Search Documents

By L. C. IlsLey

The United States Bureau of clines has been conducting Investigations of electrical equipment during a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 2C, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967

By Terry J. Close

In 1985, at the request of the U.S. Bureau of Land Management, the U. S. Bureau of Mines studied part of the 56,623-acre South McCullough Mountains Wilderness Study Area (NV-050-435) in order to evaluate its identified mineral resources. The area studied is located in Clark County, NV, about 30 miles southwest of Boulder City. No mineral resources were identified. The study area contains the eastern part of the unorganized McCullough Mountain (McClanahan) mining district which has had no recorded production. Between 1911 and 1982, 23 lode claims were located in the part of the mining district that is in the study area; four of these claims are currently held by assessment (1986). A total of 11 mineral sites were found and examined during the U.S. Bureau of Mines investigations; 26 mine workings were examined. Of the 11 sites, four are within the study area, and seven are nearby. Of the seven nearby sites, six are adjacent to the west boundary and consist of precious-and base-metals bearing vein occurrences in metamorphic rocks. The seventh site is near the east study area boundary, and consists of a tungsten-bearing vein occurrence that is also in metamorphic rocks. The four sites within the study area consist of vein occurrences in metamorphic rocks that contain silver, gold, arsenic, lead, zinc, and copper. The veins at these four sites are too small and low grade to be classified resources; however, there are indications that three of the sites may have silver and gold resources at depth. Detailed delineation of the veins, and determinations of tonnages and grades are needed. This would entail additional mapping and sampling, trenching and drilling, and opening inaccessible workings.

Jan 1, 1987

By Emil B. Milosavljevic

Problems associated with distillation and other classical methods for analyzing operationally defined cyanide (CATC, WAD, Total and Free Cyanide) will be discussed. These methods often achieve incomplete, species dependent cyanide recoveries and suffer from serious interferences. Depending on the relative concentrations of interferents and other matrix constituents, underestimation (ultimately Type II errors probability of not detecting a constituent when it is actually present) or overestimation (ultimately Type I errors -probability of deciding a constituent is present when it is actually absent) of the cyanide levels present in a ,given sample may occur, causing in the first case false security and in the second case, excessive cyanide treatment costs. Mahy, if not all, enumerated problems can be solved by using novel flow injection (FI) gas-diffusion amperometric methods. A modification of the recently approved FI ligand exchange (FIILE) method for determination of available cyanide (USEPA Method OIA-'l677) that obviates sulfide interference will be discussed. Eight laboratory round-robin data obtained for the FI UV -digestion (FIIUV) method that determines total cyanide (Proposed Method OIA-1678) will also be presented. In addition, some methods for cyanide speciation will be presented. Finally, research needed for developing reliable methods for determination of operationally defined cyanide in solid samples will be summarized.

Jan 1, 1998

By Willard P. Ward

The numerous direct processes which have been patented and brought before the iron-masters of the world, differ materially from that now introduced by Mr. Wilson. After a careful examination of his process, I am convinced that Mr. Wilson has succeeded in producing good blooms from iron-ore, and I think that I am able to point out theoretically the chief reasons of the success of his method. Without going deeply into the history of the metal, I may mention the well-known fact, that wrought-iron was extensively used in almost all quarters of the globe, before pig or cast-iron was ever produced. Without entering into the details of the processes by which this wrought-iron was made, it suffices for my present purpose to say that they were crude, wasteful, and expensive, so that they can IE employed to-day only in a very few localities favored with good and cheap ore, fuel, and labor. The constructiou of larger furnaces and the employment of higher temperatures led to the production of a highly carbonized, fusible metal, without any special design on the part of the manufacturers in producing it. This pig-iron, however, could be used only for a few purposes for which metallie iron was needed; but it was produced cheaply and with little loss of metal, and the attempt to decarbonize this product and bring it into a state in which it could be hammered and welded was soon successfully made. This process of decarbonizatioa, or some modification of it, has successfully held the field against all, so-called, direct processes up to the present time. Why ? Because the old-fashioned bloomeries and Catalan forges could produce blooms only at a high cost, and because the new processes introduced failed to turn out good blooms. Those produced were invariably "red-short," that is, they contained unreduced oxide of iron, which prevented the contact of the metallic particles, and rendered the welding together of these particles to form a solid bloom impossible. The process of puddling cast-iron, and transforming it by decarhonization into wrought-iron has, as everybody knows, been in successful practical operation for many years, and the direct process referred to so closely resembles this, that a short description of the theory of puddling is not out of place here.

