Search Documents

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

By Doug Scott

Develop tools that companies can use to comply with 29 CFR 1910.1200.

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

By R. B. Sudderth, A. Quiroz G., M. Torres M., C. Salgado Q., J. Fernández O., H. Bravo P., M. Torres B.

SNF FloMin, Inc. has introduced a complete line of extractants for recovery of various metals. Among them are the CuPRO MEX™ Brand of copper extractants that are based on the well- known 2- hydroxy 5-nonylsalicylaldoxime and 2-hydroxy acetophenoneoxime. This paper presents the laboratory and pilot plant trial results for SNF FloMin’s CuPRO MEX™ 3302 reagent, the equivalent to the wellknown ACORGA® M5640 extractant, and the composition of these reagents are described. Some examples of SNF FloMin’s CuPRO-Sim™ Advanced solvent extraction simulator are presented.

Jan 1, 2014

The polymerisation of silica is found to interfere with thickening of leach pulps at Risdon. Hydroxyl ion and fluoride ion are catalysts for this reaction. Stability may be obtained by the presence of aluminium or ferric iron.INTRODUCTIONAt Risdon it has been a matter for satisfaction that, although the concentration, of silica in leach solutions is appreciable, it has ,given relatively little cause for anxiety.However the margin of safety is small and some intermittent difficulty in thickening leach residues during the last few years has prompted a further investigation, certain parts of which are described here since they may be of general interest.Leaching and ClassificationThe method of leaching which is practised at Risdon has been described in, two previous articles, by W. C. Snow (1936) and S. W. Ross (1949) to whiCh the reader is referred for detail. Continuous leaching is practised, the circuit solution flowing through five air agitated pachucas in series, to tlie first of which calcine is added. The circuit solution, which also enters the first pachuca, consists of spent electrolyte from, the electrolytic cells and contains 90 -gm. of free sulphuric acid per litre. About 80 per cent of the solublezinc oxide is extracted from the calcine in the first pachuca, at a pH value of 1-1 (7 gm.H2S04/1 at 55 to 60°C. In the later pachucas the leaching rate decreases sharply. The leach pulp which leaves the 'last pachuca contains an average of 17 gm. of free acid per litre, corresponding to a pH of 1.7; but, owing to variations in extraction, the end point fluctuates between 2.5 and 0·3 gm. free acid per litre (pH:> 1·5 to 2.5). The average flow through the plant is 1,250,000 gallons per day, which corresponds to a production of 300...

Jan 1, 1958

By Sun Chuanyao, Jia Muxin

Generally, if the bond valence (BV) between metal ion and oxygen of the mineral is greater than 0.8, only surface species –Me-O-H or –Me-O exposures on the mineral interface, if the BV is between 0.2-0.8, the metal ion exposures on the interface, and if the BV is less than 0.2 the metal ion dissolves into water. The PZCs of oxide minerals and island silicate minerals are determined by the bond valence of the bond in the mineral crystals, the higher the bond valence the lower the PZC of the mineral. So the PZC sequence of Al2SiO5 minerals is kyanite> andalusite> sillimanite. The general rule for framework silicate minerals is as: The higher the Al content, the lower the PZC of the mineral, when the ratio of Al to Si in the tetrahedron skeleton is below 1:3. The higher the Al content, the higher the PZC of the mineral, when the ratio of Al to Si in the skeleton is between 1:3 and 1:1. The general rule for layer silicate minerals is summarized as: the three-layer silicate minerals have much lower PZCs than that of the two-layer silicate minerals. The threelayer silicate mineral with the octahedron layer occupied by lower charged cations has lower PZC than that of the three-layer silicate mineral with the octahedron layer occupied by higher charged cations. The twolayer silicate mineral with the octahedron layer occupied by lower charged cations has higher PZC than that of the two-layer silicate mineral with the octahedron layer occupied by higher charged cations. The layer silicate mineral with Al substitution in the tetrahedron layer has lower PZC than that of the layer silicate mineral without Al substitution in the tetrahedron layer. Such pyroxene minerals whose M1 is occupied by a trivalence cation and the M2 is occupied by a monovalence cation has lower PZCs than those both M1 and M2 are all occupied by bivalence cations. Such hornblende minerals whose M2 is occupied by a trivalence cation and the M4 is occupied by a monovalence cation has lower PZCs than those both M2 and M4 are all occupied by bivalence cations. There is no Si4+ or 4 coordinated Al3+ exposures on the surface of framework silicate minerals, the metal ions of three layer or chain silicate minerals are compact between tetrahedron layersor chains, they hinder the metal ions to interact with oleate acid radical, the metal ion octahedron layer exposures on the surface of a two layer silicate mineral, but the the oleate acid radical can not attach to a metal ion by replacing a –OH- that connects three metal cations in the same time, So the floatability of such silicate mineral is bad. The metal octahedron chain style of an island silicate mineral affects it floatability, the mineral exposures octahedron chain metals with two dangling bonds in two directions floats better than the mineral exposures octahedron chain metals with two dangling bonds in one direction.

