Search Documents

By S. Chama, K. Nyirenda, J. Machona, P. W. Chishimba, S. Parirenyatwa, G. Kaluba, Y. R. S. Hara, D. M. Musowoya

Our study focuses on upgrading of copper and cobalt from the Democratic Republic of Congo tailings, containing 2 wt% Cu and 0.5 wt% Co. Cobalt is in the complex iron silicate matrix such that its recovery by direct leaching is not possible. Two concentrating methods were employed in order to obtain copper and cobalt concentrates. Copper was concentrated via flotation and, at the optimal conditions its grade in the concentrate was 31.9 wt%. Cobalt was concentrated to 8.6 wt% b ycarbothermically reducing the flotation tailings with coal in a temperature range of 800–1050 °C and followed by magnetic separation. The reaction products were analysed by atomic absorption spectrometer (AAS) and scanning electron microscopy (SEM) techniques. The best carbothermic reduction temperature was found to be 950 °C due to maximum metallisation and less sintering between gangue and metallic/alloy phases.

Mar 1, 2017

By A. P. Page, G. E. Alexander, L. L. Sirois, A. A. Winer

A knowledge of the electrical surface characteristics of minerals is all-important in the choice of treatments to up-grade and beneficiate them. At their solid-liquid contacts, there are transfers of ionic species, which for insoluble oxide minerals are the H+ and OH-ions. The adsorption density of these ions can be detected by carrying out potentiometric titrations, and this paper describes the automation of such an apparatus. The details are discussed fully and the validity of the method is demonstrated by flotation tests.

Jan 1, 1969

By Iván Ibañez

An essential aspect of energy efficiency is determining the opportunities to improve a system or machine's performance from the energetic point of view. For the mining industry, it's a classic problem that mainly all the equipment manufacturers face today to produce the same results with the minimum energy requirements. Existing research focuses on light-duty vehicle energy losses. However, heavy-duty off-road machinery is understudied. This article presents an energy balance assessment of a mining vehicle utilized in an open-pit mine in Colombia.

Sep 29, 2023

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By Diniz Ramos de Lima Júnior

Dentro das refinarias os tanques de armazenamento desempenham um papel fundamental, pois armazenam matéria prima para abastecimento das unidades, produtos intermediários entre os processos e produtos finais para distribuição. O presente trabalho apresenta de modo comparativo as características mecânicas e microestruturais da zona termicamente afetada de juntas soldadas formadas pelos processos de soldagem com Arame Tubular (FCAW) e Eletrodo Revestido (SMAW) aplicados na fabricação e reparo de tanques de armazenamento utilizados na indústria de petróleo. Os procedimentos de soldagem para cada junta soldada seguiram EPS (Especificação do Procedimento de Soldagem) utilizada por uma empresa que fabrica e repara tanques de armazenamento para indústrias de petróleo. O metal de base utilizado foi o aço estrutural de classificação ASTM A-36 em geometria plana e com chanfro tipo K. A solda foi multipasses de topo na posição horizontal (2G). Para realização deste estudo foram realizados quatro tipos de ensaios destrutivos: tração, microdureza Vickers, impacto Charpy e metalográfia. Os resultados indicaram a importância da seleção do processo de soldagem em termos de produção e formação da junta soldada e uma heterogeneidade devido as diferentes microestruturas presentes nas zonas termicamente afetadas que demostraram grande influência no perfil de microdureza.

