Search Documents

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By Jheison Lopes dos Santos

Sistemas de blindagens multicamada têm sido estudadas pela sua ótima capacidade de proteção, devido à combinação de diferentes materiais que constituem seus componentes. A primeira camada é constituída por um componente cerâmico, cujo objetivo principal é fragmentar o projétil, dissipando grande parte de sua energia. A camada intermediária compreende tecido de aramida ou matriz polimérica com fibras naturais, que também dissipa energia tanto do projétil quanto do cerâmico e opera retendo os fragmentos cerâmicos. Neste trabalho, pela primeira vez, o sistema cerâmico Al2O3-Nb2O5-LiF tem seu comportamento dinâmico avaliado balisticamente. Este composto cerâmico foi submetido a impactos balísticos de projéteis 7,62 mm, para testar este cerâmico do primeiro componente de um sistema de blindagens multicamadas. Os resultados obtidos mostraram que a adição de LiF ao composto cerâmico Al2O3-4%p. Nb2O5, sinterizado a 1.300 ºC, obteve desempenho comparável ao obtido por Al2O3-4%p. Nb2O5 sem LiF, sinterizado a 1.400 ºC. Os resultados revelaram que, ao serem submetidos a esses impactos balísticos, apresentaram valores comparáveis aos esperados de pressão e de velocidade de partícula na interface de impacto projétil-cerâmico. Dessa forma, a adição de fluoreto de lítio ao composto cerâmico alumina-nióbia possibilitou a redução em 100 ºC na temperatura de sinterização, sem comprometer o desempenho balístico e exibindo parâmetros de choque comparáveis, e redução de custo.

Oct 30, 2017

By D. R. Derry

"IT WOULD TAKE a braver man than I to try to forecast the future of mining exploration far into Canada's second century. Even to look ahead ten or twenty-five years we must review the figures of the fairly recent past -and I have found this quite a time-consuming but interesting job -in order to find trends and project them into future years. The trends to which I will refer are: firstly, the annual expenditure on exploration and its relation to value of output; secondly, the discovery rate and its relation to production initiations; and thirdly, the methods by which discoveries have been, and will be, made. Exploration Expenditures Figures on the annual expenditure on mining exploration in Canada have been collected and published for some years by the Do-minion Bureau of Statistics. These have some unavoidable limitations; e.g., in the varying definition between one company and another of what comprises ""Exploration"" and in the difficulty of getting complete returns. However, although the actual figure for a given year may be subject to question, I believe that the relative figures from one year to another are reasonably reliable. There is also a lapse of time between the collection of data and publication -the last published figures are for the year 1963. In bringing the figures up to date to 1966 I have canvassed eight of the larger mining and exploration companies and obtained their figures for 1963 to 1966 inclusive, and then averaged these for each year and applied the progression to the 1963 figures."

Jan 1, 1968

By A Marton

Concerns with crest losses have seen changes to a number of design and operating parameters to retain the integrity of the wall and the berms of the Kidston Gold MinesÆ Eldridge Pit. Until trials began in 1999 most final wall designs utilised large diameter blastholes up to the presplit row to achieve the wall angle. The berm crests were being lost, wall support requirements were increasing and affecting mining schedules and several fault areas were putting pit access at risk. Standard designs had been determined during the early mining years and while periodic modifications had been made there was a need for major blast pattern revision. This paper traces the development of wall control blasting programs over the years, relating designs to the geology and the evidence in the walls with the theories of the day and includes the recent trials that were conducted in what is a most unforgiving geology. Trials and improvements to ensure the walls were safe were conducted even as the mine neared its economic life. Instrumented monitoring of trials blasts has greatly increased the understanding of the damage criteria and enabled rapid revision of designs. Recent changes included reduction in presplit energy, charge redistribution and use of smaller blast holes for the trim patterns. Determination of a minimum proximity-to-final wall limit for production blastholes, establishment of the correct standoff to berm crests and walls and selective use of presplitting techniques for protecting crests have resulted in cost effectiveness, improved bench crest retention and an overall reduction in visible wall damage.

Jan 1, 2001

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Grinding is one of the most energy consuming unit operations and is also a very inefficient and costly process. Therefore, it is of great importance to run the grinding process as efficiently as possible. The most common way today to control grinding processes is by measuring the power draw of the mill and try to keep it at a maximum level. However, some studies (Kawatra, 1989, Koivistoinen, 1989, Moys, 1989) have shown that this measurement doesn.t reflect everything that takes place inside a mill. Among other parameters like slurry rheology, temperature and charge behaviour, the volumetric filling of a grinding mill seems to have a large influence on the grinding efficiency (Herbst, 1988, Koivistoinen, 1992, Vermeulen, 1988). A problem in attempting to measure those parameters has been to get a sensor that is both robust and sensitive enough for continuous on-line measurement.This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a DEM modelling technique is used.The results indicate that the system is capable of following the normal variation that occurs in the mill. The signal also very well reflect changes in operating variables such as ball charge level, pulp density and rotational speed. By studying the nature and different features of the signal one can get a better understanding of milling circuit dynamics. Another feature of the technique is the possibility for an operator to continuously follow the grinding process and thereby run the process under optimal conditions."

