Search Documents

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects. Both specimens were constructed with pile diameters of d = 0.61m (2 ft), fixed head boundary conditions, and placed in stiff clayey soil at a test site near the LAX Airport in Southern California. Internal instrumentation was installed in the single pile as well as in three piles within the pile group to obtain pile curvatures. External instrumentation controlled the lateral displacement of the specimens. A combination of experimentally and analytically obtained p-y curves for the single pile was used to simulate results for piles located in the group when field data were not available. All test specimens were tested to structural failure and excavated after test completion to investigate pile damage and plastic hinge formations. Calculated group interaction factors ranged between 1.0 at very small displacement levels of <2.5 mm (0.1 in), 0.8 at the initiation of the pile-soil-pile interaction, i.e. between 4 mm - 15 mm (0.16-0.6 in), and increased towards 0.9 near structural failure (displacement >25 mm or 1 in). A literature set of p-multipliers was found to reproduce an accurate fit to the available load displacement test data from the group.

Jan 1, 2010

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

The Karangahake gold-silver deposit is located 11 km west of Waihi in the southern part of the Hauraki Goldfield. Historically it was the second largest bullion producer in the goldfield with a past production (1882 - 1944) of 126.712 tonnes of gold-silver bullion (Au:Ag ratio of 1:3.3) from 1 142 315 tonnes of ore grading 27.4 g/tonne gold equivalents.

Jan 1, 1987

By A van Jaarsveld

Environmentally-friendly, safe and cost-effective technology for stope drilling has successfully been introduced at TauTona mine. It has enabled the problem of inadequate compressed air pressure and its downgrading impact on production capability to be overcome. The paper traces the development process which culminated in the conversion of the entire stoping operation at TauTona to electric drilling. Background work which took place at other mines is also described. Statistics of performance improvements are provided. 1. Introduction Holman?s Silver series and the Seco S215 were drills that had a measurable impact on the South African gold mining industry. It is too soon to say whether Hilti will join those great names. However, there is no doubt that the introduction of electric drills into the harsh and unforgiving world of deep level gold mining is a significant development. History has shown that being the first to enter a new technology is no guarantee of long-term success. The pain and suffering which accompany the birth of anything new can deplete the energy of the innovator while at the same time creating opportunities for competitors to leapfrog him. In addition to commitment and enthusiasm, the innovator must therefore also possess, or have access to stamina and resourcefulness to overcome the unexpected difficulties which will inevitably arise. All of these were needed for the Hilti project.

Jan 1, 2008

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By K. Kawakami

In Japan, pile foundations have been used extensively for buildings, bridges and port facilities. A large number of steel pipe piles were first used in the 1960&apos;s and the amount of steel used in foundations increased by 1973 to one million tons. This report describes current practice in the actual use of large diameter and long steel pipe piles in Japan, related to their performance: including consideration of pile size, hammer types used for driving the results of field tests measuring stress occurring in the piles and the driving formulae currently being used in practice in Japan.

Jan 1, 2010

By D G. Randall, R Jivanji, J Nathoo, T Reddy

Paradoxically, the increased emphasis on water treatment in mining has generated a new problem û hypersaline brines. Currently brines are either disposed of into ash systems, lined evaporation ponds or hazardous waste sites. Evaporative crystallisation (EC) is an alternative, but the energy requirements can be prohibitive and the salt product is still a waste that must be disposed of. Eutectic freeze crystallisation (EFC) is an alternative technology that is capable of separating aqueous solutions into pure water (as ice) and pure, solidified solutes. It is highly energy efficient and does not depend on the introduction of any solvents. In addition, the simultaneous production of pure ice and potentially saleable pure salt(s) is a major advantage. Although EFC has been shown to be effective in separating a single salt and water, it is still in the early stages of being applied to the multi-component hypersaline brines that are typical of reverse osmosis retentates generated by mining and extractive metallurgy.This paper presents an EFC brine treatment protocol developed by the Crystallisation and Precipitation Unit at the University of Cape Town. The protocol incorporates brine analysis, thermodynamic modelling to establish which salts will freeze out and at which temperatures, followed by experimental studies to determine the kinetic parameters, such as nucleation temperatures, salt yields and crystal purity.Case studies showing the application of EFC for the purification of typical brines containing high levels of sodium, chlorine, sulfate and ammonia (Brine 1) and a mixture of sodium and magnesium sulfate (Brine 2) are covered. Modelling tools were applied to describe the phase behaviour of the multi-component saline systems under different process conditions. Experimental validation was carried out using synthetic brines of different (and increasingly complex) compositions. The results showed that EFC could be used to selectively recover the sodium as a sodium sulfate salt from both different brines. The simulation tools were useful in the analysis and understanding of the process.A preliminary economic analysis showed that the operating costs for EC were approximately nine times those for EFC, but the capital costs were much less- equipment for EC cost about half that of EFC. However, it is important to note that the capital cost calculations for EC are based on a technology that is already well established and with only relatively marginal future equipment cost savings expected. In contrast, EFC is a new technology, with significant future technology improvements expected.

Jan 1, 2009

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By Edward L. Tullis

Numerous widely distributed pegmatites of the southern Black Hills of South Dakota contain small amounts of beryl, and two minor deposits are known in the northern Black Hills. Few mines have produced more than 50 tons, and the current, rate of production for the area is about 100 tons annually. Total production, since the first records, is 2,358 tons. Most of the deposits contain less than 1 percent beryl, although the beryl zones in several deposits contain 2 percent beryl or more. Estimated reserves of beryl total 11,824 tons, and an additional 234 tons has been measured; there are other unestimated reserves. The pegmatites are in a belt about the margin of the Harney Peak batholith in the southern Black Hills, although they fail into three districts. The most important, from the point of view of production and reserves, is the Keystone district. Many deposits also are found in the vicinity of Custer and Pringle. Small amounts of beryl occur in the dikes near Hill City. A little beryl has been produced from the Tinton district in the northern Black Hills, and an undeveloped dike has been discovered on Whitewood Peak near Deadwood. The beryl-bearing pegmatites are principally coarse-grained intergrowths or massive segregations of feldspar, quartz, and mica. Some of them contain notable amounts of lithium minerals, as well as some tantalite, columbite, and cassiterite.

