Search Documents

By D. W. Holliday

The major deposits of anhydrite and secondary gypsum in Jamaica occur discontinuously at a single horizon within the Lower Eocene succession of southeast Jamaica. They are not intruded from other horizons of different age, as has previously been supposed. The gypsum and anhydrite occur in a regressive sequence at the junction between marine (Richmond Formation, Halberstadt Volcanics, Halberstadt Limestone) and overlying non-marine (Wagwater Formation) sediments. They are thought to have been formed in an arid supratidal (sabkha) environment. A variety of 'nodular' structures occurs in the gypsum and anhydrite which can be related to early diagenetic processes and compaction effects. All gradations exist between single isolated anhydrite nodules and structureless anhydrite due to closer packing and coalescence of nodules. The structures and textures in the anhydrite are thought to be consistent with penecontemporaneous formation from gypsum crystals rarely more than 2 cm in diameter. Single anhydrite nodules are not usually larger than 2 cm; nodules of greater size are compound, due to the coalescence of several smaller nodules. Some large compound nodules may have developed from single sand crystals or rosettes. Compaction of anhydrite appears to have been largely mechanical, but some rocks have an aligned fabric, suggesting later flowage

Dec 1, 1971

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006

By William F. Boericke

KIRKLAND LAKE and Porcupine in 1931 accounted for more than $41,625,000 of Ontario's total gold production of $43,117,688. For the first time, the younger camp surpassed the older in gold output, producing $21,734,000 against $19,891,000 for Porcupine. Present output of both camps is increasing, and should pass the record figures of 1931 before the year is out. In May of this year, Porcupine mines milled 285,759 tons, with a bullion value of $1,810,009; the corresponding figures for Kirkland mines are 149,188 tons and $2,104,757. A much higher average value per ton for Kirkland ore, $14.10 against $6.33 average for Porcupine accounts for the difference. The two fields are about 100 miles apart by rail, and there are important differences in the character of the ores, which accounts largely for the difference in milling costs and in final tailing values, despite excellent metallurgical work in both the fields.

Jan 1, 1932

By Ray Brainard

Charleston Water System?s Daniel Island Extension Tunnel, initially thought to be the simplest of the four replacement tunnels to design and build, became the most challenging after the discovery of an unexpected 30-ft thick lens of sand in the normally consistent Cooper Marl while sinking a shaft on Daniel Island. This paper will explore the challenges involved with determining the extent of the unforeseen lens of sand, the accelerated boring program, and the redesign of the vertical alignment?keeping the alignment between the sand layer and the bottom of the Cooper River. It will describe how the challenges were overcome, and how the Owner, Engineer, and Contractor were able to team together to achieve the desired results.

By PáDeáBosscher, A Bruwier, M Weidenbach, C Philippe, T Ly, A Van Den Bosch

In the mining business the cost of grinding media represents up to 40 per cent of the total milling cost and therefore grinding media optimisation has a direct impact on the concentratorsÆ bottom line. In the process of optimising grinding media alloys, Magotteaux developed its own methodology which consists of a series of analyses, tests, calculations and evaluations and assist the concentrator in optimising their processes.This paper presents the Prominent Hill case study where this methodology has been applied on both the secondary ball mill and regrind IsaMill«.The analysis of the wear conditions in the secondary ball mill allows Magotteaux to select a series of grinding media alloys to be tested to reduce grinding media consumption. By marking these different grinding media types with a unique drilling pattern, one can quantify the relative wear performance and cost effectiveness of each grinding media type within the same milling environment. After selecting the most economical grinding media composition a full scale industrial trial, involving topping up the selected grinding media is carried out and the media wear performance closely monitored and analysed.For stirred grinding mills, suppliers propose different grinding media, mainly ceramic beads, with specific properties and cost. Therefore the concentratorsÆ choice is a compromise between grinding efficiency, wear resistance and cost. The selection of the correct grinding media for stirred milling and the assessment procedure will be presented in this paper. The test results of the new stirred grinding media type in the regrind IsaMill« at Prominent Hill are presented and analysed.CITATION:Weidenbach, M, Van Den Bosch, A, Bruwier, A, Ly, T, De Bosscher, P and Philippe, C, 2012. Forging ahead - A collaboration between the OZ Minerals Prominent Hill Concentrator and Magotteaux to improve plant performance, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 105-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M. Dworzanowski

