Search Documents

By C. A. Holley

The generation of coal fines is a growing problem which has serious environmental and resource recovery Impact. Several methods of agglomeration are studied including the production of briquettes for the consumer market. Simplified process flow diagrams, "order of magnitude" plant capital cost and operating costs are presented.

Jan 1, 1986

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019

By David Leidel

A revolution in hydrocarbon well completions within the last thirty years has enabled drillers to tap the resources of known gas plays in an economically viable manner and deliver to market natural gas supplies for industrial, transportation and domestic use without the importation of liquefied natural gas from verseas. An added benefit has been the convenient location of one of these gas plays, the Marcellus Shale, in the Northeastern states strategically close to a major natural gas market, namely the cities and towns of the New England and Mid-Atlantic states. As a sidelight, the development of the tight gas reservoirs and their subsequent production has created thousands of jobs in an otherwise lackluster economy.

Jan 1, 2014

By John F. Burst

For several generations now, the high alumina clayey sediments of Southeastern Alabama and Southwestern Georgia have supplied those regions with steady, mineral-based income although the impact of that income has been relatively minor until recently. Since World War II, mining activity has increased algebraically with over half of the total ore value in the Alabama area having been recovered since that time. The Georgia area production increases are even more dramatic. The trends are continuing and the next decade should see ore winning figures which will dwarf all previous production. It's time for the mining engineers to take note of this development as the mining methods, similar to the production, have developed rapidly and now offer challenges for the most competent professional. The development of mining techniques has followed a classic pattern. Beginning almost a hundred years or so ago, with the loading of weather-resistant surface boulders into mule-drawn wagons, mining methods have progressed to discovery of limited surface exposures in outcrop and eventually to stripping and development of non-obvious, subsurface deposits. Little by little, the overburden thickness of new pits has increased until, at present, pits with 100' -125' of overburden are being actively worked. Ground water problems in the Eufaula District are particularly challenging. At A. P. Green's J. W. Baker Pit, #l, in Barbour Co., Alabama, it is necessary to continually pump groundwater at the rate of about 400 gallons per minute from wells on the periphery of this large pit in order to keep the water table low enough to allow mining of the ore body.

Jan 1, 1972

IN THE past, we have, perhaps, been somewhat careless in our furnace practice, in the use of high-grade material, lowering the production costs through demanding high-grade ores, increasing the size of units, and eliminating heat losses by collecting and returning unused heat to our furnaces. Further economies would seem to be possible through keeping out of the furnace those materials that appear to serve no useful purpose and carry with them heat that should be used in reduction operations. In the manufacture of pig iron, about three tons of inert nitrogen pass through the furnace for each ton of iron produced. This nitrogen serves no useful purpose in the chemical actions involved, but when discharged into the atmosphere it carries away a considerable quantity of heat. Can not this loss be eliminated, at least in part, through the use of more oxygen in the blast? Many metallurgical chemists, during the past 20 years, have stated that they thought it can and have urged that the plan be tried. Others have expressed doubt, not being able to visualize how more oxygen could be used in present practice; they have regarded it as impracticable, without trying to conceive of an entirely new practice based on a new reagent. That more experimental work has not been done is due to the fact that no cheap oxygen has been available, but the committee believes that there is strong reason to expect that, should a demand exist, 99 per cent. oxygen may be made at a cost not to exceed $3 per ton. The theoretical studies of the committee have indicated such marked economy by using oxygenated air in various operations that its members strongly recommend experimental work to verify the anticipated economies. The committee has developed plans for experimentally determining the effects of oxygen-enriched air on the operation of an iron, blast furnace. A furnace with a height of 30 ft. has been built and it is recommended that the plans be put in, effect as the first step in the research.

Jan 11, 1924

By W. R. McDonald

The U.S. Department of the Interior, Bureau of Mines, conducted field tests on acidic copper tailing as part of its program to devise, improve, and demonstrate technology for stabilizing mining and mineral processing wastes. Results will be presented from successful 1/8-acre and 1-1/2-acre demonstration revegetation plots established in 1973 and 1974 on an abandoned copper tailing pond located on public land adjacent to Holden Village, Wash. The tailing was neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Plant growth covering 60 percent of the surface was achieved on both test plots. Regar brome, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. In neutralizing the tailing, the target pH of 6.8 was not achieved; however, good plant growth occurred in areas where the pH ranged from 2.9 to 5.8.

