Search Documents

By A. Erdem

In this study, approximately 3 tons of coal sample taken from thickener entrance was prepared by mineral processing techniques and cleaned by gravity methods. The samples were classified to 5 size fractions by wet screening. The size fractions of +1mm and -1 +0.500 mm were chosen for direct consumption or cleaning by spirals. The studies by Multi Gravity Separator (MGS) were carried out with the -0.500 +0.280 mm and -0.280 +0.020 mm size fractions where the -0.020 mm fraction does not used in the experiments. The clean coal fractions of +1 mm and -1 +0.500 mm obtained by classification were subjected to lower calorific value (LCV), ash and total sulphur analyses. The results were 4168-4946 kcal/kg (on dry basis), 31.01-38.54 % ash and 4-4.27 % total sulphur content respectively. The results of the clean coal concentrated by MGS experiments in -0.500 +0.280 mm fraction was found 5918 kcal/kg LCV, 19.82 % ash content and 80.47 % combustible recovery. The results for the -0.280 +0.020mm fraction were 6004 kcal/kg LCV, 19.19 % ash content, 80.47 % combustible recovery respectively. With reference to the above experimental results, pre-economic evaluation studies were completed and decided to construct an additional unit to the plant. Capacity of the constructed unit is 75.000 t/y which corresponds $ 2.600.000 income in a year. General Directorate of Turkish Coal Enterprises concluded to apply this project to the other coal washing plants in the country due to the successful results of this study and laboratory studies has been going on by MTA currently. Keywords: coal tailings, mgs, recovery, washery, pre-economic evaluation

Sep 1, 2012

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By S. K. Nicol

Flotation, water-washing cyclones (hydrocyclones) and spiral concentrators are the three process units most commonly utilised in fine coal preparation. The results of testwork conducted on these three units will be presented and their performance and separation characteristics examined in detail. In particular, the dependence of the separation characteristics of each unit on particle size and the constraint this places on product quality (ash and sulphur levels) will be discussed. This dependence will be shown to be a critical criterion in the selection of fine coal circuits.

Jan 1, 1986

By D. C. Hatch

At the MacIntyre Development of the Titanium Division of National Lead Company a magnetite-ilmenite ore together with gabbro-anorthosite waste is mined from an open pit by shovels and trucks. The ore from the pits is trucked to ore stockpiles for blending ahead of the crusher and to free the mine from crusher delivery schedules. The ore stockpiles are blended to yield a 16.5 to 17.0 % TiO, crusher feed. This requires mining on an assay cut-off rather than a visual grade cut-off. Highly mineralized ore runs from 20 plus % TiO2 and 30 plus % Fe to 15 % TiO2 and 40 plus % Fe as the ratio of ilmenite to magnetite changes. There are three major ore types in the present pit with magnetite ratios varying from about one to one up to three times as much magnetite as ilmenite. Ilmenite and magnetite together liberate from gangue down to about 10 mesh and this is the basis of the magnetic cobbing. Below 10 mesh the ilmenite and magnetite start to separate and ore cobbing pulleys will not hold the ilmenite.

Jan 1, 1968

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By G. Davey

High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. The operating experience of two existing copper operations will be covered to show the effect of the introduction of the Metso Stirred Media Detritor (SMD) a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from the introduction of this new technology. The benefits and process difficulties are covered and explained.

Jan 1, 2003

By E. W. Davis

I . OPERATING TESTS 1. CHARACTER OF ORE UNDER INVESTIGATION On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite . The magnetite comprises about 35 per cent. of the rock. Fig.. 1 show&apos;s graphically that the tonnage of minus 200-mesh material produced varies directly with the tonnage fed to the mill. There is undoubtedly some limit to this relation, but there seems to be no indication of it at 18 T. per hr. Some of the conclusions drawn from this test are that: (a) The ball-mill is naturally a machine of very large capacity; (b) if it is not possible to deliver a large tonnage of original feed to the mill, a closed circuit should be provided so that the mill may crush its own oversize.

