Search Documents

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By W. John Rankin

The finite and non-renewable nature of mineral resources poses unique challenges for sustainability: How can mineral and material needs of society be satisfied indefinitely? How can the benefits of exploitation of minerals best be captured for present and future generations? How can the environmental problems caused by large scale mining and processing best be ameliorated? These issues are rarely addressed, or if so only incidentally, in traditional courses in geology, mining, metallurgy and materials yet addressing them will increasingly be a major role for professionals in the minerals and materials industry and related sectors and agencies. This paper describes a framework for examining these and other sustainability issues related to meeting future material needs from non-renewable resources. The framework may be useful for educational purposes, either as the basis of a dedicated subject or by including the elements of it throughout a traditional course in relevant subjects.

Jan 1, 2014

By R. W. Lawrence

A method by which it is possible at an oxidation potential below 680 mV SHE to achieve quantitative conversion of sulphide sulphur to elemental sulphur instead of sulphate in a biological leach of chalcopyrite and bornite has been investigated. The process chemistry, biological phenomena and process flowsheet options are discussed. Several copper concentrates have been evaluated and have been found to be amenable to th process. Results to study the progression of chalcopyrite decomposition during the leach are presented and mineralogical factors affecting the requirement for silver addition are discussed. A chloride addition method for improving silver recovery is described. The results of a small scale continuous leach test have demonstrated that continuous operation can be carried out with high copper extraction and stoichiometric conversion of sulphide sulphur to elemental sulphur.

Jan 1, 1985

By Takahiro Furuzono

Saganoseki Smelter and Refinery of Pan Pacific Copper Co., Ltd. started treating copper anode slimes using a unique hydrometallurgical process in chloride media in 1997. The process comprises the following stages, decopperizing, wet chlorination, solvent extraction for gold, silver chloride reduction, and separate reduction stages that treat the gold extraction raffinate with sulfur dioxide gas. Precious metals and rare metals in the copper anode slimes are dissolved in an aqueous solution of hydrochloric acid by oxidative leaching, which is termed wet chlorination. Gold is efficiently extracted from the chlorination liquor by dibutyl carbitol in the solvent extraction stage. Gold is reduced by oxalic acid from goldloaded dibutyl carbitol and recovered as gold powder. The gold powder is cast directly into granules or ingots of more than 99.99% purity without electrorefining. Selenium is recovered as a selenium residue by reduction with sulfur dioxide gas and refined through vacuum distillation. The plant was designed to process 132 tonnes of copper anode slimes per month and has a current capacity of 206 tonnes per month due to several enhancements. Compared with the conventional process, the hydrometallurgical process described here provides some advantages, in particular, a higher product quality, shorter gold-retention time, and reduction in environmental load.

By Martin Fischer

A new method for the quantitative image analysis of complex microstructures in steel is presented. Microstructures in modern steel grades on the one hand become more and more complex while on the other hand the size of the constituents is scaled down ever further. For these reasons it is increasingly difficult or even impossible to access reliable quantitative information on ratios, shapes and spatial distributions of individual phases and constituents by utilising traditional metallographic analysis methods. The presented new analysis approach is object-based. Its basic processing units are so-called ?image objects? which reflect the pictured structures by merged groups of likely related pixels. By the use of image objects, information on shape, graphical texture and spatial distribution of the microstructural constituents can be processed. With these additional data available, it is possible to quantitatively analyse complex microstructures. This is demonstrated by the application of the method to SEM images of different multiphase steel grades. Because the analysis routine is fully automated, the analysis of large amounts of image data is possible and thereby the investigation of statistically relevant areas of microstructures.

Jan 1, 2009

By Michael P. Meisel

Solinox is a physical scrubbing process capable of removing a number of noxious materials from off-gasses, especially SO2, hydrocarbons, halo¬gens, heavy metals such as dust, etc. As these materials are dissolved physically, (not chemically bound), the solvent is absolutely stable and no by-products are formed in the scrubbing cycle. The process has been installed in three plants up to now, treating from approximately 30 MMSCFD to approximately 100 MMSCFD. These installations are in a non ferrous metal smelting operation, in a cellulose factory, and in a roasting process.

Jan 1, 1992

By Gerardo Muñoz

All along this century CODELCO's smelters have been operating on conventional technology, which Codelco has streamlined by using oxygen, developing oxy-fuel burners for reverberatory furnaces and introducing oxygen smelting of concentrates in converters (Teniente Converters). Chuquicamata began capturing sulfur from its first Teniente Converter in 1985. Since then, it has implemented a program allowing to gradually increase such capture. In 1994 a Frame Law on the Environment was enacted in Chile. By virtue thereof and of CODELCO's corporate environmental policy, an investment program aimed at capturing more than 95% of gaseous pollutants in all its smelters in a term not exceeding twelve years was established. The above entails a substantial improvement of the operational management as regards fugitive gases capture and treatment. This paper describes the way CODELCO is to deal with this challenge with a view to fully complying with environmental regulations and obtaining the required environmental certifications of its operations.

