Search Documents

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By Donald H. McLaughlin

PRICES paid for goods and services in paper currencies are undoubtedly determined by many interrelated factors, but among them none is more specific in pushing prices toward higher and higher levels than the vast increase in debts and monetary obligations of our own and practically all major governments. There is nothing unorthodox in the situation in which the gold miners find themselves today. With wages and the prices of all materials required in the production of gold at the high levels characteristic of a period of prosperity, phony or otherwise, and with shortages of both men and machinery to contend with as well, the spread between the returns in paper dollars that must be accepted for gold in the United States and the cost of producing it is rather painfully small for most producers. Technical

Jan 1, 1948

By R. Drummond

The fourth Teetered Bed Separator (TBS) has just been installed in Australia, and trials have been run in many sites. There is a growing recognition of the potential advantages of using TBS technology to treat coal in the ?3+0.25 mm size range, at cut points below 1.60. From these activities, there has been a substantial growth in knowledge with respect to application engineering and operational functions. The paper briefly describes the installations, including flowsheets, and so provides a background to the potential deployment of TBS technology. There are a large number of potential applications for TBS technology, including treatment of fine ROM coal in new plants, or in upgrade situations for re-processing of spiral product, or scavenging coal from coarse tailings. As well, cost effective capacity upgrades are possible by using TBS units for treating the sands size fraction. Issues arising from Australian TBS installations and application engineering are also discussed.

Jan 1, 2002

Mineragraphy is a coined term to signify the field of microscopic investigation of ore minerals. The term is not euphonius and is sometimes regarded as superfluous because the subject is no more than an enlargement of the scope of petrology. In the past the practical field of petrology has been largely limited by the instruments which were designed for the study of rocks and' the microscopical properties of the transparent minerals. The addition of mineragraphy has been brought about by the use of the reflecting microscope and a totally different technique.The use of the petrological microscope, as it has been employed in the training oi geologists and mining engineers for nearly half a century, has been justified many times, not only in its application to general geological problems, but also in the more restricted field of the exploration and examination of ore deposits. It provides information of the gangue minerals and rocks associated with an ore body which is of great value in some mining fields. In cases where ore deposits occur selectively in certain favourable types of rock, the recognition and delineation of these rock types is a useful guide in prospecting. The Boulder Belt at Kalgoorlie forms one of the most striking examples in Australia where important significance is attached to different rock types, and the petrological microscope is essential to their elucidation.

Jan 1, 1932

By G. P. Halliwell, C. R. Austin

The investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at t,he Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word ''Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 per cent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy," or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limitJ' has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend test developed by Howard Scott.' In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1932

By C. Richard Tinsley

INTRODUCTION The economic analysis (Chapter 3), the engineering studies (Chapter 10), the credit structure (and the consequential funding sources) - Chapter 11, and the overall feasibility structure for any venture are all directed to determining one major decision element: How much and how certain is the reward for taking these risks? Risk assessment is a surprisingly weak area of analysis and is usually addressed in a checklist fashion. It is much preferable to deal within a risk system so that the inevitable tradeoffs among risks are correctly made. DEFINITION The first step toward risk definition must be to ascertain all of the risks to which a project or a company is exposed; otherwise one will remain ignorant of the possibility of a financially crippling loss until it occurs. (Carter and Crockford, 1974). However, simply stating what "risk" is can lead to debate. For example, risk could be (adapted from Vaughan, 1982): -the chance of a loss - uncertainty of loss -possibility of loss - uncertainty -dispersion of actual from expected results - probability of an outcome different from the one expected - possibility of an occurrence of an undesirable contingency -a condition in which a possibility of a loss exists. For the minerals industry financier, the last definition is probably the most appropriate. However, from a mineral company's point of view the definition might well include the possibility of not achieving the expected financial return. RISK CLASSIFICATION Risk identification will be readily agreed as the all-important first step. There are five major "branches" of risk classification. These are: -Statistical -Modellers -Checklist -Project Financing -Insurance The Statistical set discovered probability theory and any risk discussion soon deteriorates into a mathematical jungle (Megill, 1977; Hartman, 1976; Reutlinger, 1970; and Pouliquen, 1970).Their use of terminology tells its own story: coin toss (binomial distribution), gamblers' ruin, delphi (oracle) techniques, monte-carlo simulations, random walks, etcetera. These techniques inadequately represent the judgements necessary in an increasingly complicated and interrelated world. The risk Modellers have turned to the computer to handle these inter-relationships but soon find barriers because of "simultaneity". Certainly the computer has its uses to conduct various analyses (marketed as "sensitivity" analyses) but very often one finds that this involves changing one or two variables at a time, all other things being equal. Unfortunately, in a modern and complex world all other things do not remain equal. The statisticians will, no doubt, jump to their own defence by citing this