Jan 2, 1919

By J. F. Myers, F. M. Lewis

THE crushing of ore, as defined by Taggart,1 is "usually a stage process, utilizing . . . machines especially suitable for the reduction of particular sizes... . down to a final stage, employed for the reduction of the finest sizes. . .. In contradistinction, comminution to 20-mesh or finer is called grinding. There is a twilight zone in which the product is 6, 10, or 14mesh limiting size which is either crushing or grinding. . .. " Since the data in this paper pertain to a rod-mill operation, comminuting a particular ore size of ¾ in. to a final stage, coarser than 20-mesh, the rod mill is designated as a "fine crusher machine" in this paper. The published literature discloses a wealth of data regarding a rod mill as a fine-grinding machine but relatively little as a fine-crushing operation. Typical of the latter operation is: (I) a description by F. J. Tuck2 in which a fine-crushing rod mill replaced crushing rolls and (2) a description by the present authors3 in which a fine-crushing rod mill was installed instead of a conventional fine-crushing machine. The experience of the authors is that a definite distinction must be made between the rod mill functioning as a fine crusher and as a fine-grinding machine. As a fine-crushing machine it prepares * relatively large amounts of ore for a subsequent fine-grinding operation; as a grinding machine, it grinds relatively small amounts of ore to some predetermined finished product. PULP MOVEMENT AND ACTION IN MILL In considering the work performed by a fine-crushing rod mill, it seems important to understand just what takes place within the mill. We were inspired to study this matter by a paper by E. W. Davis,4 which indicated that definite water classification of ore particles took place in a ball mill. However, in thinking of the rod-mill action from this point of view, we were confronted with the fact that our rod-mill discharge product showed no evidence of action by water classification. The Tennessee Copper Co. ore is relatively high in sulphides, and the gangue rock and the sulphides are of about the same hardness. In the presence of any action by classification, the coarser sizes are definitely very lean in sulphide minerals. [ ]

Jan 1, 1946

By Donald R. Rathburn

Screening during the production of high-grade lump ore for blast furnace burden, particularly from recently developed ore deposits in Australia, South America, and Africa, has resulted in large tonnages of fine iron ore. Certain owners have decided to stockpile these fines until some later date; however, others have either sold these fines "as is" for agglomeration at the steel plant or have established their own pelletizing plants to produce a premium quality agglomerate. Normally these fines consist of the higher oxides of iron and the hydrated oxides. Unfortunately, grinding these types of materials in a wet process produces a slurry that is difficult to filter to obtain the requisite moisture level for the subsequent balling and indurating operations. The purpose of this paper is to review recent developments in fine dry grinding of iron ore and to discuss the various design and operating parameters involved. Although dry grinding of raw feed and clinker has been practiced in the cement industry for many decades, its significant application to the iron ore industry has taken place within the past ten years. Even though the basic concept of dry grinding has been borrowed from the cement industry, the successful application to iron ore grinding has not taken place without some difficulties. Consequently, the application to iron ore has required the solution of several unique design and operating problems.

Jan 1, 1970

By C. Kelley

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings as fine as 75 microns and coarser have been used. In dry screening operations these same urethane screen surfaces have been relegated to only the coarser separation ranging from 1.0 mm and larger. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies, which allow an end user to consider urethane screen surfaces for dry screening operations where separations as fine as 75 microns are required. These technologies allow an end user to realize the inherent advantages of urethane in wear resistance while also realizing the benefits that a high open area urethane screen surface can bring. These benefits include non-blinding characteristics and feed capacities, which rival that of traditional stainless-steel woven wire mesh screen surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines in conjunction with which they are used. There will also be a presentation of several case studies of commercial installations where these technologies are utilized. These case studies are from the mineral sands industry; therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints, which must be taken into account when considering urethane screen surfaces such as temperature and chemical attack. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By Franz Simon

Conventional fine gold electrolytes for barrel applications working electrolytically actually permit significant precious metal savings by corresponding optimizations but the most gold is still deposited on areas of the components where it is not absolutely essential for the desired bonding and soldering applications, i.e. in high current density areas. Therefore an electrolyte working electrolessly has been developed which inevitably leads to a much more uniform thickness distribution since in an electroless process there are no areas favoured by metal deposition and current distribution. The new electrolyte will be presented and its performance will be compared with conventional electrolytes as regards thickness distribution. The potential gold savings will be discussed.

Oct 1, 2003

By J. D. Miller

Pilot-scale tests indicate that effec¬tive concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% minus 400 mesh and 0.01 opt*) from gravity concen¬tration were processed with a 5-cm air-sparged hydrocyclone (capacity -1.0 tph dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75.0%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1985

By Thomas J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank-run gravels averages about 0.1 grams per ton (about $1.45 per ton), based upon $14.47/g (345O/ounce) gold. Tine Reichert cone, in conjunction with a conventional shaking table, re- covers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1% is -i4 microns (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1981

By L. F. Mashburn, T. J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank- run gravels averages about 0.1 g/t-about $1.29/t, based upon $12.86/g ($400 per oz) gold. The fineness of the gold averages between 950 and 960. The Reichert cone, in conjunction with a conventional shaking table, recovers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1 % is - 74pm (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1983

