Search Documents

By A Gibbs

The mining sector has been a leader in investing in safety improvement initiatives, yet relatively few mining organisations can accurately track the positive effects of these initiatives or identify areas that may require more attention. The consequences of not taking safety seriously are severe, and unfortunately injuries and fatalities are continuing to occur across the mining sector (Brady, 2019). There is a tendency to turn to lag indicators such as All Injury Frequency Rate (AIFR), Total Recordable Injury Frequency Rate (TRIFR), and Lost Time Injury Frequency Rate (LTIFR) to track these outcomes. As outlined below these approaches are inherently flawed and a renewed focus is needed on indicators within the control of leaders, indicators that have high predictive validity for future events and data that is used in a way to enable learning and change.

May 5, 2022

By Albert E. Wiggin

PagE I. Early History of Boston & Montana Mill at Great Falls (1891 to 1905). 210 a. Original Mill Built in 1891.........210 b. Coarser Concentration Tried...211 c. Screen Sizing of Fine Jig Feed Introduced..211 d. Installation of Finer Grinding.......211 e. Steam Stamp Tried in Place of Blake Crushers..... 211 j. Mill Increased from Three to Six Sections........ 213 g. Tonnage Increased from 300 to 450 Tons per Section... 212 h. Round Tables Replaced by Wilfley Tables....212 I1. Hancock Jig Replaces Evans Jig...212 a. Description of Hancock Jig...213 - b. Tests Made on- Hancock Jig..213 1. Treating Natural Feed..215 2. Treating Sized Feed..215 3. Treating Classified Feed .215 c. Tests Made on Evans Jig...216 III. Richards Pulsator Classifier System...218 a. Experimental Work.....218 b. Installation of System in Section No. 4,....... 220 IV. Woodbury Classifier and Jig System.............222 V. The Great Falls System................ 222 a. As Installed at Anaconda............ 224 1. Coarse Crushing and Jigging Division...... 225 2. Hancock Jig Division........... 226 3. Fine Middling Division.......... 229 4. Table Division............. 230 5. Slime Division.........230 b. Special Features of Great ails Flow sheet....... 231 1. Development of Hancock Jig Flow Sheet..... 231 2. Development of Finishing Table Flow Sheet.... 232 3. Treatment of Coarse Middling Table Products .. 232 4. Results of Test Made on 500-Ton Section at Great Falls Mill...........234 VI. Comparison of Great Falls and Evans System at Anaconda.... 236

Jan 1, 1914

By Sato S, Kawaguchi T

The granulation and bed-permeability of sinter raw materials depend on interactions between the properties of various iron ores and water. The properties of individual iron ores are controlled by their particle size distribu- tion and surface characteristics, which can be described by representative particle size and wettability, respectively. Added water may be absorbed, affect granulation or lower bed permeability. These effects were experimentally studied as a function of properties of the iron ores. A mathematical model was developed in order to calculate the granulated particle size and permeability using the known blend of sinter raw materials. The calculated results were in good agreement with the observed values.

Jan 1, 1980

By R. Fraher

Hazard analysis utilizes interaction mechanisms in combination with geologic, structural and mining conditions to delineate areas of potential damage in seams subject to interaction. Using characterizations of conditions peculiar to multi-seam mining, such as innerburden thickness, geology and structures, initial interaction contour maps can be constructed. Geologic hazard analysis is then carried out on roof, pillar and floor conditions in the affected seam using lower seam rock properties and layout geometries in the overlying seam. Either safety factors or damage ratings can then be developed representing degree of hazard in the lower seam. The final hazard map shows both the aerial extent and magnitude of potential damage from interaction.

