Search Documents

By W. Kemp Wait

Electronic ore sorting has been in use for over 15 years at many mining operations worldwide. Photometric ore sorting, which operates on the basis of measuring light reflectance levels of a rock surface, is in use at various locations on ores such as limestone, magnesite, gold, talc, spodumene, tungsten and coal. Radiometric sorters have been employed on uranium deposits in the western U.S.A. as well as at certain South African go1 d mines where preconcentrating gold is achieved using uranium association as a detector. A new ore sorter, employing two sensing parameters has been developed. Utilizing both photometric and conductivity sensing modes, this system has application to many gold ore types of North America. The first production machine has been installed at a gold mine near Beardmore, Ontario for the purpose of preconcentrating ore both from waste dumps from past production as well as within the ongoing mining operation.

Jan 1, 1987

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of' motors, and motor and equipment bearings. With today's digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system's performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By A. G. Jackson, Mark D. Benedict, Steven R. LeClair, Yang Cao, David M. Conrad

"Electronic Prototyping (EP) represents a new and powerful medium that many in science and technology view as the research paradigm of the future. Actually, EP has many handles, sometimes referred to as simulation-based design involving more long term objectives such as virtual reality, but regardless of the 'spin', the direction of EP is an enhanced visual paradigm to enable a new set of tools for engineers and scientists alike. Tools to not only automate, visualize and compute otherwise intractable problems but to enable augmentations of our ability to perceive that which is interesting and new -""a virtual version of a process"" [1] prodding us on the pathways of materials and process discovery.IntroductionActually there are many reasons to apply sensors to materials, such as smart or adaptive materials/structures, and new materials synthesis/processing [1], only some of which are motivated by improved product quality and/or productivity. Although U.S. Air Force applications of sensors to materials processing represent but one of many perspectives, hopefully it is a perspective which will engender new ideas and insights in addressing future challenges in materials research. To provide context and establish need for future sensor applications in materials processing, we will utilize on one of several Air Force vistas or '21st-Century' objectives."

Jan 1, 1997

By Michael Olmsted

Inspection of boreholes prior to blasting can result in cost reductions as well as increases in efficiency and safety. Until recently, borehole inspection was performed in two manners. For simple inspections, a flashlight was used to view the upper part of the hole. More thorough inspections were performed with long tool strings developed for oil field applications. Borehole inspection tools developed specifically for mining and blasting applications have now been developed. Video Cameras developed for borehole inspection have been in service for several years. Now measurement tools are available, developed specifically for mining.

Jan 1, 2000

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt.

Jan 1, 1950

By S. G. Hardcastle, K. C. Butler, M. G. Grenier

The most common method of determining airflow employed by mine ventilation engineers is the product of i) the average air velocity as measured by a vane anemometer and stopwatch through a continuous traversing technique, with ii) the cross-sectional area of the roadway. This method requires the vane anemometer to accumulate the total flow over the duration of the traverse. Historically, this has been facilitated by a mechanical analog instrument that has either a counter or set of dials that display the flow. Common instruments of this type are Airflow Development's AM5000, Davis's, or Taylor's Biram type anemometer. The AM5000 is widely used in the Canadian mining industry but is no longer available. Therefore, regulatory authorities have seen fit to evaluate presently available commercial instruments to replace the AM5000. This paper describes an instrument evaluation contracted by the Atomic Energy Control Board of Canada which regulates the uranium industry. Over the last two decades there have been numerous advances in the development of electronic air velocity meters. Currently available units have the following features: a) battery operation; b) are compact and can be hand-held; c) employ LCD's, and microelectronic circuitry; and d) provide a time integration for the duration of a traverse. These features make such instruments a possible replacement to the analog units and stopwatch determinations. This paper details five of the new generation of vane anemometers plus a vortex air meter, and it explores their limitations in comparison to analog units. Specific consideration is given to linear response, the effects of yaw, traversing speeds and ergonomics relating to both handling and use. The paper concludes with some features that are attractive and should be considered when purchasing a new anemometer.

Jan 1, 1991

By Uday Pal

In direct reduction processes for iron and steel making, significant amounts of Fe-C alloy droplets are generated and these remain suspended in relatively low FeO (around 5%) containing slags. Earlier workers have found that when the FeO content in the slag is <5%, the decarburization reaction becomes extremely slow (virtually ceases to occur) even though the alloy droplet contains a significant amount of carbons (2-3%). Understanding this rate controlling kinetic phenomena is crucial to designing an&apos; optimum direct steel making process. We studied decarburization of Fe-C particles by low FeO (<5%) containing CaO-SiO2A12O3 slags and found that by putting both the droplet and the slag in direct contact with an inert electronically conductive member that extends deep inside the slag bulk were able to quickly and completely decarburize the droplets. A detailed description and an explanation of the process will be presented.

