Search Documents

By C. J. Lewis

This presentation concerns calcium oxide-better known as high calcium quick lime High calcium quicklime is produced by calcining high calcium limestone, mostly in the many rotary kilns located throughout the United States and Canada. This paper presents suggestions on the handling of lime based on field experience. The subjects covered are chemical analyses, transporta¬tion, lime storage, lime slaking to form a water slurry of calcium hydroxide solids, slurry transportation, slurry viscosity, and scaling of lime slurries. It is hoped that the comments on the foregoing areas will be of use to those designing or operating lime systems.

Jan 1, 1992

By Sun Ying, Zhang Jing, Li Qiu-ju, Wang Yan-ze

Copper smelter slag was leached using sulphuric acid solutions under atmospheric conditions. Base on the composition and phase of copper slag, the effect of the concentration of sulfuric acid and leaching temperature to the leaching growth rate of Fe, Cu, Co and Ni in the copper slag were investigated in this paper. Simultaneously, the influence of sulfuric acid concentration, leaching time, leaching temperature and the amount of sulfuric acid (solid-liquid ratio) to the leaching rate of these metal elements were researched. Experimental results showed that: with the increasing temperature, the dissolution rates of the metals elements increased first and then decreased. Due to the influence of silica gel which was obtained in beginning of leaching, the higher the concentration of sulfuric acid is not conducive to dissolution of the valuable metal elements. The dissolution degree of Fe, Cu, Co and Ni were 92.83% 96.76% 93.62% and 63.41% respectively.

Jan 1, 2016

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of heptamolybdate ion in aqueous solution appearing in the literature and the absence of its standard pattern, the comparative investigations on Raman spectral pattern of saturated solution of ammonium heptamolybdate tetra hydrate were done. The results showed that the main vibrant frequencies of Raman spectral pattern of the saturated solution were in good agreement with those introduced in the literature, and that the intensity ratio (4.4) of the strongest peak to the second strongest peak recorded in Raman spectrum of the saturated solution had three obvious characteristics: it was greater than each of the results (ranging from 3.7 to 1.3) reported in the literature, much closer to that (4.7) of crystal and well conformed to the change rule of Raman spectra occurring in the process of the first-step polymerization of acidified molybdate solution. It was found that Raman spectrum of heptamolybdate ion in aqueous solution was determined by not only the main vibrant frequencies but also the intensity ratio, which is also the crucial result in this study. The comparative investigations indicate that the pattern of Raman spectrum of the saturated solution is the standard pattern of Raman spectrum of heptamolybdate ion in aqueous solution essentially. The affirmed standard pattern is reliable and can be used to the identification of heptamolybdate ion in aqueous solution, applied in the research of the equilibrium of acidified molybdate solution and the exploration of the best technologic condition for the production of high quality heptamolybdates.

Jan 1, 2006

Steel Ladle in Bhilai Steel Plant, SAIL, India, passes through VAD & LF-RH route and this exposes refractory lining to a severe operating conditions. Ladles are lined with in-house manufactured MgO-C refractories. Lining life used to be 35 heats, out of which 18-20 heats were through VAD/LF-RH, hence, ladle availability had become a constraint. Laboratory studies were carried-out to optimize granulometry and composition. Granulometry was developed by adopting Andearssen packing model. A suitable plasiticiser was identified to eliminate inconsistency caused due to variation in resin quality and weather condition. It reduced variation in green bulk density from 6 to 1.3%. Abrasion and slag erosion studies were conducted, which shows that with increase of carbon, abrasion resistance decreases and corrosion resistance improves. Based on these studies, graphite in slag zone was increased from 10 to 12.5% and in metal zone it was reduced to 7.5%. Different process parameters of brick making were optimized to make MgO-C bricks of maximum bulk density with reduced coke porosity. Modified bricks have bulk density of 2.99-3.02 g/cc and coke porosity of 9.5-10.5%. Further, shape of the bricks were changed from side arch to mini keys and thickness was increased from 80 to 100 mm. Mini key bricks are pressed from sides, thus eliminating variation in thickness which is critical dimension for dry joints. These modifications improved average lining life of steel ladles to 64 heats, which includes 37-40 secondary heats. Maximum life obtained is 87 heats.

