Search Documents

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By Q. Zhang

The necessary capability of the gravity transportation pipeline system for cemented coal gangue backfilling at the Suncun Coal Mine, China, is about 74.4 m3?h-1 according to mining production and working times in the mine. It is estimated that the working velocity and maximum pipe length-backfill depth ratio of the backfill system are 3.82m?s-1 and 5.4, respectively and that the probable backfill capability of the system is 110.18m3?h-1. Results of hydraulic calculations for the backfill transportation system show that the designed backfill system is reliable in flowability and sufficient for backfill capability needs.

May 1, 2007

By Raffaella Granata, Wesley Schmutzler, Matteo Bertoni

"The Lower Wood River Levee system, at the confluence of the Wood River Creek and the Mississippi River, in East Alton, Illinois, has been plagued with underground seepage and, in 2010, remediation was deemed necessary by the Southwestern Illinois Flood Prevention District Council and the United States Army Corp of Engineers (USACE). The experts enlisted by the council produced a design that provided for constructing a cutoff wall approximately 2,000 feet long and up to 140 feet deep, through alluvial and outwash soils, and embedded in bedrock. This paper will describe the challenges faced by the Quality Control (QC) and Quality Assurance (QA) teams due to the complex nature of the project in conjunction with an extremely thorough QC/QA program.INTRODUCTIONThe “American Bottom” is an area of 453 km2 (175 square miles) in Southwestern Illinois, extending from Alton south to the Kaskaskia River, which is home to 156,000 people. In the 1940s and 1950s the U.S. Army Corp of Engineers (USACE) designed and built a 120 kilometer (74 mile) long levee system to protect the area from a 500-year flood event on the Mississippi River, which flows through it. The levee system has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed.The Southwestern Illinois Flood Prevention District Council (SIFPDC), to obtain Federal Emergency Management accreditation, in June 2010 commissioned a team lead by Amec Foster Wheeler for the design and management of the required levee improvements. The team presented in 2011 the project’s first set of drawings showing proposed design features throughout the levee system. The project was subdivided in four areas, based on the controlling levee districts, one of which, the Wood River Drainage and Levee District, was split into three subdivisions: Upper Wood River, East-West Forks of Wood River, and Lower Wood River.The project included the installation of a cutoff wall at the confluence of the Wood River and the Mississippi River in East Alton, IL (Fig. 1). The Engineer of Record (Amec Foster Wheeler) considered the cutoff wall as the only viable solution to stop the severe under-seepage that was undermining the integrity of the Lower Wood River Levee. The Lower Cutoff Wall (LCW) project is the subject of this paper."

Jan 1, 2017

By R. L. Amelunxen

"In January 1983, Gibraltar Mines Ltd. started an exploratory program on Column Flotation with hopes of improving performance of the Molybdenum Cleaning circuit. The encouraging results led to a column test trial in the Bulk Copper Cleaner circuit where the test unit has per¬formed well. A program was undertaken to understand the mechanics of column operation. A year and a half later, Gibraltar is considering the replacement of existing Bulk Copper and Moly Cleaning flotation cells with a fully computer con¬trolled Column Flotation circuit.BRIEF SUMMARY OF TESTWORKInitial testwork was done with a home made 20 inch diameter x 31 foot high column, equipped with a doppler flow-meter at the tail line and automatic level conrol. This loop maintained constant level in the column by throttling the tail valve. This column was placed in a variety of locations around the Moly circuit as shown on Figure 1 a, b. Test re¬sults indicated that the column could achieve much higher grades than the conventional cells, but recovery wise, the performance was low. Spillages from overloaded pump boxes were a common frustration during this time.Column control strategy was reviewed; and, in light of information received from McGill University, changed to conform with the methods that had been employed by D. Wheeler, of the Column Co. of Canada4 and Gaspe Copper Mines3.The column was tested replacing a portion of the bank, figure lc. The results obtained were more or less equal to the circuit. However, as we had Nitrogen gas connected to the column and not the regular cells, the column was kept in service. With the use of Nitrogen in the column, the usual copper depressant, Sodium Cyanide could be replaced with Sodium Hydrosulphide, hence lower operating cost.As time went on, a 10 inch diameter column was added in series to re-treat the concentrate of the 20 inch diameter column with hopes that the copper content would decrease from 0.6% down to 0.3% in order to save on subsequent leach¬ing costs. So far, results indicate there has been some im-provement, hut we are not achieving 0.3% copper. (See figure 1d)."

