Search Documents

By E O. Foster

When roasting started at Giant Yellowknife Mines in 1949, it became apparent that, to prevent air and water pollution in the surrounding district, it would be necessary to collect the arsenic that was contained in the exit gases of the roaster. The arsenic collection problem was finally solved by the installation of both electrostatic and baghouse collectors. It was realized that a considerable quantity of gold-bearing dust was leaving the roaster with the exit gases. When the collection problem was solved, it was possible to measure this loss. The loss proved to be considerable and it became evident that a substantial quantity of gold could be recovered. Research programs on dust treatment began in 1958, and by May, 1960, the treatment process which is currently being followed was started in the plant. At present, the two electrostatic preci11itators, Operated at temperatures above 600°F, collect the gold-bearing dust.

Jan 1, 1963

By Jeffrey S. Walker

Abandoned underground mine openings are susceptible to collapse because of the mining methods used, the character of the overburden, and the typically large, wide entries with minimal roof support. The final effect of the collapse of the underground workings is surface subsidence. To reduce the probability of subsidence, methods to backfill the mine void with various types of materials have been developed. This U.S. Bureau of Mines report describes the available technologies for subsidence abatement and discusses their operation and application. The basis of these abatement methods is the replacement of the mined material with mine waste. Backfilling of mine voids is the most common method of stabilization used to abate subsidence and protect surface structures. Hydraulic flushing and grouting, using remote methods from single or multiple boreholes, are the most often-used methods for the placement of backfill material. Other subsidence abatement techniques are available and may be more appropriate under different conditions. These other techniques include pneumatic stowing, either by in-mine or remote methods, and various point support methods that do not completely fill the mine void and are used for the protection of small areas of the land surface and surface structures.

Jan 1, 1993

By Graham W. Marks

In broadening the utility of spectrochemical methods 9f analysis of ore samples 3,4/ a procedure employ in the total energy method, has been adapted to determination of silver in ores. Silver is the first element in group I of the periodic table to be studied in the Bureau of Mines program. Two silver lines in the spectrum, Ag X\ 3280.683 and 3382.89lR were used in the study, and the problems that had to be overcome were: (1) Influence of extraneous elements on line intensities, (2) preparation of standard curves, and (3) improvement in equipment and technique to increase accuracy. Sodium, potassium, sulfur, selenium, iron, cobalt, and nickel yielded low intensities and hence low results, particularly on the samples high in silver, but addition of 60 percent or more of lime counteracted these effects. One calibration curve must be used for samples low in silver and other for those high in silver. The chocks with fire assaying were close enough for preliminary or exploratory investigations, and the method is much more rapid.

Jan 1, 1948

By William I. Weisman

The annual consumption of fluorspar in the United States, in the last 10 years has doubled. In 1971, when 1,344,742 tons were consumed, almost 45 percent of this amount was used in the production of steel and nearly 50 percent was consumed in the manufacture of hydrofluoric acid. Of the hydrofluoric acid produced, about one-third was used in the manufacture of aluminum electrolytes for production of primary aluminum metal and the balance was consumed in the manufacture of a variety of fluorocarbons and other chemicals. A small amount of fluorspar, constituting less than five percent of total consumption, was used in the foundry industry, and in the manufacture of glass, enamel, cement and other products. It is apparent that a continuing supply of fluorspar will be required to meet the demands for these vital metals and chemicals in our expanding industrial society. Domestic fluorspar production meets only approximately 20 percent of our needs. Hence, it is essential that the United States maintain a healthy domestic fluorspar industry in order to have adequate domestic reserves available at times of emergency and to protect this country from becoming solely dependent on foreign sources for this strategic commodity.

Jan 1, 1973

By Cyro Takano

A tecnologia de autorredução apresenta um grande potencial por apresentar características de alta velocidade de redução e de eficiência energética, resultando em economia de energia e em alta produtividade na produção de metal primário. Têmse dois processos consolidados de aglomeração. A utilização de cimento como aglomerante, com cura a frio que formam hidratos que conferem resistência, apresenta problema principal de sofrer degradação às temperaturas na faixa de 800 a 1000 °C, devido à decomposição dos hidratos. O outro processo é o de utilização das propriedades do carvão de alta fluidez e tratá-lo termicamente para que sirva de redutor e aglomerante. Este processo não é o de cura a frio, porém diminui consideravelmente a quantidade de escória em comparação com a utilização de cimento. O objetivo deste trabalho é o de analisar, na literatura técnica, os aglomerantes alternativos e iniciar os ensaios para verificar os comportamentos de resistência mecânica, principalmente a quente. Em função dos resultados a etapa seguinte será a de projetar um processo que seja compatível com resistência mecânica a quente. A análise resultou em sugestões para os ensaios. Os resultados preliminares, com utilização de bentonita e ácido bórico estão indicando resistência a quente das pelotas melhores que as obtidas com a utilização de cimento.

