Search Documents

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By Yuezhen Zhou, Zewei Liu, Dachun Liu, Chongfang Yang, Wenlong Jiang, Fansong Liu

A novel process that the combination of vacuum decomposition and acid leaching was proposed. The influence of distillation times, diameter and thickness of the feeding material on the mass fraction of Molybdenum (Mo) and sulphur (S) in residual was investigated. The influence of leaching temperature, leaching time, concentration of hydrochloric acid solution, and ratio of liquid to solid on leaching rates of Mo and S in acid leaching process was also investigated. Due to the fact that SO2 emission happening in the long process of traditional molybdenum metallurgy could be avoided in this novel method, this combination process was environmentally-friendly. Molybdenum powder was obtained through handling molybdenite concentrate under the optimal condition parameters, and the mass fraction of Mo reached 98.29 wt%. So it's feasible to produce molybdenum powder from molybdenite concentrate by using this new method.

Mar 1, 2017

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By Arthur Dubé

An account is given of the developments brought about in the last fifteen years by metallurgical research in the field of heat treatment of steels. The practical aspects of these developments are especially emphasized. Methods of representation of the phase-change during austenitizing and sub-critical transformation of austenite are described and the importance of time-temperature-transformation charts for the planning of heat treatment cycles is shown. Special copies such as retained austenite and internal stresses developed on quenching are also discussed in some detail. Due to the interest shown currently in these problems, it has been thought advisable to describe briefly the underlying principles and present some of the results already available.

Jan 1, 1945

By Savory P. J

Uranium mining operations commenced at Ranger mine site, Jabiru NT Australia in May 1980. The Ranger orebodies, totalling approximately 110 000 tonnes contained U305 had been indicated by airborne radiometric survey in 1969 and confirmed by drilling the following year. Both diamond and percussion drilling methods were used to define the mineralisation and samples were analysed using a combination of radiometric and neutron activation techniques. Ore reserve estimates were calculated from conventional and geostatistical methods, and following the mining of 15 million tonnes of ore, reconciliations with before mining estimates are well within acceptable industry standards. In-pit grade control employs radiometric techniques including a radiometric truck discriminator built in Australia to mine specification to meet production requirements and improve productivity. Environmental requirements associated with uranium mining are a daily consideration.

Jan 1, 1993

By D. C. Dahlin

The U.S. Bureau of Mines investigated the magnetic susceptibility of minerals as a function of mag-netic field strength to determine how it might affect the potential for high-field magnetic separation as an alternative to other separation technologies. Single-mineral concentrates were prepared from specimens from the same deposit to compare magnetic susceptibilities of minerals that occur together and from specimens from different deposits to compare magnetic susceptibilities of like minerals. A vibrating-sample magnetometer with a superconducting magnet capable of producing a magnetic field of 7.16 x 106 Aim (90 kOe) was used to measure the magnetic moment of the samples. The data were then converted to specific magnetic susceptibility data and plotted as a function of magnetic field strength. Cursory studies were also completed on the effects of iron content and oxidation roasts on magnetic susceptibility in high fields. The results showed that magnetic susceptibility is essentially constant in magnetic fields above those needed to saturate ferromagnetic constituents. Although magnetic susceptibility is influenced by iron content and by thermal treatment, the changes are not large enough to influence separations in fields above 1.59 x 106 Aim (20 kOe).

Jan 1, 2010

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.

By T. J. Chen

Stone coal containing vanadium is an important vanadium resource in China. Roasting and oxidation of vanadium is the foundation for extracting vanadium from stone coal. This article takes stone coal vanadium ore in Tongshan of Hubei Province as research target to conduct oxidation roasting test on it by using a self-developed low-sodium compound additive and a new optimized technology. Firstly, use potentiometric titration, X diffraction, energy spectrum and electron probe to study valence change, occurrence and phase transition of vanadium during oxidation roasting process. On this basis, primary work is done on oxidation kinetics of vanadium by exploring the steps that control reaction rate during vanadium oxidation process and determining the related dynamic parameter ? apparent activation energy. The study shows that occurrence of vanadium in stone coal of Tongshan is mainly in illite, and that the result of phase transition in roasting process is disappearance of illite containing vanadium, formation of soluble vanadate and potassium feldspar, albite. It further demonstrates that oxidation process of vanadium is step by step (V(?)? V(?)? V(?)), and its oxidation reaction is controlled by diffusion kinetics whose dynamic apparent activation energy is E1=81.19kJ.mol-1.