The beneficiation of fine iron ore will increase in importance in the future because most new iron ore resources will be in the form of lower grade ore deposits that will require liberation of iron ore minerals at finer sizes. Generally this fine iron ore will be beneficiated to produce a pelletizing concentrate with very strict chemical and physical specifications. In addition, because of the increasing demand for iron ore there are now more opportunities to produce by-product iron ore from mining operations producing other commodities. In the past the associated iron ore minerals would report to final tailings but now there is potential value to be realised from by-product revenue. These by-product iron ore opportunities are almost all centred on producing pelletizing concentrate. Currently pelletizing concentrates are produced mainly by various combinations of flotation and magnetic separation. The selection of the beneficiation route will depend on ore mineralogy and considerations around plant capacity and final concentrate quality. The main economic iron minerals are magnetic, haematite being paramagnetic and magnetite being ferromagnetic. This, therefore, means that magnetic separation can be applied, in principle, to all fine iron-ore beneficiation plants. While flotation has a considerable capacity advantage over magnetic separation, the real advantage of magnetic separation over flotation in fine iron-ore beneficiation is that treatment of -10 µm iron ore is possible-in flotation, the feed is deslimed at 10 µm and the -10 µm stream is considered to be final tailings, even though there is often a significant amount of contained iron ore. This paper describes a study around the recovery of fine magnetite in the form of a pelletizing concentrate. The study is based on an evaluation of an iron ore by-product opportunity from an iron oxide copper-gold (IOCG) deposit. Experiments were conducted to quantify the differences in magnetic separation performance with decrease in particle size treated. A mineralogical evaluation of all the test work products was undertaken to facilitate the interpretation of the test work results. These results were then used to propose an economically viable flowsheet for maximizing fine magnetite recovery using magnetic separation.

Jan 1, 2012

By Kelly Sands

"Mitigation may be considered a hurdle when it comes to environmental permitting. For complex projects with site specific mitigation plans, the time to devise those plans and get them approved can be a long and costly endeavor. However, mitigation options are expanding and the mitigation banking industry has grown tremendously over the last two decades, helping projects move forward with less debate. Mining companies are recognizing the value that mitigation banks provide in helping to shore up project timelines and costs. Where possible, companies are taking advantage of the opportunities to buy credits from thirdparty providers offering mitigation bank credits. In some instances, mining companies are taking matters into their own hands by establishing mitigation banks to realize their own mitigation freedom. That can have its advantages and disadvantages, as discussed below. All in all, the expansion of mitigation options has streamlined the permitting process, introduced flexibility, improved project permitting timelines and loosened the permitting girdle.Compensatory mitigationCompensatory mitigation involves actions taken to offset unavoidable adverse impacts to wetlands, streams and other aquatic resources and authorized by Clean Water Act section 404 permits and other permits. As such, compensatory mitigation is a critical tool in helping the federal government meet the longstanding national goal of ‘‘no net loss’’ of Waters of the U.S., both in acreage and function.Section 314 of the National Defense Authorization Act for Fiscal Year 2004 required the Secretary of the Army, acting through the Chief of Engineers, to issue regulations “establishing performance standards and criteria for the use, consistent with Section 404 of the Clean Water Act, of on-site, offsite, and in-lieu fee mitigation and mitigation banking.” The provision also required that those regulations ‘‘maximize available credits and opportunities for mitigation, provide flexibility for regional variations in wetland conditions, functions and values, and apply equivalent standards and criteria to each type of compensatory mitigation’’ (73 FR 19595). The result was the Final Rule on Compensatory Mitigation for Losses of Aquatic Resources issued in 2008 (33 CFR Parts 325 and 332).”"

Jan 6, 2017

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By Gordon R. Sima

This contract is concerned with feasibility studies, design and fabrication of a prototype hand-held test instrument and a machine-mounted test Instrument for measurement of electrical shock hazards of mining machines. This report presents the proposed and detailed design of the hand-held test instrument and the machine-mounted test instrument. Theory of operation of each instrument is discussed and includes the operating parameters.

Jan 1, 1976

By P. Hickey, J. Spenceley, T. J. DeMull

Development of the Batu Hijau Project was successfully completed in the fourth quarter of 1999 with the final handover and start-up of ore processing facilities. The development project had started more than three years earlier, in August 1996, when the Owner, PT. Newmont Nusa Tenggara (PTNNT), awarded an EPC contract to Fluor Daniel (FD) for design and construction of the project including: copper concentrator, port, power plant, town site, and infrastructure. PTNNT managed the development of the mine and procurement of mine equipment with its own forces. Bringing the Batu Hijau copper deposit into production was the largest mining project ever undertaken. Development of Batu Hijau was a complex project involving the work of tens of thousands of people in all parts of the world to complete engineering, manufacture and deliver equipment, supply materials, and build the plant. The ore deposit is located on the tropical island of Sumbawa in a remote and undeveloped section of Indonesia. The location and environment presented challenges for all phases and aspects of the project. To meet the challenges, the project team combined good planning and teamwork to best utilize the resources available. This approach assured continuity of personnel through construction to operations and minimized cost, resulting in completion of the project ahead of schedule and under budget.

Jan 1, 2001

By Lawrence Nordell

A Conjugate Anvil-Hammer Mill (CAHM) has the potential to replace conventional crushers and SAG mills, with their respective conveyors and stockpiles, in a SABC circuit. It may improve comminution circuit efficiency by 100%. CAHM compresses rock in a more efficient way, similar to 19th century stamp mills, which follows the fundamental research of Schönert (1990 & 1996). CAHM efficiency is being proven through the use of ROCKY (2011) Discrete Element Method (DEM). ROCKY features allow it to simulate realistic comminution. CAHM is customizable with many geometries that are rock-property specific. ROCKY?s wear modeling compliments the structural integrity of the design.