Jan 1, 1985

Five watersheds, ranging in size from 29 to 49 acres, were selected in East-Central Ohio to investigate the hydrologic and water quality conditions occurring before, during, and after surface mining. Four of the watersheds will undergo surface mining, involving either the Number 6, 9, 11, or 8 coal seams, and one watershed having an outcrop of the Number 6 coal will be operated as a control watershed. To determine the premining hydrologic and water quality conditions (Phase 1), physical information was obtained for each watershed and instrumentation was installed for obtaining hydrologic data and water quality samples. In addition to topographic maps, soils and vegetation maps were prepared. Stratigraphic columns were developed from geologic cores; networks of observation wells and of soil moisture access tubes were installed; and weather stations were established to measure temperature, humidity, wind and solar radiation, and to collect precipi¬tation samples. Field data were collected over a 10-month period for one watershed and for about 8 months on another watershed before surface mining began. The other watersheds continued in the premining data phase. These data were for precipitation, temperature, relative humidity, wind speed, solar radiation, snow and frozen soil, soil moisture, infiltration (rainfall simulator), spring discharge, runoff from watersheds, and ground-water levels. Also, samples of runoff and ground water were obtained for chemical analyses and additional samples of runoff were acquired for suspended sediment load determinations. Over the study period, precipitation was not very representative of the long term averages, but data are available from the control watershed for a representative 7 year period which should prove invaluable in modeling the hydrology of the project watersheds for the premined conditions. Spring discharges (before mining) from the upper aquifer of two of the watersheds averaged only 508 and 652 gallons daily. The proportion of precipitation occurring as surface runoff from the large watersheds ranged from 8 to 36 percent and the peak discharges from 5.86 to 81.95 cfs. Base-flow and runoff water samples from four of the watersheds (unmined conditions) were collected and analyzed quantitatively for 39 water quality parameters. Monthly precipitation samples sediment fractions of the base flow and runoff were analyzed for 22 and 17 parameters, respectively. The average concentrations of the water quality parameters for the watersheds (unmined), except for suspended solids, were as low or lower than the EPA recommended maximum allowable concentrations in drinking water. Several parameters in precipitation equaled or exceeded the levels of corresponding parameters in runoff water. The average concentration of suspended solids in storm runoff ranged from 118 to 1110 mg/l, and for base flow the range was from 44 to 247 mg/l; the higher concentrations were associated with the watersheds exhibiting the greatest disturbance. Iron ranged from an average of less than 3 µg/1 to 228 µg/1. Manganese ranged from less than 41 µg/1 to 334 µg/I. Ground-water systems (unmined condition) are described for the five project watersheds. Each watershed was found to have two major perched aquifers within the top 250 feet. Generally, these perched aquifers involve local flow systems, though flow across watershed boundaries in some areas. Recharge is mostly from local precipitation and discharge is mostly as spring flow, base flow, evapotranspiration, and leakage through the underlying confining bed. Shallow ground water was commonly of the calcium bicarbonate type. Although dissolved-solids concentration was generally 200 to 600 mg/1, brackish or salty ground water was present in several areas. A composite hydrologic model for the project watersheds will consist of separate ground-water, unsaturated flow, overland flow, and evapotranspiration component models. The ground-water model (a modified quasi-three--dimensional U. S. Geological Survey model) operates on a grid network and the newly formulated unsaturated flow model was divided into overlying prismatic elements for numerical solutions. The unsaturated flow model includes provision for incorporating the evapotranspiration model. An available distributed kinemetic overland flow model was utilized. An analyses was made of one of the costs of reclaiming coal mines; the legal and administrative costs of complying with legislation. Such costs borne by coal companies under the Ohio law are thought to be a surrogate of these costs under the new Federal law. Regression analyses were used to relate the legal and administrative costs to acres in the permit and the tonnage of coal produced.

Jan 1, 1978

By William G. Schultz

Sylvite of Canada, a wholly owned subsidiary of Hudson Bay Mining and Smelting Co., operates an 8000 TPD potash mine and refinery located nine miles North East of Rocanville, Saskatchewan. Prior to Hudson Bay's entry in 1968 into potash mining and refining, it was one of the more traditional and conservative Canadian Mining Companies whose principal business had been for many years a successful copper-zinc mining and smelting operation located at Flin Flon, Manitoba. The potash reserves being mined by Sylvite were acquired through the acquisition of Francana Oil and Gas. This acquisition was at the time when several major potash mines were being developed or had recently been brought into production in the Province. These mines are owned by either very substantial Canadian Mining Companies or Multi-National Mining Companies with considerable potash mining experience. At that time, it became very apparent because of the new mines coming into production, potash mining and refining would quickly become a very competitive industry. Because of long term considerations, Hudson Bay decided to proceed with the development of its potash reserves, recognizing the Mine and Refinery would have to be the most advanced available in order to successfully operate. This report deals with the mining operation at Sylvite and the degree of success Sylvite has achieved.