Aug 17, 2017

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By Djalma Souza, Jean Igor Margem, Sergio N. Monteiro, Frederico M. Margem

Synthetic fibers have been used for many years to attend the demands required by the technologica lfields. However, the use of them has been questioned due to the impact on the environment. In this way, the natural fibers have received extensive attention, in particular hybrid fabrics of natural fibers to reinforce environmentally friendly polymer matrix composites. Thus, the present work has the objective of evaluating and comparing the mechanical properties of composites formed by hybrid fabric with 70% Malva—30% Jute in epoxy polymer matrix. The tests carried out are the Charpy and Izod Impact Tests, with specimens of 10, 20 and 30% in volume of hybrid fabric environmentally friendly into polymer matrix composites at room temperature. The 30% samples had the best results, functioning as an efficient reinforcement.

Mar 1, 2018

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By Robert G. Lundguist

REAM is a unique and promising method of rock breaking using high energy, inert projectiles to impart mechanical energy to the rock. This paper describes a demonstration of the application of this new technology to two specific problems in open pit mining: secondary breakage and the scaling of loose material from pit walls. Under previous government contracts, Physics International Company developed the projectile impact method for a large variety of commercial and military rock excavation tasks. A 4 meter (13 foot) diameter by 16.8 meters (55 foot) long tunnel was driven at the Hope Valley Mine in the Sierra Nevada mountains of California in 1972 and 1973. An average of 1100 kg (1 ¼ tons) of a 172 MN/m2 (25,000-psi) granodiorite formation was broken by each of 590 shots used to drive the tunnel.l Based on these results it is estimated that REAM can drive over 60 meters (200 feet) of tunnel per day at about 88 percent of the cost of drilling and blasting. In addition, repeated axial impact by high energy projectiles was used to drill a 0.4 meter (16 inch) diameter horizontal hole in the same granodiorite formation. Each shot advanced the hole an average of 0.2 meter (8 inches).

Jan 1, 1976

By Dorsey A. Lyon

"The ceramic industry of the United States has a total yearly manufactured product of nearly half a billion dollars, despite large foreign importation.After careful investigation of the industry by the Bureau of Mines, it is the belief of those in charge that the usefulness of the industry can be greatly enlarged and the importations greatly lessened through the development of processes that will lead to a greater and better development of the ceramic resources of the United States. This will result in a greater industry with more men employed than ever before, and perhaps a world's supremacy in ceramic trade matters.Investigations in behalf of the ceramic industry are being made at the Bureau of Mines experiment ceramic station at Columbus, Ohio, under the supervision of R. T. Stall, superintendent, who reports a number of instances of practical, beneficial cooperation between the industry and the station during the last fiscal year.Graphite to Crucibles:Prior to 1914, practically all graphite crucibles manufactured in the United States were made from Ceylon graphite bonded with German Klingenberg clay. It was the general belief among graphite crucible manufacturers and users that good crucibles could not be made from American bond clays and graphites.Graphite crucibles were essential for melting certain alloys and special steels urgently needed for the manufacture of war materials. The demand for such metals was so great that it created an unprecedented demand for graphite crucibles.After the European war began no Klingenberg clay could be shipped out of Germany. However, it was fortunate for the cyucibly makers that they had large stocks of Klingenberg clay on hand. When the stock of Klingenberg clay became exhausted, it was necessary for the credible makers to turn their attention to American clays. There were no data or other information available to guide the crucible makers in the selection of good bond clays for their crucibles. It was necessary for them to select their clays more or less by ""guess"", which resulted in the period of service or life of graphite crucibles being shortened 15 to as much as 60 per cent."

Feb 1, 1921

The application of new and currently practised mining techniques in new areas and at greater depths necessitates considerable and immediate research effort. This effort is aimed at identifying the factors which make a particular method suitable and economically viable in a given geological, structural and operational environment. These factors, together with greatly enhanced knowledge of a deposit at the exploration and planning stage, allow selection of the most appropriate and efficient mining method in a new area such that coal resource recovery is maximised in a cost effective manner. Current research and future requirements for research into mining methods and associated equipment and mine services are reviewed.

