Search Documents

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By Jack S. Greber

The mining industry generates an estimated 2.3 billion tons of solid waste each year and the total accumulated mineral resource solid waste at both active and inactive mine sites, approaches 30 billion tons. Five industries generate 85 percent of mine solid waste: copper, phosphate, iron, uranium, and coal. Over the past several years, the Federal government has shown increasing interest in the proper disposal of solid wastes generated by the mining industry. Three new pieces of federal legislation have been passed recently beginning with the most comprehensive regulatory authorization passed in 1976, the Resource Conservation and Recovery Act (RCRA) which has been amended to the Solid Waste Disposal Act Amendments of 1980. RCRA is implemented and enforced by the Environmental Protection Agency (EPA) and intended to control municipal and industrial solid wastes. Next came the passage of the Surface Mining Control and Reclamation Act (SMCRA) of 1977 which is implemented and enforced by the Department of Interior to control coal surface mining and the surface effects of underground coal mining, and finally, the recent Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 implemented by EPA and enforced by the Nuclear Regulatory Commission (NRC) to control uranium mill tailings disposal.

Jan 1, 1981

I once read an æarticleÆ in FHM Magazine entitled æThe Coolest Jobs There Ever WasÆ. It was about a group of guys who were pursuing careers that any person on the planet would just kill for. I distinctly remember drooling over the pages, thinking how much I would love to be Michael SchumacherÆs Chief Engineer at Ferrari, or the Principal Designer and Tester for one of the big Dutch rollercoaster companies. From that moment on, I decided that I wanted a career that was cool enough to make it into the pages of that article. Throughout my time at university, I always had that article in the back of my mind. As a result I constantly wondered about what sort of job I could end up with once I left university. More importantly, I wondered if FHM would be banging down my door to put me in the magazine! After a long and stressful job hunting process (in between completing a thesis and studying for exams) I finally managed to land myself a job with Orica Mining Services. I can honestly say I didnÆt know what to expect when I first joined Orica. Most of my friends ended up working for big mining companies, while I was offered a position with one of the biggest suppliers to these mining companies. However, I had a feeling when I was discussing the role with my future supervisor during the interview process that the job was going to be awesome. I have now spent a year working for Orica and I absolutely love it! While I feel that my job is worthy of being in that FHM article, unfortunately, I donÆt think I am going to get my opportunity to be in the magazine. Apparently I donÆt look too good in a bikini! However, I would love to have the opportunity to discuss the journey that I have taken so far û from my time as an environmental science graduate, then moving on to mining engineering, to now, being part of the Orica Mining Services Graduate Program. My suggestion is to use this paper as a resource. I have learnt during my time at university, as well as my time in the workforce, that the best people you can learn from are your peers. Take what you feel is relevant from the paper; hopefully it will help guide you in shaping your own career.

Jan 1, 2005

By Michel G. Grenier

Compliance with Diesel Particulate Matter (DPM) exposure regulation is currently performed using timeweighted average (TWA) sampling on underground mine workers. These samples are collected in the span of an entire shift and the resulting concentrations are compared to a legislated exposure limit. While this is very useful to determine the exposure level of an individual to DPM, it fails to clearly identify causes of exposure and highlight opportunities that could help reduce the exposure of workers in the course of the work shift. Real-time DPM monitoring measures the worker?s exposure as a function of time and helps identify circumstances where corrective actions can be taken or design changes can be made by the individual or the employer to reduce the overall exposure of the worker and peers. This work focused on obtaining DPM concentrations using a real-time polycyclic aromatic hydrocarbon (PAH) monitor. The aim was to demonstrate that this instrument, while not a direct DPM analyzer, was able to provide a concentration profile that could easily be linearly correlated to standard TWA elemental carbon measurements. In addition, several instances of improvements that could be implemented to reduce the exposure of underground employees were demonstrated.

