Search Documents

By T. Shibaraki

A new larger, more efficient and economical Mitsubishi furnace line at Naoshima was put into operation in May 1991. Naoshima Smelter had produced previously about 230,000 mtpy anode copper with two smelter lines, i.e., a conventional reverberatory furnace line and Mitsubishi furnace line, which had been shutdown at the same time of the start up of the new smelter. At the beginning of the operation, there were several initial problems at the area of off gas trains and feeding system. By overcoming them now the process has been continuing satisfactory operation at the design rate. The paper describes about the design concepts and the actual operation of the new smelter.

Jan 1, 1993

By Qiang Zhong, Qian Li, Yongbin Yang, Tao Jiang

Thermogravimetric analysis (TGA) has been used to research the pyrolysis and combustion processes of coal used in rotary kiln of iron ore oxide pellet. Furthermore, the effects of air flow and oxygen concentration on the combustion behavior of coal were examined with TGA. The results showed that two individual stages can be distinguished for the pyrolysis of coal, the water evaporation stage and the de-volatilization stage. And the information on ignition and burnout characteristics can be obtained from the combustion process analyzed by TGA. Large air flow almost has no effect to the combustion process except that it enhances combustion intensity. However, the combustion process is further accelerated under oxygen-enriched conditions. With all experimental results, it could provide an attractive approach of analyzing coal for the rotary kiln process.

Jan 1, 2016

By Edgar Peek

"The two dominant metallurgical problems in treating most base metal sulphide concentrates in both the chloride and sulphate system are iron removal and sulphur elimination, respectively [1-3]. In this paper the opportunities, limitations and fundamentals of the chloride metallurgy system are described against this background. Only the treatment of oxide and sulphide ores is considered. Both hydrometallurgical and pyrometallurgical unit process operations are highlighted, since most successful base metal processes are based on a combination of the two. Hence, an overview of the technical and also some economical aspects of chloride metallurgy are presented.This overview summarizes the successful applications of chloride metallurgy, but it will not give exhaustive process and plant descriptions. It predominantly focuses on the essential technical features of the metallurgical unit process operations, while providing numerous references separately."

Jan 1, 2011

By Takeshi Nagano

"Prior to discussing future trends of non-ferrous metals smelting and refining, the past developments are looked back. Social and economic environments in Japan over the past two decades are reviewed. Technological developments to comply with these environments are explained, taking for examples the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper tankhouse. After considering the factors which will influence the improvements in non-ferrous processing, future trends are forecasted generally for copper, zinc, lead, aluminum and rare earth metals. Recent development works in Japan for the future are also introduced. In the discussed area, it appears that the emergence of new innovative processes would be difficult. The progress will be made rather toward the sophistication of the existing technologies, utilizing the advancement of the related technologies such as computers, electronics, etc. IntroductionThis paper discusses the future trends of non-ferrous metals smelting and refining on the occasion of the international symposium, ""The Metallurgical Processes for the Year 2000 and Beyond"".It is considered that the improvement of technology is greatly influenced by the social and economic environments which surround it. From this standpoint, review was made of Japanese case over the past two decades. Various new technologies were developed also in the non-ferrous metal world to comply with the requirements under the above environments. The examples are described in the cases of the Mitsubishi continuous smelting and converting process and Onahama's jumbo tank system for copper electro-refining.After foreseeing the major factors which will affect the technological developments in the future, the trends are forecasted for copper, zinc, lead, aluminum and rare earth metals generally. Some development works in Japan, which will give suggestions for future trends, are also introduced in some detail."