Jan 1, 1992

By Richard Harrison, Frank Lim

"Lifting of slurry from the seabed mining machine to the surface production vessel is a critical element of any deepwater seabed mining system. A Vertical Transport System (VTS) comprises pump(s), riser string, connectors and hang-off assembly as its main components, but it is the pipe material, riser configuration and installation method that often attract the most discussions.This presentation will feature important VTS design work 2H has done over the years for different stakeholders, and highlight the work carried out as a partner to the EU funded Blue Mining Joint Industry Project.The key challenges faced by a deepwater VTS are:??High riser payload??Large deck space for storing riser joints??Long time to deploy and retrieve riser??Uncertain metocean conditions??Vortex induced vibrations??Weld and connector fatigueIncreasing the water depth further sees the longer and increasingly ‘springy’ riser experiencing axial resonance caused by wave induced vessel heave motions being close to the riser resonant period. This can lead to snatch loading and fatigue failure in the riser.The presentation will discuss the above design issues, analysis requirements and provide guidance on pump/riser selection. Solutions to mitigate the resonant response issues will also be proposed.."

Jan 1, 2017

By Arthur W. Sheafer

MR. ECKLEY B. COXE, in his able and interesting paper on " The Preparation of Small Sizes of Anthracite,"* read and discussed at the Glen Summit Meeting, October, 1891, refers to the reputed immense amount of coal contained in the culm-banks, which are the unsightly accompaniment of every mining operation in the anthracite coal-regions. Mr. Coxe thinks the available amount and value greatly exaggerated, giving among his reasons (1) the spoiling of the culm by mixing with other refuse; (2) its deterioration; (3) its destruction by fire ; and (4) frequent failures to realize expectations as to the size of the banks. These points are undoubtedly important factors in determining the advisability of working any individual bank, but they have a varying influence in the several regions, some prevailing more in one than in another. Although the amount of fuel lying waste in these banks is still an uncertain and undetermined quantity, yet no one can visit the Schuylkill region without being impressed with the fact that a considerable amount of culm, too valuable to be left merely to the mercy of the elements, surrounds and encumbers each site of an old or present colliery operation. The rapid increase in the number of washeries, and the demand for leases on old culm-banks, shows that, in the Schuylkill region at least, the question of deterioration doès not play an important part. The proportion of coal to refuse, the relative percentage of the sev-

Jan 1, 1895

By João Paulo Melo Silva

No beneficiamento de itabiritos pobres (%Fe˜44,0) um dos principais desafios para as usinas de tratamento é a produção de concentrado dentro das especificações de qualidade e com menor custo. Nas usinas de beneficiamento a moagem é a operação unitária com o maior custo. Além disso, a moagem secundária é a operação unitária na qual a granulometria do concentrado é adequada às especificações para a etapa de flotação cleaner e para o transporte em mineroduto. Dessa forma, o aumento da eficiência energética no circuito de remoagem permite reduzir os custos e aumentar a eficiência do circuito de flotação cleaner. Amostragens de rotina e testes de bancada realizados com amostras coletadas no concentrador I indicaram oportunidade de aumentar a eficiência energética (kWh/t) da remoagem e reduzir a granulometria na alimentação da flotação. Com esse objetivo, foram realizadas alterações no circuito de remoagem do pré-concentrado da flotação mecânica do concentrador I da Samarco. Essas alterações consistiram em moer todo o pré-concentrado em circuito fechado reverso e não mais em dois estágios, sendo um em circuito aberto e outro em circuito fechado. Essas alterações realizadas no circuito permitiram aumentar a eficiência energética do circuito de remoagem, reduzir o consumo energético em 9,3% e adequar as granulometria e grau de liberação para a etapa subsequente de flotação.

