Search Documents

By Donald E. Stump

Subsidence from underground coal mining alters surface water discharge and availability. The magnitude and areal extent of these impacts are dependent on many factors, including the amount of subsidence, topography, geology, climate, surface water - ground water interactions, and fractures in the overburden. These alterations may have positive and/or negative impacts. One of the most significant surface water impacts occurred in July 1957 near West Pittston, Pennsylvania. Subsidence in the Knox Mine under the Coxton Yards of the Lehigh Valley Railroad allowed pan of the discharge in the Susquehanna River to flow into the mine and create a crater 200 feet in diameter and 300 feet deep. Fourteen railroad gondola cars fell into the hole which was eventually filled with rock, sand, and gravel. Other surface water impacts from subsidence may include the loss of water to the ground water system, the gaining of water from the ground water system, the creation of flooded subsidence troughs, the increasing of impoundment storage capacity, the relocation of water sources (springs), and the alteration of surface drainage patterns.

Jan 1, 1986

By Phillips J. T, Hutton W. A

This paper discusses why Argyle Diamonds adopted thickened tailings disposal in 1985 and how the system was developed over the next seven years. A wide ranging review of the thickened tailings disposal system and the tailings deposit it was producing was carried out during 1992 and 1993. The results of that review led to the abandonment of thickened tailings disposal at Argyle because of serious concerns about the stability of the resultant tailings deposit. The exposure to the risk of liquefaction and an assessment of the consequences if this happened to the thickened tailings deposit are shown. The criteria for selecting the new tailings disposal strategy are then described. The final section of the paper discusses the management strategies that have been put in place. These are designed to: ò reduce the risk posed by the thickened tailings deposit to an acceptable level; ò safely store tailings to the end of mine life; ò produce a land form that can be decommissioned to the satisfaction of Government regulatory bodies.

Jan 1, 1996

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009

By Truman P. Stauffer

Secondary use of mined-out space in underground limestone quarries is emerging in the Kansas City area where abandoned quarry sites are being renovated into warehouses, factories, and offices. Mining techniques, ceiling heights, and pillar distribution are being altered as planning for the secondary use of mined-out space is combined with the quarrying process. Even the historic urban- quarry land use conflict invites a reappraisal in that this development provides a potential resolution of the problem. Mutual subsidization by dual rock and space interest is changing the economics of rock production. A city is much more than a surficial adjunct superimposed upon the topography of an area. Its development and growth are deeply rooted in the resources, benefits and problems of its underlying geology. The environmental geologist must address himself to more than the quality of a particular resource. He must comprehensively relate resource extraction and processing with the urban emphasis of optimal use which favors long term usage of land over one time economic ventures. Limestone quarrying, closely allied with the growth of many cities, has commonly left a series of scarred landscapes in the path of the burgeoning metropolis. These abandoned quarry sites are barriers to orderly city growth and fail to serve the people as useful and taxable land. Where quarries are functional, supplying the city with needed growth minerals, problems of blasting damage, noise, and dust exist. Technology faces the challenge of making mineral production and processing good neighbors to the urban market they serve. Continued growth of cities may require more efficient use of space below as well as above the surface optimizing land usage so that long term economic benefits may be reflected in improved mining methods.

Jan 1, 1973

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields, with rapid depletion of existing reserves, emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry for meeting increasing market demands; but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields. Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most current operations are of the pressure-maintenance type, in which the reservoir pressure is maintained or partly maintained by injecting natural gas to in-crease oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes current gas-and water-injection projects in California.

Jan 1, 1952

By D. P. Gold

Major sources and reserves of Cb/Nb, Ta, REE, Y, Sc, Zr, Hf, Cu, apatite and vermiculite may be concentrated in primary and secondary minerals associated with different stages and depths of emplacement in carbonatite complexes and kindred alkalic intrusive rocks. Exploration targets include: apatite and pyrochlore (Nb) in the plutonic and hypabyssal core and ring-dikes: bastnaesite (REE), strontianite, barite and fluorite in hydrothermal veins and cone-sheets (subvolcanic setting): thortveitite (Sc,Y) and vermiculite in metasomatized aureoles (fenites): high grade eluvial deposits of apatite and pyrochlore, and secondary REE, Nb, Ti. and V-minerals in supergene and weathered zones.

Jan 1, 1991

By M. A. Giralico

Solvent Extraction (SX) technology has undergone significant refinements including outright process changes to achieve greater copper production rates with lower organic entrainment levels. LIGHTNIN has completed a detailed study aimed at improving on the conventional Holmes & Narver and Davy Power Gas type impeller designs1 by optimizing the mixing through the use of high efficiency pumper turbines instead of making system changes as others are doing. Since each individual installation requires a different design head and flow, LIGHTNIN has developed the R320 "family" of high efficiency, curved blade pumper turbines. These impellers are designed to maximize head and flow while reducing entrainment through lower power consumption, less shear generation and turbulence, elimination of air incorporation, production of the optimum droplet distribution, and lower tip speeds. These improvements also maintain the required mass transfer and copper recovery of the traditional impeller designs. The R320 impeller benefits have been quantified using Laser Doppler Velocimetry (LDV) and proven in multiple domestic and foreign installations at flow rates exceeding 15,000 GPM. Design comparisons of this improved impeller type versus traditional technology impellers in head, flow, power and entrainment are presented for review. In addition, the inherent benefits of axial flow, high efficiency impellers like the A3 1 0 and A6000 in auxiliary mix chambers will be discussed. The high flow, low shear characteristics of these patented impellers provide the necessary dispersion stability for mass transfer while speeding phase disengagement in the settlers due to low power and low shear input.

