Search Documents

By Bengt T. Andersson

Outokumpu Consulting Engineers, Outokumpu Oy SF-02200 Espoo 20, Finland This paper describes experiences from some operating non-ferrous flash -smelters and focuses on the advances in smelter byproduct and gas treatment engineering design. In this context a summary is given of the specific technical and economic benefits achieved-by flash -smelting technology and oxygen enrichment. The paper will also briefly outline a few new process and equipment developments.

Jan 1, 1983

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013

By J. L. Johnson

The U.S. Bureau of Mines investigated the recovery of tin and silver from the Coal Creek deposit in the Talkeetna Mountains, AK. Approximately 5 million st of reserves grading 0.2 pct Sn with silver credits of 0.2 tr oz/st have been delineated by drilling. A 10-to 25-pct Sn gravity concentrate was produced by treating the minus 20-mesh ore with a spiral, then regrinding to minus 65 mesh and tabling. Sulfide contamination in the gravity concentrate was as high as 60 pet. Sulfide flotation of this concentrate produced tailings containing 40 to 50 pet Sn. Overall recovery was 76 pct for tin but only 5 to 10 pct for silver because of losses during sulfide flotation. Other methods tested to clean the concentrate included cassiterite flotation, gangue flotation, nitric acid leaching, and wet and dry magnetic separation. Tin beneficiation tests on the minus 325-mesh fraction included cassiterite flotation, vanning, sulfide flotation, and fuming. The bench-scale and locked-cycle tests were used to estimate the mass flows for a 1,000-st/d plant.

Jan 1, 2010

By T. G. Joseph, K. Barron

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an “apparent friction” concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of triaxial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock. This strain-softening relationship is then applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post-failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

Jan 1, 2003

By A. N. Brown

The Hendrik van der Bijl Memorial Lecture is arranged annually under the auspices of the Pretoria Engineers Liaison Committee. This is a multidisciplinary Committee with representatives from eleven societies and associations, and serves the interests of engineers resident in the Pretoria area. Coal preparation The Japanese Organizing Committee of the 11th International Coal Preparation Congress is now busy making the necessary arrangements for the Congress, which is to be held in Tokyo from 22nd to 26th October, 1990.

Jan 1, 1989

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

By W. D. Ryan

The organic act passed by Congress in 1910 instituting the Bureau of Mines provided that the director of the bureau should promulgate such investigations as might be necessary to determine the causes of mine accidents and the best methods of preventing them. With the object of accident prevention in view, Director Joseph A. Holmes, and others who were pioneers in the bureau, conceived the Plan of having first-aid and mine-rescue training as one of the major activities of the Bureau. Out of this plan grew the first-aid and mine-rescue contests, which have been featured as an incentive for men to take courses in this type of mine safety training. The first appropriation for mine-accident investigations became available on July 1, 1908, under the jurisdiction of the U. S. Geological Survey, with Dr. J. A. Holmes in active charge. During 1908 there had been some first-aid training in the Pennsylvania anthracite field and a start made in Illinois, although there appears to be no exact information as to when or where first-aid training in the mining industry first became a reality, it is generally conceded that the St. John's ambulance corps of Scotland was one of the first - if not the first - to make the work effective. In 1911, to celebrate the establishment of the Bureau of Mines and the formal opening of the Pittsburgh, Pa., station, a first-aid and mine-rescue demonstration was conducted on Forbes Field, Pittsburgh. President William Howard Taft and many other men notable in public life were 2 resent. This was the first general national contest of the kind held it the United States; and since then there have been a number of nation-wide first-aid and mine rescue contests, as well as some which have been international in scope. There are over one hundred first-aid and mine-rescue contests of various kinds held annually in connection with mining and the allied industries.

Jan 1, 1929

By Thomas Sisley, Jozef Zurawski, Richard Switalski

Hilltop Interceptor Contract G is one of the segments of the wastewater control system in the greater Cleveland area. The tunnel is a relief interceptor constructed by the Northeast Ohio Regional Sewer District to minimize combined sewer overflows in the Easterly Service Area. The design study identified the need for a 3.35 m (132 in) diameter, 3.35 km (11,000 ft)in-line storage conveyance tunnel to be constructed at depths of 30 to 70 m (100 to 230 ft).Six structures for access, future flow drop, work shafts and overflow control were required to complete the system. The interceptor reduced the design peak flow from 12.5 m3/s(285 mgd) to 6.1 m3/s (140 mgd) by detaining in line 22,800 m3 (six million gallons) of wastewater.