May 1, 2010

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

The 31st annual American Hall of Fame Awards Banquet and Fundraiser sponsored by the Mining Foundation of the Southwest (MFSW) will be held at the JW Marriott Tucson Starr Pass Resort on Saturday, Dec. 7, 2013. Each year, one living inductee, two Medal of Merit recipients, honorees from mining?s past, an industry partnership award, as well as a special citation, are recognized by the MFSW for their respective contributions to the mining industry. James D. Toole, past president and chief executive officer of Southwest Energy LLC, will be the Hall of Fame inductee, guest of honor, and featured speaker at the awards banquet. Toole founded Southwest Energy LLC in 1973 and is credited with introducing innovative explosive technology, providing even greater value to its mining customers. Medals of Merit will be awarded to Joseph M. Keane, principal metallurgical engineer for SGS Metcon Research/KD Engineering, and Sean D. Dessureault, associate professor at the University of Arizona. Keane is recognized for his metallurgical expertise, especially in design development and pollution abatement. Dessureault is recognized for his advanced mining research, with more than 25 journal publications, and his entrepreneurship as the founder and chief executive officer of two mineral-related companies. To honor mining?s past, the hall of fame will induct Bartolomé de Medina for his invention of the patio process for recovering silver; Ben Williams for his management of the Copper Queen Mine in Bisbee, AZ; Charles E. Mills for his contributions at Morenci and Inspiration Copper and founding Apache Powder Co. and The Valley National Bank; John S. Finlay and Edwin B. Royle for their invention of the mucking machine; and Louis Caryl Graton for his ore deposits research and teaching economic geology at Harvard University.

Nov 1, 2013

By Adam Chrzanowski, Eugene E. Derenyi, Peter Wilson

"The rapid growth of the mining industry in Canada necessitates a reevaluation of existing mining surveying techniques and the development of new methods. In this connection, the Department of Surveying Engineering at the University of New Brunswick initiated a research program, and the major points of investigation conducted to date are as follows: 1. Based on practical experience and theoretical studies, all factors influencing classical shaft-plumbing procedures were analyzed. Refined methods were developed to increase accuracy. 2. The performance of electronic and optical distance-measuring instruments in underground conditions were investigated. In this connection, test measurements were made in various mines, employing four types of Tellurometers, two models of Geodimeters and a proto-type optical range-finder. 3. Tests were conducted and methods developed for the mapping of large underground chambers by photo-grammetric means. The aforementioned points are discussed at some length in the paper. The authors have also indicated areas where further research is needed and suggested ways and means to improve and modernize mining surveying as a whole throughout Canada."

Jan 1, 1967

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By J Lapwood, S Pal, M Pascoe

The devastating failure of Dam I at the Corrego do Feijao iron ore mine near Brumadinho in Brazil on 25th January 2019 left at least 270 people dead or missing. In the immediate aftermath of this event, many mining companies commenced reviews of their tailings and water storage facilities (T&WSFs), and Rio Tinto was no exception. Rio Tinto has an interest in over 250 T&WSFs across 47 sites in 13 countries as owner-operator, as managing JV partner, and through non-managed partnerships and other ownership arrangements; T&WSF experts from Rio Tinto’s Surface Mining Centre of Excellence visited the sites in order to complete Technical Risk Reviews of each facility. These reviews looked beyond the day-to-day operational aspects of T&WSF management, and the site’s compliance with local regulations and Rio Tinto’s internal D5 Standard – Management of tailings and water storage facilities, in order to provide a strategic, second line of assurance perspective. The reviews focused on design and construction; operational controls; risk control framework; and competencies and capabilities of personnel involved in the design, operation and closure of the facilities. Additional activities were carried out in parallel with these reviews, including the development of a consistent approach to dam break studies; the public disclosure of information on Rio Tinto’s tailings storage facilities and their management; and contribution to external programs such as the initiatives being co-ordinated by the International Committee on Mining and Metals. This paper provides an overview of the tailings and water storage assurance work undertaken by Rio Tinto’s Surface Mining Centre of Excellence Tailings Validation Taskforce to date; work that will continue to improve governance and assurance for all of Rio Tinto’s T&WSF.

Jul 1, 2021

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By K. Honkivaara, S. Junnikkala, J. Aho, K. Föhr, P. Lampinen

"Bubble area flux has been claimed to be a major tool to dimension flotation equipment. The paper describes laboratory scale (batch and 301 continuous cell using plant feed) and small-scale (1 ,8m3) industrial experiments with coarse-grained massive sulphide ore.Samples were taken with different froth thickness and air addition rates while the bubble size was measured with an UTC capillary device. Problems of averaging the bubble size measurements and the bubble area flux measurements are also discussed.Material balances were calculated using the commercial program BILCO. The flotation rate constants were calculated for pulp and for froth assuming that we can extrapolate the flotation rate constant of the pulp phase from tests using very thin froth thicknesses.The results indicate that the bubble area flux is not alone an adequate dimensioning tool. With fine sizes there was a nearly linear relationship between the bubble area flux and rate constant for constant impeller revolutions. For coarse sizes the form of the relationship is non-linear and seems to go through a maximum value. Thus the final flotation outcome is not a simple function of bubble area flux but depends on the particle size distribution and other more traditional flotation cell dimensioning variables. The effect of the froth residence time in the total recovery of coarse particles is large, but will not be treated in this paper."

