Search Documents

By G. R. Hodgson, M. P. Lebourg

The introduction in the field of a new type well completion called for the setting of tubing open-ended in the well before perforating the casing. This paper describes a new perforating tool of the shaped charge expendable type, small enough to pass through tubing and powerful enough to perforate the casing. The perforations are produced at an angle and are large enough for optimum production. Performance of this tool in targets and under various well conditions is described. Very often no lifting equipment will be available at the well. In some cases, pressure will exist in the well at the time of the perforating operation (workover wells or multiple trip perforation) ; therefore, new equipment and new technique for the perforating operation were devised. This paper describes this equipment and technique, particularly casing collar recording, sheave support, and cable pull-down device. this last item being necessary for wells under pressure. Results obtained with this tool in the field are given. INTRODUCTION One of the key requirements for the introduction in the field of a new method of permanent well completion was the development of a new perforating method involving the use of a perforating gun small enough to go through tubing and with enough penetrating power to perforate the casing satisfactorily. The equipment described in this paper was basically designed to go through open-ended two-in. tubing and to perforate 5 1/2 in. casing. The equipment is illustrated in accompanying figures. NEW COMPLETION METHOD With the new permanent type well completion, the production string of casing is run and cemented through the potential producing zone. Open-ended tubing is -then run into the well and used to replace the drilling fluid with oil or water. The amount of the oil or water "cushion" can be varied according to the expected bottom hole pressure. Thus, if desired, the hydrostatic head can be greater, equal to, or less than the expected pressure within the zone to be perforated. Mud having been displaced, the tubing is -then positioned so that the end is above the zone to be perforated. The Christmas tree and flow lines are installed and tested. The drilling rig can now be removed from the well since it is not necessary for the perforating operation, thus resulting in a saving in rig tme. The perforating equipment is then moved to the well and the gun lowered through the tubing. After the gun passes out of the open end of the tubing, the depth measurements are correlated with casing collars and the gun placed opposite the zone to be perforated. Upon firing, the gun body is shattered and falls to the bottom of the well. Since the lubricator has been closed before firing, it is possible to withdraw the casing collar locator and head and then open the well immediately to the tanks. DESCRIPTION OF GUN An investigation of two basic types of Perforators, namely a bullet perforator and a shaped charge gun, was undertaken towards the development of a gun to meet the aforementioned requirements. Preliminary tests on various bullet perforator designs within the diameter limitations did not give results encouraging enough to warrant further study. Somewhat better results were obtained by using conventional shaped charges; but, as in the case of the bullet types, the necessarily small overall diameter proved to be a severe limitation and resulted in insufficient penetration. A shaped charge employing a new design was developed which gave excellent penetration. These shaped charges were designed to produce a large hole directed upward at a 45" angle. In order to obtain the maximum space possible for these charges, it was decided to use an expendable carrier made of drillable material, usually aluminum, which would shatter at the time of firing, leaving only harmless fragments at the bottom of the hole. The fixed spacing is five shots per ft. wit11

Jan 1, 1952

By Claudia Castillo, Katja Freitag, Jan Cilliers, Diana Drinkwater, Robert Seitz

The talent gap in mining is not a new challenge. Mining companies continue to seek innovative ways to attract, develop and retain talent, and younger workers are looking for opportunities to develop their professional careers. Training provides a key value proposition for both employees and employers as it helps build a talent pipeline while offering opportunities for learning and growth and value creation. In 2020, Metcelerate launched its 20-month program for early career mineral processing engineers. The program helps develop critical technical skills in the workplace and is a tool to identify motivated engineers and change culture within teams. Learners cap their skills development by executing a technical investigation. This generates immediate value—a win-win outcome for learner and company.

Feb 1, 2025

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By Bill A. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six-head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin.The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill.The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator's station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt, and mesh sump.The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in tum lowers the miners' roof exposure per cut. This design reduces the operator's exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore, the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely."