Jan 1, 1996

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non-ferrous metallurgical industry is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to ta,ke place at 'high temperatures and are now rapidly becoming accepted In many industries. This paper reviews experiences with a proprietary low density ceramic filter element. CerafH. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non- ferrous metallurgical industry Is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to take place at high temperatures and are now rapidly becoming accepted in many industries. This paper reviews experiences with a proprietary low density ceramic filter element, Cerafill. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008

By S. Motoiu

Data acquisition is widely used for controlling flash smelting furnaces. A Romanian smelter from which a large amount of data can be collected uses such a technique. A computer program was developed for interpretation of the data. Inputs to the program are the process data files. Abnormal data are identified using standard statistical techniques; they can be edited if necessary. The following methods can be used for the analysis: linear correlation (single or multiple), polynomial correlation or comparison of two average values. Time variation graphs and histograms can be displayed. The random balance method was used for determination of significant parameters influencing the process performance. Not all process parameters are recorded, and some of them are not even measured. The software can compute some of these parameters such as: air flow rate required and the oxygen content of the gas: exiting the reaction tower. The software was used for the interpretation of a large amount of process data. The analysis showed that the process did not operate properly at some times.

Jan 1, 1999

By A. V. Tarasov

The nonferrous metals industry has been a sector with one of the highest growth rates during the recent years. The prospects for the Russian metals industry during the period until 2010 are associated first of all with a growing domestic demand for its products. The technological level of the metallurgical operations in Russia is relatively low in comparison with industrially developed countries: the average energy requirement is higher by 20% to 30%; the amount of generated waste in the process of rolled products manufacture is twice as high; the average labor productivity is lower by 2.5 to 3.0 times; the overall negative environmental impact is twice as high. Improvement of the technological level of the nonferrous metals production under the conditions of market economy is possible by application of innovative technologies for the development of this sector. The main trends for development of the nonferrous metals sector are: - meeting of more stringent requirements to the quality of concentrates; - more complete recovery of associated elements as commercial-grade products; - development of continuous process lines based on autogenous, resource-saving and environmentally safe processes; - use of combined technologies, including pyrometallurgical, hydrometallurgical and upgrading processes; - expansion of the fields of application for nonferrous metals and their alloys.

Jan 1, 2006

By Khosrow Nikkhah

Increasingly ion exchange systems are being included in design of hydrometallurgical plants for metal extraction or impurity removal. Because such systems operate sequentially and are based on resins that exchange one ion for another, store it temporarily and release it to a regenerating solution, the usual steady state heat and mass balancing tools and spreadsheets cannot be used to design them successfully. This paper outlines the role of dynamic simulation in design of ion exchange systems. Examples are given for use of dynamic simulation in design and investigation of equipment based on consideration of the effect of input criteria such as expected ion loading and elution profiles. The methodology for dynamic modeling using IDEAS in design of multi column ion exchange trains operating in parallel is presented. Results shown include the non-steady state distribution of extracted metal and limitations imposed on operating conditions. These conditions include proposed sequencing of columns for loading and elution cycles, loading, elution and recycle flow rates as well as size and choice of related ion exchange plant equipment.

Jan 1, 2003

By Anthony C. Mulligan

Metals have historically been used in mining since they offer an excellent combination of hardness, toughness and cost and can be fabricated to form a variety of shapes. However, for many applications the metals used today have limited performance in the environments in which they are needed. This is particularly true for geothermal environments where the brines are highly siliceous causing corrosion and accelerated wear of many components. Geothermal sources are increasingly being explored for their high thermal value as well as possible sources for future minerals. While advanced ceramics have historically been expensive to produce in comparison with metals, they offer significantly greater corrosion resistance and hardness and can improve the overall performance when used in selected ?problem? areas. One of the major drawbacks in the use of ceramics in high impact areas has been their brittle nature and propensity to fracture and spall (fail) when loaded. Recent advances in the fabrication of ceramics have combined hard (strong) ceramics with more ductile ceramics in a architecturally designed microstructure, thus allowing ceramics to perform well in these high impact regions. Additionally, ceramics are significantly more inert to corrosion from either alkaline or acidic environments and can typically be used for significantly longer periods in these environments than their metallic counterparts.