Jan 1, 2012

By M. O. Serbousek

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed an eight-piece precast reinforced concrete drift set for a small opening. Twenty-two sets of three different member sizes were tested to destruction under two loading conditions. A discussion of the test results and typical failure patterns is presented.

Jan 1, 1969

By V. G. Grechanyuk

The paper presents the mechanical properties of Cu-Mo composite materials depending on the molybdenum content. The influence of structural defects on the mechanical-physical properties of the condensates at stretching testing as well as of the lamellar grain dimensions upon the mechanical properties of Cu-Mo composite materials is also presented.

Jan 1, 2008

From time to time lead, which is normally considered to be a soft ductile metal, fails by cracking. The cracks which form appear to be of two distinct types-(a) those which follow a zig-zag course around the boundaries of crystals and (b) those which follow a more direct path, frequently two systems of cracks appearing at right angles.The former appear definitely to be associated primarily with the properties of the crystal boundaries, whilst the latter appear rather to be determined by the system of stresses applied. In both cases the lead appears to be a brittle rather than a ductile metal, for the failure occurs without the large amount of deformation usually associated with the tensile breaking of lead. The latter is, however, a function of time and when lead is deformed by long applications of stress, the metal appears to- be less ductile than when the stress is applied suddenly. Thus, if a given test piece of commercial lead is broken by a stress of 1100 lb. per sq. in. in several hours, it may extend 40 to 50%before failing, whereas when broken by a stress of 500 lb. per sq. in. acting for 12 months or more it willshow an extension of only 15 to 25 %. With lower stresses still, failure would take much longer and undoubtedly lower extensions would be obtained.As the stress is lowered it is found that the marked local contraction characteristic of ductile metals becomes less noticeable, and failure, instead of being by extension of *Lecture delivered to the First 'Ordinary Meeting of the Australasian Institute of Mining and Metallurgy, 21st August, 1935.

Jan 1, 1935

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

In July 1982 the Committee on Underground Coal Mine Safety completed its study of safety in U.S. underground coal mines; the results of the study were published in the National Research Council report entitled Toward Safer Underground Coal Mines. One of the findings of this study was: THERE IS A STRONG CORRELATION BETWEEN MINE SIZE AND FATAL INJURIES. THE FATALITY RATE IN MINES WITH 50 OR FEWER EMPLOYEES IS NEARLY THREE TIMES THAT OF LARGE MINES (WITH OVER 250 EMPLOYEES), AND ABOUT TWICE THAT OF INTERMEDIATE-SIZED MINES (WITH 51-250 EMPLOYEES). Although the Committee explored possible reasons for the higher fatality rate in the smaller mines, it was not able to explain this phenomenon fully. Therefore the Bureau of mines requested that the Committee undertake a supplementary study of fatalities in small underground coal mines. The Committee met in the fall of 1982, discussed the problem, developed an approach to it, approved a program of statistical analyses, and authorized a panel of four committee members to explore the problem in greater depth. The panel, in turn, reviewed the results of the statistical analyses and met with the president of the National Independent Coal Operators Association and with several owners of small underground coal mines for a detailed discussion of the unique problems of small mines. Panel members examined 66 individual fatality reports prepared by Mine Safety and Health Administration (MSHA) inspectors who investigated fatal accidents that occurred in small underground coal mines in 1979 and 1980. This report is the result of those studies, analyses, and deliberations. The first draft was prepared by the panel, but the report has been reviewed and approved by the entire Committee.

Jan 1, 2011

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By M I. Roberts

Corporate and workplace culture, as many owners, directors, executives and managers know, is by far the most powerful determinant of productivity. It’s much more significant than buildings and equipment. Yet although no one today would build a building or machine without a plan, few leaders have a plan for building and sustaining a safer and more productive culture.Using practical ways, culture can be planned and shaped as desired. Success requires implementing a project plan for changing the systems that drive behaviours that in turn shape attitudes. The combination of behaviour and attitude together with leadership largely shape culture.To improve performance, leaders need to:1. improve the organisational systems that drive behaviour2. action a project plan for improving specific performance metrics 3. demonstrate leadership that is conscious, disciplined, committed and passionate for purposeful use of human energy.This paper explains all three factors in practical ways with operational and corporate examples. It details understanding and applying the power of fundamental statistical analysis tools to recalibrate, focus and drive proactive leadership that takes responsibility for process improvement, supporting people and ensuring accountability.Experience and practical understanding of human and organisational behaviour confirm that the Measurement ? Analysis ? Reporting system combined with conscious leadership is by far the most powerful driver of behaviour. This wisdom produces profound changes in leadership style and behaviour. It develops outstanding leadership to create and sustain a safe and highly productive culture reliably producing consistently high quality products. It is the key to developing accountability, employee retention and a sustained competitive advantage.CITATION:Roberts, M I, 2016. Building safe, productive cultures and leadership, in Proceedings International Mine Management Conference, pp 163-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016