Search Documents

By Takeshi Ohgai, Hisaaki Fukushima, Tetsuya Akiyama, Joon-Seo Ki

"Recently, an intensive attention has been paid to the electrodeposition of Zn-Cr alloy in the field of the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation. In this study the electrodeposition of Zn-Cr alloys from the sulfate baths was conducted to investigate the codeposition mechanism of Cr with Zn. As a result, Cr was codeposited with Zn at higher current densities in both polyethyleneglycol(PEG)-free and PEG- containing baths. However, PEG made it possible to reduce Cr+ to the metallic state and Cr existed in the form of Cr(III) hydroxide in the deposits obtained from PEG-free bath. The measurements of the partial polarization curve of Zn and the pH in the cathode layer revealed that PEG acted as a polarizer to shift the cathode potential to the reduction potential of the composited hydroxides of Zn and Cr formed due to the pH rise in the cathode layer.1. IntroductionRecently, much attention has been paid to the electrodeposition of Zn-Cr alloys because of its application to the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation1Hl_ Some researches have already tried to commercialize this type of steel sheet. High corrosion-resistance of this steel sheet is brought about by codeposited Cr in the alloys. According to Piontelli's classification5l concerned with metal deposition from aqueous solution, Cr belong; to an inert metal and its deposition is associated with a large amount of hydrogen evolution. Therefore the current efficiency for Cr deposition is extremely poor. It has been also reported that Cr is unable to codeposit in the electrodeposited Zn film in the absence of a certain additive in the solution. 0-compounds group colloids7l, ether group organic compounds8), 9>, peptide based compounds10l, etc., have been found to be effective additives to induce the codeposition of Cr with Zn. However, few studies have been made on the codeposition mechanism of Cr with Zn. In this research, the fundamental electrodeposition behavior of Zn-Cr alloys from sulfate baths was investigated to clarify the codeposition mechanism."

Jan 1, 1998

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By J. Rastas

The recovery of lead, silver and gold from existing and potential zinc process residues using a sulfidization-flotation method was investigated on a laboratory scale. The following residues were tested: neutral leach residue, high acid leach residue, and hematite residues. The sulfidization of lead and silver is carried out at low pH by the addition of a stoichiometric amount of sulfide at a controlled rate. To increase the particle size of the sulfides, seeding with synthetic lead and silver sulfides -is employed. The flotation is carried out at pH 2-4 using low pH-collectors such as dithiophosphates and dithiophosphinates. Special attention must be paid to the role of oxygen in the conditioning stage. The effect of different parameters on both the sulfidization and the flotation has been evaluated. Recoveries of 85-90, 90-95 and about 80 % were obtained for lead, silver and gold, respectively. Typically, concentrates containing 50-60 % lead, 3-5 kg/t silver and 10-15 git gold were produced.

Jan 1, 1990

By John J. Mortvedt

Application of some by-products of the metals industry which contain plant nutrients to agricultural lands could constitute resource recovery instead of costly disposal. Some industrial by-products contain appreciable concentrations of heavy metal contaminants, such as Cd, Cr, Ni, and Pb. After land application, these metals may be absorbed by plants and enter the human food chain or be leached to groundwaters. Plant uptake of these heavy metals varies with plant species:, soil pH, soil texture, and the particular metal. Certain leafy vegetables can absorb significant amounts of heavy metals, while absorbed metals are usually poorly translocated to cereal grains. Allowable heavy metal concentrations in fertilizers now are not regulated, but EPA is considering such regulations. Heavy metal impurities in animal feed supplements are regulated by the states; so some by-products may not be permitted for this use.

Jan 1, 1992

By Jorge Alberto Soares Tenório, Victor Bridi Telles, Denise Crocce Romano Espinosa, Felipe Fardin Grillo, Vicente de Paulo Ferreira Marques Sobrinho, José Roberto de Oliveira

