Search Documents

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By Jason Swartz, Gerardo Gomez, Henry Leighton

San Antonio has experienced sustained growth for decades, putting increased pressure on existing wastewater infrastructure. In June 2013, San Antonio Water System (SAWS) reached a Consent Decree agreement that requires significant improvements to the wastewater system over a 10-year period to reduce Sanitary Sewer Overflows. One of the critical projects was the W-6 Upper Segment Tunnel project to reduce sanitary sewer overflows on an existing sewer main running through Lackland Airforce Base. The replacement project consisted of a new tunnel nearly 29,000 LF of primarily 104" FRP. The project also includes nine shafts and multiple trenchless crossings to make near surface connections to the new works.

Jun 23, 2024

By A. D. McMahon

Changes in world mine and smelter supply sources of zinc have led to changes in zinc supply patterns in the United States during the past 3 years, 1970-72. The result has been a growing reliance on foreign sources of zinc metal to furnish an ever-increasing portion of expending domestic requirements. This review of fundamentals and historical developments is intended to provide background in order to place the future of the U.S. zinc industry fn perspective. The properties and uses of zinc are described. A new study on U.S. reserves is presented with description by geographical region and comparisons with older reserve data. The technology of the zinc industry from prospecting through refining is described with emphasis on the metallurgy involved in the various methods of smelting. Production, consumption, and imports are discussed and illustrated with graphs and tables to review the past and present patterns. Government actions affecting the industry are shown.

Jan 1, 1974

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

By W. P. Diamond, J. R. Levine

The explosion hazard of methane-air mixtures has become an increasingly serious mine planning problem, and an advance assessment of methane gas potential can therefore be essential for a safe and economic mine development pro- gram. As part of its coal mine health and safety program, the Bureau of Mines has developed a simple, inexpensive test to measure the methane content of coal samples obtained from exploration cores. The gas content of coal per unit weight as determined by the direct method test can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if degasification of the coalbed in advance of mining should be considered. Since the Bureau began measuring the gas content of coal samples in 1972, experience has led to equipment and procedural changes, the most significant of which has been the development of a ball mill for crushing the coal sample to release the residual gas at the end of the desorption test period. This revised procedure replaces the crushing box and graphical methods described in earlier Bureau publications. The results of 583 direct method tests are summarized in tabular form. These results include data on the gas content of 125 coalbeds in 15 States.

Jan 1, 1980

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds. Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a ?diamond friendly? method of comminution. Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso).

Jan 1, 2012

By Darling Elías Montoya

El presente trabajo señala la importancia de la cuenca del Marañón en tanto representa un ambiente idóneo de deposición aurífera para el ámbito nacional. La cuenca se encuentra situada entre los centros poblados de Borja-Saramiriza-Puerto América de Madre de Dios, cuyas condiciones desarrollan posibilidades de deposición de oro aluvial. El estudio prospectivo fue empleado por personal técnico de la gerencia de exploraciones de Centromin Perú.S.A en el que obtuvieron 26 muestras referenciales, encontrando 100 000 hectáreas de interés prospectivo por oro fluvial.

Apr 1, 1991

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9

Jan 1, 1923

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By G. Belardi

This paper presents the preliminary results of a research programme conducted to assess the feasibility of a flotation technique in the remediation of soils severely affected by heavy metal contamination. The use of flotation in soil remediation is a recent practice. The main difficulties are given by the variety and peculiarity of the heavy metal containing species, and also by the grain size. Most of the studies reported in the literature concern the use of conventional collectors, such as xanthates, after a preliminary chemical modification of the metal bearing species through sulphidization. On the basis of the minera-petrographic characterization and of speciation, some classes of reagents have been selected, capable of acting both on metal-bearing species and all metallic cations to be separated. The design of the synthetic molecules has been based on the coordinative properties of the metallic centres and functionalized in order to act as collectors for a wide range of metals independently on their surrounding atoms. In laboratory experiments a sample of stream sediment has been utilized, whose contamination is caused by the runoff from Sardinia mine waste dumps and overflow from the settling ponds. The material showed contamination mainly from Zn, Pb and Cu and to a lesser extent from Cr, Ni, Cd, and Sb associated in mixed particles of Fe and Mn. Flotation tests on a laboratory scale have been performed on grain sizes less than 355 µm in laboratory cell Minerais & Metaux. The effects of the structure of collectors (functional group, chain configuration) as well as of the principal flotation parameters (such as pH, concentration of reagent) on the grade and recovery of heavy metals in the concentrate and in the tailings (remediated soil) have been investigated. The results of the laboratory tests substantially confirm the theoretical premises, and the most effecive reagents found belong to the classes ATP, MBT, MBO, fat acids and phosphates.

Jan 1, 2014

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By M. Pillay

INTRODUCTION Heat stress continues to be a safety concern in underground mining. This is due to a number of reasons including increasing depths of mining, increased levels of heat generated from machines, ventilation systems being constrained from providing suitable levels of airflow and others. In order to assess if a thermal environment is safe for miners under normal or modified work arrangements, or to specify stop work conditions a heat stress index is used to guide decisions. Historically, a number of heat stress indices have been developed and applied in underground mines. These can be classed under three broad headings; single measurement, empirically based and rational indices. Do any of these indices perform better than the others? Which one allows simple determinations and decisions to be made in the mine? This paper aims to provide answers to these questions by comparing and contrasting three indices; effective temperature (ET), simple air cooling power (ACP) and Thermal work limit (TWL) for a range of typical mining wet and dry bulb combinations? The paper concludes with the identification of areas for future research. BACKGROUND Heat stress causes discomfort, increases physiological strain, decreases productivity and performance, and contributes to increased incidents [1]. Effective management and control of heat stress is particularly important in mining where hot working conditions are very common [2]. Heat stress index is a common indicator that is used by mine safety advisors and managers to guide decisions about safe work practices in mining under normal or modified conditions. According to Howes and Nixon [3] A safe heat stress control strategy for an underground mine has three elements: • Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. • Acceptance of a functional relationship between the environmental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. • A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The link between these elements is an environmental measure that reflects the physiological strain a worker is subjected to. Since the turn of the twentieth century various indices of thermal stress have been developed (McPherson [4], Howes and Nixon [3], Brake [5]). In selecting a suitable environmental measure or index one problem that must be addressed is the ease with which it can be physically obtained relative to it accurately reflecting the physiological strain. No index can be universally applied and there is no single correct measure or index. However if an index has provided adequate control in a particular circumstance, then it can be regarded as correct for that situation.