Aug 16, 2017

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By M Binks

The Fosterville Gold mine is located approximately 20km to the East of Bendigo in central Victoria. The gold at Fosterville occurs as solid solution within disseminated arsenopyrite and pyrite. The Fosterville ore bodies contain various amounts of native carbon in the form of bituminous coal. This carbon (Non-Carbonate Carbon or NCC) has been the predominant mechanism for gold loss from the processing facility through”preg-robbing”.Processing of the Fosterville ore is achieved initially through crushing, grinding and flotation to extract the sulphides. The sulphide concentrate is oxidized using Bacterial Oxidation, before being leached in a conventional CIL circuit. A high portion of the native carbon (NCC) in the mine ore is naturally hydrophobic in nature, and subsequently reports to the flotation concentrate stream, and ultimately onto the CIL circuit. This NCC has a notable preg-robbing ability. Treatment of Black Shale ores, which have elevated NCC levels, has historically resulted in CIL recoveries as low as 35%, with around 60-80% of the gold loss from the leach circuit attributed to preg-robbing.Standard technologies for dealing with a carbonaceous leach feed have been trialed with limited success. The discovery of the significance of heat on leach recoveries, triggered extensive testwork on a range of leach feed and tails samples. Pilot plant testing demonstrated that “Heated Leaching” of the CIL tails was the best process with an average recovery increase of 7.5% being achieved. Following a successful pilot study, an engineering feasibility study was completed by Minerva Engineering, and the project economics determined. With strong recovery gains evident and a predicted project payback of 1-1.5 years, approval for the installation of the full scale plant was granted. Detailed design commenced in September 2008 with installation commencing in January 2009. The circuit was successfully commissioned in April 2009.Following commissioning, the Heated Leach circuit has achieved recovery gains of 4-14%, and has proven itself to be a significant contributor to the overall plant performance.

Aug 8, 2011

By S. K. Sharma

The Bureau of Mines' Tuscaloosa Research Center is conducting research to develop a basic understanding of solid-liquid separation in order to improve the dewatering of fine particle slurries. In the present investigation capillary suction time (CST) of kaolin slurries was determined. The average specific resistance of the cake was also determined by fitting the CST data to the theoretical equations used in this paper. The experimental data were analyzed by a powerful computer-based method, chemometrics, that uses statistical techniques to remove error and to find the number of physically significant factors contributing to the data. Results showed that two significant factors explain the CST data.

Jan 1, 1991

By D. G. Eskin

"It is well known that it takes some time for the solid phase to completely dissolve upon melting, especially inside the defects of insoluble particles, e.g. oxides. Until then the oxides remain active solidification substrates in the case of subsequent solidification. It is also known that ultrasonic melt treatment causes grain refinement through activation and dispersion of solidification substrates (one of the mechanisms) and also accelerates the dissolution of solid metal in the melt. In this study we combine these effects and demonstrate that the introduction of an alloy rod into the matrix melt of the same composition results in significant grain refinement, this effect being increased by the ultrasonic vibration of the rod. The achieved grain size is comparable to that obtained by a standard Al–Ti–B grain refiner. All samples were cast using a standard TP-1 mould to enable correct comparison. The effect of the temperature range of the rod introduction, as well as the effect of ultrasonic vibrations are discussed.INTRODUCTION The fact that by introducing solid metal into the melt one can achieve structure refinement is rather well known. As early as in the 1930s–1950s a series of papers and patents have been published, showing the benefits for grain refinement when dissolving solid metal in the melt before solidification (Danilov and Neimark, 1938; Scheil, 1956). Later on this way of structure refinement was developed further and dubbed “suspension casting” or introduction of “internal chills” (Madyanov, 1969; Zatulovsky, 1981). The solid metal was added in a form of cut wire, cut sheet, or powder, with the resulting grain refining, elimination of columnar grain structure in ingots and castings of steel, copper and aluminium alloys. The underlying mechanisms have been suggested as (1) rapid cooling of the melt due to the latent heat consumption upon melting of the solid metal with the resultant melt undercooling and (2) introduction of many solidification substrates in the form of crystal fragments and active non-metallic inclusions (Danilov & Neimark, 1938; Balandin, 1973). A number of patents have been filed where either the same solid alloy or a master alloy with additions (e.g. Ti for Al alloy) is introduced in the amounts up to 50% (typically less than 10%) into the melt close to the liquidus temperature (Schmidt, 1966; Talbot & Soller, 1973, Krupp, 1974; Bondarev, 1979). The main reason that this technique is not widely used in industry is the possible incomplete dissolution of the solid parts introduced into the melt with ensuing inhomogeneous as-cast structure and potential defects. Also the selection of the temperature range where the technology works the best is not clear."