Jan 1, 2014

By Arno C. Fieldner

Six years ago, I addressed the annual meeting of the American Society for Testing Materials on "Fuels of Today and Tomorrow."3/ Since then, our country has been drawn into another great war of veritably global extent, with unprecedented demands on fuels, foods, and materials in general. My purpose in this address is to review the changes in fuel supply and demand since 1937 and to give you my views on the outlook for the future. CONDITIONS IN. 1237 Daring 1936 the United States produced and consumed one-third of the world production of coal, two-thirds of the petroleum, and about 95 percent of the natural gas. Two-thirds of the oil produced in all countries since the discovery well was drilled in 1859 had come from American wells. With the exception of the three depression years 1931, 1932, and 1933, new oil reserves were being discovered since 1924 well in excess of our increasing rate of consumption. Discoveries of natural gas, likewise, were tremendous in volume, and this fuel was being transported to most parts of the country by pipe lines; some of them more than 1,000 miles long. We had all kinds of mineral fuels in abundance and at prices that did not stint anyone in the maximum utilization of the mechanical devices that were being developed on every hand. No one suspected that the time might come in a few years when, gasoline would be doled out to some of us at the rate of 1-1/2 gallons a week or that many of our fuel-oil furnaces would have to be converted to burn coal. Of course, these restrictions are due to unusual war conditions, such as lack of coastwise tanker transportation, unprecedented demand for aviation gasoline, and the shortage of rubber for automotive tires. However, these shortages do call our attention to the vital part of petroleum reserves in our country's future position among nations. Therefore, it is of special interest to review briefly the relations of recent supply and demand with respect to our various mineral fuels.

Jan 1, 1943

By S. Agatzini-Leonardou

The objective of this work was to prove repeated loading capacities and investigate the selectivity of physically stabilized algal biomass from Spirulina platensis and Chlorella sp. for the removal and recovery of cobalt, nickel and chromium from laterite heap leach liquors. The testwork was carried out on a bench scale in small glass columns and proved that it was possible to immobilize the biomass on the highly porous surface of pumice stone (kissiris). Nickel and cobalt could be removed from pure aqueous solutions of each metal by the immobilized cyanobacterial biomass. Nickel and also cobalt biosorption was sensitive to the initial solution pH. Cobalt recoveries up to 80% were achieved after 5 loading cycles, from low concentration solutions, at pH 6.0. Nickel removal was complete under the same conditions, whereas chromium sorption was ineffective. Desorption of the metal loaded columns was effected by dilute sulfuric acid. The algal species giving the best adsorption capacities for the metals under consideration was selected for further experimental work with real laterite heap leach solution produced by column leaching. A statistical analysis of all obtained results was conducted using the fraction of metal removed as response. The ratio "mass of metal removed to mass of protein contained in the immobilized cells" was determined as well. The described method might be applicable for recovery of cobalt and nickel from diluted laterite heap leach solutions, such as heap wash waters, or for their removal from waste streams of a hydrometallurgical extraction process.

