Search Documents

By Yotamu Stephen Rainford Hara, Animesh Jha

The investigation focuses on a low temperature recovery of Cu and Co from a 40 wt% SiO2-(30 wt%Fe,6 wt%Al)2O3-10wt% CaO-7wt%CuO-7wt%CoO slag over a temperature range of 1173K to 1323K. The alloy phases containing Cu-Co and Fe-Co alloy formed via the carbothermic reduction of oxides: MO + C = M + CO(g), where M represents metallic copper, cobalt or iron. In the direct reduction of oxides, the recovery of metallic phase was well below 90% at 1323K, due to the kinetic barrier which was analysed and attributed to oxygen and metal-ion transport in the slag. This barrier was overcome by adding CaSO4 and carbon, which yields a matte (MS) phase via MO + CaSO4 + 4C = MS + CaO + 4CO reaction. Lime thus produced in situ participates in metal oxide/metal sulphide reduction reactions, which are analysed with the help of X-ray powder diffraction, scanning electron microscopy, and thermogravimetric analysis.

Jan 1, 2014

By G. G. Morgis

A reasonably clear and broad definition of occupational disease as originated by the Supreme Court of Ohio is: "A disease contracted in the usual and ordinary course of events which from the common experience of humanity is known to be incident to a particular employment." An ailment does not become an occupational disease simply because it is contracted on the employer's premises. It must be one that is commonly regarded as natural to, inherent in, and concomitant of the work in question. The important distinction between accidental-traumatic injuries and occupational-disease injuries is that accidents occur at specific times, ordinarily are discovered readily, and usually leave no question as to the particular employer it whose development the accident occurred. On the other hand, occupational diseases may develop slowly, unknown to the employer and employee until disability occurs, and the injuries sustained are continuing disabilities over an extended period of time and may be incurred while the employee is working for one of several employers.

Jan 1, 1952

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

By Lassaad Hazzar

The ultimate lateral resistance of piles in cohesive soil is studied using the well-known finite difference code, FLAC2D. The Modified Cam Clay (MCC) constitutive relation is adopted in the analyses to model the cohesive soil behavior, whereas the structural pile model with three degree of freedoms, available in FLAC2D library, is adopted to model the piles. The reliability of Broms's method, still used in the current design practice of piles under lateral loads, is verified. Comparisons between the ultimate lateral resistances of piles and those deduced from the graphs proposed by Broms (1964) are presented in graphs. Different factors thought to affect the lateral resistance of piles in cohesive soil, not adequately considered in Broms's method, such as clay stiffness, pile length, pile diameter and axial load are parametrically studied. A special concern is devoted to elucidate the effects of over-consolidation ratio (OCR) on the ultimate lateral resistance of piles in cohesive soil.

Aug 1, 2013

By Márcia Maria da Silva Monteiro Pereira

Durante o lingotamento contínuo de aço, partículas de ZrO2 adicionadas na escória de molde facilitam a nucleação heterogênea de cristais devido à sua limitada solubilidade. A adição de ZrO2 promove a cristalização da fase cuspidina, o que auxilia na redução da transferência horizontal de calor no molde, amenizando desta forma o problema das trincas longitudinais. Outro benefício da adição de ZrO2 em pós fluxantes é reduzir a taxa de desgaste da válvula submersa (SEN) na interface metal/escória; a erosão da SEN é um problema sério. Através de testes de laboratório e de testes industriais concluiu-se que a adição de ZrO2 em pós fluxantes reduz a taxa de transferência de calor horizontal no molde durante o lingotamento contínuo de aço, considerando os dois tipos de pós fluxantes que foram analisados no presente trabalho. Além disso, observou-se que a adição de ZrO2 reduz a taxa de desgaste da válvula submersa na interface metal/escória.

Aug 16, 2017

By J. E. Urosek

In October, 1990, a fire started in a large underground coal mine in Western Pennsylvania. During fire-fighting activities, an explosion occurred and all personnel were evacuated. Safe re-entry into the mine was not possible and the mine was sealed. Recovery efforts began in January, 1991 and continued until March, 1991, when permanent underground seals were installed between the fire area and the mine openings. This paper describes an extensive atmospheric monitoring program conducted by the Mine Safety and Health Administration (MSHA), Pittsburgh Safety and Health Technology Center (PS&HTC) including the analysis of mine fire gases, natural ventilation, fan pressure and air quantity distribution.