Jan 1, 2000

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 3, 1985

By J Joy, A Bye, G V. Kizil

This paper demonstrates an application of a recently developed Risk-Cost-Benefit (RCB) Framework to environmental risk management in the mining industry. The environmental application of the RCB Framework as part of an ACARP project (Kizil, Bye and Joy, 2012) involved a thorough selection process with site visits and in-depth discussions with the case study siteÆs environmental management team. Under their guidance, the highest risk of environmental impact at the case study site was identified as æroad subsidenceÆ at the time when the project work was undertaken. This paper presents the unique application of the RCB Framework to examine the risk of mining-induced subsidence and its impact on one of AustraliaÆs busiest highways, with a traffic volume of 38 000 vehicles per day (NSW RTA AADT, 2008). The RCB Framework was employed to assess the optimum group of controls for road subsidence risk management to ensure highway availability while mining occurs. Whilst this paper focuses on road subsidence, the methodology employed can be directly applied to other environmental concerns including preparation for mine closure, rehabilitation planning and waste management. The RCB Framework incorporates mathematical modules which were developed to enable complex yet tightly integrated RCB calculations. The process integrates the risk-control effectiveness assessment to determine that the selected safety initiative is financially beneficial to the mine site and company. This concept has been applied to a number of high-risk mining areas targeting safety, productivity and environmental issues. This paper introduces the five-staged RCB Framework, incorporating the RCB tools RCBGEN (Risk-Cost-Benefit Generator) and RCEMETHOD (Risk-Control-Effectiveness Method), and demonstrates its practical application to the risk management of a road subsidence case study. The case study looks at potential pavement damages, in particular, the occurrence of pavement stepping on the surface of the highway as a result of vertical subsidence. This type of road damage was previously experienced at another major inter-city route while underground mining occurred in the region where the case study site is located. The RCB Framework has been successfully applied to the analysis of the road subsidence case study and determined the risk reduction and financial benefits of implementing a range of risk-controls. User-friendly RCB Charts to provide an aid for decision-making were produced. The value of using the RCB charts to achieve balance between risk, cost and productivity in the decision-making process for risk management has been explained. The case study determined that pavement slots and fibre-optic cable monitoring were relatively low-cost and effective controls applied in the mining industry for the first time at a global level.This paper supports the industryÆs ongoing efforts to manage risk to ALARP (as low as reasonably practicable) and achieve æzero harmÆ by providing a new Framework to more effectively establish the adequacy of controls.CITATION:Kizil, G V, Bye, A and Joy, J, 2012. Application of risk-cost-benefit analysis to highway subsidence due to mining, in Proceedings Life-of-Mine 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A. L. Peyton

Manganese-oxide minerals occur in irregular pockets distributed through the residual clays of the Cartersville district, which lies 45 miles north-west of Atlanta in Bartow County, Ga. The district produces, or has produced, limonite, barite, specular hematite, ochre, ferruginous manganese, manganiferous iron are, as well as manganese. Bureau of Mines engineers have visited the district on three occasions - in December 1939, February 1941, and October 1942. During the visit of February 1941, 80 tons of samples of manganese-bearing clays were taken from seven properties for ore-dressing tests, which were conducted at the Bureau of Mines laboratory at Rolla, Mo. The. October 1942 visit was for the purpose of reappraising the district in the light of knowledge gained from the ore-dressing studies and to prepare a plan for the district's development. Exploratory drilling was begun in March l943 and was continued until June 1945. Nine properties were explored that, roughly follow a line beginning near Cartersville and extend to a point 2 miles northeast of the village of White. The work consisted of bulldozer trenching, rotary bucket churn drilling, sampling, and analytical determinations. The manganese district is 18 miles long with a maximum width of 7 miles at Cartersville, which lies at the center of the district. The work of the Bureau was confined to the northern half of the district between Cartersville and Pine Log. The properties explored comprise but a small portion of the Potential producing area.

Jan 1, 1949