Jan 1, 1884

By L. C. George

The Bureau of Mines measured vapor pressures of selected mixtures in the binary system SnCla-ZnC12 by the static pressure method. Equations expressing the vapor pressure) and the heat and free energy of vaporization) as functions of temperature were developed by numerical analysis based on the sigma-plot method. It was found that the vapor pressure of any SnCl2-ZnCl2 mixture) at any temperature within the range of this investigation) could be accurately calculated from the derived values for the heat and free energy of vaporization for the mixture, with a probable error of 0.01 cm Hg or less.

Jan 1, 1967

By Viviane Tavares

The liquid crystal display (LCD) are currently known by its vast application in electro ? electronic devices, amongst them can be detached the devices of TV, laptops, electronic date, calculators and even though the mobile telephones (mobiles). The mobiles are changed more frequent of the TV for example, this happens due to the technology advance. With the constantly mobile exchange, the batteries, printed circuit board and liquid crystal display accumulation its become an environmental problem. To minimize the environmental impacts caused by mobile telephones residues are considered the segregation process of the LCDs main components, to goal to recover the recycle material. This process involves the use of treatment ore techniques with disc, hammers and balls mills. The process with best efficiency (about 98%) of LCD glass release was the hammers mill. The glass recovered can be used in the glass recycling and the sand substitution in the production of concrete blocks.

Jan 1, 2009

By Trevor R. Ellis

The extractive industries addition to the International Valuation Standards (IVS) is scheduled for publication in the next edition of the IVS book in January 2005. This will provide guidance for valuation of minerals and petroleum industry assets of all types for all appraisal uses. It will provide asset valuation support to the International Financial Reporting Standards for the stock markets of the world, and a global umbrella standard which can be supplemented for local needs by institutes and regulators. This paper discusses implementation of the IVS within the minerals industry and important issues that the industry should confront.

Jan 1, 2005

Andesites are a major source of aggregate for much of the North Island of New Zealand. There are regional differences with respect to some important properties of the andesites. Some are reactive with cement and are designated as potentially deleterious or deleterious by the concrete industry. Other andesites, particularly those that are slightly altered or weathered, have rather high Plasticity or Clay Indices and perform poorly in road construction.   The performance of the andesites has been investigated and can be shown to be determined by: +        the chemistry of the rock which in turn determines the chemistry of the glass in the rock; +        the presence of large amounts of groundmass glass in the rock; and +        the nature of the superimposed alteration processes. Environment of extrusion and how rapidly the rock has been cooled or chilled are also important as they determine the fabric of the rock and how much glass will be present in the rock.   There are three main types of alteration that affect the quality of the aggregate: 1.   hydrothermal alteration, 2.   late magmatic alteration associated with the devitrification of glass, and 3.   weathering.   Each of these alteration types produces different alteration minerals. In fresh andesites the devitrification of glass has an important affect on the rockÆs properties. The Taranaki andesites are shown to have unusually (in comparison with other North Island andesites) high Na2O contents, held in the groundmass glass, which is the fundamental reason for the high alkali û silica reactivity of these andesites.

Jan 1, 2005

By Ron Ketterling

We will discuss electronic and paper record keeping, what works and what doesn’t. We’ll review record keeping in light of those five sub-committees: Audit, Awards, Constitution, Ethics and Planning. You’ll come away with concrete steps you can use to improve your record keeping processes

Feb 1, 2020

By Jack Bedder, Nils Backeberg

"Native antimony metal is rare and antimony generally occurs together with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main economic mineral.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. While China remains the leading primary producer, accounting for 69 percent (80.5 kt or 88,700 st) of the global 117.5 kt (129,000 st) in 2017, market consolidation and regulatory inspections across China leading to closures of facilities have caused a significant decrease in Chinese output from 115.8 kt (127,600 st) in 2015 (81 percent of global production).Tajikistan and Russia are the next largest producers of antimony after China, both ramping up production in recent years. Russia could significantly increase its supply of antimony if Polyus moves ahead with supplying 10-12 kt/a (11,000–13,200 stpy) of contained antimony from gold tailings. Australia and Bolivia are also significant mine producers outside China. The value of the different ores varies based on the metal content of the concentrates, with the most valuable gold-bearing ores sourced from Australia’s Costerfield Mine and the least valuable mercury-bearing ores sourced from the Anzob Mine in Tajikistan. On average, Bolivian and Russian ores trade at an intermediate value between those from Costerfield and Anzob. Nearly all of the rest-of-world production is exported to China, where the ores and concentrates are processed into antimony ingots and oxides.Antimony ingot production is not as widespread as is the case with antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries ,such as Vietnam and Myanmar, where environmental legislation has historically been less stringent. Tajikistan has become a growing producer of antimony ingot since 2014, coming from the commissioned metallurgical plant at the Anzob Mine.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe (mainly Belgium and France), which relies on imported antimony metal feedstock, mostly from China.A new antimony project under construction by Strategic and Precious Metals Processing (SPMP) in Oman made progress in 2016 and 2017, and after producing first metal in April 2016 in test facilities, was set to be commissioned in the first quarter of 2018. Commissioning had been moved back to June 2018, with a potential ramp-up to 2-3 kt/a (2,200 to 3,300 stpy) of antimony metal by the end of 2018. SPMP is also reviewing producing antimony oxide as part of its flow sheet."