Jan 1, 1993

By W. M. Cross

The use of fillers and reinforcements for plastics has increased considerably over the past few decades. For example, in the 1980's the average growth rate of filler use was 5.8%. [Katz and Milewski, 1987] Similar filler use growth rates occurred in the 1970's due largely to the increase in price of petrochemical starting materials for plastics. While filler use is still sometimes predicated on the cost benefits associated with their addition to the plastic, other mechanical and performance advantages associated with filler addition are being realized, and account for most of the increased usage. Plastic filler types are many and varied, and include both inorganic minerals/metals and organic compounds, with the former type being, by far, the more common. Common mineral fillers include oxides, including both natural and synthetic silica; carbonates, particularly calcium carbonate; clays such as kaolin; and silicates like mica and talc. It has been recognized that a number of factors influence filler performance, including particle size, shape, surface area, and hardness to name a few. In addition, the interaction between the filler and the plastic is of paramount importance as this interaction will determine the wettability, bonding and the adhesion between the two materials, and ultimately, the mechanical properties of the composite. Froth flotation has long been recognized as a viable process to separate different mineral types. [Leja, 1982] Prior to flotation the minerals are liberated from the ore by comminution. The mineral particle size range produced by this comminution process is typically between 300 and 10 microns. This size range is also typical of mineral fillers for plastics. The size similarity between mineral fillers and minerals concentrated by froth flotation is only one of many similarities that can be found.

Jan 1, 1997

By Pedro Cunha Alves

A cada ano a demanda por aços limpos aumenta, tornando o controle de inclusões cada vez mais importante. Durante o refino secundário de aços, ocorrem a eliminação de impurezas, ajuste da composição química e ajuste da temperatura do aço líquido. A remoção de inclusões não-metálicas geralmente ocorre nessa etapa, sendo realizada pela escória. Neste trabalho, foi definido um planejamento de experimentos para que numa segunda etapa, os conhecimentos obtidos possam ser comparados e transferidos para a prática industrial. Inicialmente, foi feita uma revisão da literatura sobre experimentos realizados em fornos de laboratório com amostras de aços e escórias focados na remoção de inclusões. Depois de analisados diferentes arranjos experimentais propostos, alguns trabalhos selecionados foram analisados com respeito às inclusões e às escórias presentes. Finalmente, no planejamento proposto, definiu-se que os experimentos serão realizados em forno resistivo com passagem de argônio. As amostras serão fundidas em cadinhos de MgO na temperatura de 1600ºC e, após 90 minutos nesta temperatura, as mesmas serão resfriadas em água. Alguns parâmetros que poderão ser estudados são a população de inclusões, viscosidade efetiva da escória, teor de oxigênio total e composição de inclusões ao longo do tempo.

Oct 30, 2017

By George J. Karcas

"Non-ferrous metals such as copper, nickel, lead, zinc and precious metals are produced via the electrorefining and electrowinning processes. Apart from controlling electro-chemical conditions for the production of these metals, there has always existed the challenge of controlling the corrosive effect of the electrolyte environment which serves as the medium for non-ferrous metal production.The practice of acid containment in electrometallurgical operations has entered the world of high technology with the advent of advanced acid resistant materials such as vinyl ester resin which is either combined with aggregate to form polymer concrete or used to line various acid containment vessels and ·surfaces. ill comparison to some Asian, European, and African copper refineries, the North and South American copper industry has recently embraced quite heavily in the use of polymer concrete electrolytic cells and process vessels, such as electrolyte storage tanks, and in the use of vinyl ester resin for corrosion protective surface sealing 'systems in lieu of epoxy, acrylic and other materials because of its combination of higher corrosion resistance and superior flexibility.Electrolytic cell construction has undergone a transformation from a multiple part configuration to a single piece moulded/cast unit. ·The one piece moulded polymer concrete cell, which has been patented by Corrosion Technology International, with the overflow, decant, inlet, fast fill and segregation systems integrally designed is now the industry standard.. The combination of a wood, steel, or concrete frame with a lining made of lead, asphalt, rubber or plastic has been historically successful in providing limited protection from chemical and mechanical attack in electrolytic cells and electrolyte storage tanks all over the world. These combinations have now become obsolete as materials such as polymer concrete provide exceptional corrosion and mechanical protection with greatly reduced maintenance requirements and improved efficiency and productivity for the tankhouse. ill addition, polymer concrete can be disposed of in a regular land fIll which is much less costly than disposing of contaminated concrete that is normally associated with conventional lined concrete cells."

Jan 1, 1997

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By Wagner Luís Garcia Silveira

Nos últimos anos a thyssenkrupp Companhia Siderúrgica do Atlântico – CSA tem passado por uma série de mudanças no que diz respeito ao perfil de qualidade das matérias-primas, principalmente em relação à piora de qualidade do minério de ferro extraído do quadrilátero ferrífero em Minas Gerais, o qual compõe 100% da carga metálica utilizada pela CSA. Uma das principais mudanças observadas foi o aumento do teor de fósforo na carga metálica (sinter produto, pelota e granulado), tornando-se necessários estudos para minimizar os impactos na elevação de P no gusa, tais como, desenvolvimento de novos fundentes e aditivos. O fósforo é um elemento que traz poucas alterações nos processos de Metalurgia da Redução (Sinterização, Coqueria e Alto forno) e existem métodos eficazes de redução destas alterações [1], porém é extremamente prejudicial à qualidade, produtividade e custos de uma Aciaria, principalmente em produções de aços que exigem baixo teor de fósforo em sua composição [2]. Este trabalho tem como objetivo apresentar os esforços realizados pela Sinterização em relação à redução do teor de fósforo no Sinter Produto e consequentemente no Gusa, por meio de simulações de qualidade envolvendo novos fundentes e aditivos.