Jan 1, 1997

By Demosthenes (Dennis) Efstratiadis

After European Council’s Directive 93/15/EEC of 5 April 1993 on the harmonization of the provisions relating to the placing on the market and supervision of explosives for civil uses, the so called ”Intra-Community Transfer of Civil Explosives” has been possible between users in the member States of the European Union. In line with this new approach, the placing on the market and the supervision of explosives for civilian use are subject to essential safety requirements. The explosives market in Italy is regulated by the ”day consumption of explosives” that imposes the user to have on site just the strict quantities of explosives and accessories that are necessary for the daily drill and blast activities. Any eventually advanced explosives’ quantities should be destroyed, either returned to the provider’s magazine until the 24:00 hours of the same day.

Jan 1, 2018

By Amilton Feliciano Castro

In this work, activated carbons (ACs) were prepared using Sewage sludge as starting material. The ACs were pyrolyzed in an inert atmosphere at 550 °C after independent chemical treatment with ZnCl2 or KOH with ratio of 1:1. The materials were used as adsorbents for removal of Cu(II) from aqueous solutions. The adsorbents were characterized using adsorption/desorption nitrogen isotherm, SEM (scanning electron microscopy). The results showed that copper removal could be linked to surface pH and compounds present on the surface of adsorbent. KOH-treated adsorbent has smaller surface area (186 m2 g-1) than ZnCl2-treated adsorbent (192 m2 g-1), however, KOH-treated adsorbent exhibited higher removal of Cu(II). The performance of KOH-treated adsorbent could be attributed to the presence of basic groups on the adsorbent surface. Liu isotherm model gave the best description of the equilibrium data. From the Liu isotherm, the maximum adsorption capacities at 298 K for KOH-treated, ZnCl2-treated and sewage sludge (without inorganic activation) adsorbents are 31.85, 19.79 and 3.513 mg g-1, respectively. The best desorption experiment was obtained using 1.50 mol L-1 of HNO3 as eluent. Recoveries of Cu(II) from Cu(II)-loaded adsorbents are 98.9% (ZnCl2-treated) and 95.5% (KOH-treated.

Aug 17, 2017

By Filippo Maria Leoni, Wesley Schmutzler, Matteo Bertoni

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project (Project) in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 92 inch ID forced sewer main relocation and to improve the soils for the base of a new drainage channel. The soils to be improved consisted of sandy fill, soft clays, organics and stiff, plastic clays. A pre-construction soil investigation campaign, followed by a Bench Scale Mixing Programme and a Full Scale Field Test were performed during the pre-construction stage to assess soil properties, select binder type and dosage, and disclose the most suitable combination of injection parameters to improve the different soil layers. Production started at the end of August 2012 and was completed in October 2013; over 3,000 DMM elements were installed to a maximum depth of 57 ft below ground for a total gross volume of approximately 125,000 cubic yard. Each element consisted of two 5.5 ft diameter overlapping columns installed simultaneously, and their layout was such to meet the 100% Area Replacement Ratio required by the design. The ground improvement was successfully completed despite some difficulties due to a considerable amount of obstructions. Wet grab sampling and UCS testing of the retrieved specimens were designed as the main QC/QA method for the verification of the quality of the ground improvement. Upon completion of production, approximately 3,000 specimens were cast. The contract also required continuous coring of at least 12 randomly selected DMM elements and the testing of 8 cored specimens per bore for strength assessment. This paper will illustrate means and methods used in the field to construct the designed ground improvement and the results of the QC/QA program, with a focus on the differences between wet grab and coring sampling methods.INTRODUCTIONThe Rio Puerto Nuevo project involved the stabilization of a major drainage channel using the Deep Mixing Method (DMM), and the relocation of a 92 inch ID forced main sanitary sewer outfall. Previously, in 2004, a 40 x 16 x 2,000 ft. box culvert was installed under a different contract to convey runoff waters to the ocean.However, the connection between this culvert and the upstream network of channels was not constructed due to the presence of the forced main sewer pipe. In order for the drainage system to be completed and function properly, the 92 inch ID forced main needed to be lowered about 20 ft to allow for proper drainage.DMM was chosen by the US Army Corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The DMM was arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for Zone A (deeper and with a higher strength requirement) and Zone B as an example (Figure 1)."

