Search Documents

By N. A. C. Smith

[The beau of Mines made its first survey of motor gasolines sold throughout the United States in 1915, a second in 1917, and a third in April. 1919. These surveys shored that motor gasoline had become notably less volatile during each two-year interval. In order to ascertain whether this change was continuing, it was planned to institute semi-annual surveys, the first of which teas made in January, 1920. Contrary to expectations based on the previous surveys, the average volatility of the gasoline tested at this time was practically identical with that of the average volatility of the gasoline from the same districts in 1919. The next survey, made in July, 1920, showed a very marked decrease in volatility but as it has long been recognized that the volatility of motor gasoline manufactured for sale during the summer months is loss tan that of gasoline made and sold during the winter, part at least of the change was attributed to this factor. The average boiling point of the samples collected in the present survey is 263 degrees Fahrenheit, as compared with 264 a year ago. This shows that the average gasoline marketed at the present time is fully as volatile as that marketed a year ago. There has been, however, a noticeable change in the character of the product: the initial boiling point and 20 per cant point are lower than a year ago, whereas the 90 per cent and end-points are higher, which indicates a greater proportion of gasolines made by blending casing-head, or natural gas-gasoline, and naphtha.]

Jan 1, 1921

By C. W. Van Noy

The procedure suggested in this report is intended for the use of engineers, esters, accountants, etc., in estimating the cost of chemical-type operations. It is intended to over operating costs, not investment costs, as the latter have been covered numerous other publications. However, as capital investment costs are reflected to a high degree in operating costs, it is important to point out that accuracy of investment costs is highly essential. Therefore, all factors that might be included under plant -capital costs should be considered, such as requirements of shops, employees' housing, etc. The procedure is designed primarily for use in types of chemical oper¬ations, such as the production of synthetic liquid fuels, anhydrous ammonia, and others of like or similar nature. Yet, no attempt has been made to cover the entire chemical industry.

Jan 1, 1949

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By Adusumilli M. S, Subrahmanyam T. V, Rao V. D

Chance find of an economically important mineral on the sur- face and its exploitation without proper exploration work, has become the habit of humanity since the Bronze Age. The explora- tion and exploitation techniques have, however, been substan- tially improved in the technologically developed western world and system controlled major communist countries. Nevertheless, the greatest need is felt in the Third World countries where large mineral potential exists, but with inadequate investments in exploration and exploitation techniques, a handicap that has been beneficial to the more developed countries, since long. The great number of the Third World countries which are striv- ing hard to develop, need to formulate mineral exploration and exploitation strategies which could enable them to develop their resources. This requires planning and creating new concepts of ore deposit types and genetic models, rheology, economics and their innovation and integration. The following approach could help them to be economically "more independent" by the end of this century. 1. Bridging of pure and applied geology gap, and creating con- sciousness of research and development. 2. Revision of mineral resources concepts adopted to modern technological world. 3. Improved mineralogical research, and determinative miner- alogy as an important asset. 4. Creative research and establishing know-how, with philosophical base for regional exploration projects. 5. Indepth investigation into the origin and growth of earth as a system, and its importance in the association, quality, and quantity of metallic, non-metallic and energy resources con- centrations. 6. Mineral beneficiation, targets and strateties; methods of eco- nomic and improved recovery systems. Development of alter- native technology, and utilization of mineral technology strategies. 7. Theoretical and practical modelling by conventional and com- puter techniques of the existing and expected mineral resources, and mineral development. 8. Critical analysis of the status of mineral economics of the Third World and developed world with forecasts for the year 2000 based on problems faced by the developing world. 9. Minerals at cross roads of International Interdependence. 10. Philosophical, realistic, traditional and modern strategies for mineral development. The dynamic economic system opera- tion in national mineral sector.

Jan 1, 1988

By Pinter R

Several major routes connecting Northern and Southern Europe or Asia run through Austria. These highways have to surmount the alpine range which traverses Austria from west to east. In order to ensure safe driving conditions even in winter, tunnels, at times quite long ones, are necessary. Austria now has tunnels totalling 160 km in length. These tunnels are either already in use or just about completed. The Plabutsch tunnel near Graz will be one of the longest tunnels in the world: approximately 10 kilometers in length. It will be put into operation in the summer of 1987. Before construction could begin, soil and rock conditions had to be investigated by means of a test tunnel. Afterwards, excavation was begun to the full 100 m' cross section. The new Austrian tunnelling method with conventional blasting was used for the major part of the tunnel. It was necessary to have such a large tunnel cross section because a fully transverse ventilation system is installed for environmental reasons. In order to avoid air pollution from the tunnel, exhaust fumes are not allowed to escape from the tunnel portals but from two shafts, each with a diameter of 8.5 m. In this way, exhaust fumes must rise 90 meters or 240 meters before they reach the open air and will thus not affect the city. The ventilation system influences the size of the excavation, and especially the size of the ventilation caverns and the air shafts. All these factors directly influence construction and maintenance costs, and an economical optimisation leads to the appropriate dimensions for the excavation.