Jan 1, 1952

By Hongyang Cao

The iron constituents selectively separated from the modified copper slags by magnetic separation and flotation.were studied. The results of magnetic separation for modified copper smelting slags show that the grinding size, current intensity and dispersant agent had great influence on grade, and recovery ratio of TFe in preparation concentrate; The results of flotation for magnetic concentrate show that the positive flotation of sodium oleate negatively upgrade the grade of magnetic concentrate, but the reverse flotation of lauryl amine and soluble starch are effective. The grade of TFe can reach 54% and the recovery ratio can reach about 90% in magnetic concentrate, when the grinding size is 45.8µm and the current intensity is 2.5A. The optimal effect is obtained by using lauryl amine as collector and soluble starch as depressant to reverse flotate magnetic concentrate, and the grade of TFe is upgraded 2.37%.

Jan 1, 2009

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

Editor?s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice-chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor. Rajesh Raitani, member SME, of Cytec Industries Inc., is chair of the Industrial Minerals and Aggregates Division?s Technical Committee. The technical Committee vice chairs include: ? Vishal Gupta, member SME, of FlSmidth, Agricultural Materials. ? Candace Trimble, member SME, of Oil- Dri Corporation of America, and Bradley Van Gosen, of the U.S. Geological Survey, ceramics and refractory materials. ? Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials. ? Russell Winn, member SME, of R.E. James Gravel Co., chemical raw materials. ? Justin Zdunczyk, member SME, of Plum Creek, construction materials. ? Jerry Gauntt, member SME, of Golder Associates, fillers and pigments. ? Michael Cheshire, member SME, of Los Alamos National Laboratory, sorbents, filters and process aids. ? Rajesh Raitani, member SME, of Cytec, Industries Inc., specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jul 1, 2013

A homely simile will serve to epitomise an interpretation of the rock structures and associated phenomena of the block of country under review, as it appears to the writer.Disregarding the many thousands of feet of overburden that have been eroded away during the ages, the present denuded surface and rock systems below may be pictured as a slab of some titanie ribbon cake that has suffered much damage from rough handling and exposure, yet retaining much of the original symmetry of its superimposed layers of variegated colour and texture.Lateral pressure has crumpled the cake into a series of irregular corrugations and, in parts, has caused some of the layers to crush and slide over their neighbours.Following upon this squeeze, the cake has been severed into segments and rhomboidal slabs by vertical cuts, and these portions have been severely jostled one against its neighbour, crushing the faces of contact and dragging the contiguous layers in the direction of movement.The variegated icing of the cake is represented by intercalated sills of amphibolite, pegmatite, and aplite, and the body of the cake by highly altered sedimentary rocks.The icing has been assailed by the rats of erosion with such effect that only residuals of the original structures remain. The body of the cake has suffered successive waves of igneous invasion in the order of lode pegmatite, followed by zine, iron,copper, and finally by silver-lead. These successive invaders found difficult access, along certain of the vertical cuts, to the more succulent layers of the cake, where, gorging to repletion, many were imprisoned and entombed for the future service of mankind.

Jan 1, 1927

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the coal mining industry. This course is intended for training those, usually the safety officers, who perform surveys fur inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Coal Mining and Processing Work Areas? (NTIS #PB-243-35";) is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 1976

By B Orchard

New Zealand SteelÆs Waikato North Head mine, situated at the mouth of the Waikato River, supplies approximately 1.2 million tonnes per annum of titanomagnetite concentrate to the Glenbrook steel mill. The mine draws its fresh water supply from the Waikato River, abstracting approximately 38 000 cubic metres per day. During the concentration process of the ironsand, slimes are liberated into the plant wastewater. The plant wastewater, storm water and groundwater from the mining operation is treated and passed through settling ponds. Around 118 400 cubic metres per day of water are drawn from the recycle settling ponds for use in the concentration plant. Typically a daily average of up to 15 100 cubic metres of the treated water is discharged back to the Waikato River. Since the early 1990s significant improvements have been made to the water treatment at Waikato North Head mine and regularly the mine discharge water quality is similar or better than background river water quality.

Jan 1, 2002

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

By J Fut=

The rotary drilling of rocks is widespread technology in mining and in tunnelling. The paper describes the results of research by aim to find relationships between optimal drilling and sound signal of drilling machine. The optimisation criterion has been formulated as the minimisation of specific energy with maximal effective speed of drilling in process of the rock disintegration. The research in this field has been made on experimental drilling stand. Our monitoring system has measured following variables: the pressing force of core drill, the revolutions of drilling head, the length of drilling, the time, the power, and the acoustic signals. For measurement of acoustic signals have been used very sensitively sound meter MEDIATOR 2238. From this measurements have been processed acoustic spectrums. Then we are found relationships between optimal control of drilling and composition of acoustic spectrum. On base of experimental results, we can formulate the optimal control following: æTo achieve the minimum difference between the equivalent sound level at the load and idle modes only at the representative frequency (f = 1000 Hz)Æ. The representative frequency dependences on type of the rock New method based on these relationships enables the optimal control of drilling machine by using measured acoustic signals only.

Jan 1, 2003

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003