Jan 1, 1995

By E. P. Wiechmann, J. A. Henríquez, P. E. Aqueveque, L. G. Muñoz, G. A. Vidal

"The original segmented intercell Optibar succeeded in reducing the magnitude and occurrence of short circuits. It also improved the specific energy consumption of the process. This paper expands the load current source concept introducing a triple segmented bar. This new bar adds immunity to dirt contacts and open circuits. Moreover, it further improves the standard deviation of current densities. As compared with industrial practices this development should accomplish an 8% specific energy reduction. Also, a plant implemented with BBS should be able to work with 12.5% higher process currents than Walker without compromising the operation.INTRODUCTIONIn 2011 the technology based on current mode was implemented at industrial scale. The success of this technology moved CIM Magazine (Lanktree, 2011) to write in the Jan 2012 issue an upfront story of this technological innovation. To cover the story, the technical reporter Graham Langtree was appointed by Peter Braul Editor of the upfront section. The article tells that “More than 40,000 tonnes of copper have been refined in a year-long test run of Optibar Inc.’s new technology at Barrick Gold’s Zaldívar copper plant in northern Chile. The new segmented intercell bars being used in the Compañía Minera Zaldívar refinery have slashed energy costs, reduced short circuits during refining and allowed the production of heftier, purer sheets of copper – gains that all promise to boost the plant’s margins. A copper refining tank house containing the cell circuits typically consumes 2,000 kWh of electricity to produce a single tonne of grade-A copper. Yet, monitoring the energy efficiency of the Optibar technology after increasing the weight of harvested copper sheets, the project’s engineers recorded a 92 kWh-per-tonne cut in energy consumption, a savings of 4.6 per cent. “Today, with the power prices we have, Optibar technology represents a potential savings for the whole plant of US$1.5 million per year,” says Robert Mayne- Nicholls, executive general manager of Barrick Gold’s Chilean operations.”"

Jan 1, 2012

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971

By M. Pfeifer, M. N. Brodie, D. J. Barratt

"This paper reviews design trends related to the various SAG mill configuration and drive options available today. The impact of these options on capital and operating costs is assessed, and key technical issues reviewed. The discussion is based on the conventional North American ’pancake’ mill configuration. IntroductionDuring the past decade mill technology has evolved significantly in the following key areas:• improvements in variable speed motors continue with on-going advances in electronics;• ring motors, or gearless drives, are becoming more common in mill sizes 32 ft and larger, with ratings of 10 000 HP and greater;• geared drives have become available up to ratings of 9500 HP per pinion, compared to the earlier 6000 HP guideline;• improvements in speed reducer technology due to the use of carburized and ground precision gearing, make the high speed motor-speed reducer drive more competitive with the direct coupled low speed motor drive;• a unique speed reducer drive is being introduced to this industry which combines ring gear drive pinions with speed reduction. mprovement in gear alignment is claimed, and the overall drive arrangement is more compact than is possible with a conventional speed reducer drive;• the first 38 ft and 40 ft diameter mills have been designed and manufactured; and • application of large multi-shoe bearings have made shell supported mill configurations available for all, including the largest sizes. These designs have flat instead of conical mill shell ends, and have the potential for technical and cost advantages compared to conventional trunnion supported designs.This proliferation of mill design features provides several options to those involved in planning and design of milling plants, and requires more extensive evaluation to optimize mill design features to best suit specific project requirements."

Jan 1, 1999

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note. This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material In which the crystals here dealt with were grown was made from 1/8 -in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of travelling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection.

Jan 1, 1927

By MattelmSki M

Outokumpu Harjavalta Metals Oy has been producing nickel since 1962, based on conventional flash smelting technology followed by electrowinning of nickel. In the 1980s, a research project was initiated to develop a converterless direct smelting process to produce matte for further refining in the then existing refinery. The process was tested on a pilot plant scale at Outokumpu's research centre in Pori and was found to be viable. The process was named the Direct Outokumpu Nickel Smelting Process or the DON Process. At the turn of the 1990s, Outokumpu studied various options to develop its nickel business and the Harjavalta operations. As a result of this work, the DON Process was further developed to produce two mattes: low iron matte in the flash furnace to be leached in the existing leaching circuit and high iron matte in the electric furnace to be leached in the new leaching circuit. In Harjavalta's case, it was essential and important that the process could use the existing flash furnace and electric furnace without converters.