Jan 1, 2018

By Sturchio NC, Williams SN, Fischer TP

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma.. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these "primary" components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

By Del Brock, Dan Wooton

The design/build of two adjacent vertical mine shafts in difficult ground conditions at a mining complex in the midwestern United States required innovative construction techniques. Construction of the 267-m-deep Service Shaft required full depth dewatering wells and ground freezing. Blind drilling was utilized to excavate the 257-m-deep Production Shaft and it was finished with a steel/concrete composite liner that was floated into place. An equally unique component of the installation included supplying a high capacity vertical conveyor system, featuring a 273-m-lift. Other components of the project include the mine level development, as well as the design and installation of three hoisting systems, including a 45-ton capacity men/materials hoisting system.

Jan 1, 2003

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By Satyendra K. Singh

If the extraction is beneath massive roof strata, the roof tends to 'bridge' across large spans without failing, the caving behaviour is complex and irregular. Understandably, these give rise to many geotechnical problems with safety implications and involving sometime huge direct and indirect costs. Only two important problems, 'feather-edging' in pillar mining and `severe periodic weighting' in longwalling, are discussed in this paper in the background of geomechanics investigations in Australia at Blue Mountain Colliery and in South Bulga Colliery respectively. `Feather edging'- a major source of injury and fatal accidents in Australia and South Africa in such situations, refers to a phenomenon where the roof, at the goat edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. The results of the first comprehensive, monitored trial in an Australian pillar extraction coal mine, suggests how the roof falls into feather-edging caving (generally) because of multiple shear-planes (interpreted) and how it may be alleviated. Because of complex fracturing behaviour of massive roof strata, periodic weighting at a longwall face is certain to manifest itself as 'yielding supports', heavy conditions', rapid convergence and in the worst case, as a cause of face stoppage. After briefly discussing the programme of instrumentation (in a chain-pillar and over the would-be goal) and results, this paper attempts to improve mechanistic understanding of the related geotechnical issues associated with the weighting behaviour and aims at establishing a 'threshold' value of weighting severity index (suggesting intensity of periodic weighting) with an objective to optimise operational controls before mining through potential (future) weighting areas.

Jan 1, 2000

By R. D. Leitch

"REASONS FOR AND PURPOSE OF WORKIn 1924 the United States Public Health Service was requested to undertake a special study of stream pollution. At that time the proposal that the United States Bureau of Mines take up the study was made by the Public Health Service because in point of training and experience the personnel of the latter was considered not to be as well, suited to this type of investigation as was that of the Bureau of Mines. H. Foster Bain, then Director of this bureau, promised to undertake the work, and, accordingly, field investigations were begun in the spring of 1925. The problems of mine-drainage wastes and of gas-house and coke-oven waste were investigated in the laboratory, and a method of treatment by sodium hydrate and benzol was found to be promising. The idea was obtained by A. C. Fieldner, chief engineer of the Bureau of Mines experiment stations, while in Germany in 1924, where he was shown a practical application of the process, but no information was obtained as to definite chemical or mechanical processes. Because of the then pending American patent application by the German firm, we made no attempt to develop our findings further. Shortly after, a similar method of treatment was developed in the United States, and since that time we have devoted our attention entirely to mine drainage. This paper is a presentation of some general facts and information gathered during the past five years on coal-mine drainage.SCOPE OF WORKAt the time our work was begun there was such a diversity of opinion on the whole subject and apparently so little was accurately known, that it was decided to undertake a basic study from which (1) certain definite information might be evident, and (2) what might be considered side issues of the original investigation would be suggested for subsequent study.A stream in a district thought to be representative of those in low to average sulphur bituminous coal fields and another in a high sulpbur district were selected for study, A fair (weber of factors entered into the tentative selection of these streams, the chief ones being their accessibility and freedom from other industrial or domestic pollution, besides, of course, the presence of mine drainage in these streams."

