Search Documents

By Delphine Pierre, Jean-Marie Augustin, Anne-Sophie Alix, Charline Guérin, Cecile Cathalot, Yves Fouquet, Arnaud Gaillot, Ewan Pelleter, Carla Scalabrin, Florian Besson

With the world’s growing demand for metals, seafloor massive sulfides (SMS) deposits are now seen as a possible mineral resource that could contributes to secure metal supply for human needs. SMS deposits are characterized by high concentrations of base metals and at some place high contents of precious and rare metals. Since 1977 and the discovery of the first high temperature (HT) hydrothermal vent and its sulfide mineralization and high biodiversity, more than 300 sites are known today. If the exploration strategy for detection of active hydrothermal sites is now robust, their associated mineralization will not (and must not) constitute a potential target for deep-sea mining due to environmental concerns and technical limitations. Recent studies on SMS deposits are rather focused on extinct and buried mineralized sites characterized by a lower biomass. Several geophysical techniques to explore and detect extinct SMS (eSMS) and buried SMS (bSMS) have been developed (e.g. Kawada and Kasaya, 2017; Szitkar et al., 2017, 2014) using different approaches (e.g. regional or local scale; ship-based or using underwater vehicles) with several degrees of success or limitation. Here we present results from acoustic surveys performed on the TAG hydrothermal district during the BICOSE (2014) and LEVE-SMF (2016) cruises and direct observation provided by HOV (Nautile) dives carried out during HERMINE cruise (2017). Acoustic data were acquired using two different multibeam echosounders (MBES): the hull-mounted Kongsberg EM122 (12 kHz, R/V L’Atalante) and the ROV-mounted RESON SeaBat 7125 (400 kHz, ROV Victor) (Figure 1). After processing, acoustic seafloor backscatter data from both MBES provides complementary qualitative results in relation to the seafloor composition. The analysis of the seafloor backscatter data obtained by near-seafloor surveys with the high-resolution 400 kHz MBES shows a clear relationship between low backscatter strength values and areas covered with pelagic and hydrothermal sediments whereas high backscatter strength values are associated to pillow lavas and basaltic scree. Intermediate backscatter strength values are rather related to old and younger eSMS as well as to mineralization on TAG active mound.

Jan 1, 2018

By R. R. Sacrison

The Barrick Mercur Gold Mine lies in the Oquirrh Mountains of northern Utah. Limestone, sandstone, shale, and chert are the predominant rock types being mined. Recent expansion has encountered rhyolite. Lithology and structural attitudes control most mechanical behavior. Slope steepening, mine planning, and site selection are presented as means by which geological engineering has contributed to the economics of the operation. Geomechanics investments of approximately $700,000 have resulted in cost savings or additional production worth over $16,000,000.

Jan 1, 1990

By Angus Maxwell, Jacob Grasmick

As the tunneling industry continues to adopt Tunnel 4.0, digital twins of the tunnel construction site are becoming standard requirements for tunneling projects. However, the benefits of these remain unproven to many practitioners. The paper discusses the various implementations of digitalization and describes efforts to combine all data types to analyze the relationships between influences, predictions and performance in a single digital platform. This includes data pertaining to investigations, design, construction, monitoring and post-construction asset performance and management. Based on 16 years of global tunneling projects the paper aims to quantify the tangible and intangible benefits of such systems. Using a number of real examples, the paper describes where opportunities were taken and where they went unrealized. Challenges and considerations for both procuring and developing these digital twins are also discussed.

