Search Documents

By C. G. Bruce

"ON NOVEMBER 15th, 1950, the Department of Mines and Technical Surveys announced the discovery of vermiculite near Perth, Ontario. The announcement followed nearly a month of study to determine so far as possible the potentialities of the deposit and quality of the material from surface indications. The mineral was identified by the writer in the field among samples submitted by Mr. Arthur Powers of Stanleyville or, September 22nd, 1950. Within a week of the announcement, mining rights to properties covering a major portion of the deposit had been acquired by commercial interests.Hitherto, Canada has had to import her entire requirements of vermiculite. Prospects of .a domestic supply gave promise of considerable benefit to many industries, particularly the building industry, and to the consumer public. Should the deposit •prove large enough there was also the possibility of exporting to centres in the United States.Field and laboratory studies were continued at the Mines Branch during the winter of 1950-51 as opportunity occurred. It is the purpose of this paper to describe the results of these •preliminary investigations, to attempt to present the Stanleyville occurrence in its proper perspective with regard to similar occurrences elsewhere, and to review the salient features of the vermiculite industry.Properties and UsesVermiculite is a hydrated magnesium aluminum silicate. In appearance it resembles mica, having the same micaceous cleavage, but it differs from that mineral in being very soft, pliable, and inelastic. Colours range from black through dark olive-green and brown to almost colourless."

Jan 1, 1952

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By P. S. Baker

CRU estimates that the global supply of metallurgical grade alumina (MGA) grew by 5 percent during 2005 to a little more than 61 Mt (67 million st). About 30.7 Mt (33.8 million st), or 50.3 percent, of that originated from Oceania (principally due to the commissioning of the CAR refinery in Australia) and Latin America. In this context, Chinese production surged by 20.5 percent year-on-year to 7.7 Mt (8.5 million st) on the crest of a 17-percent rise in that country’s primary aluminium production. Meanwhile, on the demand side, there was a 6.7 percent climb year-on-year in global consumption to 62.3 Mt (68.6 million st). This reflected a healthy demand for primary metal from aerospace, construction, packaging and passenger transportation (to a lesser degree) in the United States, China, Brazil, South Korea and India. So there was an overall supply deficit of more than 1.2 Mt (1.3 million st). This, combined with an 18.3-percent diminution in closing stocks (down to 35 days of requirement), lifted the average spot price of MGA by 17.6 percent year-on-year to US$448/t (US$406/st).

Jan 1, 2006

By Phillip M. Busch

VANADIUM was discovered in 1801 by Andres Manuel del Rio, a professor of mineralogy at the School of Mines in Mexico City. Del Rio called the new element erythronium. Later, he decided that this was not a new element but a form of chromium. Not until 1831 did Nils G. Sefström, a Swedish chemist, positively determine that the metal was a new element which he named vanadium, after Vanadis, the Scandanavian goddess of beauty. From 1831 to the 1860's and 1870's, the comparative scarcity and high cost of vanadium restricted its commercial use. Shortly after 1870, more information was obtained on the physical and chemical properties of the element. Thereafter, research on vanadium has dealt largely with its use as an alloying element in steel and nonferrous metals. Vanadium is a widely distributed element in the earth's crust. It is more abundant than many metals but is disseminated in small quantities throughout a great variety of rocks. Relatively few deposits have contained ore of a grade suitable to warrant development for vanadium alone. It is produced in conjunction with uranium, iron, titanium, aluminum, and lead-zinc ores.

Jan 1, 1961

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P. Kordi, L. Egorova, R. J. Bowell, D. Gurevich, V. Sedov, A. Mikhailov, D. A. Holwell

ABSTRACT Reconnaissance exploration in the Kuene region Namibia has included geological mapping, soil and stream sediment geochemistry, and ground geophysical methods. Copper mineralization occurs within a well-defined belt with north-northwest to south-southeast trend, parallel to the regional strike of the sedimentary rocks. The occurrences vary in size but are generally stratabound. The mineralization is centred on the transition from calcareous shale and interbedded limestone, through carbonate rocks, to quartzite. Geochemical anomalies have been identified correlating to induced polarization (IP) and magnetic anomalies. The anomalies identify one potential metallogenic zone more than 17 km in strike length.