Jan 1, 1997

By M. Gunter, M. Buzon

"Talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic, and lacking in amphiboles. In southwest Montana, talc formed from hydrothermally altered dolomitic marbles, and is still actively mined. These talc deposits are typically in contact with quartzofeldspathic gneiss and marble. Accessory minerals vary between these rocks and the ore producing body; the identification and characterization of such minerals requires carefully selected analytical methods. Recent litigation and ensuing confusion over the petrology and asbestos content of these deposits challenges the talc mining industry in Montana, and elsewhere in the world. INTRODUCTION Commercial talc has been mined from the deposits in southwest Montana since the 1940s, and by 1956 the region had output 200,000 tons of talc ore (Chidester et al., 1964). Commercial talc refers to rocks containing more than 20% of the mineral talc (McCarthy et al., 2006); the ores from Montana typically contain upwards of 90% talc. This region remains the leading domestic source of talc in the U.S. partly due to the reserves in the area, and partly due to the diagnostic purity of the ore compared to that of other regions, some of which are no longer actively mined. The mineral talc, a sheet silicate, is expressed by the formula Mg3Si4O10(OH)2, and therefore can form in geologic environments that are rich in Mg, Si, O and water. The protolith for the talc deposits in southwest Montana is a dolomitic marble, but other common protoliths include ultramafic igneous, mafic igneous, and siliceous dolomites (McCarthy et al., 2006). Physical properties such as hardness of 1 on Mohs hardness scale, white streak and slippery feel are among some of the reasons why talc is so widely used as fillers in a number of industries. In decreasing order, ceramics, paper, paint, roofing, plastics, rubber, and cosmetics are the leading domestic industries that use talc despite the decreasing trend in U.S. talc use and production since 1994 (Virta, 2015). The purpose of this paper is to describe the mechanism of talc formation in southwest Montana by focusing on talc deposits and surrounding rocks in the Ruby, Greenhorn, and the Gravelly Ranges, and to relate the mechanism of formation to the composition of talc ores. The compositional data show mineral content of selected ores, and the major and trace element content of those minerals, specifically talc. Our electron microprobe (EPMA), powder x-ray diffraction (XRD) and x-ray fluorescence data for samples from five mines in these three ranges provide continued evidence of the purity of these ores despite claims made during recent litigation that these ores contain asbestos. The five mines that we discuss include the Beaverhead, Treasure, Regal, Willow Creek, and Yellowstone Mines (Figure 1.)"

Jan 1, 2016

By J. E. Dooley

Reference mass spectra and analytical correlations for 20 alkylcycloalkyl sulfides and two dicycloalkyl sulfides are presented 'to provide information that will facilitate the identification of sulfur compounds occurring in natural or synthetic mixtures. Reference spectra indicate relative intensities in addition to parent and base peak sensitivities. Analytical correlations establish the ionic species that reflect major fragmentation paths for the com-pounds studied. Specifically, the correlations show that base peaks are formed by several different processes: (1) Cleavage of the bond a to the ring, (2) fragmentation of the alkyl chain, and (3) fragmentation of the ring plus fragment contribution from the alkyl chain. Useful correlations for deter-mining alkyl chain length involve the CnH2+3S+ and CnH2n+1 + ions. CnH2n-2+ and CnH2n-1 S+ ions reveal the number of carbon atoms in the cyclic ring. Other important ionic species are also discussed.

Jan 1, 1970

By E. R. Weltevreden, C. Klauber, C. Vernon

"In this paper a review of the current status in recycling technologies for cathode ray tubes is given for both the glass and phosphors. Particular emphasis is placed on the opportunities for the recovery of the rare earth elements (REE) from the phosphor coatings. This is placed in the market context of alternative virgin sources and some of the advantages and disadvantages for REE waste recovery. Future opportunities are explored and also some experimental detail on a low cost leach system is presented. INTRODUCTIONThe disposal of cathode ray tube (CRT) based colour televisions has accelerated world-wide with the development of high definition flat screen panels. The total number of colour CRT televisions that have been sold in the United States in the mid-20th century is estimated to have been over 2 billion (U.S. Environmental Protection Agency, 2007), with high current rates of disposal. It is estimated that of the 20 million televisions annually discarded, 78% are send to landfill (Nnorom, Osibanjo & Ogwuegbu, 2011). However, this easily accessible item of electronics cannot only be turned into a valuable resource using the right recovery procedures, it can also prevent the substantial environmental contamination arising from improper disposal. In this review we focus on previous and current work performed on the recycling of CRT based televisions. Due to the increasing demand for rare earth metals, the main focus will be on the possibilities and challenges of recycling the fluorescent phosphor powders on the CRT’s panel glass.CATHODE RAY TUBE’S GLASS RECYCLINGConventional cathode ray tubes consist of three main parts, the panel, the funnel and the neck (Figure 1). To produce the different colours on the screen, the inside of the panel is coated with a matrix of hundreds of thousands of small phosphor dots. Each dot is one of three types of coloured phosphors, emitting either red, green or blue light. These emit light when excited by a beam of electrons generated by electron guns located in the neck of the CRT. These beams pass through holes in the shadow mask and excite the phosphor coating on the inside of the panel, to give light of variable RGB composition, see Figure 1."