Jan 1, 1995

By William Hume-Rothery

MR. CHAIRMAN, LADIES AND GENTLEMEN: I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. SOLID SOLUTION At the beginning of our period, the first steps in X-ray crystal analysis had been taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By L. A. Morley, W. T. Parry

Engineering design problems encountered by mining engineers often depend on the properties of natural granular materials such as soil, poorly consolidated sediment, fault gouge, and hydrothermally produced clay. The physical properties of such granular materials frequently are determined by the properties of silicate clays. In most mining applications, the clays are in contact with water. Swelling of clay due to water infiltration can interfere with underground support and haulage systems. Water-saturated clay on fault, fracture, and bedding planes causes slope failures in open pit mines, roof falls and heaving of weak underclays in coal mines. Water may be removed and cementing agents may be produced in clays by electrical methods. When an electrical potential gradient is applied to a charged capillary by two electrodes, water moves toward the negative electrode.1 This electrokinetic phenomena is known as electroosmosis and has been used to successfully dewater clay minerals which lack strength because of water. A consolidation effect occurs when the flow of water is accompanied by a decrease in water content. Electrochemical changes in the clay result in cementing and irreversible hardening. Theory A mathematical basis of electroosmotic phenomena is presented by Helmholtz.3 Smoluchowski5 modifies Helmholtz’ model and presents Eq. 1 to describe fluid flow velocity due to electroosmosis. For this formula, the zeta potential can be measured experimentally. The Helmholtz-Smoluchowski model is reasonably valid for clay aggregates with large pores saturated with fresh water or dilute electrolyte solutions.° An assumption used for Eq. 1 (equations are given Table 1; terms are defined in Table 2) is that the thickness of the electrical double layer surrounding the clay particles is small compared with the pore radii. Because this is generally not the case, Schmid7 presents Eq. 2. The volume charge density in the pore may be approximated from cation exchange capacity and porosity measurements. Casagrande8 offers a semi-empirical relationship (Eq. 3) for volume rate of electroosmotic flow and finds that k, is relatively constant for most clays with an average

Jan 1, 1972

Electroosmotic Dewatering and Consolidation of Mineral Waste Tailings

Sep 13, 2010

By L. A. Morley, W. T. Parry

Laboratory prepared clay-quartz sand samples and fault gouge from an open pit slope undergoing plane-type failure were tested in the laboratory to determine potential mining applications of electroosmotic stabilization and to provide a better understanding of electrochemical hardening. Experiments with very low current densities and free access of electrolytes to both anode and cathode showed an increase in cohesion. Cohesion in a fault gouge increased by 9.3 to 113%, depending on location with respect to the electrodes. For this, power consumption was equivalent to 0.727 watt-hr per cu ft (25.69 watt-hr per cu m). Regions of electrochemical hardening were determined by pH and the anolyte used. Electroosmotic stabilization appears as a reasonable solution to some types of mining problems.

Jan 1, 1975

By Ritchie AS

The principles of chromatographic and electrophoretic separations are described in simple non-mathematical language. Brief details of the analytical procedures and of equipment are given. Partial analyses of rare earth elements in monazites from four localit- ies in New South Wales are compared with analyses from other localities. The presence of uranium in two of the monazites is recorded. The occurrence of rare earths in nature is outlined and its geological significance is indicated, A low capital cost method of analysis of rare earths in monazites is Introduced.

Jan 1, 1972

By George P. Demopoulos, Nima Parsi Benehkohal, Marianna Uceda

Lithium-ion batteries (LIBs) find wide range of applications from portable electronics to electric cars and stationary storage or renewable energy. LIB electrode fabrication is done through mixing the active material (Li-ion host) with carbon (conductive component) and polyvinylidene fluoride (PVDF), which acts as a binder. These components are dissolved in N-methyl-2-pyrrolidone (NMP) to form a paste which is then doctor bladed onto the aluminum current collector. NMP is a toxic chemical and the overall fabrication process remains costly. Efforts are made of eliminating NMP by (1) replacing the binder and (2) using a new fabrication method. Of particular interest among these new methods is electrophoretic deposition (EPD). Via the application of DC potential, particles in suspension can be electrophoretically deposited on different conductive substrates in a relatively fast rate rendering EPD feasible for industrial application. A key aspect for successful application of EPD is the formulation of a stable suspension. Within the McGill HydroMET group, we explore the potential of EPD in fabricating LIB electrodes having demonstrated its effectiveness in the case of P25 nanotitania/carbon anodes. The performance of EPD fabricated TiO2/C electrodes is compared to standard PVDF-based electrodes and shown to have comparable charge capacity. This method is now being extended to other electrode materials. In this paper an introduction to the EPD method will be made and subsequently its use in fabricating LIB electrodes will be described. The performance of the fabricated batteries is evaluated via galvanostatic charging/discharging and cycling tests.