Aug 8, 2018

By Seth H. Hamblin, John E. Regan, Dimitrios Palantzas

"Through reliability-based calibration of larger pile load test databases, recent developments of the Load Resistance Factor Design (LRFD) methods, which include geotechnical load and resistance factors for deep foundations design, have advanced the state of practice for geotechnical engineering. These load test databases upon which the current geotechnical load and resistance factors have been developed are limited, however, and do not provide sufficient data to support the development of resistance factors for uplift (tension) pile capacity. As such, some recommended resistance factors for uplift capacity estimation methods are simply derived by reducing the recommended resistance factors for piles in compression by a factor of 0.10.The results of three (3) tension loading tests performed to failure on 508 mm (20- in) square precast, prestressed concrete piles, driven though granular soil in southeastern Massachusetts, are presented and compared to static pile capacity calculations and dynamic analyses performed using the Pile Driving Analyzer (PDA) during installation. These results are presented along with current recommended LRFD resistance factors for driven piles under uplift (tension) loading conditions. These comparisons offer an assessment of the applicability and limitations of current resistance factors methods for piles under uplift loading and may be useful additions to the existing database for future calibrations of LRFD resistance factors for driven prestressed concrete piles in sand.IntroductionIn 2010, two (2) natural draft cooling towers were constructed by Kiewit (Kiewit) Construction Company of Woodcliff Lake, New Jersey at the Brayton Point Power Station in Somerset, Massachusetts. These massive 500 foot tall, 400 foot diameter cooling towers were designed to convert the existing “open loop” system into a “closed loop system” thereby dramatically reducing the thermal impact to Mt. Hope Bay.Based on design guidance from the German VBG Design Code and the Massachusetts State Building Code (MSBC), tension (i.e. uplift) and lateral loads due to wind loads and design seismic events represented the critical loading conditions.Weighing approximately 190,000 kips upon completion, the cooling tower loads are transferred to 44 foundation nodes (i.e. pile caps) evenly spaced along ring beams which run the circular perimeter of each tower base. Each pile cap node was designed to resist a 2,000 ton compression load, 200 tons in tension (i.e. uplift), and 600 tons in the lateral direction."

Jan 1, 2015

By E. H. Illsley

This bibliography is the first report of a Bureau of Mines research project on thermoelectric materials. Interest in such research has increased because of recent success in the design of commercial products, including generators and refrigerators, using the principles of thermoelectricity. This success made possible by the discovery of semiconductors that have much higher [effincies] than the metals and alloys formerly studied. Thermoelectricity is a term that includes a large number of phenomena relating heat to electrical energy. However, the moat important applications arise from two effects discovered by Seebeck in 1822 and by Peltier in 1834. When pieces of two unlike materials are joined at their two ends to form a continuous circuit, both of these effects may be observed. If the two junctions are maintained at different temperatures, an electromotive force known as the Seebeck voltage is generated. If, on the other hand, a current is made to flow through the circuit, the junctions of the materials will be found to differ in temperature. This phenomenon is called the Peltier effect.

Jan 1, 1959

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By W. S. Kirk

World cobalt production in 1987 was estimated to be about 26,600 metric tons (MT) of which Market Economy Country (MEC) production was estimated to be about 22,000 MT. Zaire and Zambia produce about 80 percent of the primary cobalt produced among Market Economy Countries (MEC). Production cutbacks. lowering cobalt grades and mining curtailments in Finland and Zambia in 1987, resulted in lower production than that of 1986. The trend is expected to continue through 1988. Cobalt production from Canadian ores and from Botswana is expected to increase significantly in 1988 as a result of increased nickel production. MEC production in 1988 is estimated to be 22,100 MT, only slightly higher than that of 1987. There are currently no primary cobalt mines. Virtually all cobalt is recovered as a byproduct of copper and/or nickel mining. Zaire, which produces cobalt as a byproduct of copper, is the worlds largest cobalt producer, with over 50 percent of total estimated world cobalt production and nearly 65 percent of MEC production. Zambia follows with about 14 percent and 17 percent, respectively. Zambia's cobalt production also results from copper production.

Jan 1, 1988

By W. W. McClintock

A column flotation system was designed to conduct release analyses of a very finely disseminated, stratiform, copper ore from the Denali Copper Prospect, Alaska. Chalcopyrite is finely disseminated in a carbonate matrix and pyrite is disseminated in both the chalcopyrite and gangue, requiring grinding to 20 microns for adequate liberation. A 25 mm x 2.4 m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate, which was repeatedly floated to produce release fractions. These were analyzed for copper, iron calcium and magnesium. Release curves were plotted. The procedure was replicated at each of two grinds; 99% and 88% passing 37 microns (400 mesh), and should find application for flotation characterization and process selection. Bond grindability work was also conducted.