Jan 1, 2012

By J Rubio

This work presents design features of an innovative in-line mixing helical (coiled) reactor for flocculation and flotation as a solid-liquid separation process for suspended particles (including liquid droplets). The device has been named flocs generator reactor (FGR), a compact system whereby the flocculation of particles is assisted by the kinetic energy transfer from the hydraulic flow through the reactor and/or by the injection of microbubbles (30 - 70 ¦m). The flow mixing presented a plug flow regime with a low dispersion degree, promoting the required hydrodynamic conditions to disperse the polymer flocculant (cationic polyacrylamide) and to generate æstrongÆ flocs of Fe(OH)3 or clays (as colloidal model systems) with aggregation using an anionic polymer, Al2(SO4)3 and poly aluminium chloride (PAC), and oil emulsions destabilisation with a high molecular weight cationic polymer. The solid-liquid separation of the flocs was then achieved either by settling or by flotation with microbubbles. This paper discusses advances in this new in-line flocculation-rapid flotation device to remove æaerated aggregatesÆ, aggregates with entrained and entrapped bubbles. Studies were carried out with different models of FGRs (varying the length:volume ratio) and process efficiency (mainly kinetics) evaluated as a function of polymer concentration and some operating parameters, namely, feed flow-rate, air:solids ratio and residence time. Results showed that the aerated flocs are readily floated with rising rates in the order of 120 mh-1, values higher than those obtained for the settling of the non-aerated flocs (18 - 24 mh-1). The FGR requires short residence times and generates dense, well structured flocs (with a mass fractal dimension, dF of about three) which withstand high shear forces. Mechanisms involved appear to include small bubble formation and their rapid occlusion (entrapment) within flocs, nucleation of bubbles at floc/water interfaces, polymer coiling as a result of æsalting outÆ effects at the aqueous/air interface and plug flow type of mixing (flocculation). Successful examples of emulsified oil and solids removal from water are shown and because in all cases high efficiencies were obtained (>90 per cent removal). Due to the high process efficiency and high loading capacity shown, the FGR appears to have good potential as an in-line flotation-separator device in applications requiring high rate solid-liquid or liquid-liquid separations.

Jan 1, 2005

By D. L. Yopps

In research conducted by the U.S. Bureau of Mines, platinum-group metal (PGM) flotation concentrate from the Stillwater Complex, MT, was subjected to biooxidation using Thiobacillus ferrooxidans in an effort to break down the sulfide minerals and liberate the associated PGM's for subsequent chemical leaching. Bacterial preleaching oxidized up to 94 pct of the sulfide present, destroyed the PGM-bearing pentlandite [(Ni,Fe)9S8] mineralization, and dissolved most of the nickel in the concentrate. Cyanidation at 80° C proved to be the most attractive chemical leachant, removing 34 pct of the platinum, 76 pct of the palladium, 94 pct of the rhodium, and 97 pct of the gold from the biooxidized concentrate. Research also indicated that increased sulfide oxidation during the preleach phase led to improved PGM recovery in the subsequent chemical leaching phase.

Jan 1, 2010

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

After several years of laboratory and field evaluations, it has been established that each frother has its own unique relationship among bubble size reduction, gas hold-up increase, froth stabilization and frother concentration. It has been shown that a frother?s hydrodynamic properties can be characterized using the relationship between the froth zone property froth height and the pulp zone property gas hold-up. The relationship is established in a bubble column run at a given air rate over a range of frother concentration. The use of relationships in frother selection and plant diagnostics is illustrated in a series of plant case studies.

Jan 1, 2009

By Alfred Bellows

The objective of this contract is to design, build and demonstrate a support system to improve roof control in the entries of longwall mines. The objective of this phase has been the detailed design of such a system and the selection of a test site in which to perform the pilot demonstration. The result is a complete set of detail drawings or specifications which define the three major components of the system. The Gate Support is a variation of a face chock which has an extended canopy and additional hydraulic legs to protect the region of the face-entry intersection. The Entry Support is a steel beam and hydraulic prop set which is reusable and serves to support the first 100 or more feet of entry inby the longwall face. The Transporter is a bolter-like vehicle with a crane used for installing and retreating the beam sets. The test site selected is CF&I's Allen Mine in Colorado. They presently use simi¬lar steel beams and expect the FMA support system to be more effective as well as recoverable. It is recommended that the completed drawings be used to build a prototype system and test it first in a remote section of the mine and then in the active longwall tail entry.