Jan 1, 2003

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By Gerald K. Vellente

Producers of strip coated products are being approached by users to supply higher quality products and adhere to tighter specifications. Suppliers, in an attempt to assist the producers, must consider new technologies for equipment. In the past several years, the induction melting and heating industry has made great strides in developing new and innovative equipment, while improving existing technology. In the past several years, the induction melting and heating industry has made great strides in developing new and innovative equipment, while improving existing technology. In the past several years, the induction melting and heating industry has made great strides in developing new and innovative equipment, while improving existing technology. This paper will review recent developments to include improved refractory systems for ceramic pots, new channel-type inductors which are more efficient, new power control systems for existing channel-type pots, and innovative use of multi-purpose lines. Additionally, new heating applications such as galvannealing, edge heating, and post heating will be reviewed. Advanced math models for controlling heat will be discussed. Producers can easily meet the demands of their customers because of the flexibility provided by the equipment reviewed.

Jan 1, 1992

By Donald J. Hill

To be successful, every organization within the mining industry must involve itself in researching and evaluating methods of loss control. The appraisal and evaluation of accidents and injuries is required to determine the costs of loss producing practices and conditions. This involves all of an organizations disciplines that concern themselves with a more efficient and cost effective organization. To come to know the cost of your safety program or how much is expended yearly for each employee on safety; to know what your safety costs are per man-hour or per ton-produced; to know what the health, medical and compensation costs are for any given incident are just a few of the important facts and figures that the safety management of a given organization needs to know to operate in the mining industry today.

Jan 1, 1984

"This paper deals with the reconciliation of open stope performance at Olympic Dam, South Australia, with a focus on stope stability, recovery, and operational aspects of stope reconciliation in relation to the expected or planned stope design. The observed stope performance is inconsistent with the equivalent linear overbreak sloughing criteria for assessing the performance of large open stopes. The aim is to investigate new stope performance criteria using quantitative (overbreak, underbreak, maximum depth of wall failure) and qualitative (stope productivity, observed fragmentation) information that correlates with the observed stope behaviour, providing a process for improving future stope designs.RÉSUMÉ Le présent article traite de la réconciliation de la performance des chambres ouvertes à Olympic Dam, Australie du Sud, en ciblant la stabilité des chambres, la récupération et les aspects opérationnels de la réconciliation des chambres par rapport à la conception attendue ou planifiée des chambres. La performance observée des chambres ne concorde pas avec les critères d’épaisseur équivalente du bris hors profil pour évaluer la performance de grandes chambres ouvertes. L’objectif est d’étudier de nouveaux critères de performance des chambres au moyen de données quantitatives (rupture hors profil, rupture à l’intérieur du profil planifié, profondeur maximale d’effondrement du mur) et qualitatives (productivité de la chambre, fragmentation observée) qui concordent avec le comportement observé des chambres, fournissant ainsi un processus pour améliorer les futures conceptions des chambres."

Jan 1, 2015

By Meredith Scaggs, Emily Sarver, Lucas Rojas Mendoza

"Early on Jan. 9, 2014, approximately 37,800 L (10,000 gal) of crude 4-methylcyclohexanemethanol (MCHM) leaked from a storage tank sitting on the bank of the Elk River near Charleston, WV (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal and is considered nonhazardous in terms of transportation, storage regulations and also toxicity (CDC, 2014a). Freedom Industries Inc., a producer and vendor of specialty chemical products, had acquired the storage facility from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein and McWhirter, 2014).The spill site was located a little more than 1.6 km (1 mile) upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a "Do Not Use" order was issued for all customers (WVAW, 2014a).With little information readily available regarding the potential human health effects of MCHM, the U.S. Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the "Do Not Use" order remained in effect for a total of eight days, until Jan. 17, when the WVAW distribution water was confirmed to have MCHM concentrations below the approved level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at sub-ppb concentrations, a fact that undoubtedly added to growing public concern (Rosen et al., 2014; Gallagher et al., 2014). In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until Feb. 25 when MCHM levels were measured below 2 ppb (WVAW, 2014b), and eventually replaced the affected filter media (WVAW, 2014c)."