By R. H. Mozley

It is not my intention in this paper to review recent developments in the mineral processing industry which might fall under the above heading, but to refer to some of the research that I have done over the past 25 years or so. To begin with then, my student days at the Camborne School of Mines, the year 1952. Equipment from the last century was still in everyday use at the local tin mines. At South Crofty Ltd a steam beam engine 100 years old was pumping mine water from 2000 feet, the motive force being conveyed from surface to the pump at the bottom of the mine by a 14 inch square pitch pine rod joined with forged iron straps, steam winders were still in use, and in the mills, stamps ground the ore, and the cassiterite was recovered by equipment with exotic names like "buddies, kievs, and round frames." And to equip us students for the brave new world, we included in our practical mineral dressing a day&apos;s test programme with a Californian stamp -- experience that I am still waiting to put to good use!

Jan 1, 1984

Fine Gravity Separation in the Reflux Classifier, Exploiting a High Shear Rate, Laminar Flow Mechanism The Reflux Classifier is used in the gravity separation of particles over a broad range of particle sizes. The device consists of a fluidised bed zone, with a system of parallel inclined channels above. The inclined channels provide a significant hydraulic advantage over conventional fluidised beds via the so-called Boycott Effect (Boycott, 1920). This paper describes a new advance in fine gravity separation based on the high shear rate and laminar flow profile that arises when closely spaced inclined channels are deployed. As reported recently (Galvin et al, 2009a), a powerful density based separation mechanism develops from this arrangement, suppressing the effects of particle size. In this paper we focus on two areas, firstly the application of the separator in the laboratory for batch fractionation of particles of varying size and density to determine the grade recovery curve and hence the liberation, and secondly the step change in separation performance achieved on a continuous steady state basis when closely spaced inclined channels are used. The variation in the separation density with particle size decreases significantly, and the Ecarte Probable Error (Ep) remains at low levels over a broad size range.

Sep 13, 2010

By Walter Nummela

This acronym may be readily deciphered, and it represents the programming theme for the SME Sessions at the Centennial Meeting of AIME in New York in 1971. The Concentration Committee thus charged out to grab, to induce, and to accept volunteered papers within that framework. The program for the Concentration sessions is in and hopefully all deadlines will be met as specified in the instructions to authors. Without spelling out what is to be seen and heard in New York, how well did the Committee satisfy the theme described in the title? Perhaps it was by virtue of the international makeup of the Committee (Member Dan Pickett is with the Mines Branch in Ottawa) that an international slate of authors was assured. Four countries are to be represented-Bolivia, Canada, Italy, and the United States.

Jan 1, 1970

By Burt C. Mariacher

Two AIME sponsored symposia to be held during the year 1970 will examine copper, lead and zinc metallurgy in considerable depth. MBD and the Extractive Metallurgy Division of The Metallurgical Society will participate in both. Thus, the full field of minerals and metals processing including milling, smelting, and refining will be covered. Since these symposia hold special interest to MBD members, it was felt that a useful purpose could be served by devoting this column to a description of what has been arranged for the registrants.

Jan 1, 1970

By Jan D. Miller

Under the name given to this column, I almost feel obliged to write about some aspect of grinding, but I have decided instead to comment on the future of chemical processing. In recent years, I have seen a tremendous interest in extractive metallurgy develop among undergraduate and graduate students at the University of Utah. For example, of the 12 graduating seniors this year, over half seem to prefer extractive metallurgy to physical metallurgy. In particular, they seem to be most interested in hydrometallurgy, or chemical processing, obtaining industrial exposure to the phenomena they study via part-time employment at the Kennecott Research Center and the USBM Metallurgical Center in Salt Lake City. The stimulus has been generated by society itself. Many students are dedicated to the proposition that new technology can circumvent the destruction of our environment, a concept which provides considerable motivation. At the governmental level, the recent concern for the quality of our environment has created action in the area of chemical processing both through imposition of stringent air and water quality standards, and through increased funding for technological research in this area. The National Academy of Sciences (NAS) gave impetus to this movement when it pointed up the need for development and support of such disciplines as extractive metallurgy, particularly chemical processing, in a recent report on Mineral Science and Technology. The recommendations in the NAS report have prompted governmental action on many fronts, including the Bureau of Mines, and have also given rise to direct legislation in the form of two bills -H. R. 3492 and S. 635- presently before Congress to a mineral engineering education. The report recommends that chemical processing technology (more generally extractive metallurgy) be developed by both new engineering techniques and unconventional chemical techniques such as application of the chemistry of nonaqueous liquids to mineral systems.

Jan 1, 1971