Jun 13, 2021

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By Charles L. Kimbell

Introduction Despite the focus on the so-called "high-tech" and service components of the economy, the minerals industry in 1987 continued to provide the world the overwhelmingly dominant share of the total raw material supply for all manufacturing operations. And, in the form of fertilizers and other soil treatment materials, minerals also supplied indispensable raw materials to ensure continued high production of the agricultural and forestry sectors of the world's economy. Moreover, the role of minerals as a source of construction raw materials was essential to that sector. On the basis of preliminary and partial statistics on world output of crude mineral commodities, 1987 appears to have been a year of further recovery from the recessional years of 1981-1983. The value of world crude mineral industry production (all mineral commodities including fuels) apparently advanced about 5% to nearly $1.1 trillion in terms of constant 1983 dollars.' That is significantly above the recently revised 1986 level of nearly $1.05 trillion, but still considerably below the record-to-date high of $1.27 trillion set in 1980, as shown in Table 1. That growth in value took place despite relatively flat world oil prices - oil being the most important component of the aggregate, as it has been for decades. There is insufficient information available to assess the total value of processed mineral commodities (refined metals, refined oil, manufactured fertilizers and the like). But a figure of $2.6 trillion (constant 1983 dollars) would be a quite conservative estimate for those materials derived only from primary or newly mined materials. And an additional, as-yet-unestimated increment should be added for processed materials derived from secondary raw materials - scrap and other reclaimed substances. From a world trade viewpoint, minerals and mineral products dominate in terms of tonnage. For example, in 1985, on a weight basis, mineral commodities including fuels constituted more than 58% of all goods moving through the Suez Canal and 53% of all goods passing through the Panama Canal. These waterways cannot accommodate giant tankers and ore carriers. So an even larger share of total oceanic trade is composed of minerals and mineral products. Yet, in terms of value, the share of the total accounted for by these industrial essentials is much lower than that accounted for by other commodities, most notably sophisticated high-tech equipment and other goods with a relatively high per-pound value. Worldwide data on the value of mineral export trade for 1987 is so incomplete at this writing that it is impossible to assess that actual level. Indeed, the compilation of similar available data for 1986 covers only the exports of nations with developed market economies. In 1985, these countries accounted for only 67% of total world exports of all goods. They accounted for only 41% of world exports of major mineral commodities: crude nonmetals; metal ores, concentrates, and scrap; mineral fuels; nonferrous metals excluding gold; and iron and steel. For these developed-market-economy countries, the value of exports of these major mineral commodities declined by more than 10% between 1985 and 1986. Most of the shortfall came as a result of a 26% drop in the value of fuels exports. If these patterns of

Jan 7, 1988

By H. Walqui

The Empire concentrator currently processes magnetite ore from the Empire pit which is approaching the end of its mine life. Over the past two years plant wide tests have been run to access the plant capability of processing ore from the neighboring sister Magnetite pit. The neighboring pit presents challenges to the Empire plant due to its higher feed grade, finer liberation size and higher percent silica which require additional secondary grinding and concentrating capacity to achieve concentrate grade. The following paper summarizes the results from the second full scale test, run during 2009 under a challenging market environment

Jan 1, 2010

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

By Thomas G. Tavernaro, Jeffrey A. Schaefer

"The $106 million Olmsted Approach Walls Project, completed in the spring of 2004 by Massman Construction Co., Kansas City, MO, is one phase of a new $1.4 billion Corps of Engineers locks and dam facility located at Mile 964 on the Ohio River, approximately 17 miles (27.4 km) upstream of its mouth at the Mississippi River. When completed, the Olmsted Locks and Dam (Figure 1) facility will replace two aging locks and dams (Locks and Dams 52 & 53) built in the 1920’s, and produce an estimated $600 million annual economic benefit to the nation through reduced lockage time and operation and maintenance costs. PROJECT OVERVIEWThe Olmsted Approach Walls Project consisted of “in-the- wet” construction of four fixed nose pier structures, four floating concrete approach walls, one fixed wall and related underwater excavation, grading and stone placement. Over 12,000 tons (11,000 tonnes) of structural steel and pre-cast concrete elements, up to 335 tons (304 tonnes) in weight, were safely erected during the project.To support these massive structures, the Louisville District of the U.S. Army Corps of Engineers teamed with INCA Engineers, Inc., Bellevue, WA to design thirty seven 10’ (3m) diameter shafts (cast-in-place steel-shell piles) capable of maintaining elastic behavior below ground while resisting barge impact loads, extreme head-on collisions from runaway tows, and environmental forces from river current, wind, and seismic events.The shafts (typically 150’ (45.7m) in length) were founded 100’ (30m) into the riverbed through alluvium, a very consolidated fine sand and clay Cretaceous soil, and finally into a hydrothermally altered rock. Thirty seven shafts were installed under open river conditions at the site, a group of four shafts at each nose pier-pylon location (Figure 2), and 21 at the fixed land wall. Due to difficulty in achieving the required casing tip elevation the team developed a design modification that was successfully implemented for 27 of the shafts.Concurrent with the work at Olmsted, eleven pontoon segments for the four floating approach walls were constructed at a graving yard in Paducah, KY, developed by Massman Construction Company specifically for the project. While the pontoon geometry varied, the pontoons averaged 350’ (107m) in length, 40’ (12.2m) in width and weighed 4,500 tons (4,082 tonnes). The longest of the four walls, at 1,700’ (518m) was comprised of five interconnected pontoons."