Jan 1, 1979

By Yoon-Bong Hahn

A mathematical model has been developed to analyze and predict the reduction process of iron ore particles in a two-stage fluidized bed system. This model includes the effect of particle degradation to elucidate its effect on reduction of iron oxides. Although the particle degradation is dependent on kind of iron ores, it was found that eighty to ninety percent of overall degradation is occurred in the prereduction stage mainly due to thermal stress and volume expansion. The degradation of particles in the?final stage is not much, but is mainly due to interparticle collision and abrasion. It was also found that to obtain a target reduction degree, it is of great importance to control the bed temperature and the residence time of paarticles in R1 rather than in R2. Optimum range of residence time was 15-20 minutes in the prereduction stage; 30-35 minutes in the final reduction stage.

Jan 1, 1996

By Ricardo Miranda Alé

Aços resistentes ao serviço ácido (sour service), com requisitos adicionais de alta resistência mecânica e tenacidade, têm sido especificados para aplicação em gasodutos do Pólo Pré-sal da Bacia de Santos. O desenvolvimento de aços que atendam a estes severos requisitos, visando à fabricação de tubos de elevada espessura, constitui um enorme desafio para o fabricante do aço. No presente trabalho, é apresentado o desenvolvimento do aço API 5L-X65 Sour Service para esse tipo de aplicação, onde são descritas as principais ações realizadas no processo de produção que permitiram o sucesso no desenvolvimento do produto, confirmado pelas excelentes propriedades obtidas nas chapas e nos tubos.

Aug 8, 2018

By G. G. Manekar

MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprise, under the Ministry of Steel, Government of India, produces about 1.1 million tonnes (T) of manganese ore annually from three opencast and seven underground mines. The underground operations are mining using an overhand cut and fill method. The orebody is too narrow for the use of larger equipment and the poor to fair rock mass quality limits the size of stable excavations. Prior to the 1990s underground support consisted primarily of timber square sets in tandem with timber chocks and props. As mine production requirements increased throughout the 1990s led to larger opening sizes and more modern support practices. Research was conducted on ground support design based on rock classification and empirical techniques for designing ground support. Based on the findings and field trials, the Company adopted full column cement grouted cable bolts for back support. Instrumented field trials, using extensometers and load cells on the cable support confirmed the support effectiveness. Stope design was based on two and three dimensional stress modeling which resulted in a significant increase in stope dimensions. The rock mechanics studies for safe stope design were carried out using numerical modeling tool in two and three dimensions for the analysis of stresses. Based on the findings, the safe stope geometry with new stoping parameters was introduced. The earlier stope length of 30 mtrs were changed to 60 mtrs with in situ rib pillar at the cross cuts and in situ post pillars to be left-out in the stope. This leads the formation of of panel comprising of three stopes, for production, supporting and filling. For mechanical handling of ROM in stopes Side Discharge Loaders (SDL) were introduced. The above changes have improved the face productivity from 2?3.5 T with manual operation and 9 T with SDL. The above rapid mining operations has improved the stope productivity but reduced the stope life from 6 to 3 years. For the improvement of the stope availability, further studies were conducted by numerical modeling of stress analysis. The related studies confirmed that with the existing supporting system and proper instrumentation, level interval could be increased up to 45 mtrs from the existing 30 mtrs at deeper levels. At present below 12th Level interval is 45 m at Balaghat Mine. For future mechanization program for introduction of Single Boomers, LPDT, Cutting Machines etc for the development headings rock mechanics studies are underway. The paper provides details of rock mechanics studies that were carried out to study efficacy of the cable bolt support, safe stoping parameters and increased level interval for the improvements in safety, production and productivity at Balaghat Mine.

Aug 1, 2013

By Frank J. Wiebelt

The Veta Chica and Cerro Colorado chromite deposits of the McGuffy Creek area, Siskiyou County, Calif. were selected as worthy of investigation by the Bureau of Mines in accordance with the Strategic Minerals Act of 1939. These were two of many chromite deposits examined by engineers of the Bureau of Mines during their extensive wartime mineral examination and exploration campaign. Exploration by the Bureau of Mines consisted of 2,234 feet of diamond drilling, surface trenching, and sampling during the months of May and June 1942.