Jan 1, 1994

By Ushakov S

New geological and geophysical in vestigation including our detailed field observation in different regions of the Koryak upland testify that Nor- theastern Eurasia margin eastward of the Ochotsk-Chukotka belt is composed of a collage of allochtonous terranes arcs and sedimentary filling of back- arc basins, which bordered North East Siberia and Chukotka (1)1). Ancient island are assemblages are the most tipical for this region (2-4; shown by heavy line). They are marked by long (500-1000 km) volcanic belts which become younger towards the Pacific up the Latest Jurassic-Neocomi- an (2) to Late Cretaceous (3) and Pale- Gene (4).

Jan 1, 1987

By J. E. Wilson

The Pittsburgh carbonization laboratory of the Bureau of Mines has determined the expansion or contraction of more than 300 coking coals in a modified Bethlehem-type sole-heated expansion tester. Information on the actions of coals or blends of coals when coked is extremely valuable to operators of commercial-scale coke ovens. Coals that expand abnormally or beyond expectations can cause extensive damage to coke ovens and result in costly shutdowns and repairs. Although test results for many of the coals have been given in various Bureau of Mines publications, considerable information was not published. Thus, it is the purpose of this report to furnish coal operators and the coking industry with a current appraisal of the expanding properties of all coals tested by the Bureau before September 1, 1958. These data should be useful in the normal long range planning of coal and coke production and will be essential if the demand for coking coals increases abnormally or when reserves of higher grade coals are depleted.

Jan 1, 1959

By Harold M. Smith

Among the more important raw materials now utilized for the commercial production of synthetic organic chemicals is natural 'gas. Natural gas has been used as a fuel and source of energy almost from its discovery, but its potentialities as a chemical raw material were not realized until recently. Research in the use of natural gas for Chemical synthesis received great impetus from the discovery by Brooks and Humphrey4/ in 1918 of alcohols in the diluted ?acid oil? obtained by sulfuric acid treatment of cracked petroleum distillates. Experimental data soon showed that hydrocarbons from natural gas could be converted to these same products. Laboratory methods for chlorination of natural-gas hydrocarbons, particularly of methane for the production of methyl chloride, methylene chloride, carbon tetrachloride, and chleroform were known before that time but were not developed commercially. Methods for obtaining alcohol by oxidation of hydrocarbons derived from natural gas also were known before 1918 but had not received commercial consideration. Since 1918, and particularly during the past 15 years, the work of chemists and chemical manufacturers throughout the world has resulted in an accumulation of data regarding the reactivity of natural-gas hydrocarbons, and related hydrocarbons found in refinery gases or made synthetically. These data have been used to develop methods for converting hydrocarbons into chemical products and thus form the basis for a large and growing industry.

Jan 1, 1947

By William G. Pariseau, Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"This contribution describes development and application of a user-friendly finite element program, UT3PC, to address three important problems in underground coal mine design: (1) safety of main entries, (2) barrier pillar size needed for entry protection, and (3) safety of bleeder entries during the advance of an adjacent longwall panel. While the finite element method is by far the most popular engineering design tool of the digital age, widespread use by the mining community has been impeded by the relatively high cost of and the need for lengthy specialized training in numerical methods. Implementation of UT3PC overcomes these impediments in three easy steps: First, a material properties file is prepared for the considered site. Next, mesh generation is automatic through an interactive process. A third and last step is simply execution of the program. Examples using data from several western coal mines illustrate the ease of using the application for analysis of main entries, barrier pillars, and bleeder entry safety.INTRODUCTIONRational design of safe underground entries and crosscuts, barrier pillars, and bleeder entries begins with a site-specific analysis of stress. An analysis of stress identifies the critical regions of high-stress concentration where yielding is likely and additional or more focused ground control measures are needed. This analysis also identifies regions where stress concentration is low, and risk mitigation is less urgent. Displacements induced by mining, including roof sag, floor heave, and pillar squeeze, are also of importance to stability. The popular finite element method is well-suited for such analysis and has been in use for studying coal mine engineering problems since the late 1960s (Dahl, 1969). The method has been taught in undergraduate engineering curricula for many years and offers an alternative to existing design procedures based mostly on rules of thumb, empirical methods based on mine data, and predigital-age concepts of strata mechanics. However, despite the versatility of the finite element method, usage has been limited, mainly because of the cost of the software and the required training in numerical methods.The program UT3PC (Pariseau, 2017) has evolved from early two-dimensional versions in the era of mainframe computers. These early versions were still quite limited using only a few hundred elements that required overnight turnaround times. Recent versions of UT3PC are convenient and efficient desktop programs that use several million elements. With the advent of personal computers in the mid-1980s and subsequent increase in computer speed, expanded memory, and lower costs, applications for mining increased in three-way cooperative projects among industry, the former U.S. Bureau of Mines, and academia. The Spokane Research Center of the U.S. Bureau of Mines, in cooperation with the University of Utah, developed a two-dimensional desktop finite element program, UT2PC, available to the mining community in 1991. This was a short course offered at the 1991 SME Annual Meeting in Denver, CO."