Jan 1, 2006

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By A. R. T. Denues

This investigation was made under a cooperative agreement between the United States Department of the Interior, Bureau of Mines, and the Pittsburgh Testing Laboratory. Funds were supplied by the Chile Exploration Co., whose executive offices are in New York City. The support, cooperation, and services of these agencies made the work possible and are acknowledged gratefully. The writer wishes to express his particular indebtedness to the staff of the Explosives Division of the Bureau of Mines for services and assistance, particularly Dr. Wilbert J. Huff, consulting explosives chemist, J. C. Holtz, J. E. Tiffany, and A. B. Coates; to F. O. Gardner, treasurer of the Pittsburgh Testing Laboratory; to G. B. Holderer, consulting engineer in connection with liquid-oxygen explosives for the Chile Exploration Co.; to the Enos Coal Mining Co. of Oakland City, Ind., particularly to G. H. Utterback of the staff of the mine for providing facilities that made field tests possible; and to full-time assistants J. W. Rothhaar and J. G. P. Weinheimer and to W. S. Hiller, part-time assistant, who were employed under the cooperative agreement.

Jan 1, 1940

By P. J. Le Roux

"Mining companies are under constant pressure to reduce their cost structures to sustain profitability. In mines using an open stoping mining method, dilution often has a significant effect on profitability. At Target mine in South Africa, dilution in some open stopes was found to exceed 10%, falls of ground being a major contributor to the problem. This dilution can reduce the recovered grade from 5.5 to 4.5 g/t, resulting in a potential loss of about R21 million per month based on a gold price of R240 000 per kilogram. In addition to the cost of dilution, the cost of damage to, or loss of, trackless equipment as a direct result of falls of ground in open stopes is significant. Other associated costs include transport, hoisting, secondary blasting, milling, and plant treatment of waste material. Stable open stopes are essential in order to reduce falls of ground. Back-analyses of stope instability at Target mine have indicated that conventional rock mass failure criteria are unsuitable for stope design. An alternative strain-based criterion has been developed, and has proved to be very successful, allowing the stability of open stopes to be calculated reliably. Since its implementation in 2010, dilution and equipment damage have decreased markedly, creating value for the mine. IntroductionMines that make use of an open stoping mining method aim to extract only the ore, leaving the waste behind. Many orebodies have well-defined boundaries between the ore and the waste rock. In such orebodies, the introduction of waste into the ore due to overbreak dilutes the grade. In massive disseminated orebodies, dilution is less problematic. Overblasting, falls of ground, or other causes may result in dilution. A study undertaken in Canada (Pakalnis et al., 1995) found that approximately 51% of all underground metal mines utilized open stoping mining methods and, from surveys conducted at these mines, open stoping operations experienced dilutions of up to 20%, and occasionally more. Dilution of this magnitude has a significant economic impact on any mining venture. Research carried out in Australia by Capes (2009) came to the same conclusion."

Jan 1, 2017

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By D. Harrington

"Up to the last 10 or 15 years, responsibility for accidents in mines was generally, though not universally, placed upon the person or persons immediately involved. Present-day thought is rapidly veering toward holding the industry responsible for accidents, with ultimate payment of the bill by the consumer, if financial expenditure should be necessary. While it is undoubtedly correct in principle that responsibility for accidents in and around mines should be shouldered by the employer and while it is probable that as time passes the burden will become even more definitely than now that of the mining companies, on the other hand it is an undeniable fact that large numbers of accidents occur through acts of omission or of commission of some person, very frequently the victim of the accident being the offender.Out of about 3,000 persons killed every rear in our -mines and quarries, nearly half or approximately 1,500 of the fatalities are due to falls of overlying material or of persons, about 500 to haulage, about 350 to fires and explosions, about 125 to explosives, approximately the same number to electricity, and about 300 to various miscellaneous accidents.Generally the accidents from falls involve but one or two persons at a time, and the tendency is now as it always has been to charge the victim or possibly a coworker with the responsibility. Usually this sort of accident occurs at or near a working face (statistics indicate that about 80 per cent of fatalities from falls of roof or rib occur near the face), and as it is Generally agreed that it is the duty of the worker to keep his working place safe, the worker and especially the face worker is given the blame in case of accident."