Jan 1, 1949

By Hans Lundberg

N OT so long ago, the discovery of an orebody took place only by accident. At the present time mineral deposits, even though concealed, may be revealed by their physical or geophysical characteristics, considered in connection with geological studies. Geophysical methods are based on sound, scientific principles and in no sense partake of the mysteries of "divining-rod " methods. Geophysical methods are divided into two main groups: Group I: Methods where fields of force surrounding mineral deposits are investigated (magnetic, gravitometric, electric) ; Group I1 : Methods where fields of force are applied (produced) and anomalies caused in these fields by mineral deposits are recorded (electric, seismic). By methods belonging to Group I, the investigation of the fields of force may be brought to an astonishing degree of accuracy by means of highly sensitive and delicate apparatus (torsion and magnetic balances) ; at least, in simple cases these methods have proved to be of great value.

Jan 1, 1925

By Farouk T. Awadalla

The presence of humic species in spent Bayer liquor causes many processing problems in the production of aluminum hydroxide. Ozonation of spent Bayer liquor was found to be an effective process to destroy the colored humic species. The kinetics of the decolorization in spent Bayer liquor was found to be slower than in the alkaline humic acid solution containing no alumina. However, the reaction kinetics ware enhanced by heating the solution during ozonation above room temperature. Copper ions which are used as catalyst to enhance the ozonation reaction were found to be ineffective due to the presence of large quantities of aluminum hydroxide in the liquor. Ozonation was a more favorable process than membrane separation as it achieved about 92% separation of color and produced lower amounts of organic material. The treated spent Bayer liquor can be recycled to the upstream process without causing any difficulties and the purity of aluminum hydroxide product would also be improved. A comparison of preliminary cost data indicated that ozonation compares very favorably with membrane separation in this application. Key words: ozonation, Bayer liquor, aluminum hydroxide, humic species, copper ions, membrane separation, purity and economic.

Jan 1, 1994

By P. Morissette

Passive monitoring of support performance during rockbursts was conducted at three deep underground mines. A comprehensive database was constructed of 172 seismic events and the associated damage to support systems at 266 mine locations from January 2000 to September 2012. The majority of pertinent information was obtained through seismic system records and on-site field assessments. This work assesses the quality of collected information and evaluates the dynamic-load demand on support systems in seismically active mines.

Aug 1, 2013

By Xiao-hui Fan, Li-shun Yuan, Xu-ling Chen, Wei Lv, Min Gan, Yi Wang

"As the amount of ferrous scrap increases every year, it becomes more and more urgent to deal with this iron-bearing resource properly. This paper puts forward a method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing), and these cold-bonded pellets can be used as coolant in a converter. The influence on the pellets qualities by using different kinds of chloride as rust agents is studied, and results show that the strength of cold-bonded pellets increases significantly by using a combination of the three kinds of chloride -NaCl,MgClz,FeCh, their best dosages are 1.2%, 0.2%, 0.1% respectively. Other iron-bearing materials also have an effect upon the pellets strength, by adding 5% iron powder and maintaining for 48h, the compressive strength of the clumps surpass 2500N/A, dropping strength surpass 4 times/ A, and 10% iron slag or 20% steel slag can replace 5% iron powder while obtaining the comparative quality. The influence of different ratios of three ferrous scrap (converter mud, iron scale and dust) is further studied, and results show that when the ratio is 30% : 30% : 40%, the pellet strength reaches the maximum. After maintaining for 24~48h, the clumps can meet the mechanical as well as the physical-chemical requirements as BOF steelmaking refrigerant.IntroductionGreat amounts of converter mud, dust and iron scale are produced in steel production process. These materials are of great values, and their accumulation not only leads to environmental pollution, but also wastes the precious resources, which restricts the sustainable development of the steel industry [1,2] The main approach at present to dealing with the ferrous scrap is to add them into sintering. But in this way, the utilization factor of sintering and the quality of sinter decline while the energy consumption increases [3].Therefore, more advanced and efficient technology is needed to make the best of these iron resources. Cold consolidation of ferrous scrap is a simple process that has many advantages such as less investment, quicker effect, lower energy and lower cost [4-5] But the conventional maintaining period is too long, usually up to four-six weeks, and the pellet strength is low. Therefore, the key points of the cold-bonded pelletizing are to develop a new adhesive [4,5] to shorten the natural maintenance cycle and to improve the strength of the pellets. A method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing) is brought forward, and these cold-bonded pellets can be used as coolant in converter. After maintaining for 48h, these cold-bonded pellets can satisfy the mechanical requirements to replace the converter coolant [6]."