Jan 1, 1988

By J. M. Zhuang

Lignosulfonates, by-products of the sulfite pulping process, have been utilized in a process [1, 2] to treat acidic rock drainage (ARD). This process is referred to as the LignorTM process. In the present study, lignosulfonates were found to protect lime from developing an external surface coating, and hence to favor its dissociation. Further, the addition of lignosulfonates to ARD solutions increased the clotting and settling rate of the formed sludge. The capability of lignosulfonates to form stable metal-lignin complexes makes them very useful in retaining metal ions and thus improving the long term stability of the sludge against leaching. The LignorTM process involves metal chelation with lignosulfonates, ARD neutralization by lime to about pH 7, pH adjustment with caustic soda to 9.4 ? 9.6, air oxidation to lower the pH to a desired level, and addition of a minimum amount of FeCl3 for further removal of dissolved metals. The LignorTM process removes all concerned metals (especially Al and Mn) from the ARD of the Britannia Mine (located at Britannia Beach, British Columbia, Canada) to a level lower than the limits of the BC Regulations. Compared with the high density sludge (HDS) process, the LignorTM process has many advantages, such as considerable savings in lime consumption, greatly reduced sludge volume, and improved sludge stability.

Jan 1, 2003

By L. J. Davies

Refractories usage in furnaces for the extraction of nickel from both sulphides and lateritic ores is reviewed. Recent changes in raw materials and basic brick qualities developed to meet the increasing demands of existing and new processes are outlined. Examples of used brick examinations to establish mechanisms of wear are given. The importance of physical and chemical properties are discussed. The use of simulative laboratory testing to aid in refractories development and selection is described.

Jan 1, 1988

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of873 OK is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composItion formed under roasting of concentrates with particle sizes less than 0.02 J..lm (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CufeSz) each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forehamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By Yuanbo Zhang, Ruijun Wang, Qian Li, Zhao Jing, Guanghui Li, Zhengwei Yu, Chen Liu

The high content of sodium and potassium in sinter is harmful for blast furnace ironmaking. Reductive sintering technology can remove more alkali metals than conventional sintering process. In order to improve the removal ratios of Na and K, reductive sintering with both CO-containing flue gas circulation and carbon-bearing pellet was conducted in this study. Experimental results show that all indexes except the VSV and P were improved in reductive sintering with CO circulation. Flue gas circulation technique combined with carbon-bearing pellets were beneficial to reductive sintering, because it could maintain good sintering indexes and enhance the removal of Na, K. The best removal ratios of Na, K and reduction degree of iron oxides were 20.37%, 63.73% and 23.76%. In reductive finished sinter, silicate mineral becomes the important binder phase, and main iron mineral phases are wustite (FexO) and magnetite (Fe3O4).

Jan 1, 2016

By Takeshi Nagano

Copper pyrometallurgy in Japan has experienced quite fundamental changes in last fifteen years. The severe environmental restriction coupled with increase of energy costs accelerated the development work of the new continuous process in Mitsubishi Metal Corporation. After several years of pilot plant test work the commercial plant was put into operation at Naoshima Smelter in 1974, the design capacity of which was 4,000 tonnes of copper per month. Many modifications and improvements have been incorporated into the process and 7,200 tonnes per month of copper production was achieved in 1983, proving that continuous process was much more economical than conventional process. It is now possible to design and operate the continuous process in wide range of capacity. This paper will review the process and describe the progress of the process in these 10 years. 311

Jan 1, 1985

By Edgar Blanco

A thermodynamic and experimental investigation to develop a new process for converting molybdenite concentrate to molybdenum dioxide by a water-vapor oxidation process was carried out. In addition, the behavior of rhenium and selenium in molybdenum concentrate during the process was investigated. The kinetics of the reaction were determined by measuring the weight change of a sample with time in water vapor at temperatures between 700-1000°C. The results were analyzed by a Shrinking Unreacted Core model under chemical reaction control, which showed an activation energy value of 102 kJ/mol. To determine the behavior of rhenium and selenium, their concentrations in the molybdenum sulfide and the product molybdenum dioxide were measured by the use of ICP. While most rhenium remained with the molybdenum dioxide after the water vapor oxidation, almost all selenium volatilized. These results agree with thermodynamic analysis.

