Search Documents

By David C. Johnson

Coal mining in Illinois has resulted in many structures being exposed to subsidence damage. Damage mitigation techniques (DMT) applied in the foundation design/construction have proven successful in minimizing damage in several test cases. To determine the practicality of these techniques, the Costs of their application are investigated. The AMT costs are compared to foundation and total house costs for various classes and sizes of houses. An economical and effective subsidence resistant foundation construction is proposed.

Jan 1, 1993

By Axel Preusse

A high advance rate of the longwall face increases inevitably the mining dynamics within the rock and on the surface. Measures to limit the mining dynamics are the adjustment of the face advance rate to stretch the influences of mining over time and continuous winning to maintain a uniform influence of mining. This paper deals with the dynamics of mining subsidence within the range of a transmission overhead line for transportation of gasoline, diesel, kerosene, heating oil, mineral oil and other hydrocarbons. In a certain segment of the 24"-pipeline it was possible to predict, due to technical, operational and laying conditions, that undermining the pipeline would cause local stress maxima within the pipeline string. To limit these expected local stress maxima, the face advance rate of panel 497 was adjusted to the sensitivity of the pipeline towards the influences of mining. Comparison of the predicted mining dynamics, using the theory of stochastic media, with the measured ground movements led to the conclusion that the effects of dynamical influences which occurred within the range of the transmission overhead line and acted on it were low. This confirmed that the decision to adjust the face advance rate to the sensitivity of the transmission overhead line was correct (Kateloe et a)., 2002). A later relaxation cut in range of the pipeline siphon scarcely produced relaxation movements of the pipeline. The appointed sensitivity data of the undermined pipeline and the according maximum admissible face advance rate were thus correctly measured.

Jan 1, 2003

By Hani S. Mitri

The behaviour of grouted cable bolts used for rock reinforcement as a means of ground control in hard rock mining is investigated. The study utilizes an analytical model which is based on the variational principle to calculate the shear bond stress distribution along the embedded length of cable bolt. In this paper, a comprehensive parametric study which covers both geometric and mechanical design parameters involved is presented. Special emphasis is placed on studying the characteristics of the grout model represented by Winkler springs. This involved varying the maximum shear strength of the grout, its residual strength and the slip occurring between the cable and the borehole wall.

Jan 1, 1990

By T. N. Singh

Board and pillar system of mining has beer, practised in India in view of abundant availability of cheap labour force, low investment and quick return. Subsequently, selective mining from thick seems and partial mining under surface features boosted the trend. As s result over 2000 million tonnes of coal is locked up in form of developed pillars inclusive of about 1000 million tonnes of high grade coking coal in Jharia field alone. The trend of pillar formation is still uninterrupted as the estimated pillar reserve in this field in 1974 was only 700 million tonnes which increased to 961 million tonnes in 1983. The trend is not much different in other coalfields end as a rough estimate 100 million tonnes of virgin coal reserve is being transferred to pillar every year. The method of board and pillar mining is likely to remain moat preferred technology for decade9 to come in view of several inherent advantage in Indian mining conditions.

Jan 1, 1984

By R. Kaund

"Quantifying the rockburst consequence is of critical importance to reduce the hazards with preventative measures in underground mines and deep tunnels. Contours of energy components within a pillar model are plotted at different rockmass damage stages, and plastic strain work and released energy are proposed as indicators of rockmass damage consequence. One pillar model under different loading stiffness is simulated to assess indicators of pillar burst and the resulting damages. The results show the rockmass damage under soft loading stiffness has larger magnitude of plastic strain work and released energy than that which is under stiff loading stiffness, indicating the rockburst consequence can be quantified with plastic strain work and released energy in numerical models. With the quantified rockburst consequence, preventative measures can be taken to avoid severe hazards to mine safety.INTRODUCTIONWith the increasing demand of mineral resources and depletion of near-surface ores, the depths of underground mines have made the mining activities one of mankind’s most dangerous types of work (Ortlepp, 2005). The Mine Safety and Health Administration (MSHA) defines rockburst as “a sudden and violent failure of overstressed rock resulting in the instantaneous release of large amounts of accumulated energy.”The types of rockburst can be classified into three types: (1) strain burst, (2) pillar burst, and (3) fault slip (Müller, 1991). Strain burst is the most common type of unstable rock failure in underground openings, where the intensity and scale are usually smaller than pillar burst and fault slip (White and Whyatt, 1999; White, Williams and Whyatt, 2002; Ortlepp, 2005). The cause of strain burst can range from shattering of rock under high stress concentration to buckling of discontinuities parallel to underground openings. The occurrence of pillar burst also depends on the stress and discontinuity conditions in the rockmass, but pillar burst usually involves the sudden loss of strength in the core or foundation of a pillar (Whyatt and Blake, 2002; Kias and Ozbay, 2013; Khademian et al., 2016). Fault slip or slip burst can be either slip along pre-existing discontinuities or shear failure in the rockmass, when the shear stress is larger than shear strength in the fault (Rice, 1983; White and Whyatt, 1999; Sainoki and Mitri, 2014). The consequence of fault slip can vary from very small rockmass damage to consequential rockmass damage, but large seismic magnitude does not always result in large rockmass damage (White and Whyatt, 1999; Whyatt and Blake, 2002)."