Jan 1, 1981

By M. Z. Emad, A. Khan, N. Abbas, K. G. Li

Probability-based empirical methods were employed as an alternative approach to predicting uncertainties associated with rock mass properties. The focus was on developing probabilistic spreadsheets to forecast rock mass classification indexes. Histograms were constructed to describe the best distribution in predicting rock mass properties. The developed models also offer utility in predicting the impact of discontinuities within the rock mass on rock strength and rock mass classification systems. Statistical analyses identified volumetric joint count, joint spacing, joint frequency, and rock strength as the most influential parameters. Moreover, the statistical analysis revealed varying degrees of correlation among different rock mass properties. While some properties demonstrated significant correlations suitable for modelling, others did not align well with any correlation model. The results highlight the need for a comprehensive approach to rock mass characterization, considering multiple factors beyond volumetric joint count. Geological complexities, including tectonic activity and weathering processes, may obscure direct correlations. These results emphasize the importance of empirical modelling and detailed site investigations for accurate assessment of rock mass quality and stability in the Himalaya.

Jun 10, 2024

By W. W. Agey

This report summarizes results of bench-scale metallurgical studies by the Federal Bureau of Mines on three composite samples representative of the low-grade manganese ores purchased by the General Services Administration (GSA) and stockpiled at Deming, N. Mex., and Wenden, Ariz. Bench-scale flotation tests at the Salt Lake City Metallurgy Research Center showed that all three composites could be beneficiated by flotation to recover 88 to 90 percent of the manganese in concentrates that assayed from 38.5 to 39.0 percent Mn, 10 to 12 percent insoluble, 5 percent CaO, 3 to 5 percent Fe, and 1.3 to 1.7 percent combined Pb plus Zn plus Cu, Sintering studies indicated that specification-grade material could be made from these concentrates by sintering above 1,000° C, and adding either sodium or calcium chloride to the charge to insure removal of enough lead and zinc to meet the specifications.

Jan 1, 1962

By A M. Nyembwe, A M. Garbers-Craig, R Cromarty

With the depletion of high-grade lump iron ore, concentrates have been identified as an alternative material for sinter making. Adding concentrates to the sinter mixture reduces sinter bed porosity and gas flow through the sinter bed. This will result in lower sinter strand productivity. A potential solution to this problem is to add concentrate in the form of micropellets. This study investigates the effect of concentrate and micropellet additions on the permeability of the sinter mixture. Permeability was measured on sinter mixtures containing ten to 40 per cent concentrates and micropellets at various moisture contents. The effect of concentrate and micropellet addition on the permeability–moisture relationship was examined. The results confirmed that the addition of concentrates into the sinter mix decreases the maximum permeability of the sinter bed. The incorporation of micropellets into the sinter mix reduced the permeability less than concentrate addition. The study also showed that the maximum permeability of sinter mixes containing concentrate is reached at the same moisture content as the sinter mixture without concentrate addition. For sinter mixes containing micropellets, additional water must be added to obtain maximum permeability. Parameters including the granule size, void fraction and angle of repose were also investigated to evaluate their effects on the sinter bed permeability.CITATION:Nyembwe, A M, Cromarty, R and Garbers-Craig, A M, 2015. Effect of concentrate and micropellet addition on iron ore sinter bed permeability, in Proceedings Iron Ore 2015, pp 69–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By R Jacobs, J Yeates

"The Stockman base metals project is situated in State Forest in the alpine area of East Gippsland, Victoria, adjacent to a National Park and within the headwaters of a major Ramsar-listed wetland catchment and the Murray-Darling River system. Site topography is steep, and elevated (650 m – 1200 m above sea level), and subject to circa 1 m annual rainfall, with occasional winter snowfall. The project consists of two volcanogenic massive sulfide (VMS) deposits to be mined by underground methods and treated in a 1.0 Mt/a central concentrator to produce copper and zinc concentrates for export over a ten year operational life. New resource projects are rare in Victoria. Recognising the sensitive setting, planning for the Stockman Project, which is now in the advanced permitting stage, has focused on balancing economic, environmental and social outcomes to ensure social licence to operate is secured and can be maintained. This has involved close attention to triple bottom line (TBL) risks and outcomes. Stockman has successfully gained State and Federal approvals via the Environmental Effects Statement process. The process of obtaining these approvals has required close attention to effective stakeholder involvement, and management of a lengthy and difficult approvals process, which is still to be finally concluded. This paper is a case study of the process of that permitting and the issues encountered to date. Key learnings from the experience have included: successful approvals require close attention to much more than just the project and its technical aspects and physical setting – effective stakeholder involvement and endorsement is critical the differing consultation requirements for local, regional and government stakeholders, to design and plan implementation of a project to meet TBL objectives, and to gain social licence to operate within the Victorian approvals process, the need for an effective lead government agency with policy authority dealing with material policy change requiring post-closure financial sureties estimating realistic permitting time and cost during the project evaluation phase. CITATION: Jacobs, R and Yeates, J, 2016. Stockman base metals project – sustainability, social licence to operate and permitting lessons learnt, in Proceedings Project Evaluation 2016, pp 98–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Mario J. Arenas Figueroa