Jan 1, 2013

By C. I. Basilio

The mechanisms involved in the adsorption of modified thiol-type collectors on sulfide minerals have been investigated in the present work. These collectors belong to the broad classes of thionocarbamates, thioureas, thiophosphates and thiophosphinates. They differ significantly from the traditionally used thiol-type collectors, such as xanthates and dithiophosphates, in terms of structural features that involve either the introduction of an additional oxygen donor or the alteration of electron densities on donor atoms. Electrochemical studies suggest that the adsorption of these classes of collectors is probably the result of a coupled reaction of the EC-type, involving an initial electron transfer step (E), followed immediately by a chemical reaction (C). Thus, the overall adsorption process is controlled by both the E, and pK of the system. The role of structural features in changing the interaction of the donor atoms with sulfide minerals is also discussed.

Jan 1, 1991

By X. M. Chen

The selection of leach reagent mainly according to the ratio of useful mineral to gangue in mineral raw material and the structure of mineral raw material. Besides that the price of reagent, the capability of reagent decomposing mineral and its causticity on equipment is also supposed to be in regard. On common conditions, the scandium content in mineral raw material is low, even Sc concentrate of specimen-Yunnan rare earth ore which contain Sc used in this experiment only is 148 g/t. Moreover, in enlarging scale experiments the content of scandium in leach liquid is only 3.6g/t, meanwhile various and complicated impurity existing in it. At present, both domestic and abroad has succeed in enriching scandium from vitriol solution, while enriching scandium from hydrochloric acid only has been studied in some minority units, which is not reported to be practical in industry. Therefore, this item offer a new research issue on Sc?s extract, which is as well as the task of this research. Spectrum analysis, chemic component analysis and scandium content have been made in main mineral measurement on rare earth with Sc in the paper. Based on characters of sample, select hydrochloric acid, vitriol and nitric acid as leach reagent and make different blueprints to accomplish the experimental research about selecting leach reagent. In the aspect of rare earth leach scandium leach density is researched, leach liquid to solid rate, leach temperature, leach time, leach granule rate and leach solution. This experiment claims that in the optimal experimental ambience, leach rate of vitriol is 58.18%, the leach rate of nitric acid is 50.73% and the leach rate of hydrochloric acid is 59.34%. Among them, hydrochloric acid has the best effect, therefore this experiment choose it as the leach reagent.

Jan 1, 2014

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By Mark A. White

Arch Mineral has developed several computer programs that aid the surface mine planning function. These programs are utilized to perform long term projections for various area or semi-area stripping operations. The program generated reports include yardage, tonnage, quality and ratio information for the user-specified time periods. The projections are used to anticipate the annual budget, to compare alternative mine plans and to analyze acquisition candidates. The programs are user friendly, fast and accurate. Geological Grid File Two data files must be set-up and used in conjunction with the mine planning programs. These are a geological data file and a general input file.