Jan 1, 1978

By J. Budac, J. Dennett, D. Mayne, P. Nawrocki

"The Nickel/Cobalt operation in Fort Saskatchewan, Alberta has successfully used an oxidative ammonia leach process to refine a variety of feeds into high quality nickel and cobalt products for over 60 years. Fundamental changes to the refining process were made when the major feed was converted from nickel concentrate to cobalt rich mixed sulphides in the early 1990s. Since the early 1990s, the production capacity of the refinery has expanded to match increases in both mixed sulphides and other feeds. In addition to increasing the production capacity of the refinery, other changes have been required in order to improve the operability and reliability of the refinery as well as to deal with increasingly stringent safety and environmental requirements. This paper describes recent changes at the refinery including changes to the flow sheet, improvements in unit operations, incorporation of new feeds, management of byproducts, and control of impurities.INTRODUCTION The Cobalt Refinery Company (Corefco) plant in Fort Saskatchewan processes nickel-cobalt mixed sulphide intermediate produced at the lateritic nickel mine and high-pressure acid leach (HPAL) facility in Moa Bay, Cuba. Both operations are jointly owned and operated by Sherritt International and General Niquel of Cuba. The mixed sulphide, along with other feed materials, is processed at the Fort Saskatchewan refinery using a pressure ammonia leach-hydrogen reduction process to produce nickel and cobalt metal. This refinery was originally constructed in 1954 to treat nickel concentrate from Sherritt’s Lynn Lake mine in Manitoba. (Benson and Colvin, 1964; Boldt and Queneau, 1967; Forward, 1953; Forward and Mackiw, 1955; Kerfoot, 1989) From the mid-1970s until the early-1990s, the facility operated as an independent refinery, treating nickel-bearing feeds from around the world. The flowsheet was changed in 1992 to address the increased cobalt content of the feed. (Cordingley and Krentz, 2005; Kerfoot and Cordingley, 1997) The flowsheet was adapted further in 2009 to improve cobalt speciation in the leach process, which allows better cobalt-nickel separation. The 2009 iteration is shown in Figure 1. Three ammonia leach stages were used to ensure high recoveries of nickel and cobalt. Underflow solids from the final leach stage contained mainly iron oxides. One of the features of the leach process is the innovative recycling of ammonia. Ammonia vented from the leach process in tail gas and from atmospheric tanks is recovered and recycled into the refinery using water based scrubbers and a high pressure distillation process. Indeed, roughly 250 t NH3/d is recovered as distillate and recycled back into the process. Also, air enriched with ammonia which is vented from the later first stage autoclaves is recycled to the lead first stage autoclaves to maximize oxygen and ammonia utilization."

Jan 1, 2017

By C. -K. Fang

"Aging effect on the wear resistance of alumina particulate-reinforced 6061 aluminum matrix composites with a block-on-ring wear tester has been investigated. Specimens with various Al2O3 volume fractions of 0%, 10% and 20% were employed in this work. Experimental results indicated that over-aged monolithic 6061 Al had the best wear resistance, as compared with under-aged and peak-aged conditions. For the composite containing 10% Al2O3, over-aging and peak-aging resulted in similar wear resistance, which was higher than that for underaging conditions. For the composite containing a high volume fraction (20%) of Al2O3, the wear resistance reduced with the increase in aging time. Although longer aging time was favourable to the wear resistance of monolithic 6061 Al, it was detrimental to that for the Al2O3/6061 Al composite with high volume fraction of particles. IntroductionMetal-matrix composites (MMCs) have received attention in many engineering applications because of the demands for high specific strength (strength-to-weight ratio) and specific stiffness, good high temperature capabilities and wear resistance. The manufacturing processes of fiber-, whisker-, and particulate-reinforced MMCs have been well developed (Hosking et al., 1982). Because of the reduction in fabrication cost, the applications of MMCs have been widely extended to light weight-bearing sleeves, calipers, automobile parts (brake rotors, drive shafts, connecting rods, piston rings, and cylinder liners), sporting goods, aerospace components, tanks (wheels, speed brakes, and track shoes) and other industrial applications. Among the three types of metal matrix composites, particulate-reinforced MMCs are promising because of their homogeneous and isotropic material properties and low cost. Additionally, they can be formed using conventional metal processing techniques."

Jan 1, 2003

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By V. F. Parry

This report is the first substantial description of the carbonizing process and the details of experimental work conducted at the Denver laboratories under a coopeative agreement between the Bureau of Mines and the Texas Power & Light Co. It presents the results of tests on several Texas lignites and other typical western coals that have been processed in the first pilot plant operated at Denver. Investigations on drying fine coal in the entrained and fluidized state have been under way at Bureau of Mines Denver laboratories for several years. Reports on this work were published in 1949 and 19505/ describing the theory and practice of re-moving inherent moisture from the lower -rank coals. The investigation did not include a study of the removal of surface moisture from fine fuel. Private industry in Canada became interested in the possibilities of drying fine coal, employing the closed-circuit system and techniques recommended by the Bureau. Large, commercial-scale drying units were built by a Canadian company, which successfully demonstrated that surface moisture could be removed from fine coal at high efficiency and capacity ill drying units similar in design to those developed by the Bureau.

Jan 1, 1953

Meeting of June 26, 1914.-The President was authorized to appoint Advisory Committees to co operate with the United States Bureau of Mines. The President announced the appointment of Edward H. Benjamin and W. C. Ralston as additional members of the Committee on Arrangements for the San Francisco meeting, 1915. H. T. Van Ells and Judd Stewart were appointed to represent the Institute on a joint committee of several technical societies to consider the standardization of graphical methods for the presentation of statistics. The President announced the appointment of H. Foster Bain to succeed Edward H. Benjamin, resigned, on the Committee of Management of the International Engineering Congress, 1915. The Secretary was authorized to issue a new circular advertising the sale of back Transactions and to sell back Transactions, bound in cloth, at a price of $35 for 46 volumes, provided sufficient orders were received to warrant the special binding. The sum of $177.50 was contributed to the San Francisco Local Section. Upon recommendation of the Committee on Membership, 70 Members, 4 Associate Members and 7 Junior Members were elected to their respective classes; there was also one change of status from Junior Member to Member.

Jan 8, 1914