Jan 1, 2006

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By Mariola Saternus

The quality of the liquid metal has the biggest influence on the quality of the final products. In the metallurgical industry, and especially in aluminium production the refining process is the important technological stage. Today the most popular are refining reactors with impellers like URO ? 200, which can generate small gas bubbles. A rotary impeller also makes the metal bath to be stirred well. There are two basic hydrodynamic parameters: the flow rate of refining gas and the mixing of refining gas (impeller rotation) that influence metal stirring and generating small gas bubbles. The paper presents the influence of the flow rate of refining gas on the hydrogen removal process from aluminium (final hydrogen concentration), taking into consideration the refining process of AlSi7Mg alloy and using URO - 200. The mathematical model of this process is also presented. The equation needed for calculation of the final hydrogen concentration as a function of the equivalent bubble diameter is shown. Basing on this equation the calculations of bubble diameter and optimal refining time are done. This paper presents the physical model (the water one) of aluminium refining process and the gas dispersion taking into account the fact that the gas flow rate is changing from 2,5 to 17,5 l/min and the impeller speed is changing from 0 to 400 rpm. Schemes of gas dispersion in liquid metal in comparison with the model data are shown and the optimal values of the gas flow rate and the impeller speed are chosen.

Jan 1, 2006

By Xi-Shan Li, Qian Li, Yong-bin Yang, Li-na Cui, Tao Jiang, Jie Ge

"With regard to control environment pollution in the roasting pretreatment of sulfur & arsenic-bearing gold concentrate, roasting of double-layered pellet was proposed. In the paper, the characteristics of double-layered pellet roasting were studied. Removal and solidification rates of sulfur and arsenic were investigated as primary factors. The result indicated that the removal and solidification rates of arsenic reached up to 95.91 % and 98.95% while the sulfur was 97.19% and 97.90% respectively on the premise of adopting slaked lime as solidified agent at temperature of 6000, the package proportion of 2.14 and roasting time of 3h. However, pyrite and arsenopyrite were transformed to hematite and magnetite and product of solidification mainly consisted of calcium sulfate, calcium arsenate and calcium sulfite within optimum roasting parameters.IntroductionUtilization of refractory gold resources has been gradually concentrated on with the depletion of the gold resources which are easy to deal with in the world [1]. Sulfur and arsenic-bearing gold ore is a typical refractory gold one, in which ultrafme gold is encapsulated in the structure of metal sulfide minerals [2,3], so it gives poor recovery through direct cyanide leaching. These refractory ores need pretreatment before the process of cyanide leaching to undermine lattice structure of pyrite and arsenopyrite containing gold [4] so that the gold could touch with cyanide solution [5]. Among various methods of pretreatment, conventional roasting method is most effective, but this process generates gases such as S02 and As203 harmful to environment. Therefore solidification roasting was proposed to solve this problem occurring in the conventional roasting at the end of last century."

Jan 1, 2013

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By M. Sripathy, K. V. Sharmal

"The conventional fiber reinforced plastic does not participate in the plastic deformation or enter the large plastic deformation state during collision. On the other hand, sandwich structure allows more plastic deformation, which improves the energy absorption efficiency. The objective of this study is focused on the investigation of the crushing of sandwich structure made from sisal / coir / bamboo/ glass fabrics as reinforcement and with polyester resin to form the composites skin and with polyurethane foam as the core. Experiments were conducted, showing that the underlying crushing mechanism of sandwich structures is very different from that of solid-section thin-walled structures. When a sandwich is subjected to crushing, the core deforms in the shear mode and the face bends independently. The damage is through the width zone of crushed foam core accompanied by a residual crushing in the foam. It is shown that such damage causes a significant reduction of compressive strength. Results show that glass/polyester and bamboo/polyester skin based sandwich structures have superior compressive strength. Coir /polyester based sandwich structure come next to glass/polyester sandwich structures in this aspect which is then followed by Sisal /polyester based sandwich structures.IntroductionCellular polymeric foam sandwich structures are often employed in shock mitigating applications. The cellular polymeric foam has several favorable properties, such as, low density, relatively high strength-to weight ratio and a significant degree of crushability. This high crushability is the result of the large void ratio in such materials, which also facilitates the collapse of cell walls via bending and buckling [1]. A few feasibility studies on FRP sandwich panels show that the panels efficiently provided high mechanical performance for minimum weight [2]."