Jan 1, 1985

By G. Balletto, C. Furcas

"The mineral raw materials industry is a key-component of the Gross Domestic Product of industrialised economies, closely related to both the building and the industrial sectors. Despite this, at local level mining and quarrying are associated with both irreversible environmental damage and several visual alterations affecting the natural landscape. In this sense, SIA (Social Impact Assessment) has become a strategic tool that can not only improve the prediction but also the assessment of the social impact by involving the local communities in a participatory process. Taking into account the SIA experience, together with the examination of some relevant international case studies, it is possible to draw up a list of good practices for mining project management, from exploration through to closure and beyond, with quarry restoration. Such good practices will complement the existing studies, focusing on environmental issues, with the social issues arisen considered in SIA application."

Jan 1, 2011

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameters like commodity price, mining or processing cost, stripping ratio etc. The most important characterization of these push backs is that the inner most push back has the highest value per ton, the second inner most push back has the second highest value per ton and so on. These nested pits are generated based on the best estimates of grade within a representation of the ore body in a three dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduced a new algorithm that incorporates ore grade uncertainty during push back design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence.

Jan 1, 2007

By Janet M. Epps

The international climate regulating environmental management in mining is rapidly evolving through the combined influences of the development of international guidelines, resolutions, protocols, treaties and conventions; the influences of the international lending and aid institutions who seek a consistent but constantly evolving standard of environmental performance from their clients; the legal precedents being developed in courts al over the world; and the activities of multinational countries who tend to rapidly upgrade technological performance through their international activities (particularly influencing developing countries). In this rapidly evolving regulatory environment, the more 'models' available to this international pool of resource materials that demonstrate practical. cost-effective and (most desirably) incentive based regulatory mechanisms, the better will be the eventual body of 'international standards' we will al have to work with. Australia can make a significant contribution to this process, however, it has only been on the margin of this dynamic, North American and European led process, up to this time. It is in the Australian minerals and energy industry's best interest to take an active part in the evolution and direction of this process.

Jan 1, 1996

By R. D. Lawrence

"Comparable transaction analysis is the best known of the market approaches to valuation of exploration-stage mineral properties. The analysis of option and farm-in agreements can also provide useful guidance to valuators. While such approaches can be distorted by incomplete analysis, market-based methods are capable of providing consistent, credible results when carried out carefully with due consideration paid to all factors which buyers and sellers consider when dealing in the real market. IntroductionMineral properties without defined resources present one of the most challenging tasks to the mineral valuator. This paper will concentrate on market-based approaches to valuation of such properties. Other authors at MM2000 presented papers on cost and income approaches. Sorentino (2000) also provides a useful overview with some provacative commentary on methods.Market based-approaches are based on the principle of substitution and include such techniques as: comparable transaction analysis (sometimes referred to as sales comparison analysis); farm-in commitment (or option agreement) analysis; rules-of-thumb; and comparable market value analysis.Are there any valuation standards available to assist the valuator? In Canada there are none that apply to the valuation of mineral assets or securities. This problem is being addressed, at least in part, by the CIMVal Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM)1. Further, the recently established Canadian Association of Mineral Valuators will be giving consideration to the adoption of valuation standards."

Jan 1, 2002

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By Craig Naudé

"An enhanced gravity concentrator was installed in conjunction with an Intensive Leach Reactor at the Sadiola plant in Mali last year and commissioned in Dec 2007.There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every 10% of gold recovered by gravity, there was a corresponding 0.1% to 1% additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall 4% gain in plant recovery.With total gold recovery of 12% in the gravity section, grades are increased from 3.54g/t in the gravity feed to an average of 2 600g/t in the concentrator feed to the in-line reactor. The recovery of gold in the in-line reactor is in excess of 98.5%.This paper discusses the background to the project, the laboratory testwork prior to the equipment selection, the operational results of the system, as well as the benefits of the future application of high mass yield centrifugal concentrators in base metals, sulphides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONBesides picking nuggets off the ground or out of riverbeds, gravity concentration is arguably one of the oldest methods of recovering gold. In circa 6000BC people discovered that gold can be found behind the rocks and in depressions of creek beds. By placing rocks in a stretch of channel with the proper slope the first sluice is built, probably around 4,000 BC, and this method is still practiced today."

Jan 1, 2009

Collins Radio Company, through this contract with the Bureau of Mines, has conducted a System Study of Coal Mine Communi¬cations. The program was a three phase program to establish a data base, perform communication system analysis and optimi¬zation, and prepare equipment specifications to be included in this final report. At the start of establishing a data base both a knowledge of mine communication and coal mines in general was obtained. Communication system requirements and constraints were determined along with a survey of current and potential mine communication equipment. An investigation was completed concerning theoretical LF and VLF propagation characteristics, and UHF propagation tests were conducted in a working coal mine. Different mines were contacted and on-site surveys completed with respect to coal mine communication requirements.