Jan 7, 2018

By Dale A. Sketchley

The objective of Quality Assurance and Quality Control programs on advanced exploration projects is to ensure that data from sampling, assaying, and recording of geological observations are of high integrity for the purpose of obtaining reliable mineral resource and reserve estimates. National Instrument 43-101 Standards of Disclosure for Mineral Projects states that all scientific and technical reports must be prepared and certified by a Qualified Person in accordance with professional and industry standards following Mineral Exploration Best Practices Guidelines and Definitions, and Guidelines of the CIM Standards on Mineral Resources and Reserves. Additional information is given in Companion Policy 43-101CP and Technical Report Form 43-101F1. Although the Qualified Person must discuss and describe the Sampling Method and Approach; Sample Preparation, Analyses, and Security; and Data Verification; there is little specific information in the guidelines on Quality Assurance and Quality Control programs. Examples from the Oyu Tolgoi Cu-Au Project are given for optimizing sampling protocols, following proper sample preparation procedures, safeguarding sample shipments through chain of custody, ensuring quality of assaying with Round Robin monitoring programs, verifying transcribed data, and validating data with check assays to ensure high integrity for resource and reserve estimation. Oyu Tolgoi, also known as Turquoise Hill, is in the South Gobi desert, Mongolia, about 550 km south of the capital city of Ulaanbaatar, and 875 km northwest of Beijing, China. The project covers a major copper-gold system, which consists of the South West, South, Central, and Far North deposits, comprising high sulphidation and porphyry mineralization with oxide, supergene, and hypogene ore types. Exploration is done by multiple diamond drill rigs, and samples are prepared on-site and shipped to laboratories in Mongolia, Canada, and Australia for further preparation and analysis.

May 1, 2003

By Arild Palmström, Castro Fresno

El presente trabajo se enfoca en la información recolectada a partir de testigos de perforación diamantina, dejando de lado cualquier otra fuente de información como serían los afloramientos rocosos, laboreos subterráneos, estudios geofísicos, ensayos de laboratorio o de campo, etc. Cuando consideramos un formato de logueo geotécnico de perforaciones diamantinas, primeramente debemos evitar la utilización de formatos extremadamente grandes y complejos, no se necesita recolectar una gran cantidad de información, se necesita recolectar la información necesaria.

Sep 1, 2017

By A. A. Schweizer

This paper documents the growth and projects the future of Green Diamond Sand Products. Since1954, Green Diamond, located in Riddle, Oregon, has been producing sand from granulated nickel slag for use in various markets. Through the years, the company has seen several changes from its ownership to its product lines. In 1991, Green Diamond was producing abrasive sand at a rate of about 30,000 tons per year. It was at this time that Green Diamond became part of Glenbrook Nickel Company. Over the next eight years, Green Diamond would quadruple its production to over 140,000 tons while moving into three new markets, as well. Green Diamond is now producing sand for use in the abrasive, foundry, construction, and roofing industries. In 1998, Green Diamond again found itself under new, private ownership. With plans on developing agricultural sand and spent abrasives recycling, the future of Green Diamond appears to be one of further expansion coupled with diversification of its product lines.

Jan 1, 2000

By HENRY COLEMAN

WE as employees of these related companies, I am sure, are proud to be affiliated with them, and have great faith in the sagacity and fore- sightedness of our employers. Most of us here have been called into important positions in these organizations, and it should be our most earnest endeavor to sense and carry them out as if they were our very own. We have been asked to supervise and carry on a work over which our employers cannot personally watch. It has been well said that the most efficient organization is that which requires the least attention from its head. Because of the very nature and condition of our work, which separates us by many miles from our employers and makes it impossible for us to receive attention and instructions from the heads of our departments, save for occasional visits and correspondence, we are given a great opportunity to prove that we can be efficient workers without too much attention from the heads of our departments. There are few employees who cannot do their duty when it is laid before them in specific terms, and when their employers are always there to see that their plans are carried out. But the employee who is really giving efficient service sees his duty himself and willingly does it. '