"This research aims to study the process of incorporation of the metal iron in electric arc furnace dust (EAFD), from a steel mill producing long steel by liquid iron in addition to the changing temperature of 1400 degree Celsius altering experimental conditions such as how to add the EAFD (as received and in the form of briquettes), the percentage of EAFD to be added (10, 20 and 30% of initial weight of sample pig iron) and the time of withdrawal of the sample of pig iron and slag (30 minutes after the addition of EAFD). Previously, the EAFD will be characterized using the following techniques: chemical analysis, particle size analysis, X-ray diffraction, scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) microanalysis. After characterization, the eletric arc furnace dust to be added to the bath of liquid iron, will be divided into 2 types: the first order of addition will be in the form ""as received"" from the plant and the second is through the agglomeration of EAFD in the form of briquettes. The achievement of fusion experiments in laboratory scale, will take place in a vertical tubular furnace with temperature control. The fusion experiments to assess the incorporation of the metal iron will use graphite crucibles. A flow of inert gas (argon) will be maintained inside the furnace during the experiments. It is expected that the results obtained at the end of the research allow the evaluation of the iron metal incorporation of eletric arc furnace dust in hot metal bath.IntroductionThe steel industry generates a variety of solid wastes, liquid effluents and gaseous emissions at various stages of processing. The electric furnace dust (EAFD), generated in electric arc furnaces, represents a major problem for their content of chemical elements such as zinc, iron, chromium, cadmium, among others, issued to the atmosphere during the manufacture of steel[1]."

Jan 1, 2012

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By T. M. Dreher

The difficulties associated with the operation of a classical rhodium refining process have prompted many attempts to develop a viable solvent extraction flowsheet for rhodium. Recent investigations at McGill University have involved the activation of rhodium prior to its solvent extraction. The role of activation is to convert the aquochloro complexes of rhodium to a form extractable by conventional solvent extraction reagents. In the novel separation scheme identified, chloro complexes of rhodium are converted to bromo complexes, which undergo aquation to a lesser extent, making them more easily extracted. Rhodium is then extracted using Kelex 100, and stripping is achieved by use of a concentrated chloride based solution. Separation of rhodium from iridium is achieved by either prior reduction of Ir(IV) to Ir(III), as the latter is not extracted, or via co-extraction and differential stripping. A conceptual flowsheet for the refining of rhodium using this method is proposed.

Jan 1, 1998

By Metehan Erdogan, Orhan Gökçe Göksu, Ishak Karakaya

"An experiment (mixture) design was created to optimize the process parameters of the electrochemical reduction of CaW04 to W in molten CaCl2-NaCl eutectic mixture. Temperature, applied voltage and the length of Kanthal wire winding of the CaW04 pellets were selected as the process parameters that were allowed to vary between the predetermined minimum and maximum values. The rates of the electrochemical reductions were interpreted from the variations of current and total charge vs. time graphs under different conditions. The analysis pointed out that 640°C and 2.81 V resulted in the fastest reduction. Itwas seen that the effect of Kanthal wire winding on the output current was less pronounced when compared to the other two parameters.IntroductionFFC Cambridge Process [1] has been applied to a number of metal oxides in laboratory experiments to produce metals. In nearly all of these studies, the electrolysis temperature was around 900°C, the electrolyte was pure CaCl2 or CaCl2 containing salt solutions and the anode was graphite. However, it was recently shown that the electrochemical reduction process of metal oxides in CaCl2 containing electrolytes at the mentioned high temperatures was not suitable for tungsten production [2], It was reported that as soon as WO3 contacts CaCl2, the following reaction occurs:"

Jan 1, 2012

By G. C. Amstutz

The topic of the industrial applications of mineralogy is a vast field which can be adequately covered only in a large book or by a two or three semester course. This paper recalls experiences of the writer in this field, a task requested by the Process Mineralogy Committee. Therefore, this paper is largely an account of the industrial mineralogy problems I was involved with, since my student years, Although I will treat each application only briefly, it is hoped that they will illustrate to the students in the field how varied are the applications of mineralogical methods. In this respect, I want to emphasize that it is important for mineralogy teachers to point out the usefulness of mineralogical methods much more often in their courses. Not only does that help prepare young individuals for industrial careers, but also it arouses their feeling of consciousness of public responsibility which is an important attribute for the world's scientists. When professors utilize the varied applications in their teaching of mineralogical methods students then understand better the significance of learning those methods and appreciate the many years of necessary university preparation. The first time I was involved in an application of mineralogical methods was about 1944 as a student of Professor Paul Niggli. He was asked to study the problems of ice crystallization on wings of airplanes. The ice formed at high altitudes and during the winter. This was not outside his realm of expertise because he was the main initiator of the Snow Research Institute on the Weissfluhjoch in Switzerland. I believe that the work of this Institute was an important factor in stimulating much of the snow research subsequently carried out at the United States Army Snow Research Center, which was located at that time in Willmette near Chicago. Dr. Bader, one of Paul Niggli's former students, was the Director of Research at Wilmette at that time and for quite a number of years thereafter. A mineralogist-crystallographer can make important contributions to a better understanding of the problems of snow and ice formation, avalanche hazards, and the prevention of hail. The habits of snow crystals are essentially a function of the temperature and the humidity,

Jan 1, 1982

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don't allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir's law is discussed for different operating conditions.