Aug 17, 2017

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994

By B. H. Eccleston

The effect upon automobile emissions in changing from leaded to lead-free gasolines was studied in experiments by the Bureau of Mines in cooperation with the American Petroleum Institute. Typical U.S. leaded gasolines and prototype lead-free gasolines of comparable octane quality were used in eight vehicles operated to simulate city driving. The experiments were run at 70° and 95° F. Exhaust and evaporative emissions were measured and the photochemical effect of the emissions was experimentally observed in an artificial smog chamber. Results of the study reveal the manner and degree in which the changes in fuel composition alter the amount and characteristics of both exhaust and evaporative emissions. Briefly, it is shown that the compositional differences between leaded and prototype lead-free fuels resulted in higher photo-chemical pollution potential of the emissions from the lead-free fuels. The effect is attributed to the photochemical characteristics of high-octane fuel components that are used in greater quantity in the lead-free fuels.

Jan 1, 1970

By F. D. S. Marquis

An investigation of the mechanisms of formation of two types of porosity-primary and secondary-their characterization, evolution during processing, and effects on the mechanical behavior (fracture, fatigue, and failure) of 7X50 and 2X24 alloys has been conducted. The mechanisms of formation of three forms of primary or cast porosity were investigated, and each form was characterized: (a) macroscopic shrinkage porosity-MSP); (b) microscopic interdendritic porosity (MIP); and (c) hydrogen gas porosity (HGP) or primary hydrogen porosity (PHP). The mechanisms of formation of four forms of secondary or thermal/thermomechanical porosity were investigated, and each form of porosity was characterized: (a) high temperature oxidation (HTO). internal hydrogen precipitation (IHP), or secondary hydrogen precipitation (SHP); (b) preheating blistering porosity (PBP); (c) eutectic melting porosity (EMP);and, (d) dissolution micro void formation (DMF). The evolution and interactions of the primary and secondary types of porosity (w.ith special emphasis on PHP and SHP) during industrial and laboratory processing and their effects on the fracture and failure behavior of both types of alloys (with special focus on fatigue crack initiation and propagation) were investigated.

Jan 1, 1996

By A. Bahrami

Andalusite, silimanite and kyanite are polymorphs of aluminosilicate known as kyanite group. Minerals of this group are used in refractory. Sarband andalusite deposit is located in Markazi province in Iran. Mineralogical studies showed that the main minerals of this sample are andalusite (5%~10 %), mica, quartz and feldspar. Processing of the samples was carried out using two sizes, i.e. +500 µm and -500 µm. In the processing of +500 µm scrabble test was carried out on -4750 +500 µm and -2380 +500 µm. For -500+300 µm shaking table and magnetic separation were applied. For -300 µm fraction, flotation was carried out. The results of this tests showed that the processing of Shazand andalusite was not possible, because silica and iron impurities were diffused inside the andalusite mineral grains.

Jan 1, 2014

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By R. E. Heithecker

Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalk-rock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I. Although the field is divided into several districts which are more or less clearly defined and separated by unproved territory the term Zwolle field", as used in this report, includes the entire area from Blue Lake on the west side, through Zwolle proper, and eastward, including the Many or Eastern extension.

Jan 1, 1934

By H. A. Dierks, H. B. Link

The purpose of this investigation was to develop a practical feeder apparatus to introduce comparatively large pieces of coal and similar material into a pipeline under pressure in connection with the vertical hydraulic transportation of solids , termed " hydraulic hoisting . " This method of hoisting the precrushed run - of - mine product of an underground mine has been given unusually wide attention abroad and could be of considerable significance to the U.S. mining industry in its search for operating improvements and cost reduction . A lock-hopper assembly was developed after a series of sinking velocity tests were made by dropping anthracite in a column of water . The system functioned reliably as an automatically operated feeder apparatus .

Jan 1, 1964

By D. N. Nilsen

A mathematical modeling method was developed by the Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of copper. The use of models for predicting the amount of metal extracted can reduce the amount of experimental work required to characterize a system for purposes such as optimization studies. Models were developed for the extraction of copper from ammoniacal sulfate and carbonate solutions with commercially available extract ants commonly used by industry. Results from laboratory shakeout tests compared well with predictions of the equilibrium concentrations of copper and pH values. For example, the loading of copper onto the solvent was predicted for most cases within ±S pct of the measured values, and the pH to with-in ±O.l pH unit in sulfate systems and ±O.2 pH unit in carbonate systems. Both mechanistic and empirical extraction equations were developed from laboratory data for copper and ammonia. The empirical-based models were slightly more accurate than were the mechanistic-based mod-els. Industrial level concentrations of the aqueous and organic constituents were used in this work. Independent variables included copper concentration, ionic strength, and initial pH of the aqueous phase; extractants, diluents, and their concentration in the organic phase; and temperature.

Jan 1, 1988