Jan 1, 2017

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999

By S. L. Bessinger

Introduction In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Head losses in mine entries are calculated using Atkinson's Equation. [22H= KPLQ (English) H= KP 3Q (SO (1) 5.2AA] where H = pressure loss, in. of H2O (Pa); K = friction factor, lbf•min2/ft4 (kg/m3); P = perimeter, ft (m); L = airway length, ft (m); Q = airflow quantity, ft3/min (m3/sec); and A = flow cross-sectional area, ft2 (m2) In this equation, the friction factor, K, is an empirical constant that describes the aerodynamic roughness of the airway. Typically, the K-factor for a given airway is determined by measuring the factors H, P, L, Q and A in Equation (1) and calculating K. Tables of friction factors calculated in this way are found in textbooks and handbooks that deal with mine ventilation analysis. Unfortunately, very few K-factors have been measured on longwall faces, and the accuracies of those that have been measured are entirely site specific, because of the wide variety of equipment found on longwalls. The development of a technique for prediction without mine-site measurements of the friction factor for any longwall face, regardless of its configuration, will thus be very useful in the design of ventilation systems for mines in which longwall mining is practiced. Calculation of pressure losses using Atkinson's Equation (1) and empirically determined K-factors provides accurate and useful approximations in cases where the airways have relatively simple cross sections. However, a careful analysis using the principles of fluid mechanics shows that such calculations are based on two assumptions that are not strictly correct when there are obstructions in the airway. The first assumption is that the air velocity distribution in the cross section, particularly around the perimeter, is uniform. This assumption results from the fact that the tabulated K-factor values found in the literature are based on field measurements with uniform conditions. Such uniformity does not exist in longwall airflows. The second common assumption is that the K-factor, and corresponding head loss, is independent of the Reynolds Number (NR) for a given flow. In fact, this assumption is not strictly correct, and is particularly erroneous in the case of irregular protuberances into the airflow, such as those found on a longwall face. The errors arising from the assumptions may be avoided by using K-factors calculated by a newly devised method, described below, which takes into account the fundamental principles of aerodynamic drag analysis. This new technique has two advantages: first, it is flexible enough to model any longwall, regardless of equipment configuration; second, it employs terminology and equations familiar to those who perform mine ventilation analysis, using K-factors, for which ventilation engineers have an intuitive understanding, rather than drag coefficients. To provide guidance for development of a longwall drag model, data were taken on two modern longwalls operating in substantially different conditions. Pressure measurements at Mine B were made with 200-foot (61-m) sections of 1/8-in. (3-mm) diameter plastic tubing, attached to a Dwyer Magnehelic gauge. Pressure drops were measured in 200-foot increments down the face, and summed to give the drop for the entire face length. This technique was found to produce small, repeated errors because of the number of segments required to span the longwall. At Mine A this problem was avoided by using a single, continuous, plastic tube for the entire face length. The psychrometric properties of the air were measured for both Mines A and B. A calibrated, standard vane-anemometer was used to measure the airflow on both faces. Finally, numerous dimensions were measured on both faces, and face profile drawings were obtained to allow detailed evaluation of the face equipment geometry. From this information, accurate evaluations of the average wetted perimeter and average area of the longwall face airways were made. Since the airflow is not confined to inside the powered supports at all points along the face, a quadratically weighted average of the airflows measured at various stations along the face was calculated: [n2Qavg =Qi Ii / It(2)i=1] where [Q, avg = average airflow for analytical purposes, ft3/min (m3/sec); Q= airflow at station i, ft3/min (m3/sec); 1= length of segment represented by Q, ft (m); h= length of longwall face, ft (m): and n= number of quantity measurement stations.] The quadratic weighting scheme was chosen because the