Jan 1, 2019

By G Harbort

Traditional engineering design for flotation circuits use the “Rule of Thumb” approach. Typically this uses a nominated maximum head grade for design. A scale-up factor is applied to laboratory flotation tests for residence time. This scale-up factor is usually based on a designers experience at other flotation sites and may or may not be relevant to the circuit being designed, or the flotation equipment being used. A small number of locked cycle tests are assumed to represent the ore body and the results of these are often used for financial analysis, independent of changes in mine plan throughput and mineralogy.The engineering “Rule of Thumb” approach is only strictly accurate where there is very little variability in throughput, head grade and mineralogy. It may provide accurate design for mature established operations where a brownfield expansion is being considered but is unlikely to provide accurate design for a new, greenfield site.The use of geometallurgical modeling with floatability component simulation provides a design methodology with significantly less associated risk. The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to use spatial metallurgical information to drive production planning, mine planning, blast design, blending strategies and plant set-up. At a design stage the process designer can use geometallurgical information to evaluate bottle necks and potential design flaws and propose the best investment strategy for the project benefit.This paper details the geometallurgical characterisation of the Andash deposit and methodology used to review the project’s detail design and projected production.

Aug 8, 2011

By Washington Luiz Mafra

Every year the conventional direct reduction processes ? Midrex and HYL III ? increased their market share in the world steel production, even though they are only economically feasible in countries where natural gas is available at competitive prices. In this context, the new Midrex projects are based on large reactors (Megamod - 1.5 to 1.8 Mt/y of DRI), reduction temperatures of the metallic burden up to 850oC, with bustle gas temperatures between 960oC e 1050oC. Thus, the requirements of metallic burden performance, as well as the evaluating methods, usually based on ISO standards, need to be reviewed. It is well known that the standards usually applied to quality evaluation do not reflect the performance of metallic burden inside the reactors. This paper describes the different methods of evaluating the disintegration under reduction of DR pellets based on ISO 11257 standard. This is the most important method used by pellet producers and customers for evaluating DR feedstocks. The different methodologies tested to evaluate the disintegration under reduction had varying results, evidencing the relevance of the method and the quality of the pellet. Nevertheless, validating the method in an industrial reactor is still fundamental.

May 1, 2007

By F. P. Haver

The Bureau of Mines has investigated the electrochemical reduction of lead chloride as a method for producing lead without the pollution problems associated with smelting. It was determined that high-purity metal (>99.9 pct Pb) could be obtained, using PbC12 prepared by ferric chloride leaching of galena concentrate: PbS + 2FeCl3?PbCl2 + 2FeC12 + S°. Optimum results in small-scale electrolytic tests were achieved with a bath consisting of 40 to 70 wt-pct PbCl2 dissolved in KC1-LiCl eutectic, an operating temperature of 450° C, a current density of 2.5 amp/in2, and an electrode spacing of 0.5 inch. In large-scale tests made to develop a cell design for commercial application, the optimum electrode arrangement proved to be a bipolar configuration with horizontal plates. This gave a current efficiency of 86 pct with an energy requirement of 0.52 kwhr/lb lead. To determine the effect of impurity buildup in the bath, 1,200 lb of PbC12 prepared by ferric chloride leaching of galena concentrate was electrolyzed over a period of 2 months. Little deterioration of the metal quality occurred in that time; all of the lead produced had a purity equal to or better than corroding grade (>99.94 pct Pb).

Jan 1, 1976

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S. I. Freedman

Coal-oil mixture (COM) combustion technology is regarded by the Department of Energy as near term, and potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers, into blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally-acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1978

By M. Hao, S. Hu, X. Lyu, M. Lian, C. Anning, G. Yao, Z. Wang

The results revealed that the pozzolanic activity of the gold mine tailings and their main mineral phases improved by mechanical activation. Under the same activation conditions, the activated mica powders possessed the highest pozzolanic activity index, followed by the activated feldspar, and the activated quartz exhibited the lowest pozzolanic activity index. The addition of calcium oxide promoted the formation of amorphous C–(A)–S–H gel for all paste samples, and stratlingite and hydrotalcite were observed in calcium oxide activated mica paste. The addition of natural anhydrite promoted the formation of ettringite for the pastes of calcium oxide activated aluminosilicates materials (gold mine tailings, mica, and feldspar). Furthermore, the pozzolanic activity indexes of the mechanically activated gold mine tailings and their main mineral phases were tested to be qualified for use as supplementary cementitious material in cement. This paper provided an innovative approach for recycling gold mine tailings as supplementary cementitious materials in cement, which would be environmentally friendly and cost-effective. Keywords: Mechanical activation, gold mine tailings, supplementary cementitious material, hydration properties, pozzolanic activity

Jan 1, 2020