Jan 1, 1972

By Walter Nuñez

La finalización de la estimación de reservas de un modelo de mina cuestiona la asertividad del modelo de Mina para la planeación minera. En ese sentido, el presente texto señala la Reconciliación como la comparación real histórica de tonelaje, leyes y contenido fino estimado, entre el modelo de mina y planta concentradora. La reconciliación permite conocer y ajustar mediante el uso de factores, la planeación mensual y anual de los siguientes años de la operación minera, y así cumplir con los compromisos mensuales asumidos de envío de contenido fino desde mina. Así también se muestra el proceso que sigue la explotación minera a tajo abierto en Toquepala, las variables que influyen en la variación de la reconciliación y algunas pautas a considerar para minimizar estos errores de reconciliación entre mina y concentradora.

Sep 19, 2006

By William D. Macdonald

The Upper Devonian Kettle Point black shale of southern Ontario is poorly exposed. Structural maps pre-pared from the data of numerous wells show that the upper surface of the formation has low regular relief, and that the lower surface reflects domes in the Middle Devonian and also local subsidence of the Devonian rocks due to solution of salt in the Silurian Salina Formation. The appearance of minor amounts. of marcasite, pyrite, and calcite, m that order, as interpreted from the evidence of concretions from the type locality at Kettle Point is thought to have been influenced by a rise m the pH within anaerobic sediments preceding compaction.

Jan 1, 1960

By Robert F. Shurtz

This paper suggests that pre-occupation with the random process model notised by geostatisticians may result in neglect of more promising techniques, especially since the random process model does not appear to be essential to current geostatistical procedures. This point of view is emphasized pictorially. To emphasize the potential of new techniques a simple application of the conventional Brownian function is described. The probabilities estimated in this truly random way are different from those estimated by Kriging

Jan 1, 1980

By J. Mikhael Erekson, Connie Campbell Brashear, Brent Meins

Christmas morning 2020, an IED in an RV was detonated along an evacuated section of downtown Nashville, Tennessee. The blast damaged over 40 buildings, including AT&T’s Main Central Office and caused internet and cell outages across 1,200 zip codes for three days including the airport and EMS services. Published investigations by the ATF and FBI were inconclusive in determining the explosive composition and size. Video captured a large fireball that may indicate a fuel-air-mixture explosion which would create lower peak pressures than high explosives, but longer pressure duration and significant impulsive loading. Blast pressures were amplified by reflections in the urban environment bordered by the 8-story AT&T building and a row of multi-story historic buildings. Some structures had little damage as they were shielded from the blast pressure by closer buildings, and seemingly far-field structures contained damage from the pressure wave after multiple reflections and propagation through porous parking garages. Damage to the reinforced concrete frame AT&T building included snapped masonry ties, cracking and spall to the closest column, and vertical displacement of the elevator, even with the brakes applied. The historic structures directly across the street from the blast partially collapsed. Initial damage included complete failures of unreinforced masonry façades, broken timber beams, and uplifted roofs. Secondary, progressive collapse took place over months as the brick walls and weakened historic mortar could not resist typical wind and environment loads. One of the close historic structures was renovated in the 1990’s and structural retrofits to comply with building codes were required. The addition of steel columns and façade tie-ins improved survivability and it remained standing with a high percentage of the front brick intact. Generally, the observed blast damage was related to a structural component’s mass and flexibility. Internal timber framing was unscathed, but many steel studs required replacement. Glazing damage was observed several blocks away and many roof membranes were punctured by falling debris. Secondary damage from broken sprinkler lines and loss of environmental control often led to more costly repairs than the initial blast pressure damage. The proliferation of bomb-making knowledge leads to hundreds of bombings each year in the US. Building risk considerations should include explosive threats along with other hazards. ASCE structural standards and design manuals have been published to address these risks and may be useful guides for building construction.

Feb 6, 2023

By M. C. Makepeace

"It is the objective of designed experiments to obtain more information for less material and process cost than can be obtained by traditional experimentation. In this paper, the fundamental concepts on which the statistical design of experiments is based are briefly re-viewed according to the following outline: The Experiment The Design The Analysis Two simple 2"" factorial experiments are presented as examples."