Jan 1, 2006

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By P. N. Anyalebechi

"The as-cast microstructure of two commercial-size ingots of aluminum alloy 3004 produced by the electromagnetic casting process was quantitatively characterized. This involved the quantitative determination of through-thickness and across-width variations in dendrite cell size, grain size, macrosegregation of alloying elements, interparticle spacing, and the types, volume fractions, and sizes of the constituent or second phase particles. More than ninety-five percent of the constituent phases in the ingots consisted of the A16(Mn,Fe) phase; the desirable a-Al 12(Fe,Mn)3Si phase was not detected in any of the ingots by Guinier X-ray diffraction analyses or electron probe X-ray microanalyses. A significant microstructural heterogeneity through the thickness and across the width of both ingots was observed. For example, macrosegregation, and the sizes of the constituent phase particles, dendrite cells, and grains increased concomitantly from edge to mid-width and from surface to center of the ingots. There was a -20% depletion (negative macrosegregation) of Mg and a +54-87% enrichment (positive macrosegregation) of Ti in the center of the ingots. With the exception of grain size, there was no significant microstructural difference between the two ingots examined. The causes and practical implications of the observed microstructural heterogeneity in the ingots are discussed.IntroductionThe first step in the fabrication of majority of wrought products of aluminum and its alloys is the casting of large ingots or billets of simple shapes (round or rectangular). The sizes of the ingots vary from 10 mm to 450 mm diameter or 25 mm to 780 mm thick. The quality of the finished products is established at the ingot casting stage. This is because the microstructural characteristics, such as secondary dendrite cell size or arm spacing, amount of alloying elements retained in solid solution, macrosegregation, and the characteristics of second phases, produced during casting cannot be reversed by subsequent processing. Up until twenty-five years ago, the effect of as-cast microstructure of large ingots on the structure and behavior of thin sheets (0.34 mm thick) during drawing and ironing processes was incorrectly assumed to be minimal or nonexistent. This was based on the erroneous notion that the thermal treatments and large reduction (>99.94%) and strain that the ingot undergoes during production of the sheets completely destroys the original ingot structure and its inherent heterogeneity. However, the effects of ingot structure can, a priori, be deduced from the observed effects of constituent phase particle size, type and volume fraction on recrystallization, development of texture during annealing and deformation, and earing. In fact, careful examination of the behavior of products produced from different size ingots or castings have shown that the original microstructure of the ingot has a direct impact on the properties and performance of the end products."

Jan 1, 2011

By Baozhong Zhao

The direct smelting of copper concentrates to copper metal in a single furnace offers environmental and energy advantages over conventional two-stage copper smelting processes. However, the direct copper making results in unacceptably high level impurities (As, Sb and Bi) in the anode copper. Experimental studies have shown that it is possible to remove these impurities from molten copper by injection of sulfur-hexafluoride. This paper discusses the experimental findings on the influence of various factors on the rate of removal of impurities, such as the impurity inter-effects, initial oxygen content in the metal and injection rate of SF6.

Jan 1, 1995

By Yin Zhang, Xiaoyu Huang, Mi Wang, Bencheng Du, Youduo He

"Burners are important facilities for blast furnace stoves to raise hot-blast temperature up to 1200°C. Common types of two-ring ceramic burners have very long flames so that part of combustion occurs in the upper part of the chequers and will cause damage to the refractory materials. Using computer simulation to analyze the turbulent diffusion flame in the combustion chamber, some good results were obtained. A new type of ceramic burner will be installed by Anshan Steel Complex in stoves of blast furnace number 4. A pilot experiment was done on the new burner. The experimental data have shown that the mixing condition was improved and the length of flame was shorter with the new type of ceramic burner.IntroductionPulverized-coal injection can give significant operating saving, reducing coke rate in blast furnace(BF) operation. However, during high rates of coal injection, extra heat must be compensated in hearth to maintain certain raceway adiabatic flame temperature. One of the effective methods for heat compensation is to raise hot-blast (HB) temperature up to 1200°C. Nowadays, since the fuel being combusted in stoves is BF gas only, in which the calorific value is down to round 3000 kJ/m3 , to increase the combustion ability and to provide a suitable length of flame in combustion chambers of stoves becomes more important. In other words, designing a good ceramic burner which will affect to HB temperature and stove lifetime is drawing more attention."