Jan 1, 1973

By J. C. Borland, J. H. Rogerson

Jan 1, 1963

By J. Hollow, D. Walsh

The Fort Knox Mine is located in Alaska’s interior, where the average ambient air temperatures range from -24oC in January to 16oC in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and a conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leach, carbon adsorption and cyanide destruction kinetics. Additionally, an energy balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post project plant performance that validates the model and shows the mine produced an additional 596 kg (19,155 ounces) of gold, while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Cristian Rodriguez, Tom BoBo, Maria Rocha, John Kemeny

Blast fragmentation depends on many factors. First of all, it depends on the specific blast design, which includes the amount and type of explosive, the blasting pattern, the timing and sequencing, and other parameters. Secondly, it depends on the properties of the rock mass, including the uniaxial compressive strength (UCS), the rock mass elastic modulus (E), the rock discontinuity characteristics (as reflected in the GSI or RMR), and the rock density. Several fragmentation models have been proposed to predict blast fragmentation based on the blast design and the properties of the rock. These models include the Kuz-Ram model and variations of this model, as well as recent models by Kim and Kemeny (2011) and others. Fragmentation models are validated and calibrated by comparing the predicted fragmentation with actual post-blast fragmentation from image processing monitoring systems.

Jan 1, 2014

By R. L. Grayson, J. R. Warneke

The mining industry has searched for a message that will resonate with the public while focusing on the industry’s positive contributions to society. Thus far environmental groups remain unconvinced, and the public is still largely uninformed. In the authors’ opinion, a number of recent events and experiences have converged to help shape a more effective public communication on mining’s important role. This paper presents a fresh and cogent perspective on coal’s role in sustaining society by anchoring the message in a transparent material flow analysis that links coal’s impacts across a broad range of social and environmental aspects.

Jan 1, 2006

By Scott D. Thomson

The client for this project specializes in the use of state-of-the-art technology to fabricate and assemble composites and metal-bonded structures for commercial and military aircraft programs. One of the key components for this operation at the client's plant is a highly precise computer-numerical-controlled router known as the Shoda Machine. This machine tool was installed at the plant in July 1998 for the manufacture and inspection of aircraft parts, and it is extremely sensitive to deflections. To monitor the occurrence of deflections, an internal laser system continuously checks the machine calibration. Deflections in excess of 5/1000-inch in the foundation on which the machine rests require costly periodic re-leveling and recalibration of this tool. Therefore, a significant problem arose when measured deflections during machine operation were as large as 20/1000-inch. In addition, the foundation was cracked in at least three places as a result of elastic foundation movement caused by dynamic loading as well as shrinkage and loss of base support. Deciding on a remediation procedure to alleviate or eliminate these problems involved the following important considerations: (1) achieving the client's need for reducing deflections to less than 5/1000-inch, (2) minimizing the repair cost as much as possible, and (3) reducing the time required for implementation of the foundation remediation solution. After evaluating the advantages and disadvantages of several alternatives, jet grouting was selected as the most suitable solution. The jet grouting program provided columnar elements of soilcrete to remediate the Shoda Machine foundation.

Jan 1, 2003

By Ma. X.

Passive seismic imaging is applied in underground mining to analyze the stress redistribution after the occurrence of a major seismic event. The velocity model is established to be utilized in velocity inversion. By comparing the images from velocity tomography on two different time scales, the average velocity of a mining area decreases significantly after the major event. It is highly likely that the stored energy level drops due to the occurrence of a major event. Also, total energy stored in micro-seismic events for each day is summed up and the energy change trend is plotted to illustrate the correlation of energy with a major event.

Feb 27, 2013

By É Lèbre, G Corder

The circular economy concept, as defined by the Ellen MacArthur Foundation (2015) and quoted by the recent International Council on Mining and Metals (ICMM) Guide to Responsible Sourcing, calls for shifting industrial systems from a linear take-make-waste model to a circular model (ICMM, 2015). In this model products are designed to optimise product and material recovery and reuse, and by-products of one system are used as inputs into other product systems. While the mining industry to date has made a limited contribution to the circular economy, the current market conditions, which are prompting calls for greater innovation, make the timing right for the industry to boost its contribution by utilising and generating value from mining waste, or making it available as a feedstock from which other industries can harness value.The first part of this extended abstract discusses the way the circular economy concept can be adapted to metal mining activities, contributing to a more sustainable resource extraction at the mine site level. The second part of this extended abstract presents a circular economy based framework revolving around non-renewable resources conservation. The third and final part examines the application of the framework to the Mount Morgan mine in Central Queensland.CITATION:Lèbre, É and Corder, G, 2016. Utilising mineralised mining waste – contributions to the circular economy, in Proceedings Life-of-Mine 2016 Conference, pp 132–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947