Jan 1, 1967

By D. A. Larson

The Bureau of Mines conducted basic experiments to study the process of crack propagation with a wedge indenter. The work was conducted under plane stress conditions in a hard, brittle limestone. The purpose of these experiments was to first gain an understanding of the basic crack propagation process under a sharp indenter, and second, to determine how the crack propagation process could be used to improve mechanical fragmentation systems. Three methods of rock fracture with the wedge indenter were investigated in this program. These were the confined indentation tests, the unconfined splitting tests, and the edge chipping tests. The confined indention tests represent worst case conditions for crack growth and formed the lower bound on fracture efficiency. The unconfined splitting tests represented best case conditions and fixed the upper bound of fracture efficiency. The edge chipping tests represented an idealized fragmentation process based exclusively upon the highly efficient fracture propagation process. Edge chipping achieved a specific energy of 25 in lb f/in3 compared to conventional drag cutters, which required a specific energy of at least 2,385 in·lb f/in3? Thus edge chipping is up to 100 times more efficient than conventional drag cutting. Because of these promising results, more work is planned with the fracture propagation process in three dimensions.

Jan 1, 1987

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By S. James Campbell

Ladies and Gentlemen: Never in the history of our mining industry has the emphasis on public relations been accelerated as much as it has in the last few years. Knowing of your keen interest in this subject I consider it a great privilege that your program committee has asked me here to discuss the crushed stone segment of our industry approach to this important part of our daily business lives. As you are aware, crushed stone operations are present in almost every segment of the country wherever aggregates for construction projects are required. The tonnage of crushed stone produced is second only to sand and gravel - another source of aggregates - and this together with sand and gravel amounts to over half of the tonnage of all mined products in the United States. What is unique about this industry that will be of interest to all of you in analyzing how they have approached Public Relations? The fact that it is so wide-spread is of course obvious, but perhaps a more significant nature of this segment of the mining industry that has brought it more in the limelight of public interest and on a larger scale is the location of a large part of the quarries quite close into the urban area and population centers where you have the greatest demand for aggregate products.

Jan 1, 1969

By Robert W. Waytulonis

Mining regulations pertaining to the use of diesel engines were solicited from foreign countries with mining operations by the Bureau of Mines. Responses were received from 27 countries; the information received and U.S. regulations were reviewed, and those parts pertaining to the use of diesel engines in underground mining were synopsized according to the following subject categories: types of engines permitted, testing and certification procedures, fuel quality specifications, emission control requirements, procedures and frequency of testing exhaust gases, mine air quality and quantity (ventilation) requirements, procedures for testing mine air quality and quantity, and noise standards. All categories except the types of engines permitted and testing and certification procedures are summarized in tables. Contacts are provided for each country to facilitate inquiries concerning regulation revisions or interpretation.

Jan 1, 1987

By C. A. Heiland

THIS year's review of geophysical activities has a somewhat different complexion than usual. With the ending of the war, the time seems opportune to supplement the customary report on operations and discoveries in oil and mine exploration by a review out-lining the contributions of geophysicists to the. war effort. To give as much space as possible to the latter, presented as Part 2, some of the usual review features have been omitted from the statistical section, given as Part 1 immediately following.

Jan 1, 1946

By Percy W. Bidwell

THE statisticians had defeated Germany months before she invaded Poland. With batteries of adding machines they had proved that she was suffering from serious deficiencies in critical food- stuffs and in practically all of the raw materials necessary for the conduct of modern warfare. Their calculations showed that with respect to fats, oils, wool, cotton, hides, petroleum, iron, copper and other metals, the Reich was bound to be at a great disadvantage vis-a-vis the French and British as long as the latter could keep open the lines of sea communication. The conclusion seemed obvious-"Germany can't win." The more cautious of the commentators introduced qualifications as to the length of the war and the tightness of the British and French blockade. They also made a third qualification as to the character of the struggle- whether it was to be a war of attrition or a war of movement. But since the invasion of Norway in April, there is no longer any doubt on this score. It is a war of movement-a war in which fuel, lubricants, and metals are being consumed on a scale never before seen.

Jan 1, 1940

By P. M. Ambrose, A. C. Fieldner

This , the 11th annual report of research and technologic work conducted by the Bureau of Mines on coal and coal products , is issued following the closing of the Bureau's war work on fuels and contains references to most of the published articles containing results of war investigations . The few remaining papers will be discussed in next year's report . The trend in coal research in the Bureau of Mines was discussed in Mechaniza- tion . This publication , covering the period from the close of armed con- flict to resumption of normal coal -research activities , includes a section never previously presented . There is included for the first time a discussion of the Bureau's activities in the Liquid Fuels and Lubricants and the Solid Fuels Subcommittees of the Technical Industrial Intelligence Committee . This report does not replace the more comprehensive ones prepared by individual authors and listed as footnote references in this publication . purpose is to bring to the reader a résume of the work for the fiscal year ended June 30 , 1946. The material presented herein is based largely upon publications , but the results of some research and testing, which would not otherwise be published in the near future, are presented in detail .

Jul 1, 1947