Apr 1, 1930

By M. K. Quinn, A. W. Khair

"This paper presents an analysis of respiraple dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photo¬graphed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.IntroductionThe continuous-mining machines introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal sine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumo-coniosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (Newmeyer, 1981). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By J S. J van Deventer, D C. Shallcross

New developments are taking place in the recovery of gold from leached pulps that are based upon the adsorption of the metal cyanide species onto ion exchange resins. Despite the success of several resin-in-pulp pilot plant operations in the Western World and large-scale plants in the former Soviet Union, the process is yet to gain recognition as a viable alternative to the carbon-in-pulp process. An experimental research program has investigated the use of a variety of different types of resins for the recovery of gold, but to-date no resin studied has the desired properties of high selective loading capacity for gold cyanide and a simple inexpensive elution procedure. In addition very little is known concerning the physical strength of resins and their ability to resist shattering due to osmotic shock during cycles of adsorption and elution. The ability of ion exchange resins to enhance the leaching of refractory and re-adsorbing ores has not been investigated. This paper highlights the necessary factors that need to be addressed before commercialisation of ion exchange technology for gold extraction is feasible.

Jan 1, 1998

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

"9.1. IntroductionThe application of the electron microprobe for in-situ analysis of platinum-group minerals (PGM), first reported by Borovskii et at. (1959) and Genkin (1959), has resulted in a large and growing number of analyses of unidentified PGM. Figure 9.1 charts the increase in the number of reported unnamed PGM from 3 in 1959 to a total of 140 by 1979. All these minerals, with the exception of UN1968-5 and UN1976-1, were analyzed with the electron microprobe.There has been no recognised or consistent manner for reporting these unidentified PGM. The term ""unnamed"" has been used for PGM that are considered to be new species without a name as well as for PGM which have not been exhaustively compared to named and unnamed PGM in order to determine whether they are unique. Many of the so-called unnamed PGM are only unnamed because of poor microprobe analyses or because larger than usual elemental substitutions (e.g. Bi for As) made it difficult to calculate the true stoichiometry. Some of these unnamed minerals have been unnecessarily reported with non-stoichiometric formulae, as discussed by Cabri (1980). Better analytical data should reduce the number of such proposals.Another unfortunate practice, possibly used to by-pass the scrutiny of the Commission for New Minerals and Mineral Names, I.M.A., is to report a ""new"" mineral by referring to it by a name made up of its constituent elements. This has been deplored on a number of occasions (cf. discussion in Fleischer et at., 1976, p. 179), but some journals continue to publish such material. The Commission on New Minerals and Mineral Names has not recognised such ""names"" and these PGM are therefore included in this chapter with other unnamed minerals.A further example of inconsistency in reporting unnamed minerals is the report of a specific ideal stoichiometry with no further details (not even an analysis!); sometimes with a note that this will be reported in greater detail in due course. I have also been guilty of similar optimistic statements and, unfortunately, it is not always possible to follow through. Some authors give data on unnamed minerals in such a discrete manner that their reports are sometimes missed in literature searches."

Jan 1, 1979

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By Anthony (Sam) J. S. Spearing

Backfilling using coal waste is not a novel means for waste disposal throughout the world; yet, backfilling using a high density (paste) backfill is relatively new, except in Germany and Poland. One of the main benefits of a high density backfill, as opposed to a low density (slurry) backfill, is that, if placed at a low permeability and low moisture content, the risk of water table contamination can be relatively low. In addition, if paste backfill can be placed cost effectively, environmental benefits are huge because the surface impoundment footprint can be greatly reduced or even eliminated. This is especially true in room-and-pillar applications. In its current state, backfilling is considerably more costly than surface disposal. This is mainly because paste, as opposed to slurry, significantly increases backfill placement costs; however, this could be offset by increasing the achievable extraction rate. Overall, such a system could potentially improve the public?s image of coal mining in the US for a myriad of reasons. This paper discusses a proposed backfill system for a typical room-and-pillar coal mine in the Illinois Basin of the US and clearly shows the technical advantages, although costs are still higher with fill. The cost differential will likely reduce over time, in favor of the backfill option, as costs of traditional surface disposal increase, due mainly to ever-restrictive disposal regulations.

Jan 1, 2013