Apr 1, 1931

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By Thomas Fraser

IN a Nation-wide appraisal of coking-coal reserves and of the feasibility of expanding them by upgrading marginal coals, it is natural that the Pittsburgh region of Pennsylvania should be considered first. Here, where the American iron and steel industry started, the Pittsburgh coal bed is of paramount importance. The use of coke in iron blast furnaces is said to have begun with the discovery that good blast-furnace fuel could readily be made by a simple method of coking Pittsburgh coal. To the present time, the prosperity of the steel industry has depended largely on utilization of this great coal reserve and the cheap transportation afforded by the Monongahela River system. OBJECT AND SCOPE OF INVESTIGATION The initial project in the study of upgrading marginal coking coals was laid out in this area, which contains large reserves of Pittsburgh coal contiguous to the Monongahela and its navigable tributaries. Much of the Pittsburgh coal remaining here is known to have a high sulfur content. The problem of reducing the sulfur to meet metallurgical requirements already has received much attention, and it is considered to be one of the most difficult technologic problems in the field of coal washing.

Jan 1, 1950

By Fernando Linares Quiroa

El diseño y operación de la mina es un proceso importante para la construcción de un modelo de cuerpo mineralizado. En este sentido, el presente texto describe la trascendencia del modelo geológico, construcción y uso de este para la extracción del mineral, donde este es una representación de la realidad que se genera a partir de la información predecible y proporciona a los geólogos e ingenieros de planeamiento los recursos más adecuados para una efectiva selección y extracción del mineral tanto física como económicamente. Asimismo estos bloques permiten la manipulación de la información contenida en estos a una escala local y describen contenido sobre las características tales como: leyes, dureza, peso específico, RQD, litología, mineralización, alteración, metalurgia, etc. Finalmente, los usos que se dan a los modelos de bloques se aplican al control del mineral, planeamiento a corto, mediano y largo plazo, el cáculo de los recursos geológicos y las reservas minerales, constituyéndose en la base para la optimización y del diseño del tajo.

Jul 31, 2003

By L. Lü, M. O. Lai

"Mechanical alloying is a dry, high energy ball milling process which has been used to synthesize metallic powders in the solid state. The present study use this technique to synthesize Cu-base shape memory alloy powder from commercial Cu70Zn30, Cu86Zn14 and element AI powders. The evolution and formation of shape memory alloy powder were monitored using X-ray diffraction and microscopy. It was observed that shape memory alloy powder started to form after 1.8 ks of mechanical alloying. ? phase was clearly detected after 3.6 ks of mechanical alloying. The intensity of X-ray diffraction of the y phase increased when mechanical alloying duration was prolonged indicating an increase in the amount of y phase. Microstructure observation showed different stages of formation of alloyed powders: welding between powders and formation of layered structure, deformation and fracturing of layered structure, and finally the formation of alloyed powders.IntroductionMechanical alloying (MA) is a process used for producing powders with controlled and extremely fine microstructure. It was original developed in 1966 (1) to produce aNi-based superalloy combining oxide dispersion strengthening with gamma prime precipitation hardening. In recent years this technique has been used in producing a wide range of materials including intermetallic compounds (2, 3), amorphous materials (4-6) and other materials (7-9). In MA, a blend of powders is subjected to highly energetic compressive collision. The powder panicles are welded and fractured during ball milling. Therefore, it is essential that at least one of powders should be ductile to act as combiner. It has however been found that brittle components without soft element can also be mechanically alloyed (10), even ceramic powders (11).The present work aims to study the mechanism of formation of shape memory alloy powder during MA."

Jan 1, 1994