El presente trabajo señala la formación geológica del yacimiento minero de Julcani, el fracturamiento de esta estructura, como los principales controles de su mineralización. En este sentido, la estructura del yacimiento es epigenético con vetas del tipo de relleno de fracturas en volcánicos Terciarios, caracterizadas por una mineralización en rosario y con valores de plata altamente erráticos. De otro lado, el fracturamiento es complejo puesto que este atraviesa tres periodos, las cuales coinciden con el rumbo de las vetas principales. Los principales controles de mineralización son el tipo de roca encajonante, los diques, intersecciones, etc, señalándose sus características para una exploración sistemática de nuevas vetas y bolsonadas.

Nov 20, 1967

By R. W. Bruce

The normal practice for processing complex sulphide ore has been to grind with steel balls and/or rods in steel mills before flotation. Little thought had been given to the effect of grinding media on flotation selectivity of copper-lead -zinc ore until 1960 when Rey and Formanek(1) published their experiments on sphalerite floatability after grinding in a porcelain mill with ceramic pebbles. The studies by Rey and Formanek had a pronounced effect on the milling of copper-lead-zinc ores in Canada and possibly throughout the world at a time when autogenous grinding was creating a great deal of interest. The impression was created, and possibly still exists with some mill men, that grinding an ore in the absence of steel will result in a loss of selectivity between copper, lead and zinc minerals. This is in spite of the fact Rey and Formanek's experiments showed that the "naturall floatability" of sphalerite was not apparent after grinding in a porcelain pebble mill in an alkaline pulp.

Jan 1, 1976

By M. Sinirkaya

The dissolution process of phosphate rock from the Semikan area (Mardin-Mazidagi, Turkey) using dilute phosphoric acid has been investigated. The work involved studying the effect of important variables, such as reaction time, stirring speed, particle size fraction, phosphoric acid concentration and temperature. Van der Sluis et al.?s model was used to determine the rate of the partial dissolution of phosphate ore. Mass-transfer coefficients (kL) varied between 2.8 and 28.5.10-3 m.s-1. The activation energy of the process varied between 16 and 20 kJ.mol-1. It has been found that the dissolution process is controlled by calcium ion diffusion, rather than by chemical reaction.

Jan 1, 2010

By R. Mensah-Biney

The loading characteristics of gold-tetrabromide species onto activated carbon have been evaluated using a completely mixed batch reactor system. The overall loading of gold onto carbon was rapid for the first hour but continued slowly without cessation as a result of reduction of gold. Conventional equilibrium considerations were therefore not applicable. Although loading continued slowly after several days, abnormally high loading capacity values of 10-12 meq/g carbon (650-800 kgAu/tonne) could be attained within 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of [AuBr4l-onto the carbon surface where reduction to metallic gold took place. Elution of gold from the loaded carbon was feasible provided the carbon had not been loaded to too high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon is discussed.

Jan 1, 1992

By H. S. Castro

The by-product molybdenite technology in Chile is reviewed. Flowsheets, reagents and some operation features for the actual six Chilean moly plants(Chuquicamata, El Teniente, El Salvador, Andina, Las Tortolas and Pelambres), are presented. The chemical and physicochemical factors involved in the depression of copper and iron sulfides during the selective flotation of molybdenite, with sodium sulfide, sodium sulfhydrate, anamol-D and LR-744, are discussed. Advances in technology to solve problems of excess of lime (precipitation with sulfuric acid); excess of residual flotation reagents (activated carbon and kerosene); and optimization of depressant consumption (Eh control, nitrogen and low-oxygen air), are discussed.

Jan 1, 1998