Jan 1, 1999

By John Petersen

Heap bioleaching technology has become well established for the exploitation of copper sulfide ores. Still, in many operations the rate of copper extraction is rather slow, often taking two years or more to recover 80% of the copper. Chalcocite, the most common secondary copper sulfide, leaches by a two-stage mechanism. The first stage is rapid, whereas the second stage has a high activation energy and proceeds slowly at ambient temperatures. Nonetheless, this rate is still considerably faster than what is typically realized in a full-scale heap. A comprehensive column bioleaching study of a chalcocite ore has shown that the chalcocite columns are leached in a zone-wise fashion. The first zone corresponds to the first stage of chalcocite leaching, where all ferric produced by the bacteria is immediately consumed and all acid entering with the feed solution is consumed within a relatively narrow band. The second stage of chalcocite leaching proceeds much more slowly in the wake of the first stage, within a zone that grows gradually over the entire length of the column. The overall rate of leaching is thus determined by the rate of acid supply into the column rather than by mineral or bacterial kinetics, at least until the entire column is engaged in second-stage chalcocite leaching. In full scale heaps, there is evidence to suggest that solution distribution favours channelling between relatively large clusters of material which are exposed only to stagnant solution. Reagents have to migrate into such clusters by diffusion, which retards the delivery of acid dramatically. Thus, we believe that the rate of chalcocite oxidation in heaps is governed by sideways diffusion rather than downward migration. Column experimental results have been reproduced with a comprehensive heap-modelling tool. The model predicts that by simply changing the length of the average diffusion channel from column conditions (a few cm) to heap conditions (tens of cm), extraction times can change from weeks to years under otherwise identical conditions.

Jan 1, 2003

By Vianey Garcia-Osorio

One of the problems in the carbothermic aluminum process is the substantial loss of aluminum compounds as vapors due to the high temperatures in the process. In order to solve this problem a Vapor Recovery Unit (VRU) is proposed. In this unit operation the aluminum vapor undergoes a series of heterogeneous non-catalytic reactions forming solid, liquid and gas products. In this work a model for the simulation of this unit was developed which includes heat and material balances as well as heterogeneous non-catalytic reactions. The model leads to a system of differential equations; its solution was implemented in Matlab giving as a result a stage-by- stage solid-fluid reaction model.

Jan 1, 2001

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By Joseph Goodwill

1. PURPOSE The objective of this paper is to summarize a study undertaken by the EPRI Center for Metals Production (CMP). The overall purpose of the study was to identify electrolytic opportunities that might merit consideration for joint development by industry and EPRI. 2. SCOPE The electrolytic technologies of interest to this study include: Electrorefining, Electrowinning, and Fused-salt electrolysis. Recovery from primary, secondary, and waste materials were included in this effort; however, we excluded from consideration: Plating and coating operations, such as electrogalvanizing; Mining and milling operations in which electric energy is predominantly used for comminution; Electrothermal processes in which submerged-arc, open electric-arc, and plasma-based smelting processes use electric energy largely to provide a melting or refining ("heating") capability; and Aluminum electrotechnologies since these were the subject of a separate study (CMP 86-2). We recognize that there may be some "gray areas" between these excluded areas and the electrolytic sectors of interest. For this reason, a secondary criterium was used, namely, if the major use of electric energy was to extract or refine the

Jan 1, 1990

By William Petruk

The capabilities of SEM/image analyzers for determining quantitative mineral data which have a bearing on extractive metallurgy have given applied mineralogy a new dimension. The capabilities include automatic mineral identification, unattended operation, search for rare minerals, and measurements of (1) mineral quantities, (2) grain and particle size distributions, (3) liberation characteristics of minerals in ground ores, and (4) mineral associations. Data on mineral quantities define the distributions of elements among minerals, provide background information on characteristics of the samples, and provide a data base for a mineral-materials balance. Size analysis data of the minerals in unbroken ores are used to predict the grind required to liberate minerals. Data on liberation analysis can be used in many ways. One application is to process the image analysis data for feed, concentrate and tails by a materials balancing technique to calculate the recovery of liberated and unliberated grains at each point in a circuit. The calculated recovery data define the behaviour of an ore in a concentrator, pilot plant or bench test, and indicate whether recovery improvements are possible and/or feasible for a particular ore.

Jan 1, 1991