drop in its output from 1985. Other major producers in 1986 were: Guinea 11 Mt (12 million st), Brazil, 6.5 Mt (7 million st), Jamaica, 6.5 Mt (7 million st), and Suriname 2.8 Mt (3 million st). Despite weakness in world demand for bauxite, Venezuela, heretofore an alumina producer, is now pushing development of a new mining venture near the western border of the state of Bolivar. Plans call for barging bauxite down the Orinoco River to the Ciudad Guyana alumina plant, a distance of 650 km (400 miles).

Jan 5, 1987

By J Young, S Yu, P Moyo, M Powell, A Musunuri, B Bonfils, S Kanchibotla, P Yaroshak, V Jokovic

The appropriate design of liners continues to be an issue on many mills worldwide. Loss of milling capacity especially at liner change, uneven wear lives along the mill, substantial scrap on worn liners, excess mill down-time, undesirably short and unreliable wear lives are all common issues. This paper presents a designed approach to liner optimisation that follows a logical path of initial design and step-wise improvements based on liner wear monitoring. The target is to have a good liner design from start-up, then tune the profiles, heights and thicknesses based on wear monitoring. This is conducted as a team of liner specialist, site personnel and liner supplier. The application to the Pustynnoye SAG mill of JSC Altynalmas in Kazakhstan is presented. The increase in liner life by around 50% along with increased mill throughput of over 20% illustrate the huge benefit of the cooperative triumvirate approach through the gains that can be made in productivity and reduced liner costs.CITATION:Powell, M, Kanchibotla, S, Jokovic, V, Hilden, M, Bonfils, B, Musunuri, A, Moyo, P, Yu, S, Young, J, Yaroshak, P, Yalcin, E and Gorain, B, 2018. Advanced mine to mill application at the Barrick Cortez mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 177–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

For many years, underground workings in the Bou Azzer mine have been challenged by geotechnical problems related to the serpentinite instability. The stage of evaluation of the compression potential is crucial to develop an appropriate drilling method and the choice of non-standard support. This research work presents a retro-analysis of serpentinite behavior in underground excavations at different depths, using a multi-approach method, based on several empirical and semi-empirical and theoretical-analytical methods, calibrated by the observational method. The analysis performed in this work reveals that underground excavations in Bouazzer East and Ait Hmane area would encounter compression problems that were recognized as the most serious from a depth of 300 m because of the effects of lithology and tectonics. Therefore, the Aghbar region has a slightly negligible compression potential. The compressive failure mechanism in this mine, depending on the mechanical strength, is started at induced stress of 9 MPa.

Nov 27, 2021

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

By T. Hart

Nuclear gauging is used world-wide in almost every industry. From mining and ore-grading to finished product, the metallurgical industry is one of the biggest users of nuclear sensors for inventory, process control, and quality assurance. This paper will discuss the basic theory of gamma transmission gauging techniques found useful in mining, milling and metal production. Techniques to be discussed are gamma transmission for level and density. A major new technique will also be discussed. This technique is called gamma backscatter. The uniqueness of this technology, how to apply and the differences between transmission and backscatter will be accentuated.

Jan 1, 2011

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017