Jan 1, 2014

By Richard S. Olsen

Prior work by the Bureau of Mines demonstrated a feed preparation method that eliminates the formation of slime during leaching of calcined kaolinitic clay and makes leached residues fast settling and easy to filter. Nitric acid leaching rates determined for calcined kaolinitic clay prepared by this method were found to correspond to a zero-order reaction model for both batch and continuous, stirred-tank leach-ing. A rate constant of 0.136 min-1 was determined. Separation of solid residues from the reacted slurry was examined, and filtration rates were determined. Permeabilities of the flocculated, leached residues were around 51 darcys, or 5.0 x 10-7 cm2 for laminar flow through 4-ft-deep beds.

Jan 1, 1983

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By W. A. Smith, M. C. Bekker, C. Marnewick

Projects or project-orientated approaches have become a common form of work in nearly all sectors of economies. This has led to concepts such as ‘projectified’ and ‘project orientated’ organizations. By defining projectification of a company, industry, or economy as the share of project work in total work, one can reasonably determine the impact that project management, and by default projectification, has had on that company, industry, or economy in terms of staff optimization and allocation. This paper presents the results for such a projectification study of the South African mining industry. This sector has long been a significant contributor to the country’s economy from a gross value added (GVA) and employment point of view. Understanding the impact of projectification and the project management way of work on this industry may potentially add significant value to both the mining and project management knowledge areas. We show that although the mining industry is considered by some to operate in archaic ways, the level of projectification has increased over time, and now represents approximately one third of all work conducted.

May 1, 2021

By S. K. Kawatra, H. J. Haselhuhn

"Thickening is used during two primary mineral processing operations: water removal and desliming. During water removal, the pulp density is increased through the injection of flocculants. These flocs settle and create a dense pulp while clarified water is removed through the overflow. During desliming, fine particles are removed through the overflow. Desliming can also be used as a mineral separation process known as selective flocculation-dispersion, where valuable minerals are flocculated and gangue minerals remain dispersed and exit through the overflow.There are many ways to analyze thickener performance on a laboratory scale, but these analyses often do not correlate well with full-scale performance. Some pilot-scale systems have been designed using a semicontinuous approach, but the amount of material required to perform their tests can make semicontinuous pilot thickeners impractical for most applications. This paper focuses on the design and optimization of a continuous pilot-scale deslime thickener that requires minimal material to operate. The design, optimization strategy, and an example study of reagent selection are demonstrated. IntroductionMany laboratory methods have been employed to size and optimize thickener performance. The most common of these include the Coe and Clevenger method and methods derived from the Kynch theory of sedimentation. The Coe and Clevenger method was developed in 1916 and was proven for slurries that do not require flocculation to settle. This method proposed that the settling rate of the pulp is only a function of the solids concentration. It is executed by creating slurries of several different concentrations of solids and performing bench-scale settling tests in graduated cylinders. For each concentration, a thickener unit area can be determined using the following equation (Coe and Clevenger, 1916; Laros, Slottee and Baczek, 2002):"

Jan 1, 2017

By Zhian Liang, Xiong Huang, Weixin Wu, Lifeng Cui, Zhuanhua Wei, Guoyao Li, Xiao Ni, Junrong Wang, Shuiping Zhong

ZJ 201 (modified starch) is a non-toxic, odorless, and biodegradable polymeric depressant, which selectively depressed galena in batch flotation tests while chalcopyrite was not significantly affected. In a plant trial, copper-lead separation was successful for the first time without using dichromate. Moreover, the plant process could be changed to sequential Cu-Pb flotation using ZJ 201 for higher grade lead concentrate. A copper concentrate was obtained with a Cu grade of 24.91% and a Pb grade of 5.11%, which recovered 76.6% of the copper from the original ore; a lead concentrate was also obtained with a Pb grade of 21.90% and a Cu grade of 5.31%, which recovered 52.6% of the lead. In addition to the effective copper-lead separation observed in the plant trial, another improvement observed is that gold was recovered mostly in copper concentrate, which could be sold for higher prices. Au grade reached 230.64 g/t, and its recovery reached 65.8% in the copper concentrate. Au grade in lead concentrate was only 18.90 g/t.

Aug 27, 2021

By R J. Longbottom

In this study the bonding within reduced titanomagnetite-coal compacts was investigated. The aim of the study was to better understand the binding mechanisms in the reduced compacts and, based on this understanding, to improve on their strength.Titanomagnetite ore was combined with sub-bituminous coal to form compacts. The compacts were then reduced by heating in a thermogravimetric furnace (TGA) to temperatures between 1000 - 1300°C under argon. The reaction progress was monitored by measuring the weight loss with time. The reduced compacts were found to have low strength in compression testing. The main form of bonding between the reduced titanomagnetite particles in the compact was by the formation of a slag-like material. Increasing the fi nal reduction temperature was found to have a profound effect on the strength of the compacts by promoting the formation of this slag-like material.Attempts to improve the strength of the compacts were made by changing two variables, the type of coal and the addition of rice husks. The addition of coking coal gave reacted samples that had little strength, while the addition of rice husks may have enhanced the strength of the reduced compacts.