Jan 1, 2012

By T. A. Edison

A distinct hydrocarbon maturation anomaly coincides with the Gold Acres open pit, Nevada (Figure 1). Both atomic hydrogen to carbon (H-C) ratios and reflectance measurements of contained organic matter indicate significantly higher maturity in samples collected within the confines of the open pit than in samples from the surrounding region (not shown in Figure 1).

Jan 1, 1987

By Xiangru Chen, Qijie Zhai, Haicheng Li, Chao Yang, Zhang Wei

The Nb-rich phase generated by the addition of trace amounts of Nb(<0.1wt%) \ and the effects of different content of Nb on the morphology and distribution of graphite in ductile iron were studied in this paper. The results showed that when the content of niobium less than 0.1wt%, the two-dimensional morphology of Nb-rich phase existed in microalloyed ductile iron were mainly regular pattern such as square, triangle, polygon etc. Besides, Nb-rich phase in large size distributed in the matrix with a certain distance from graphite. With the increasing amount of niobium, the dispersion degree of graphite diameter, average diameter and roundness increased slightly, and the number of graphite decreased slightly.

Jan 1, 2015

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By Donghai Li, Cheng Pan, Xuyang Liu, Xuewei Lv, Chenguang Bai

"Fine chromite ore is the common raw material to produce ferrochrome alloy through the submerged electric furnace process. The electric resistivity of fine chromite ore plays an important role in the operation efficiency because it determines the current distribution. The effect of particle size and the contact area of the particles on electric resistivity for several of chromite were investigated at room temperature, and the relationship between the electric resistivity of mixed particles and the volume fraction of lump ore to fine ore was also studied. The results shown that the electric resistivity increases with the increase of particle size, and the electric resistivity of mixture decreases with the increase of volume ratio of fine ore.IntroductionChromium is one of the most important alloying elements in manufacturing of stainless steel that used at high temperature and corrosive environment applications [I, 2]. As the raw materials to be charged into the steel, ferrochromium alloys and charge chromium are produced directly by smelting of chromite ore with the reducing agent in submerged electric arc furnace (SAF). During the process, the oxides of chromium and iron were reduced by carbon and meanwhile the electrical energy were consumed [3,4]. The ideal industrial process is to achieve high recovery level of Cr and Fe with minimal power consumption. In SAF process, the electric resistivity of charge stock has significant effect on the current distribution, which determines the heat distribution, molten bath structure and chemical reactions in the furnace. High resistance of the charge is desired to reduce the current distribution through the charge stock, thus the electrodes may insert into the charge stock with proper depth to form a high temperature arc heat source, and proper smelting can be realized[5]."

Jan 1, 2012

By Jing Zhan, Chuanfu Zhang, Yonglin Yao

"The Ni/Co arbitrary ratios of fibrous precursor were investigated during coordinated coprecipitation by changing the precipitating medium. The results show that the original molar ratio ofNi2+ to Co2+ in reaction solution can be maintained in the coprecipitate at pH'.'05.0 and the coprecipitate is single phase solid solution using water and water-X precipitating medium. But the original Ni/Co ratios are no longer kept and composition of the coprecipitate is not uniform at pH>5.0 in water precipitation medium. In order to obtain the precursors with the required morphology and accuracy Ni/Co ratios, the optimum conditions of fibrous precursors were chosen as follows: ammonia used as complex agent and pH adjustor, water-X solvent as precipiting medium, oxalate as coprecipitated agent, 8.0-8.4 for pH value, 50-70°C of reaction temperature, 0.5-0.8 mol/L of initial nickel and cobalt salt concentrations and excesses of oxalic acid of 10% - 20%.IntroductionNi-Co alloy as an important transition metal alloy with high mechanical strength, good anti-deformation, corrosion resistance, thermal conductivity, thermal stability, electrical conductivity, electrical contact, and special magnetic properties indicates that it can be used as high-temperature catalyst, special magnetic material, high-temperature electrochemical devices, and so on [1-6]. An ideal composite powder should have an appropriate stoichiometric ratio, good uniformity of chemical composition, appropriate phase, low impurity content and small particle size [7]. Similarly, the composition of nickel-cobalt alloy powder has an important impact on its crystal structure, properties and applications. Guo[8] found that magnetisms of CoxNi1-x such as magnetic anisotropy, curie temperature, and the shifts of the spin steering are very sensitive to the composition of alloy powder."