Jan 1, 2015

By Joel Werner

Weak metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as: remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

May 1, 2003

By M. Akser, M. Tomas

Six Sigma is a methodology that uses a structured and disciplined approach to improve process performance (higher throughput, better recovery, lower cost, shorter cycle time, etc.). Specially trained people called “black belts” lead and manage Six Sigma projects. Black belts, with assistance from their team, ensure that projects follow the DMAIC (define, measure, analyze, implement and control) process phases. Timely completion of each project, with measurable deliverables, is key to Six Sigma’s significant financial success. Implementation of Six Sigma has been growing in recent years in a wide range of industries. The heavy mineral industry, like many other industries, could benefit from what Six Sigma has to offer. Specific Six Sigma project examples are included from DuPont’s Heavy Mineral Production Plant in Florida.

Jan 1, 2005

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the sixth. The data are accompanied by maps showing the loca.ion of holes, drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test geophysical anomalies. The locations of those holes are shown on figure 13 in Volume I. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion-type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-showing low, erratic methane readings.

Jan 1, 1966

By Sami Kara, Yunseok Park, Seung-Joong Lee, Namsun Hwang, Michael Laing

This study conducts a comparative analysis of construction efficiency. In the first part we compared electronic and non-electric initiation systems, focusing on tunnel contour holes. Field blasting operations were executed across a variety of delays to identify the optimal delay time. This delay for the in-situ rock mass was determined through regression analysis of blasting vibration in contour holes and for overbreak/underbreak. The blasting results with the electronic initiation system using the obtained optimal delay, applied to contour holes, were compared with the results of the non-electric initiation system. The overbreak and underbreak decreased by an average of 2.7 cm and 5.8 cm respectively, by using the electronic initiation system. Moreover, the vibration reduction rate in contour holes region was reduced by 11.9% based on the blasting vibration estimation equation proposed by the Ministry of Land, Infrastructure, and Transport (MOLIT). Underground construction projects have become increasing popular as cities grow in both size and density. This growth severely limits the amount of useable space for new project on the surface, resulting in the decision to build them underground. This new policy however brings into focus the challenge of managing and reducing blasting related vibration due to the proximity of these projects to sensitive structures, utilities and foundations often present in urban environments. For this purpose, we have been required to manage the vibration by reducing the quantity of explosives used per round. Inspired by surface blasting techniques, we applied a decking mode to address and work around this challenge. We present in this paper the first attempt to blast a tunnel face using a decking method and reduce the charging per hole from 6 kg to 3 kg per hole and keep the same advance rate for this tunnel. The results are presented in the third part of this paper. In the second part we present the results of the decking mode in shaft. The use of the electronic initiation system in tunnel construction provides the users an effective tool to improve the overbreak/underbreak and keep the vibration at a low level with a large gain on the overall project schedule and budget. This what we want to demonstrate in this paper.

Jan 21, 2025

By P. L. Dunn

Automatic control of fine coal cleaning circuits has traditionally been limited by a lack of sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for on-line determination of ash content in fine coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73 ± 4% ash over a range from 65-90% ash. While this result is comparable to existing nuclear-based analyzers, the video-based system is only a fraction of the cost. The sensor is currently installed at the Middle Fork preparation plant owned by Pittston Coal Company.

Jan 1, 1997

By R. M. BUCHANAN

The segment of Canadian industry based on smelting of alum in um and manufacture of consumer products is based entirely on imported alumina and bauxite. In the absence of Canadian bauxite deposits, consideration of anorthosite, a less desirable aluminous rock, is being undertaken as one alternative in maintaining assurance of supply. Anorthosites in Canada cover many thousands of square kilometres of the Precambrian Shield. Although compositions vary widely among Canadian anorthosites, many appear to exceed the specified minimum of 25% A I 20 3 in bodies containing more than the required JOO million tonnes. A lthough most Canadian anorthosites are of Precambrian age, one located in British Columbia has been identified as being Middle _Cretaceous.

Jan 1, 1984

By N. Kumar Kittusamy