Jan 1, 2012

In March, the Minister of Mines, Mrs. Judy Erola, released a mineral discussion paper at the annual meeting and convention in Toronto of the Prospectors and Developers Association. Among the mineral objectives discussed was the revitalization of the "junior" mining industry. That industry reportedly has seen its share of total exploration expenditures fall from 50% in 1969 to 10% in 1979. Some sources believe the reason to be the rise of exploration costs and more- restrictive legislation The junior mining industry reportedly was responsible for 40% of all mineral discoveries in the 1969-79 period. CZECHOSLOVAKIA Czechoslovakia expects its capacity for the recovery of gallium metal to increase from 1,650 kilograms to nearly 3,000 kilograms per year by the installation of new recovery equipment at the aluminum plant at Ziar Nad Hronom in Central Slovakia. World production data are not reported, but the United States consumed 8,000 kilograms (estimated) in 1981, of which 5,536 kilograms were imported. Gallium is recovered as a byproduct of the Bayer process for the conversion of bauxite to alumina, and from certain zinc processing wastes. It is used for electronic applications such as light-emitting diodes for visual display panels in calculators, clocks, and other instruments.

Jan 1, 1982

By Brian C. Asbury

Gold-bearing quartz veins with auriferou pyritic wall rock alteration haloes at the Komis deposit near Waddy Lake in northern Saskatchewan occur in fractured Archean intermediate volcanic rock flanking a plutonic felsic intrusion. Three ore zones totalling 1.5 million tonnes grading five g/t gold have resulted from a combination of patterns of high density of fracture-filling quartz veins created by contrasting competencies of four predominant rock types and preferential gold deposition in magnetitebearing andesite host rock. Pre-glacial surface weathering remobilized gold from a nearby pyritized intermediateto- felsic dyke to form the EP Zone with a wide variety of supergene accessory minerals. Much of the EP Zone wa eroded by glacial action to forn1 a highly anomalous gold-bearing till dispersion train which facilitated its di covery.

Jan 1, 1986

By E. J. Ostrowski, P. L. Woolf, J. P. Morris, Norwood B. Melcher

By injecting natural gas through auxiliary tuyeres into the smelting zone of the Bureau of Mines ' experimental blast furnace in January 1959 , the investigators succeeded in reducing the coke consumption by approximately one - third that of the base period . This caused a 30 - percent increase in pig iron production with no increase in wind rate . The maximum gas addition in these experiments was 4,665 cubic feet per ton of metal produced . Sharp reduction in gas consumption occurred when high hot blast and high wind rates were used , although the gas injection rate in percent of air blown remained constant . As the heat energy produced by burning natural gas to carbon monoxide and hydrogen is much less than burning coke to carbon monoxide , greater blast temperatures were required during the test runs . The gases produced from the methane were , however , more effective reductants ; so it was possible to increase the production rate while reducing the total heat requirements per ton of metal produced . During a base period with an all - sinter burden , before introduction of natural gas , a coke rate of 1,484 pounds per net ton of pig iron was attained , using an average blast temperature of 1,518 ° F. Gas was introduced gradually over a two -week period until an average 7 percent of the air blown was reached . During this period , the wind rate was adjusted downward to maintain a constant flow of gas in the bosh . The production rate of the furnace remained relatively constant . The quality of pig iron, however , improved as the sulfur load on the furnace was reduced as a result of the substitution of gas for coke . Blast temperatures were increased during this period from 1,518 ° F. to 1,939 ° F. , when the maximum gas addition was reached .