Jan 1, 2013

By Thomas Brynjulfsen, Merete Tangstad

"Manganese ore fines, generated during mining and transportation, can not be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore and subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace they are agglomerated into sinter, pellet or briquettes. The agglomeration process will however change the reduction properties of the ore. In this work the melting and reduction properties of sinter has been investigated.The melting temperature and melting mechanisms has been studied. The mineralogy of the raw ores and agglomerated has been found using XRD, and the composition established using EPMA(WDS). The effect of adding fluxes such as dolomite and quartz has also been investigated.IntroductionManganese metal is produced in a submerged electric arc furnace or in blast furnaces. The reduction of manganese oxide in blast furnace has in the recent years become more unusual due to the high consumption of reducing carbon material[5]. Manganese metal for alloying in steel usually contains silicon and iron, and are therefore called ferro manganese and silicomanganese.During mining, transportation and handling the manganese ore is broken up into different size fractions. The larger lump are used directly in the electric arc furnace, but the finer materials can not be added without treatment. The fine ore can disrupt the flow of CO and CO2 gas through the burden, subsequently reducing the degree of pre-reduction. The fine fractions must therefore be agglomerated into larger lumps, in order to promote gas flow. This can be achieved through a number of different processes. The agglomerate used in this work has been sintered, which means that is has been partly molten and reduced, in order to create bigger lumps."

Jan 1, 2012

By R. T. Jr. Faria, H. Vargas, R. Toledo, S. Cosin, V. P. Souza

"With the purpose of decrease environmental impact, caused by industrial residues (just discarded in the environment) and clay extraction in the ceramic industry, sanitary ware wastes were incorporated into clay. In contrast, it is important to evaluate not only the technological essays but also gases emissions in the ceramic firing process. The pollutant gases emitted in ceramic with residues can be in much larger concentrations than that in a pure clay ceramic firing or, on the other hand, can decrease the pollutant gas concentrations. With the aid of thermal analyses and photo acoustical techniques it was observed that sanitary ware waste can reduce the C02 emission. The gas emissions were shown as in function of firing temperature from 300 DC to 1100 DC. In order to analyze phase transformations during the firing process, clay samples and wastes were both analyzed by x-rays fluorescent chemical analysis and x-rays diffraction.IntroductionResearch works on the structural and physical changes that wastes, mainly industrially produced, cause to the final ceramic product has been rapidly expanding in these last two decades. See, for instance references in [1]. In spite of these examples of a continuous effort to incorporate wastes into clay ceramic motivated by technical and economical advantages, environmental issues are still a matter of concern. However, the gas emission due to the clay firing process and its related atmospheric pollution may be enhanced as a consequence of an incorporated waste [2]. It is known that the firing of clay ceramics in conventional furnaces using fuels such as wood, charcoal, heavy oil and natural gas generates appreciable amounts of gaseous components, mainly carbon dioxide (CO2), carbon monoxide (CO) and methane (CH4). Additionally to the atmospheric pollution, these gas sets could be harmful to the human health and can corrode equipments [3,4]."

Jan 1, 2012

By Roger Wilmoth

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the U.S. Environmental Protection Agency?s, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open-Pit Highwalls Demonstration Project. This project is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome U.S., located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 metres (m) and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied insitu treatment technologies included: 1) A modified, furfuryl alcohol resin sealant, utilizing wood and agricultural by-products to coat the rock surface. 2) EcobondTMARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface. 3) Two ARD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: 1) ASTM D 5744-96, Accelerated Weathering of Solid Materials using a Modified Humidity Cells, 2) mine wall residual wall rinse sampling, 3) microscopy, and 4) core drilling followed by water injection testing.