Jan 1, 2016

By R. Herrera-Urbina

Measurements of the electrophoretic mobility of bastnaesite in aqueous solutions of sodium nitrate reveal that the isoelectric point (iep) of this cerium fluocarbonate occurs at about pH 9.3. These results also indicate that the pH affects significantly the electrophoretic mobility of bastnaesite, which becomes more positive as the pH decreases and more negative as the pH increases from the iep. Computations of solid-solution equilibria for the bastnaesite-H2O system closed to the atmosphere as a function of pH indicate that cerium fluoride precipitates in acidic solutions, whereas cerium hydroxide precipitates in alkaline solutions. When the initial amount of bastnaesite is fixed at 0.05 wt.% (the solids concentration used for electrokinetic experiments), these computations reveal that bastnaesite is the only solid phase in the pH range from 5.75 to 8.55, it coexists with CeF3(s) between pH 5.22 and pH 5.74, and with Ce(OH)3(s) between pH 8.56 and pH 10.12. Cerium fluoride and cerium hydroxide are the only solid phase below pH 5.2 and above pH 10.2, respectively. According to these computations, the dissolution-precipitation processes that occur when bastnaesite is equilibrated in aqueous solutions at different pH values determine the solid phases present in the system. In turn, these processes must affect the electrokinetic potential at the solid-solution interface, and they must be considered for explaining electrokinetic measurements as a function of pH when bastnaesite is the original solid phase in aqueous suspensions.

By S. Fawell, H. R. Manouchehri

The main electrophysical properties, i.e., dielectric constant and electrical conductivity, of pure calcite, quartz and wollastonite mineral samples were measured and their triboelectric charge attributes were investigated by contacting minerals particles with different tribochargers made from different materials. In addition the energetic work function values for mineral samples were estimated due to their acquisition charge. Besides, the behaviour of triboelectrically charged of different particle size fractions of mineral samples were inferred. Finally an attempt were made to translate the findings from single mineral systems to a real carbonate ore. The results exposed good prospects to beneficate the examined minerals by triboelectric separation.

Jan 1, 2002

By S. Goto, S. Yamashita, K. Hata

"The average consumption of zinc dust for purification of zinc leaching solution is more than 25 kg per tonne of electrolytic zinc. Authors proposed to remove impurities in zinc leaching solution by electrolysis instead of cementation by zinc dust. The effects of copper and arsenic on electrodeposition of cobalt in zinc sulfate solution were examined fundamentally using a potentiostat. It is observed that cobalt is easily deposited on a cathode at potentials under -480mV with arsenic. Mesh cathodes of stainless steel and lead anodes were used in a small electrolytic cell and the electrolyte was circulated through 'the electrodes during the electrolysis. The effect of electrolyte circulating rate , pH, cell temperature, current density, and concentration of copper and arsenious ions on removal of cobalt were studied. Removal of Cd and Ni are also examined.IntroductionCobalt is difficult to remove from a zinc leaching solution by a simple cementation reaction using zinc dust. However, it is easily precipitated by zinc dust with co-addition of arsenious or stibinous oxide and copper ion in practical operations(I), (2), (3). The consumption of zinc dust for purification is 16-152 kg per tonne of electrolytic zinc and 65% of this zinc dust consumption is used for cobalt purification. The average retention time for purification of cobalt is 4.5 hours (1). A more economical process for purification is desired instead of zinc dust. The mechanism of this acceleration effect of copper and arsenious oxide on removal of cobalt are explained by the authorsas follows; a galvanic cell is formed between zinc dust and copper which is precipitated firstly, and cobalt is reduced on copper as Co-As alloy by this galvanic current(2). This assumption was confirmed in experiments using a galvanic cell with a membrane( 4). The following galvanic reactions occur between zinc dust and copper precipitate; on copper cathode,2H+ + 2e -= Hz(g)2Coz+ + 2HAs02 + 6H ++ 10e -= 2CoAs + 4HzOand on zinc anode,Zn = Zn = 2+ 2e –This galvanic current becomes almost zero in a zinc sulfate solution which includes only cobalt and no arsenious oxide, and cobalt is weakly deposited on a copper cathode. Cobalt deposition requiers a high degree of cathodic polarization. However, the galvanic current flows almost constantly in an electrolyte, which includes arsenious oxide, and the cathode potential is kept at about -500mV. Cobalt is precipitated as Co-As on the cathode.The authors assumed that cobalt may be removed by electrolysis at a very low current density instead of zinc dust and the following experiments were carried out. In the first part of this paper, the fundamental experiments using a potentiostat on the behaviour of cobalt in zinc sulfate solution are described. In the second part, the results of the electrolysis are reported. Cobalt is removed by a new type of an electrolytic cell, which was desigoed to <Iccelerate the rate of deposition of cobalt. The removal of cadmium and nickel in a solution which includes cobalt and arsenic are also examined."