Jan 1, 1931

By Adriaan van Seters

"Abstract The content of Eurocode 7 – Part 1 and Part 2 – with respect to piled foundations is outlined. The important role of pile testing is presented and the derivation of the characteristic value of pile bearing resistance is explained. Recommendations for the use of correlation factors are given. The ongoing work of the Evolution Groups on piling is to prepare a revision of Eurocode 7 after 2019. Future topics and changes are highlighted.General outline of pile design by Eurocode 7In his paper for this conference Frank (2014) outlined the various aspects of standardisation for pile foundations, which involves Eurocode 7 as leading for pile construction in Europe. Standards for pile testing and execution of piling works were established in the last 15 years.This paper focuses on the design of piled foundations according to the design code Eurocode 7, which consists of 2 parts:EN 1997-1 Geotechnical design - Part 1: General Rules (CEN, 2004);EN 1997-2 Geotechnical design – Part 2: Ground investigation and testing (CEN, 2007) In Eurocode 7-1, Section 7 – Pile Foundations - deals with the design of piles. The safety concept for pile design is given in Section 2 – Basis of Geotechnical Design - for the three Design Approaches.In Section 7 presents the design of piles according to four methods:1. Results of static load tests2. Empirical or analytical calculation methods3. Results of dynamic load tests4. Observed performance of a comparable pile foundation.Guidelines for the ground investigation for piles is provided in Eurocode 7-2, Annex B.3. In the Annexes of Eurocode 7-2 examples of analytical methods to determine the bearing resistance of a single pile based on the results of various ground investigation techniques are given. Thus calculation models are presented based on design using the results of Cone Penetration Tests (D.6 and D.7) and Pressuremeter Tests (E.3). The Annexes of Eurocode 7-2 are informative.For the interpretation of Eurocode 7, reference is made to Frank et al (2004) and Bond and Harris(2008)."

Jan 1, 2014

By S Mundell, J Armstrong, M Evans

"Automation is a common goal within the coal industry for reasons such as efficiency, reliability and sustainability. However, it requires standards and frameworks so business systems can communicate effectively. Automation of sample analysis processes has been difficult to establish due to a lack of direct business system communication between commercial laboratories and mining companies. This has resulted in manual procedures that have contributed to problems relating to analysis instructions, sample identification, results formats and visibility of status.These problems result in loss of data and confidence in data validity, loss of process efficiency and inability to react to issues. An Australian Coal Association Research Program project (Evans, Armstrong and Arboleda, 2014) has addressed these issues through the Coal Quality Data Exchange methodology for direct business system communication between coalminers and commercial laboratories to optimise the transfer of coal quality data.The benefits to the coalminer of the framework are:increased clarity and auditability of what is being sent to the laboratory and what was requestedreduced potential for error introduced through manual transcription tasksincreased speed of loading of analytical results to the customer Geoscientific Information Management Systemimproved turnaround time for analytical resultsincreased knowledge about what took place in the laboratory with respect to the determination of the analytical resultsincreased visibility of the status of a ‘work order’. The benefits to the technology companies and commercial laboratories is a common framework on which to build a sustainable solution that gets away from the multitude of formats catered for today and time consuming manual processes. The common framework significantly advances the future possibilities for the automation of sampling and analysis processes in a production environment.CITATION:Armstrong, J, Mundell, S and Evans, M, 2014. Automating communications between laboratories and mines – a case from the coal industry, in Proceedings Ninth International Mining Geology Conference 2014 , pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

"Requests are frequently received by the Information Service of the Bureau of Mines for published information on the coals of different foreign countries, as compared with coals mined in the United States. The analyses of various coals from several countries on the Pacific, which were submitted to the Fuels Division for certain tests between the years 1913 and 1916, may be of interest, and are shown below: Results of Analyses of Various Coals from China, New Zealand, Japan and Australia."

Sep 1, 1925

An Innovative Process for Comprehensive Utilisation of Clay-Vanadium Ores By adopting conventional processing technologies such as flotation, gravity concentration, and magnetic separation, it is difficult to enrich vanadium mineral effectively. At present, vanadium extraction process usually has not the mineral processing enrichment procedure, but rather uses direct hydrometallurgical process: roasting - leaching - precipitating vanadium for obtaining high quality V2O5 product. But it results in problems, for instance, high consume of auxiliary materials like acid and alkali, serious pollution and high cost of vanadium extraction. In the project study on the ore of a certain clay vanadium mineral, by adopting the test process: scrubbing raw ore with reagents added in - dispersing and segregating with reagents - grading enrichment, vanadium concentrate product with higher grade was made by virtue of reagent's selective inhibiting, and the purpose of upgrading the raw material used for vanadium extraction with hydrometallurgical process is achieved. The process technology obtained from project study features simple process structure, low equipment investment, low cost of mineral processing and pollution-free to environment. It provides high efficient and practical technology for the comprehensive utilisation of clay vanadium mineral, and has a prominent prospect for its popularisation and application.

Sep 13, 2010