Search Documents

Low Zinc Prices Close Alcoa Mine Alcoa Mining Co., announced that it will suspend operations at its Hutson mine, near Salem, Ky., because of low zinc prices, January 15. The Aluminum Co. of America subsidiary announced that the low market has made zinc mining un- profitable. About 70 men were employed at the mine, with a production of about 5000 tons of zinc annually. Alcoa said the shutdown would not affect other company operations, with most of the men at Hutson absorbed in the mining firm's fluorspar operations in the same area.

Jan 2, 1953

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By H Hutchinson

Froth flotation is applied to mineral sand concentrates in order to produce commercially viable xenotime concentrates. Experiments indicate that a xenotime product containing 38% Y2O3 at 47% recovery or 34% Y2O3 at 83% recovery can be obtained from a 27% Y2O3 feed. The process involves a primary stage of reverse flotation at which oxide and silicate gangue is floated, and secondary stage of direct flotation at which xenotime is floated. Of the various collectors screened an amphoteric compound was found to be effective at both stages. This was made possible by the addition of sodium silicate at the second stage, which acted as depressant for the remainder of the gangue. Similar studies on a low grade feed material were somewhat unsatisfactory as the grade achieved fell short of what was targeted.

Jan 1, 1990

During the period 1979 thru 1982. Multi Mineral Corporation conducted a mining research program at the United StAtes Department of the Interior's Bureau vi Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). ? Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Jan 1, 2008

By He De-wen

Based on the principle of life cycle assessment (LCA), municipal solid waste management (MSWM) was analyzed by life cycle inventory method. According to the system expansion and substitution method, the content and frame of life cycle analysis is summarized and applied to municipal solid waste. On the basic of feasibility research of life cycle analysis on MSWM, the paper put forwards complete and concrete ?three changes? measures under life cycle analysis on MSWM. Some aims of MSWM can be achieved under above conditions of LCA on MSWM: to improve the current system efficiency of MSWM; to enhance the serve quality of MSWM, to increase recycle garbage from MSW; to reduce waste amount and reach minimization and innocuity aim of MSWM; to help the departments of MSWM to get over all difficulties to realize their ideal goals.

Jan 1, 2009

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

By Lee Browne

The transformation of Peru’s Tintaya copper project from a state-owned company to a private company is under way and the results have been successful. Since Magma Copper Co. assumed operating management in December 1994, production and costs have improved dramatically. To understand the transformation of Tintaya, the transformation of Magma Copper must also be understood.

Jan 1, 1996

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

Kinetics of Reclamation of E-Waste by a Bioleaching Route

Sep 13, 2010

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

By Zhigang Liang

A carbon free precast block was prepared by using high-alumina fused corundum as aggregate and fused magnesia, and ultra-fine Al2O3 and ultra-fine SiO2 powders as matrix materials. A small linear expansion for the precast block was achieved through spinel formation from the reaction of MgO with Al2O3. The precast block showed a lower apparent porosity, higher hot modulus of rupture and better slag corrosion resistance compared to the traditional Al2O3-MgO-C brick. Moreover, the practical application of the precast block to the ladle lining proved it to possess a better thermal insulation which could effectively prevent the temperature drop of molten steel during the refining process. It can be predicted that the carbon free precast block could possibly be accepted as a new type of ladle lining material for the production of low-carbon and ultra-low-carbon steel.

Jan 1, 2009

By C. H. Fisher, M. L. Fein, A. Eisner, G. C. Sprunk, Loyal Clarke, H. H. Storch

"The large reserves of low-rank coals in the western United States are at a disadvantage in competing with the more mature but less plentiful eastern coals, which are nearer important markets and are more suitable for combustion and coke production. However, low-rank coals generally are amenable to hydrogenation, and the western coals might become an important source of liquid fuels and organic chemicals when petroleum is less plentiful.In view of these facts an the tremendous quantities available, further information on the western coals clearly desirable. The purpose of the work described in this paper was to study the hydrogenation characteristics of some of the low-rank western coals in discontinuous converters. The data obtained in this manner, which are inadequate for predicting the suitability of coals for large-scale continuous hydrogenation, were used as a basis for selecting samples for further study in the Bureau's experimental coal-hydrogenation plant (26, 35). 8/ Because of the general importance of the western coals and recently demonstrated relation between coal hydrogenation and petrograghy (14, 15, 16), the proportions of anthraxylon, (vitrain), translucent attritus, and opaque matter were determined. In some instances samples of anthraxylon were isolated and hydrogenated separately so that their properties might be compared with those of the entire coal. The samples studied include peat, brown coal, lignite, sub-bituminous coals, and low-rank bituminous coals."

Mar 1, 1940

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By Gordon M. Matheson, David K. Miller

Possible impacts to the water quality and production capacity of ground water supply wells by blasting is a common cause of complaints for blasting contractors, mining companies, and local regulatory authorities. The major complaints of changes in well water quality include; turbidity, discolored water (red, brown, black, yellow and milky water), and nitrate and/or coliform contamination. The major complaints for changes in well water production capacity include: loss of quantity production, air in water and/or water lines, damage to pump, and damage to well screen or borehole.

Jan 1, 1997

By Hugh Douglas

In the past two years recent increases in silver prices over levels that prevailed for many years have changed supply/demand patterns. On the supply side, a silver mining boom is in progress in the United States and elsewhere. On the demand side, traditional uses of silver by individuals are dropping while industry is conserving. These changes will alter the supply/demand balance and bring about more moderate rises in silver prices, which in turn will impact the mining industry.

Jan 1, 1981

By Kevin M. Connor, Malcolm J. McPhersqn

Examples are presented in which Time Domain Reflectometry (TDR) was employed to locate deformation of rock masses induced by mining. The first example involved motoring the propagation of overburden fractures above a longwall coal panel and the second example involved the we of a)R to monitor rock mass deformation in the vicinity of a strip mine highwall. Bock mass deformation, strata separation and large block movement generated strains and failure along coaxial cables which were installed in drill holes and the TDR reflections generated by these strains and failures were monitored. Analysis of field data and a preliminary laboratory test indicate that it may be possible not only to locate rock mass movements but also to quantify these movements with TDR data.

Jan 1, 1984

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014