Jan 1, 1987

By D. T. Jr. Tarr

History of Development The hydrocyclone, probably because of its basic simplicity, has been used for various classification applications since before 1890. A patent was granted in the United States in 1891 to Bretney on a device for separating sand from water, collecting the sand in a closed chamber for intermittent discharge, practically identical to some present-day water desanding cyclones. Between 1900 and 1937 there were 30 or more additional patents issued on liquid cyclone configurations or their use. About 1937 liquid cyclones began to be used commercially in the treatment of cellulose fiber in the pulp and paper industry separating contaminating particles from the fiber in water suspension used for making high grade paper products. Nichols Engineering & Research Corp. of New York was marketing a liquid cyclone for cleaning sand and din particles from fiber suspensions in the pulp and paper industry by 1937. The designs during this period were such that the cyclones discharged a small amount of relatively high density material into a chamber connected to the cyclone apex which in turn discharged the collected dirt material intermittently. By the early 1940s hydrocyclones as we know them today began to appear both in the pulp and paper industry and in coal prorzssing.18 Considerable experimental work was done on small, mostly 3-in.- diam, cyclones operating at relatively high pressure drops, in the range of 50 psi, to remove very small contaminating particles from cellulose fiber in the production of high-grade writing papers in the paper industry.18

Jan 1, 1985

By Jorge Blázquez, Paulo Couceiro, Patricio Vergara, Luis Martínez, Juan Navarro

This study introduces the X-2Mill solution, a refined two-step methodology aimed at optimizing blast designs by aligning explosive energy with rock properties. The approach employs the X-4Traits Model, which uses drill-monitoring data from both autonomous and manual drilling modes to develop two critical indexes: the Drilling Rock Factor (DRF) and the Drilling SAG Power Index (DSPI). The DRF integrates the Size-Energy Fan Model with rock fragmentation results and blast design parameters, while the DSPI adjusts Specific SAG Energy (SESAG) based on Bond’s theory, incorporating ore X80 results, SAG mill capacity (TPH), and power draw to estimate milling difficulty. To enhance prediction accuracy, the X-2Mill solution incorporates, to a Principal Component Analysis of the normalized drilling data, a Meta Machine Learning model with a 3D spatial function, accounting for information from surrounding drill holes. This integration improves the precision of the DRF and DSPI estimates. The methodology unfolds in two main steps: Step 1: Bench-Scale Pattern Design, involves defining the target P80 size for ore based on the SESAG and the DSPI. It also establishes target X80 sizes for waste and oxide materials and iterates to determine the optimal Burden x Spacing (BxS) using the Size-Energy Fan Model and the DRF. Step 2: Blast-Scale Selective Explosive Density/Energy focuses on refining explosive density on a hole-by-hole basis to achieve the specified X80 values for ore, waste, and oxide materials. The X-2Mill Solution was developed at Minera Escondida Limitada (MEL) using data from 162,761 blastholes across 356 blasts conducted over three mine expansions. This solution addresses the challenges of blasting harder and more difficult rock, particularly in the lower levels of the mine. By adapting the blast pattern and explosive density to the specific rock properties and ore/waste designation, the X-2Mill Solution aims to achieve precise size distributions and improve overall blasting performance. The results demonstrate that the X-2Mill Solution balances ore fragmentation to meet SAG mill throughput requirements while optimizing powder factor costs for waste material and maintaining digging efficiency. By efficiently distributing explosive energy, the solution not only enhances throughput but also improves blasting efficiency while ensuring stable slopes and minimizing fault activation.

Jan 21, 2025

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By J. H. Howard

The purposes of this report are to summarize the findings of the Committee on the Challenges of Modern Society Non-electrical Project (a working committee of the North Atlantic Treaty Organization) and also, thereby, to provide an introduction and review of the current situation regarding non-electrical applications to those who are interested in the subject.

Jan 1, 1975

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coals; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fourth of a series of reports giving the results of studies by counties under phase (1) of the investigation. It covers Armstrong County, Pa., which comprises parts of the Foxburg, Clarion, Brookville, Kittanning, Bural Valley, Smicksburg, Freeport, Elders Ridge, and Indiana quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and more than 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By A. C. Fieldner