Jan 1, 1992

The Yanacocha district hosts the largest and most significant acid-sulphate, high-sulphidation deposits in Per· with total production, reserves and resources of over 27 million ounces of gold. Several other smaller high-sulphidation systems are also recognised in the Cajamarca region including La Zanja, Sipßn, Tantahuatay, and San Nicolas. These each have reserves/resources of between 640 000 and 800 000 ounces of gold. Gold deposits in the Yanacocha district are hosted in an extensive volcanic field. Flow domes have intruded precursor pyroclastic rocks and flows that are interpreted as part of an earlier intermediate multi-vent volcanic complex. The larger, contiguous Yanacocha Norte - Sur and Encajon gold deposits are spatially associated with late-stage diatreme breccias. At La Zanja extensive acid-sulphate alteration is associated with the margins of the small San Pedro caldera (6 +4.5 km), nested within the larger, less well-defined La Zanja caldera (19 +24 km). The inner caldera is resurgent with abundant magmatism expressed as several flow dome complexes located on the caldera rim, and shallow level intrusive stocks. Gold mineralisation is associated with a WNW-trending structural corridor that transects the southern margin of the San Pedro caldera. On the eastern side of the La Zanja caldera there are a series of younger andesitic eruptive centres, some associated with acid-sulphate alteration and gold mineralisation. The Sipßn deposit occurs in one such centre with structurally-controlled gold associated with a NE-trending silicified structure developed within a sequence of andesitic tuffs. In conclusion, although a number of high-sulphidation deposits are recognised in northern Per·, their settings and styles of mineralisation are all quite different. Smaller deposits generally have strong and obvious structural controls. In the larger Yanacocha deposits the structural controls are less obvious, and mineralisation is disseminated in porous or strongly fractured and brecciated silica. Erosional levels are probably a significant factor, with disseminated mineralisation at higher levels, and structurally-controlled mineralisation in more deeply eroded deposits.

Jan 1, 1999

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models. INTRODUCTION There are many definitions of virtual reality (VR) that include various levels of immersion and features [1]. Some definitions refer to specific technologies [2], while others are limited to visualization [3]. For this paper, a more general definition of VR will be adopted. VR is defined as the collection of hardware and software that interactively engages users and stimulates their senses within a synthetic or virtual environment. From a hardware standpoint, this can include anything from a phone to a head-mounted display (HMD) to a large-scale theater as well as speakers, microphones, haptic sensors, and interaction devices. The software used to create virtual environments (VEs) generally includes a game engine, custom software components and libraries, and two-dimensional and three-dimensional graphical assets. Recent hardware and software advances have increased the fidelity and availability of VR. New and improved technologies including HMDs and high-resolution monitors and projectors can display sharper, more detailed visualizations. For example, in the past five years between the release of the Oculus Rift DK1 (2013) and the HTC Vive Pro (2018), there was a three-fold increase in resolution along with a 50% increase in the refresh rate. Furthermore, despite early claims that low-cost VR technology was readily available [4], computational power has not been sufficient to handle the large amount of data generated by these systems [5]. In the past five years, however, rendering speeds have more than doubled and memory has more than tripled [6], allowing these visualizations to be incorporated into higher-complexity and -fidelity VEs that more closely mirror the real world. Similarly, software capabilities have also significantly improved through game engine advancements and feature development. In the past several years, game engines have added and improved features such as physics, lighting, platform support (e.g. Android), and asset development integration. Some of the current leading commercial game engines are Amazon Lumberyard, CryEngine, Unreal, and Unity, but this can quickly change as is evident in the literature [7, 8].

Jan 1, 2019

By Enrique Pasquel Carbajal

El presente texto describe los resultados realizados por el Centro de Investigación tecnológica del Cemento y del Concreto (CIDETEC) sobre el empleo de microalfiler de carbonato de calcio como adición mineral para mejorar las propiedades reológicas en estado fresco y endurecido del shockrete empleado en las labores de sostenimiento en la industria minera. Asimismo, se señalan la aplicación de esta tecnologías en proyectos mineros como Cobriza, Andaychagua, San Cristobal y Pallancata.

Sep 12, 2011