Jan 1, 1996

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By Olivia Perkins, Shawn Sismondi, Adrian St. John, Vicky Potts

"INTRODUCTION An inherent aspect of any tunnelling project is ground risk: how it is identified, quantified and managed throughout the various stages of a project. Early identification of these risks, such as adverse ground conditions or potential obstructions is crucial; however specific identification of all risks will inevitably be limited by the extent of the desk study, ground investigation and accuracy of as-built information available, particularly in a densely populated urban environment such as London with a long and varied history of development. It is therefore crucial to have suitable plans and procedures in place for dealing with potential ground risk scenarios if they occur during construction work to ensure the safety of the workforce and to protect nearby critical assets. A number of experiences of potential ground risk were encountered during the Sprayed Concrete Lining (SCL) works on Crossrail contract C300/410 which was constructed by a joint venture of BAM Ferrovial Kier (BFK). The C300/410 works, undertaken in the heart of London, comprised of over 2.5km of SCL tunnels for Bond Street and Tottenham Court Road Stations and the Fisher Street crossover, as well as two 6.2km TBM tunnel drives between Royal Oak and Farringdon. BFK appointed Donaldson Associates as their SCL designers for the works; together they were responsible for excavation stability up to the point of ring closure. Despite the majority of SCL tunnelling works at Bond Street and Tottenham Court Road being through the favourable medium of London clay, there remained areas of local geotechnical challenges. Some of these were expected from the outset, some became apparent as works progressed from records of other nearby excavation works, and some were only encountered during tunnel excavation. Being located in the centre of London meant that there always remained a possibility of meeting some form of obstruction from previous structures. However, identification of all potential issues prior to the commencement of the works was challenging and proved to not be entirely possible. Through a series of case studies, this paper documents incidents where obstructions or adverse ground conditions arose. These scenarios all had the potential to cause safety risks, impact the tunnel design and/or construction methods and ultimately add time and cost to the works. The paper discusses how these challenges were overcome which utilised in part, a progressive risk reduction cycle, feeding back knowledge gained at all stages of construction into the approach for undertaking the works. It also examines what could be done in future to further reduce the ground risk through early identification, communication, education and appropriate contingency measures."

Jan 1, 2016

By G F. Johansen

The erratic and localised occurrence of economic gold grades is a common feature of high-nugget effect gold veins. The nugget effect is a consequence of small-scale geologically controlled enrichment, and the inclusion or exclusion of sparse gold particles because of the sampling process. Such deposits do not always contain visible or coarse gold, and can be characterised by fine gold particles. Economic grade accumulations are generally contained within discrete oreshoots, which are surrounded by barren to low-grade material. Problems are often encountered where small sample types (eg drill core or channel samples) often vastly understate in situ grade, due to their general inability to intersect rare gold particles. As a result, the definition of grade and its distribution is often challenging, and leads to substantial resource uncertainty. Proxies, or indicators for grade, can help the geologist gain a better understanding of grade distribution and grade potential. These are based upon geological (eg mineralogical, textural, etc) and/or geochemical (eg specific elemental ratios, fluid inclusion compositions, elemental correlations, etc) criteria. The paper discusses the use and application of such proxies through three case studies.

Jan 1, 2004

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By D. C. Foote

MR. FOOTE: This paper deals with blasting and mechanical loading. The Union Pacific Coal Company does all of its blasting with permissible powder and electric shooting, but this paper deals principally with blasting in connection with mechanical loading. With the introduction of mechanical loading into the coal fields of southern Wyoming one of the main problems to be taken into consideration was the drilling and blasting of the coal. The methods used in blasting coal for hand loading were found to be ill adapted to the mechanical practice, so numerous tests were conducted from time to time to determine a system or systems whereby the coal might be blasted in a form to be easily handled by the loading units. The general practice in blasting coal for hand loading, for example in a room 24 feet wide and seven feet high with an undercut of seven feet, would be to shoot one or two strong breaking shots in the center and one on each rib. While much of the cut would be blasted down in good lump, some coal would be left hanging at the back and ribs. With hand loading, the miners would have time to pull this coal down with a pick between cars and eventually would clean up the place ready for the cutting machine. The loading machine, however, cannot get this coal down and its operation would be delayed while the men were doing the necessary pick work.

Jan 1, 1929

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

Green mining is the latest technological advancement to reduce mining’s environmental impact with minimal energy and resource consumption. Green mining — aimed at protecting nature and providing socio-economic benefits — is a multifaceted network of its connotations and key indicators. China has not yet defined its connotation and formed an effective evaluation system for surface mining. We defined its connotation and developed an evaluation index system based on the theory of green grades. As the indicators are selected based on extensive research, they express the advantages and disadvantages of various aspects of a mine. The index is composed of three attributes (safety, efficiency and environment), nine criteria and 35 indicators. The indicators were quantified according to experts’ opinions using the fuzzy comprehensive evaluation method. The results of a case study show that the environment is the most critical aspect, followed by efficiency and safety. This study can provide technical support for the development of green mining.

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022