In the course of its investigations on the properties of coal and in rendering fuel-inspection service to other agencies of the Government, the Bureau of Mines has accumulated a comprehensive file of coal analyses that includes data on virtually every coal field of commercial importance in the United States. As knowledge of the composition of coal is potentially valuable to every user of coal, the Bureau publishes its analytical records. Before 1921 such publications contained analyses of coal from all parts of the United States; individual analyses or average analyses of a series of shipments of coal were given with the name and location of the mine producing the coal. Beginning in 1921 the analyses were published by separate States because the quantity of data had become so great. The separate papers published to date, with Bureau of Mines Technical Paper numbers, are as follows: Alabama, 347; Arkansas, 416; Colorado, 574; Illinois, 634 and 641; Indiana, 417; Iowa, 269; Kansas, 455; Kentucky, 30S; Maryland, 465; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344; Oklahoma, 411 ; Pennsylvania (bituminous), 590; Tennessee, 356; Utah, 345; Virginia, 365; Washington, 491 and 618 (618, published in 1941, supplements 491); West Virginia, 405 and 626; and Wyoming, 484. From time to time the various papers will be revised to include later analyses and other data. The Bureau of Mines annually receives many inquiries as to the composition of coals obtained from specific localities or, conversely, as to the localities from which a given kind of coal may be obtained. This paper presents a summary, in tabular form, of the composition of commercial coal resources of the country. Specimen analyses are given exemplifying the analysis of coal mined in each coal-producing county, or, where it was feasible, coal from each bed in each county; also, ranges of analyses, within which the composition of most of the coal represented will fall, are given where there were enough analyses to permit satisfactory determination of the ranges. In addition, the degree of metamorphism from lignite toward anthracite of much of the coal is indicated by the classification by rank. This classification reveals to more experienced users of coal some of the general properties of coal, that is, whether the flame will be long or short, whether the coal will cake in the fire, and how it is likely to behave on exposure and in storage.

Jan 1, 1942

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By Betty J. Laswell, Gerald W. Laswell

If recent trends in the rotary drill market are indicative of future surface mining operating practice, then the move to scaled-up mining equipment by manufacturers may soon be over. Of the 48 different rotary drills currently produced by 12 manufacturers, over 60% were introduced within the past five years. By far, the new drills have been in the "small" class, capable of producing up to a 229-mm-diam (9-in.) blasthole with 222 kN (50,000 lb) or less of down pressure. New rotary drills in the "large" class, capable of producing a 311-mm-diam (12 1/4-in.) blasthole with up to 423 kN (95,000 lb) down pressure, have also been prominent. In the super-size category, new drills producing blasthole sizes to 444-mm-diam (17 1/2-in.) with up to 578 kN (130,000 lb) have been minimal.

Jan 7, 1978

By E. Chisakulo, M. W. Songolo, E. K. Chanda

Zambia’s mining industry has undergone various phases of mineral royalty changes since privatisation. Unlike many analyses that relied on subjective probability, this study employs the cut-off grade and mineral royalty model relationship to investigate how changes in mineral royalties impacted the net present value and cut-off grades of Zambian copper mines between 2008 and 2022. The results showed that net present value decreased by 10.39%, 6.13%, 9.69%, and 6.13% for Barrick Lumwana, Kansanshi, Nkana–Mopani Copper Mines, and Mufulira–Mopani Copper Mines, respectively, while First Quantum Minerals Trident’s net present value increased by 3.40%. Reductions in NPV correspond to higher government revenue, whereas the increase for FQM Trident reduced government revenue. For cut-off grades, returns increased by 0.42%, 1.20%, and 0.42% for Barrick Lumwana, First Quantum Minerals’ Trident, and Kansanshi, respectively, showing how portions of the Zambian copper orebodies accrued to investors, with a corresponding reduction in government revenue. Conversely, reductions of 0.24% and 0.38% for Nkana–Mopani Copper Mines and Mufulira–Mopani Copper Mines indicate that a share of the ore reserves accrued to the government, reducing investor returns. These findings demonstrate that mineral royalty adjustments redistribute economic value between investors and the government, affecting both profit margins and operational decisions. Despite these distributional effects, all projects remained economically viable. The findings underscore the need for an optimal mineral royalty framework that equitably balances the economic value of mineral resources between investors and the state

Jan 30, 2026

Early in 1936 the Interstate Oil Compact Commission and other groups interested in forecasts of demand for petroleum requested the Bureau of Mines to make a physical inventory of crude-oil stocks in the United States. Accordingly, the 74th Congress -appropriated funds for conducting such a survey during the fiscal year ended June 30, 1937. In the discussions end hearings2/ relative to the need for the survey, the opinion was expressed that crude oil held is storage for long periods had lost so much of its gasoline content that the economic significance of total stocks should be discounted materially. Therefore, a primary objective of the survey was to

Jan 1, 1938

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By N. Hamlef

In this study, the effects of heat treatment on phase formation and surface morphology of the Cr-Pt coated system are investigated using X-ray diffraction and electron microscopy techniques. The CrPt andCr4Pt (Cr3Pt - A15 type) phases were formed after heat treatment of the coated samples. Heat treating at 1000°C renders a distinct island coating morphology that is non-continuous in nature. A diffusional model is proposed for this coated system with regards to the surface morphology formation after heat treatment.

Jan 1, 2014