Jan 1, 2003

By Thomas M. Sweeney

This open-file map is a quick reference containing location, ownership, and general lithology information on 124 active or significant Nevada gold mines. The map includes all counties, significant towns, and major highways in Nevada to aid in mine location. Several geologic trends with which the mines are associated are also depicted. General ore genesis for each deposit, including sedimentary, volcanic, plutonic, and placer-hosted deposits, are also identified. Gold mines are also listed alphabetically, by mine name, on the map. Each entry includes the appropriate county, percent of company ownership, operating company, and the property status as of May 1992. For additional information, contact Thomas M. Sweeney, U.S. Bureau of Mines, Western Field Operations Center, 360 East Third Avenue, Spokane, WA 99202; telephone (509) 353-2700.

Jan 1, 1993

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By R Zhou, B J. Monaghan, S J Chew, R J. Longbottom, D J. Pinson, H Li, P Zulli, G Zhang, L Lu

Steelmakers are increasingly motivated to use iron ore resources with a wider range of grades and mineral types that were previously considered unsuitable or uneconomical for sintering. In this respect, specific issues, which now require further investigation and understanding, include the sintering of ore types with:- overall higher gangue content- elements that cause problems in the steel manufacturing operations- distinctive sintering performance compared with traditional hematite-rich iron ores. Laboratory-based investigations of the sintering performance and the behaviour of gangue impurities during sintering is an important step towards the successful utilisation of these resources in steelmaking.In terms of laboratory-based sintering investigations, there are two generally accepted experimental scales utilised prior to undertaking industrial-scale trials, which include: bench-scale tablet (compact) testing and pilot-scale pot testing. The former has the advantages of flexibility and more precise control of sintering conditions; but it is difficult to simulate the heterogeneity of a sinter bed. The latter, which is carried out in pots with diameters between 150–500 mm, simulate the commercial sintering process and conditions quite well, but is time-consuming and labour-intensive due to operational complexity. It is therefore desirable to establish a smaller scale pot testing facility that avoids the disadvantages of the normal sintering pot but can provide comparable information.To explore the feasibility of small-scale pot testing, a ‘millipot’ facility was established to examine the sintering performance of iron ores and other non-traditional ferrous materials. The millipot has a diameter of 53 mm and height of 400 mm. The facility has the capability to monitor the sintering temperature at a number of locations (axial, radial) within the sinter bed and to adjust the suction (‘windbox’) pressure. This paper describes the development of the millipot facility and operational procedures, together with initial tests undertaken in order to match its performance with industrial sintering performance.CITATION:Li, H, Zhou, R, Pinson, D J, Zulli, P, Lu, L, Longbottom, R J, Chew, S J, Monaghan, B J and Zhang, G, 2017. A millipot set-up for sintering investigation of iron ores, in Proceedings Iron Ore 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By E Jak, M Shevchenko, E Nekhoroshev, D Shishin

In the field of pyrometallurgy, the presence of multiple molten phases with distinct chemical compositions, such as slags, mattes, speiss liquids, metals and molten salts, is a well-known phenomenon. These phases exhibit strongly non-ideal solution behaviour and are mutually miscible to varying degrees. To describe these complex molten liquids, the Modified Quasichemical Model (MQM) has proven effective and has been applied to numerous binary, ternary and several higher-order multicomponent systems related to pyrometallurgy. In recent decades, the complexity of high-temperature processes has escalated due to increased impurity concentrations in primary ores, the incorporation of recycled consumer products and the integration of metallurgical plants through by-product and waste exchanges. To address these issues, PYROSEARCH laboratory has been developing large 20-component thermodynamic database using a generalised CALPHAD (CALculation of PHAse Diagrams) methodology integrated with experimental investigations. Over the past decade, strategic decisions were made balancing the ability to generate experimental data, prediction power, accuracy, stability of calculations, as well as computational time, which are discussed in the paper. Examples provided for issues of >3 liquid immiscibility, non-ionic behaviour and exaggerated ‘sharp’ enthalpies of mixing in silicate slags, dealing with multiple oxidation states, as well as comparative analysis of pair and quadruplet approximation in MQM.