Jul 1, 1960

By Kym Runge, Fengnian Shi

Este artículo resume los resultados de la investigación realizada en los últimos 10 años sobre conminución por pulsos de alto voltaje (HVP) en la industria minera. En el estudio se adopta un nuevo enfoque mediante el uso de bajos niveles de energía HVP para cambiar la procesabilidad de los minerales y lograr una reducción general en el consumo de energía, así como un mejor rendimiento metalúrgico. El artículo discute los vacíos de conocimiento y las incertidumbres que inhiben la adopción del HVP por parte de la industria minera y hace hincapié en la necesidad de realizar más investigaciones para lograr la siguiente generación de tecnología de conminución.

Nov 30, 2019

By Takashi Sasaoka

About 200 M tons of coal were imported into Japan in 2007 and Indonesia was its second largest exporter, accounting for about 30 M tons (12% of the total imported coal). Indonesia produced about 200 M tons of coal, about 75% of which was exported in 2007. As the Indonesian government has decided on an energy policy wherein 33% of the country?s primary energy demand will be met by coal by the year 2025, the domestic demand for coal has increased dramatically in recent years. Over 99% of the coal produced in Indonesia comes from surface mines. However, the conditions of surface mines are worsening each year: the stripping ratio is increasing, approaching the economic ratio, and the infrastructure for coal from inland mining areas is insufficient for such intense mining operations. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. However, mining engineers and/or miners in Indonesia do not have a lot of experiences, expertise and know-how concerning the plans and operations of an underground coal mine. In addition, the industry faces a lot of problems which include poor conditions such as a steep coal seam, groundwater problem, stability of highwall, etc. Under these situations, a mine targeted in this research attempts to develop a new underground mine from an open-cut highwall because the stripping ratio in the surface mining area has almost reached the limitation of economic value. This paper discusses the possible development of a new underground coal mine from an open-cut highwall by means of field observation and numerical analysis.

Jan 1, 2009

By K. Sarveswara Rao

"Any innovative approach made in non-ferrous metallurgical industry centers upon developing new processes, saving materials, improving production quality, and bornagain materials. Aqueous processing is commonly used to treat lean grade or more complex ore bodies. Its sustenance largely depends on energy and environmental compliance including water and wastewater management. The present paper focuses the importance of using particle size distribution and surface area measurements during ammoniacal dissolution of a Cu-Pb-Zn sulphide bulk concentrate and with an overview of the effect of water salinity on the process chemistry and residue mineralogy. Accordingly, an effort is made here to discuss the emerging perspective and highlight the recent successes and trends in terms of energy savings in non-ferrous hydrometallurgy.IntroductionThe nature and structure of the global energy industry is likely to change significantly in the 21st Century. Rabago et al [1] have comprehensively discussed how the mining and minerals industries can adapt to the challenges and opportunities posed by trends and drivers in global energy use. According to the authors, the drivers of sustainability include water, efficient energy use, climate modification, transportation technologies and energy security. Sustainability and competitiveness for the minerals industry will depend on natural capitalism, resource efficiency, new processes, saving materials, improving production quality, born-again materials and the solutions economy. Based on this motivation, the theme of the present paper is centered upon applications as relevant to energy and sustainable development in non-ferrous hydrometallurgy."

Jan 1, 2009

By Thomas A. Steven

Most mineralized areas in the central San Juan Mountains, Colorado, are associated with the youngest subsidence structures in a large volcanic cauldron complex that formed concurrently with eruption of the surrounding ash-flow field. Two local types have been recognized: (1) fissure-vein deposits along faults characterized by relatively late movement, and (2) hydrothermally altered and mineralized areas associated with postsubsidence Fisher Quartz Latite centers. The first type has provided most production in the past; the potential of the second type has yet to be adequately tested.

Jan 1, 1968