Jan 1, 1997

By Roland Kammel

In combination with various physical and chemical methods also electrochemical techniques are most frequently used to improve the recovery of metals from aqueous dilute process streams or effluents e.g. in electroplating, metal finishing, mining and metallurgical plants. To insure cathodic metal recoveries with favorable current efficiency and high throughputs per unit of cell volume seve¬ral types of electrolysis cells have been developed comprising extended electrode surface areas and/or intensive electrolyte. agitation. The practical experiences with these units indicate especially for the electrolytic recovery of metals whose values are high, that the treatment cost permits profitable operations with relativly short payback periods for the units. Anodic reactions can be utilized for the removal of undesired anion contents or buildups of impurities. Appropriate combinations of these recovery methods are used to improve the versatility and the overall economy. Industrial applications reveal their potentional as addidtive techniques for existing processes to reduce the metal content of effluents to values that meet the guide lines of environmental legislation whereas integrated in-operation recovery methods are nowadays increasingly introduced to approach nearly close-loop operations.

Jan 1, 1992

By Tedd E. Lister, Andre Anderko, Peiming Wang

Mobile electronic devices such as smart phones and tablets are a significant source of valuable metals that should be recycled. Value metals in phones are gold, palladium, silver, copper, cobalt and nickel. Devices now contain increasing amounts of rare earth elements (REE). Effective recycling schemes should include the recovery of these critical materials. Targeted recycling of items containing more of the less available critical materials could address their future criticality. This presentation will describe an electro-hydrometallurgy approach to efficient recycling of metals from scrap mobile electronics. The electrorecycling (ER) process generates oxidizing agents at an anode while reducing dissolved metals at the cathode. Development of the process involved generation of E vs pH diagrams, complemented with metals dissolution experiments used to assess the effectiveness of various solution chemistries. Although several schemes were envisioned, a two stage process has been the focus of work: 1) initial dissolution of Cu, Sn, Ag and magnet materials using Fe+3 generated in acidic sulfate and 2) final dissolution of Pd and Au using Cl2 generated in an HCl solution. Results from laboratory work will be discussed.

Jan 1, 2014

ELECTROREFINING Canadian 1,023,691 -Removal of bismuth from slime filtrate in the Betts process refining of lead. The filtrate is subjected to electrolysis in a cell having an anode of crude lead and a cathode of refined lead under operating conditions to preferentially deposit bismuth on the cathode. The substantially bismuth-free filtrate is recycled for use in the process as the electrolyte for producing high-purity lead. S. Hirakawa and R. Oniwa, assigned to Mitsui Mining & Smelting Co., Ltd. Jan. 3, 1978. 8 pp. (204-73). Filed: 2-18-74 (192,810). Same: U.S. 4,026,776, dated May 31, 1977.

Jan 1, 1979

By . A. C. Atenas

Control of arsenic in the Potrerillos&apos; Refinery electrolyte has been obtained by withdrawing a bleed stream of circulating electrolyte and ensuring the ratio of [O]/[As] in the cast anodes is maintained between 0.9 and 1.0. In order to achieve this control the anode oxygen must be adjusted, depending on the arsenic level in the cast anodes. It has been necessary to modify the time of the reduction step in the anode furnace refining process. Control of this ratio has permitted electro refining of anodes with high levels of arsenic, up to 3000 ppm, while minimizing the volume of electrolyte that must be removed for impurity control so as not to affect the copper concentration in the electrolyte. However this control strategy is not useful when the arsenic concentration in the cast anode is too high, because it is limited by the maximum oxygen concentration allowable for a good quality anodic. Costs have been reduced in anode furnace refining because it is no longer necessary to use alkaline flux injection to remove the arsenic in cast anodes.

Jan 1, 2007