Jan 1, 2003

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

In this study, Raman spectroscopy was utilized to investigate the evolution of char structure in pulverized coal (PC) during microwave irradiation. The results indicated that though microwave treatment was carried out at low powers of 132W or 264W, significant variation in char structure was still observed. Char structure turned out to be more irregular firstly under microwave irradiation. However, char structure of superior regularity was obtained with the extension of irradiation time. It can be conclude that short time microwave treatment may facilitate the chemical activity of coal, while long time microwave irradiation on PC may deteriorate its combustion or pyrolysis property.

Jan 1, 2016

By Akram Alfantzai, Farzad Mohammadi, Maysam Mohammadi

"Degradation of lead anodes has always been a major concern among the electrowinning industries. In this study, the effect of agitation of the zinc electrowinning solution on the integrity of lead anodes was investigated. Galvanostatic experiments were performed at 37±0.5°C using 0,600 and l000rpm magnetic stirring rates for 24 hours. The Pb02 layer formed on the anode surface was reduced to PbS04 (discharged). The discharge information was used to calculate the amount of Pb02 present on the surface. Weight loss measurements along with the discharge calculations revealed that the degradation rate of the lead anode increased as the solution was stirred more vigorously. Furthermore, the amount of remaining Pb02 on the surfaces was decreased as a function of solution velocity. Therefore, it may be concluded that, degradation rate oflead anodes is controlled by detachment of the corrosion products from the surface rather than by electrochemical reactions. IntroductionElectrowinning is one of the extraction stages of zinc, in which pure zinc is deposited from acidic solution after froth flotation, roasting and leaching processes. The anode electrode materials play important roles in the electrowinning process. Their electrocatalytical capacities determine the oxygen evolution overpotential, and consequently the cell potential and energy efficiency of the zinc electrodeposition [l]. Purity of the zinc deposited on the cathode is affected by the solubility and corrosion resistance of the anode materials. Using insoluble materials as anode in the electrowinning leads to the higher purity of the deposited metal on the cathode[2]. Lead (Pb) and its alloys have been used as the anode in the zinc electrowinning because of its special properties such as relatively low cost, low melting point, insolubility in solutions containing sulphuric acid and high conductivity in both states of metallic and oxidized [3, 4]. In zinc electrowinnig, zinc reduction occurs on the cathode (reaction 1) and the oxygen evolution reaction (OER) (reaction 2) is the main anodic reaction [5, 6]."

Jan 1, 2013

By Veronica Escobar

This paper presents results from a two month pilot evaluation of EMEW® technology at CODELCO Radomiro Tomic, in Chile. A prime focus in the test programme was to assess the technology?s capabilities to recover high quality copper from the Radomiro Tomic electrowinning tank house bleed stream. The EMEW® cell developed by Electrometals Technologies Ltd. tolerates substantially higher levels of contaminants than those found in conventional tankhouse, operating at high current densities while maintaining high cathode copper quality all the way down to low copper concentrations. To maintain high copper purity in a copper electrowinning (or electro-refining) tank house, a continuous bleed of solution must be taken from the tank house inventory to prevent build-up of contaminants, and resulting degradation in cathode quality. In an SX-EW operation, this bleed stream is normally recycled back to the solvent extraction circuit, but is occasionally sent to the raffinate pond to re-enter the leach circuit. Return of the bleed stream to the solvent extraction circuit creates a continually recycling load of copper in solution, which may reduce overall plant capacity and expansion potential. Return to the leach circuit has a similar effect, and methods to reduce its impact are always under consideration. The use of the EMEW® technology allows for direct and efficient recovery of near 100% of the contained copper instead of recycling. Tests were run at ambient temperature on bleed electrolyte using current densities which varied between 250 and 1100 amps per square meter, with copper concentrations between 38 and 1 g/l. A profile of maximum allowable current density with respect to concentration was developed, showing that high grade copper can be obtained at all levels of concentrations tested, by choosing an appropriate current density and electrolyte flow rate. The results of this programme show that the recirculating bleed electrolyte from an SX-EW operation can be converted into an expansion in copper production at a comparatively low investment cost.

Jan 1, 2003