Jan 1, 2016

By Mariana Boger Netto

O fósforo é um elemento crítico para a qualidade dos aços, tornando a redução dos teores desse elemento uma exigência para a indústria siderúrgica. Uma forma de se medir a eficiência da desfosforação é através do coeficiente de partição do fósforo (Lp=%P(escória)/%P(aço)). O objetivo principal deste trabalho é avaliar escórias de um forno elétrico a arco através da comparação entre o Lp real com o Lp calculado por simulação termodinâmica, avaliando, também, o comportamento da partição de fósforo com relação à composição química. A partir de dados de composição química de amostras de escória e aço de uma usina siderúrgica, foram feitas simulações termodinâmicas utilizando o software FactSage. Com base nesses resultados, concluiu-se que o cálculo computacional através do software descreve bem o comportamento termodinâmico, mas tende a superestimar o Lp, provavelmente por questões cinéticas e/ou de transferência de massa e calor.

Aug 17, 2017

By Richard F. Link, George S. Koch

Advantages and disadvantages of deflecting (wedging) diamond-drill holes to obtain sampling data are compared with the alternative of drilling additional holes. The discussion is based on a statistical analysis of a large set of deflection data from exploratory boreholes in South African gold mines. Representative cost comparisons show the conditions under which deflections are likely to be desirable.

Jan 1, 1969

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By Gunjan R. Bhattarai, K. Bhattarai

Applications of machine learning and robotics in the tunneling industry are still nascent. Research and development are ongoing in TBM guidance; prediction of TBM cutter wear and tunneling induced ground deformations; and robotic arms for segment installation, inspection, cleaning, and maintenance of TBM cutting tools. This paper presents a case study of geological profile reconstruction using multimodal machine learning. The results from this study can aid the development and application of multimodal AI technologies to generate data reports and geological profiles in real time, taking voice recordings, photos, or videos obtained directly from the field as inputs.

Jun 23, 2024

By D. G. Tisdale, W. Curlook, J. M. Toguri

"In this study, the vapour phase reduction of titanium tetrachloride conforms to the traditional Kroll chemistry, but employs argon as an inert carrier gas and requires a higher reaction temperature of 1150°C to 1250°C. A vapour phase reaction is advantageous because titanium is the only condensed phase present, and the metal can be collected free of magnesium or magnesium chloride, in marked contrast to the titanium sponge produced by the conventional Kroll process. The yield of metallic titanium from the reaction was determined as magnesium additions ranged from 36% to 168% of the stoichiometric requirement. Yields of over 99% were obtained when an excess of magnesium was present. Although the collection efficiency was low, metallic titanium was collected at the reaction site, where all other species were present as vapours. Magnesium and chlorine concentrations in the collected titanium were less than 0.3%.IntroductionA proposed method (Curlook, 1987) for titanium production has been investigated as an alternative to the conventional Kroll process (Kroll, 1940). The advantages of the new process include a simplified means of recovering the product metal, and a potential for lower overall energy consumption and greater product purity. A higher reaction temperature for the reduction of titanium tetrachloride results in a vapour phase reaction, rather than the conventional liquid phase reaction. This is the major conceptual difference between the proposed and the established (Kroll) processes.This study focussed on optimization of the process chemistry and briefly examined the issue of product deposition and collection. The reduction of titanium tetrachloride with magnesium, to produce metallic titanium and gaseous magnesium chloride:"

Jan 1, 1997

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

This Bureau of Mines report is a compilation of information on computer models of mineral commodity markets in the Federal Government, The directory was compiled by the Analytic System Working Group of the Interagency Minerals Information Coordinating Committee to support the formulation of policies related to nonfuel minerals.

Jan 1, 1984

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

By H. Verakis, M. A. Hockenberry, A. C. Smith, J. H. Rowland III

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on their effectiveness in extinguishing conveyor belt fires. The four different types of suppression system were water sprinkler, deluge-type water spray and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 1.8-m- (72-in.)-wide fire-resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 152 - 168 m (500–550 ft) per minute (mpm) and 411 - 457 mpm (1,350 - 1,500 fpm). Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to and extinguish any smoldering belting was greater than the current MSHA regulations required. MSHA regulations only require 10 minutes of water supply for a suppression system. In the test setup, neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 152 mpm (500 fpm) air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test setup, arrangement of the fire suppression systems and conclusions regarding the effect of air velocity on fire suppression system design and performance.