Jul 11, 2011

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

By Raghoottma S. Pandurangi, Mohindar S. Seehra

"The interaction of amorphous 1ilica particles with several hydrogen bonding agents (H2O, C2H5OH, C7H2NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy. It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction or surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C7H2NO > C2H5OH > H2O. Index Headings: Silica; Surface vibrational modes; Photoacoustic spectroscopy; Hydrogen bonding agents.INTRODUCTIONThe use of m spectroscopy to study the adsorption on solid surfaces is well documented in the literature.1 2 For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1• Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-5 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity, 7- 9 catalysis, 10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8NO), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by m spectroscopy, and Knozinger16 and Rouxlet and Semples11 have used transmission m spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties. In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18•19 Moreover, according to a recent paper, 20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry. In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H50H, and H20) with the silica surface by monitoring changes in the surface m modes. Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents. Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16•17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification. Details of this work are given below."

Jan 1, 1990

By X Zhang, B McFadzean, C T. O’Connor, S Pikinini

The Platreef in South Africa contains one of the world’s largest reserves of platinum group elements. One of the major platinum group minerals (PGM) components in this ore is sperrylite (PtAs₂), which has been found to be slow floating compared to the other PGMs. In a study aimed at determining the reasons for the poor floatability of sperrylite and to improve its recovery, tests were carried out to determine the interactions of the mineral with a range of standard and novel collectors. Microflotation tests were carried out to determine the hydrophobicity of the minerals before and after adsorption of collectors. In addition, experiments were carried out to determine the enthalpy and extent of collector adsorption on the minerals and to investigate electrochemical interactions between sperrylite and selected standard collectors. The results indicated that poor collector adsorption was the major cause for the poor floatability of sperrylite. Sperrylite had both poor natural (14.5 per cent) floatability and collector-induced flotation recoveries, the highest recovery of 26 per cent being observed using PNBX collector at pH 9. Moreover, the rest potential tests showed that the interaction of sperrylite with standard collectors such as xanthates was poor. The decrease in potential after the addition of the standard collectors ranged from 7.9 mV to 24.9 mV under alkaline conditions. Furthermore, sperrylite rest potentials remained unchanged with a change in pH from basic to acidic, indicating its resistance to surface alteration. Surface alteration of the minerals is key for the chemisorption of collectors to take place on the mineral surface. This was further emphasised by flotation recoveries at low pH, where only certain collectors responded positively to a decrease in pH and these were shown to have undergone a structural change. This work has highlighted the difficulties associated with sperrylite flotation and provides some direction for future research.

Aug 24, 2022

"Ore deposits containing rare earth elements normally contain small amounts of the radioactive elements thorium (Th) and/or uranium (U). These are the naturally-occurring isotopes U238, U235, and Th232 (and associated decay-series daughter products) that are ubiquitous in nature, and that contribute a small percentage of the natural background radiation exposure encountered by humans. The presence of these radioactive materials in the ore deposit creates potential hazards to human health and the environment that must be dealt with properly in the mining, processing, and refining of the ores, as well as management of waste streams and residues. This paper presents an overview of the environmental and safety issues associated with U and Th, with particular emphasis on rare earth mining, processing, and refining projects; the regulatory approaches followed to ensure that rare earth deposits are developed, operated, closed, and decommissioned safely; and the development of information during the project predevelopment work and permitting processes that feed into the design, operation, and closure of tailings impoundments and milling/separation/refining facilities. Case studies will be presented subject to the availability of relevant public information. INTRODUCTIONNearly all ore deposits containing economically-recoverable rare earth minerals also contain small amounts of the radioactive isotopes for the elements thorium (Th) and/or uranium (U) and their associated radioactive decay products. Therefore, the handling and management of these materials in mining and mineral processing operations must be performed so that workers and the environment are protected from harm from Th and/or U (and their radioactive decay products), just as they must be protected from any other potentially harmful constituents present in the ore or introduced in processing. Examples of these might include ores with high sulfide content, which may pose a risk of acid rock drainage, or chemicals used in ore processing and metals production.The purpose of this paper is to present information on how rare earth mining and processing projects with ores containing Th and/or U can be developed, operated, and decommissioned safely according to applicable regulations intended to protect worker health & safety and the environment.It should be noted that some countries are considering developing Th as a feedstock for producing nuclear energy, which could have some effect on future development of rare earth ore deposits. To avoid confusion, that issue is not discussed in this paper."

Jan 1, 2012