Aug 21, 2024

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on’ any standard PC.

Jan 1, 1998

By James Westfield

Following is a brief history of Bureau of Mines Division of Coal-Mine Inspection activities that have favorably effected health and safety and reduced Injuries at coal mines: The Federal cline Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines for the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consulting with representatives of management and mine workers, and was incorporated in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, betweeen the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines considered imminently dangerous, but authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1962

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023

By J L. Mauk

The Favona low-sulfidation epithermal deposit in the Hauraki Goldfield is less than one kilometre southeast of the world-class Waihi deposit. The veins are hosted by Miocene andesite of the Waipupu Formation, have a total strike length of over 900 m, a vertical extent of at least 350 m and are on average 1-3 m wide. Individual veins have been traced for 200 m with vein widths up to 25 m. The dominant vein textures are massive, crustiform and colloform banded veins and vein breccias, with subsidiary textures including comb, zonal, flamboyant, lattice-bladed, ghost-bladed, microbotryoidal, feathery, ripple and dune, and mosaic. Quartz is the dominant gangue mineral in the veins at Favona. Accessory gangue minerals include pyrite, chlorite, adularia, illite, calcite, and apatite. Electrum is the only gold-bearing mineral and is associated with acanthite, tetrahedrite, pyrite, sphalerite, chalcopyrite, and rare galena. Whole rock geochemical analyses indicate that gold grades correlate with textures/vein types. The highest gold and silver grades are associated with vein breccias and banded veins, with the former containing 28 g/t Au and 136 g/t Ag on average. To date, veins with significant base metal sulfide minerals, and massive and crystalline quartz veins lack significant precious metals (Au and Ag), except for one banded base metal sulfide-rich vein at Favona. An overall zonation of the veins exists, with base metal sulfide minerals dominant at depth (1050 m RL) of the system are characterised by massive quartz veins.Fluid inclusions from a total of 31 quartz, amethyst, and platy calcite veins reveal homogenisation temperatures of ~190-250¦C, with final ice melting temperatures between 0.0 and -0.8. Ice melting temperatures correspond to apparent salinities of 18O value of the water that formed these veins is approximately -4.3 per mil, which is similar to meteoric water-dominated, near neutral chloride fluids in geothermal systems in the Taupo Volcanic Zone.

Jan 1, 2002

Development of Grindability Tests Based on Direct Measurement of Energy Nowadays, for the characterisation of the grindability different grindability indices - Bond-work index (Wi), Hardgrove Grindability Index (HGI) or Zeisel specific grindability (Wt) - are used. Generally, the grindability tests are carried out under relatively simplified circumstances, in a special dry batch mill with defined feed size material until prescribed conditions are reached at room temperature. However, in the fine- and ultra fine grinding, which is a frequent task (fly ash, tailings, alumina, etc), a fine material (<50 - 200 ¦m) is usually ground down to the few micrometers. The conventional grindability testing methods and apparatuses (Bond-, Hardgrove-, Zeisel-processes) for their determination, although, are not suitable directly to measure the grindability of such fine materials, since the maximal particle size of the feed material (0.5 - 3 mm) to be tested is much higher. One of the important goals of the research carried out in our Institute was to develop the novel grindability testing methods, which are suitable for the fine and ultra fine grinding, and additionally provide the possibility for the fast determination of the grindability. In order to realise the above aim the conventional Bond- and Hardgrove- mills were modified in order to directly measure the grinding work. In particular, the Hardgrove-mill was equipped with a simple torque-meter (load cell). The Bond-mill was rigged with a digital electric power measurer. The systematic experiments were carried out parallel in both mills using the conventional and the developed methods. Finally the results of both were compared. The measuring results have proved that the Bond-work index can be determined based on the developed methods. The new grindability testing methods were applied successfully in several industrial research tasks for the determination of the specific grinding energy and the Bond-work index. These methods can be also used in the industrial practice for the control of the grinding process.

Sep 13, 2010