Search Documents

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

By I Gipps

Each of us has a vision of what the future mine will be and, generally, these visions have many similarities and some differences. One of the major discrepancies in visions of the future mine is not the ultimate goal but the path to achieve it. Many of the future concepts require a radical re-thinking of how things are and will be done yet. So how do we reach this visionary future mine? We need a path that satisfies both our future aspirations of a high tech gee-whiz operated from our iPads and the unfortunately mundane approach that says ‘we must know the method works, ie nothing new’.This paper explores how, within a research based organisation, we firstly set our ultimate goal and then divide the path into realistic technology development chunks that would appeal to mining companies to progress within their organisational constraints. Through examples, such as, automated LHDs, communications systems, surveying and localisation, rock cutting and geological sensing, we illustrate how this path will get us from the here and now to the out there future.This paper also demonstrates CSIRO’s short, medium and long-term research in many of the areas needed to create the Future Mine: mining methods, automation and remote control, mine communications, mapping and mission planning, geological sensing and, importantly, human-system integration, which examines how to effectively present data as information to operators and supervisors in an intelligent and useful manner.

Nov 22, 2011

By H Kim, J Park, J Lee

Silico-ferrite of calcium and aluminium (SFCA) is a bonding phase in the iron ore sinter. The phase transition upon melting of SFCA was investigated with Differential Scanning Calorimetry and Confocal Laser Scanning Microscope. The initial melting of SFCA occurred at 1183.2°C and a massive melting was found at around 1351.1–1358.2°C. A phase transition-melting was investigated at 1476.5–1478.7°C. The liquid phase was composed of immiscible phases. The present results would be utilised to design a new iron ore sinter for better processing performance in a hydrogenenriched ironmaking process.

Jun 19, 2024

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By Michel Mellinger

This paper presents preliminary results of a project aimed at obtaining a better understanding of the genesis of gold mineralization in northern Saskatchewan using lithogeochemistry. The properties sampled were: Weedy Lake (B Zone), Waddy Lake (Komis Zone) and Wedge Lake (Twin Zone) in the La Range belt, and the Rio mine in the Flin Flon area. Although the three vein-type deposits rudied here (Weedy Lake. Waddy Lake, Rio deposit) occur in different geological situation . a common gold deposition mechanism appears to have been active at all three location . Hydrothermal fluids carrying sulphur in solution in exces of gold thio-complexes moved through fractured host-rocks until they reached a site where pyrite precipitation wa triggered. As pyrite precipitated, the a/ aAu activity ratio of the fluid decreased. until a critical thre hold was reached and gold thio-complexe were de tabilized . resulting in the co-precipitation of gold and pyrite. The conditions triggering the precipitation of pyrite appear to have been: the abundance of iron in host-rock ~ilicates at Waddy Lake. and temperature decrease upon the reaching of structural trap~ at both Weedy Lake and the Rio deposit. with additional involvement of carbonatizationrelated reactions between fluid and host-rocks for the latter. In addition to pyrite precipitation , potassic alteration of the mafic metavolcanics is observed at Waddy Lake. while at the Rio deposit, the extensive carbonatization of the host-rocks i coupled with the deposition of chlorite that may have been remobilized from the altered mafic host rocks. In both the B Zone at Weedy Lake and the Komis Zone at Waddy Lake, a di tinct vanadium signature give some clue about the direction in which the hydrothermal fluids have moved . and the interpretation made is con istent with the geological ituation in either case. As for the Wedge Lake deposits, the distinct base metals-precious metals a sociation within a sulphide-facies iron formation confirm the volcanic exhalative origin of this gold mineralization .

Jan 1, 1986

By Chad Byron Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Aug 16, 2017

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace,4 the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is, although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace, the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By John Newby, Ulf Gwildis, Ken Massé, Guillaume Roux

How to connect an effluent conveyance tunnel to riser shaft and diffuser arms of an outfall system is dictated by the ground conditions, which ideally include rock or soil strata of low permeability. Where such favorable conditions are beyond reach, both the complexity of designing and the risk of constructing this crucial system connection increase disproportionally. This paper describes the considerations that went into the approach of connecting a 5-m-diameter TBM drive with the in-river riser shaft of the Annacis Island WWTP New Outfall System in the highly permeable Fraser River sands at hydrostatic pressures exceeding 3 bar.

Jun 23, 2024

By W. M. Myers

"The continued expansion of modern industry broadens the markets for minerals and their product. With these increasing demands new uses are being found for minerals that heretofore were considered as possessing no commercial possibilities. This tendency is reflected in the nonmetallic field in a constantly increasing demand for minerals formerly considered to be of scientific interest only, Furthermore, nonmetallic minerals of established commercial importance are used in new ways in various products, and this tends to expand the markets for these minerals. Some recent outstanding developments in applications of minerals are given in the following pages.The Andalusite GroupAmong the minerals that until recently were considered of scientific interest only, may be listed those of the andalusite group. This group is composed of the three minerals, andalusite, cyanite (or kyunite), and sillmanite, which are all forms of the compound Al2SiO5 (A1203, S1O2), and are therefore identical in chemical composition, but differ in physical properties,"

Mar 1, 1924

By B. B. Adhikari, S. Alam, Ohto Kawakita, Abe Pangeni

Effective recovery of gold was investigated by using adsorption gels prepared from pure cellulose, cotton and paper by treating with concentrated sulfuric acid. Only gold was adsorbed with extraordinary high loading capacity from varying concentrations of hydrochloric acid separated from other precious metals and base metals. The formation of fine powders of metallic gold was visually observed, which is attributable to the selective reduction of gold (III) ion to metallic gold clue to its high oxidation-reduction potential. Recovery of gold from the leach liquor of hydrochloric acid of circuit boards from spent mobile phones was attempted using pure cellulose gel.

Jan 1, 2011

By M Armony, J F. C L Costa, J C. Koppe

Linear kriging methods fail to estimate local grades and local reserves for highly skewed variables due to three reasons: it uses only part of the available data information, it has no physical principles associated with the mathematical proceedings to minimise the problems, and it works with continuous variables while data are discrete because of the limited precision of any equipment. The techniques commonly used up to now to solve the highly skewed variables estimation problems were unsuccessful, unless mathematical rigor is abandoned. Even the method of multiple indicator kriging is not satisfactory. This paper presents a new framework, the field parametric geostatistics (FPG) that transforms noisy variograms into well-behaved variograms and justifies mathematically empirical procedures commonly used, as trimming or capping arbitrarily very high values. The method, when applied to non-skewed variables, yields similar results to classic kriging. The methodology is illustrated in a case study at a gold deposit in Brazil, and compared to results obtained by usual techniques.

Sep 26, 2011

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022