Jan 1, 1996

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

By A. Mikula, S. Karlhuber

"Unique physical and mechanical properties made the Pb-Sn solders attractive for low temperature joining of electronic parts. But since lead in solder materials has become a great enviromental problem and health concern, lead will be slowly replaced by other materials in soft solders. Some of these materials which are currently under investigation are ternary tin alloys. Many different physical properties like wetting behavior, electrical and thermal conductivity and surface tension are measured on these alloys, but on the thennodynamic properties and the phase diagram of the alloys under discussion there is only little information available. We investigated the (Ag, Au, Cu)-Sn-Zn systems and determined the thermodynamic properties over the whole composition range by emf-measurements. From these measurements we also got some information on the liquidus. In the Sn-rich corner the phase diagrams are still under investigation.IntroductionSoldering is technically defined as the joining of two base materials, mostly metals or metal coated nonmetallic substrates, with a third metal. The melting temperature of the third metal or metal alloy should be well below those of the substrates. Solder alloys can be categorized in soft and hard solders. Soft solder alloys usually contain lead, tin, bismuth, indium or cadmium and hard solders gold, zinc, aluminium or silicon. The difference between soft and hard solders is the melting temperature of the soldering material. This temperature is around 350°C.An interesting brief history of solders is given by Vianco and Frear [1]. They report, that in 4000 B.C. solders were already used in Mesopotamia. From archaeoligical evidence those solders were gold-based hard solders.Tin-lead soft solders and their use are not easily found, because in course of time tin has been reduced to stannic acid, making the identification quite difficult. Well preserved soft solder artifacts were discovered in King Tut's tomb dating from 1350 B.C. In ancient time Pb-Sn solders were used primarily for the manufacture and repair of cooking utensils and metal tools. The Romans used lead-tin solders extensively in the construction of the aqueducts."

Jan 1, 1996

By Florian Kongoli

The behavior of cobalt as a by-product in the NilCu smelting and converting processes effects directly the quality of the final products as well as the revenues gained from the overall process. An effective way to evaluate and predict this important behavior is thermodynamic modeling which reduces the time and the cost of experimental investigation. In this work a thermodynamic model of cobalt-containing matte phase in NilCu smelting and converting processes is presented. The model predicts a priori the thermodynamic properties and phase relations of the ternary and multicomponent matte based solely upon the optimized parameters of the binary systems. This model can be used with other models such as those of slag, metal, gas etc. to predict various aspects of cobalt behavior such as matte- slag, metal-slag distribution, etc.

Jan 1, 1999

By Guo Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By D. M. Fermino, C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. Volzone

The present paper presents the study of light green smectite clay, from Paraiba, Brazil, submitted to mild acid attack under moderated conditions. Usually, clays are subjected to treatment with strong inorganic acids at temperatures near the boiling point and at high acid concentrations and then, widely used as bleaching agents. The treatment occurred under bellow boiling temperature and at short times of reaction (90°C, reaction times of 1, 6, 12, 18 and 24 hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, clay/acid solution ratio of 1g/10mL). The purpose of these attacks is to reduce the concentration of impurities providing color, with minimal change in the clay minerals structure, aiming at use in products of high value such as cosmetics and polymer/clay nanocomposites. The raw clay and the attacked samples were characterized by X-ray diffraction (XRD), cation exchange capacity (CEC), stereomicroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray detector (EDS).

Jan 1, 2015

By Natasa Mitevska

In order to ensure the minimal copper concentration in the reverb furnace slag, the graphical optimization method is used and the optimal slag composition of the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Serbia) is obtained: (Si02) .. 38.0%; (FeO) .. 40.0%; (Fe3O4) = 5.0%; (CaO) = 5.0%; (Al2O3) .. 6.0%. Keywords: Optimization, Reverb Furnace Slag, Graphical Method

Jan 1, 2003

By I. Gaballah

The chalcopyrite ore&apos;s anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994