Jan 1, 2010

Cooperation will be the keynote of the meeting of the Institute that will be held in New York on February 17 to 20. Arrangements are being made for two joint sessions with the Canadian Mining Institute, on the same day, which therefore will be known as Canadian Mining Institute Day. On the afternoon of Wednesday, February 19, there will be a joint session with the American Institute of Electrical Engineers. Besides, we will receive six or eight papers through the National Research Council, four of which will be presented at the National Research Council Session. In March, at the next meeting, of the Canadian Mining Institute, there will be an American Institute of Mining Engineers Day. The plan is to have the same subjects discussed at both meetings, but by different speakers. One speaker on each subject will represent the Canadian Mining Institute, and one speaker the American Institute of Mining Engineers. The Canadians and the Americans who will speak in Canada are expected to attend the discussion in New York. In addition the discussion at the New York meeting will be sent to Canada in printed form, so that the Canadian discussion will be a continuation of the former. At the joint session with the American Institute of Electrical Engineers, there will -be presented six very important papers on the subject of Electric Welding, one by the Chairman of the Electric Welding Research Committee of the National Research Council, another by the Chairman of the Metallurgical Sub-committee of that same Committee, and a third by Comfort A. Adams, President of the American Institute of Electrical Engineers and Chairman of the Welding Committee of the Emergency Fleet Corporation. We will receive six or eight papers through the National Research Council. These papers are results of recent investigations and represent the last word in their respective subjects. The excursion on Thursday, February 20, will be to Newark Bay to visit the Federal Shipyard where the first, electric-welded ship is being built. Philip W. Henry is chairman of the excursion committee of arrangements.

Jan 1, 1919

By F. T. Davis

Many contributors have added to the fund of knowledge in the basic sciences related to mineral dressing during the past year. During 1964, the French edition of the Proceedings of the VIth International Mineral Processing Congress together with discussions was printed. Also, complete Preprints of papers delivered at the VIIth IMPC were published in September1. Over a third of the papers presented at VIIth IMPC dealt with fundamentals. COMMINUTION It has been postulated by Ponceleta that flaws need not exist before a stress is applied but rather the flaws are created at the tip of a propagating crack at a stress well below the theoretical breaking stress.

Jan 2, 1965

By J. Erik Loehr, Minh Uong, Andrew Z. Boeckmann, Sarah G. Myers

"The University of Missouri performed a lateral load test program involving 32 drilled shaft load tests for the Missouri Department of Transportation (MoDOT). Tests were performed at two MoDOT geotechnical research sites, and all shafts were founded in shale. Shafts were instrumented to measure the displacement of the shaft head, and the structural response of each shaft was interpreted from strain gage data and from ShapeAccelArray (SAA) data. The SAA is a chain of rigid segments with sensors that use MEMS (microelectromechanical systems) technology to measure the tilt of each segment/joint. The measuring principle of the SAA is therefore similar to that of an inclinometer. The SAA device was placed in a casing installed in the center of each test shaft to provide a continuous record of deflection along the length of the shaft throughout each test.Bending moment profiles were calculated from strain gage data and from SAA data. Interpretation of bending moments from measurements of strain (via strain gages) and displacement (via SAA) is a nontrivial exercise, primarily because the bending stiffness, EI, is nonlinear and greatly influenced by concrete cracking, which is difficult to predict. The procedure used for this work predicted values of bending stiffness along the length of the shaft as a function of the bending curvature, which was interpreted from the SAA data. Values for bending stiffness as a function of curvature were computed using Ensoft LPile v2012. Bending moment profiles from SAA data were typically similar to those from strain gage data. The SAA bending moment profiles were often “noisier” than the strain gage bending moment profiles, but the SAA bending moment profiles had more data points since the SAA chain was continuous from the top to the bottom of each shaft."

Jan 1, 2017

By Paul Toor

The operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles ? in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012