Jan 1, 2006

By Markus A. Reuter, Antoinette van Schaik

"Product design engineers select from a wide range of materials and combine them into multimaterial product designs. These include various materials (metals and non-metals) which are complexly integrated (e.g. welded, glued, alloyed, layered). The recycling/recovery rate of consumer products are determined by the different materials and alloys used, but also by the particle size and multi-material particle composition after shredding (combination of materials due to design). Eco-design (for recycling) and Design for Recycling (DfR) can only be conducted if the interconnectivity of material/metal in various unliberated materials is accounted for and its effect on material and energy recovery can be linked back to design. This paper will discuss the basic principles of these DfR models and it is shown how these tools (i) are linked Computer Aided Design (CAD) and Life Cycle Assessment (LCA) software, (ii) affect conceptual design specifications of products, (iii) integrate the complex detail of the recycling system and recyclate quality and hence (iv) make recycling an integrated part of the product system. Furthermore, it is shown how these assessment tools and models can be applied for benchmarking of the recyclability and environmental damage created by the recycling of end-oflife consumer goods in order to e.g. (i) provide the (original) equipment manufacturer with knowledge and solutions to support product stewardship and Extended Producer Responsibility; (ii) create awareness of the consequences/benefits of design, products and recycling systems to manufacturer, designer, legislator, recycler etc.; and (iii) assist the consumer in their choice of consumer goods from an end-of-life point of view.IntroductionA first-principles basis is required in order to be able to simulate and predict the recycling/recovery behaviour of products facilitating Design for Recycling (DfR) and Eco- Design. This links recycling technology and the environmental consequences of recycling directly to product design."

Jan 1, 2008

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By Robert D. Boiler, Bill Wilkie

"There is a wide choice of different types of woven filter media for hundreds of different filtration applications. Factors such as type of fiber, synthetic polymers used, weave style, fabric finishes and fabrication techniques all play an important part in selecting the best choice for a specific type of filter and process application. The purpose of this paper is to offer some basic knowledge of these factors and how they can impact the performance of a filter, the life of the media and the overall cost of operation through case studies of actual plant filtration applications.IntroductionThe use of woven filter cloth in liquid/solid separation applications is generally well known. Woven filter cloth, by the nature of the weaving process, offers unique consistency and repeatability when compared to some other filter media such as needled felts, papers, sintered structures and knitted cloth. This unique consistency and repeatability is particularly applicable to woven filter cloth produced using monofilament fibers. These fibers are consistent in shape and form the basis for a woven cloth with predictable pore size and throughput characteristics. Woven filter cloth can be used in most wet filtration applications. Typical examples are the separation of chemical and pharmaceutical solids from process liquors, waste stream solids capture, liquid foods clarification, mining separations, and polymer filtration.EnvironmentOne of the first considerations is the environmental demand of the given process. Though it is tempting to look immediately at the particles in a filtration process, it is often better to consider some of the more basic needs of the system. There are numerous materials available, both synthetic and wire cloth. Each has its own unique set of properties."

Jan 1, 2012

By Ravinder N. Reddy

Electrochemical capacitors are charge storage devices. They bridge the gap between dielectric capacitors and batteries in terms of energy and power density. Electrochemical capacitors are classified into two types, electrochemical double layer capacitors (EDLCs) and capacitors based on pseudocapacitance. In EDLC, charge is stored at the interface between electrode and electrolyte. Carbon is considered to be prime electrode material for EDLCs due to its many favorable characteristics. In this study carbon materials are derived from thermal decomposition of catechol- formaldehyde polymers and are studied as electrode material for electrochemical double layer capacitors. Carbon electrode surface is characterized using NOVA 1200 gas sorption analyzer. It is also characterized using XRD and SEM. Carbon electrodewaselectrochemically characterized using cyclic voltammetry (CV). A highest capacitance of 110 F/g was observed in 30 wt% H2SO4.

Jan 1, 2006

By Freddy Syvertsen, Ali Riza Tarakcilar, Engin Tan, Derya Dispinar

"It has been shown that the disturbance of the advancing liquid front in the mould cavity may lead to surface entrained defects known as bifilms. These defects can deteriorate the mechanical properties significantly. The developments in the simulation of castings aid many casters. It is quick and economical. Therefore in this work, the aim was targeted to optimise the mould filling of a tensile test pattern design that is used for aluminium alloys. Several different designs, gatings and runner systems were investigated with Vulcan Casting Simulation Software. In addition to the achievement of non-turbulent and quiescent mould filling; other parameters such as temperature profile, porosity and feeding were investigated to optimise the process.IntroductionConsiderable effort has gone into understanding and controlling defects that are formed in aluminium and its alloys during casting. The conventional approach was the elimination of porosity by eliminating hydrogen in the melt simply due to the following reaction:"

Jan 1, 2012