Jan 1, 1984

By Aurel Goodwin

MSHA is the regulatory Agency which administers the Federal Mine Safety and Health Act. Although MSHA's principles largely derive from this Act, they do not exculsively derive from it. One might expect that our principles are contained in the regulations we have published to implement the Act. To a degree, this is true; but the regulations we have now were developed and published before the current Act became effective. For this reason, as well as others, there are some principles that we support which are not evident in our regulations, or in the Act. One of these is the ALARA principle. This principle requires that all unnecessary exposure be avoided; that is, all exposures should be kept "As Low As Reasonably Achievable." Almost all professionals in radiation control can agree with this broad principle; but it would be difficult to get agreement on a regulation which would translate the principle into industry practice. Rather, our regulations specify a limit to exposure for any individual. For radon daughters the current limit is four working level months per year. By having an explicit limit such as this, the ALARA principle often becomes lost and the limit becomes the goal. The principles contained in the Act are equally broad in scope. The principles apply not only for radiation protection, but also for toxic substances and harmful physical agents. The Act states that standards for such substances or agents shall most adequately assure on the basis of the best available evidence that no miner will suffer material impairment of health or functional capacity, even if such miner has regular exposure to the hazards dealt with for the period of his working life. The Act also provides that, although protection of health must be our foremost concern, other considerations shall be the latest scientific data in the field and the feasibility of the standards. Our regulations reflected similar principles when they were developed and promulgated. From experience with other health and safety laws, Congress realized that setting and meeting an exposure limit may not be sufficient to prevent disease. The Act, therefore, contains a detailed description of additional provisions to be included, where appropriate, in mandatory safety and health standards. One of these additional provisions requires that miners be informed about the nature of the hazards associated with their job and about the means for their own protection. Another provision requires the use of labels and other forms of warning to inform miners about the hazards, about proper precautions for safe use or exposure, about relevant symptoms of overexposure, and about emergency treatment. We have partially implemented these provisions through regulation. The Act requires also that standards shall prescribe protective equipment and control of technological procedures and that they shall provide for the monitoring of miners' exposures. We have implemented this provision to a degree also through regulation. Finally, the Act specifies that, where appropriate, a mandatory standard must prescribe the type and frequency of medical examinations in order to most effectively determine whether the health of miners is adversely affected by exposure. Additionally, when a determination is made that a miner may suffer material impairment of health or functional capacity by reason of exposure, that miner must be removed from such exposure and reassigned. In order to encourage miners to take the medical examination, the Act also provides that the miner shall not suffer loss of pay as a result of being reassigned. This additional provision on medical examinations has not been implemented by regulation for radiation hazards, nor for most other toxic substances or hazardous physical agents. We believe that this conference will provide us with valuable information on medical examinations for radiation exposure, as well as on other considerations to be used in future regulations. We still question whether our basic exposure standard of four working level months per year is adequate to protect a miner's health. This conference is indeed timely because both MSHA and NIOSH have been reviewing this issue for some time. I would like to reemphasize MSHA's commitment to education and training. MSHA strongly believes that miners should be informed fully about the real and potential hazards associated with their work. They should know the nature of the hazard and the means for protecting themselves from the hazard. The Act also emphasizes the need for training miners by requiring that new miners receive 40 hours of training before working underground and 24 hours of training before working on the surface. The Act also requires eight hours of refresher training annually. This training must include information on the relevant health hazards and the potential consequences of overexposure. Before I close, I would like to mention briefly another source of principles that MSHA often consults to obtain guidance for both the development and enforcement of regulations. These are the various court decisions that are handed down from time to time. Two in particular that I want to stress are the recent Supreme Court Decisions on benzene and cotton dust. Although neither of the decisions has a direct impact on mining or radiation, they do clarify some general principles and directions for regulatory agencies, such as the role of cost-benefit analysis and the need for risk assessment. In closing, I wish us all an open exchange of information for a productive and useful conference.

Jan 1, 1981

By R Nicholson, N D. Cox, N W. A Lambert

"This paper reports on the long-term operation of a particle density meter (PDM) at the Bloomfield coal handling and preparation plant (CHPP). This unit has been operating continuously for over three years, providing real-time data to the operators to allow the monitoring of flotation circuit performance. PDM outputs include slurry density, solids concentration on both mass and volumetric basis, and particle density. Knowing the average particle density of a stream allows for the optimisation of the process in real-time.The calibration of the solids concentration measurement device proved very difficult as the factory calibration techniques and existing laboratory analysis did not give accurate or reliable results. The solids concentration device had to be re-engineered and a new calibration method developed that gave accurate and repeatable results. Independent verification of samples taken from the PDM was undertaken as part of the trial process.The operational reliability of the PDM was a major point of investigation. The initial installation of the unit revealed issues with large, misplaced material of up to 20 mm periodically entering the unit, leading to feed blockages. The presence of these misplaced, oversized particles in the flotation circuit was resolved by installing innovative automatic back flush systems on the PDM.From a plant perspective the PDM has been an invaluable instrument that has enabled irregularities in the flotation circuit performance to be identified, which sampling had not and could not readily identify. This was achieved by close monitoring of real-time tailings composition on a minute by minute basis over short and extended periods. Variations in the tailings stream with respect to particle density and solids concentration were traced back to other issues in the plant. In addition, the PDM has allowed cell optimisation with respect to reagent dose rate to be improved. The PDM with real-time feedback can negate the need for large sampling campaigns and analysis during plant optimisation programs.Citation:Lambert, N, Cox, N and Nicholson, R, 2016. Particle Density Meter, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016