Jan 1, 2018

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By Khaled Morsy

This study presents a typical stress-strain model for coal material using the available in-situ and laboratory tests data conducted on coal. This model can be used as a basic coal model in finite element applications The effects of pillar width-to-height ratio and the confining pressure have been considered in this model. The extended Drucker-Prager model with mobilized friction angle was found to be very successful in simulating the proposed model.

Jan 1, 2001

By Syd S. Peng

Full-face shield leg pressures in a longwall panel for a three-month period were collected and analyzed. The pressure data were presented in the following forms: full- panel full-face shield pressure, individual shield pressure, full-face shield pressure, full-panel time-weighted-average pressure, and relationships among setting pressure, final pressure and pressure increment. Although shield pressure varies from shield to shield and from cycle to cycle, the setting pressure and face advance rate do control the 6nal pressure and time-weighted average pressure.

Jan 1, 1997

By David Newman

The Southern Appalachian coalfield has a long history of coal bumps that are attributable to a unique combination of topography, geology, and multiple seam mining. The high pillar stresses that generate a coal bump result from: i. mountainous topography where the overburden commonly exceeds 1,500 feet beneath ridges, ii. multiple seam mining, iii. thin interburden between active and abandoned mines, iv. thick beds of competent sandstone and sandy shale strata throughout the stratigraphic section, v. strong coal seams, and vi. irregular pillar and mining geometry in older room-and¬pillar mines. Coal has been intensively mined for more than 100 years in Eastern Kentucky, Southwestern Virginia, and Southern West Virginia. As a result, it is commonplace to have abandoned mines above and/or below active operations. Therefore, those conditions that generate coal bumps will be more prevalent in the future, as underground mining continues in Southern Appalachia. The focus of this paper concerns two coal bumps that occurred in the Kellioka seam where both undermining and overmining had occurred. The purpose of the investigation is to determine the magnitude and distribution of vertical stress that initiated the bumps, to identify bump-prone areas in the unmined reserve, and to recommend pillar centers and mining layouts to avoid future bumps. The state of stress in three vertically adjacent seams was examined using the LAMODEL boundary element program. Large, detailed numerical models were constructed of both bump areas and of the remaining unmined reserve block. The results of the numerical analyses were compared with those obtained using analytical equations.

Jan 1, 2002

By Edward S. Custer

Recent investigations of mine roof falls have demonstrated that roof failures are generally associated with geologic conditions. The roof falls can be predicted by using the techniques of depositional modeling for the coal bed and roof rocks, and by lineament analysis. The ability to predict potential roof failure areas will allow the engineer and mine planner to develop a mine plan to avoid the roof failure areas and thus reduce overall mining costs. The ability to avoid roof failure areas also will permit maximum recovery of the coal resources.

Jan 1, 1981

By Kent D. Mctyer

Mining commenced at Tasman Mine in late 2006. The current method of mining is bord and pillar using continuous minerbolters and shuttle cars for first workings and secondary extraction using mobile roof supports. The two stage process was chosen to accommodate irregularly shaped coal deposits, allowing adjustments to be made to extraction ratios for better management of subsidence and to maximize the efficiency of the operation. Following the completion of the first three full/partial extraction panels, the mining method was changed due to variable caving. Another partial extraction method, referred to as the Duncan Method was adopted; it involves stripping the developed square pillars on four-sides on retreat to leave a load-bearing remnant coal pillar. The system of partial extraction has been successful in meeting safety, productivity, and subsidence targets.

Jan 1, 2011

By D. J. Reddish

This paper illustrates how numerical modelling has been utilised to predict water and gas pathways around active longwall panels using two case studies. This information has proved invaluable m the design of methane drainage schemes and for risk assessments undertaken at the mining planning stage. The modelling approach described has now been applied successfully to several situations in UK coalmines in order to optimise the position, length and orientation of methane drainage boreholes. The first case study describes the numerical modelling of the stress and shear plane development mund a longwall panel. The simulation was used to predict potential gas pathways through regions of low stress confinrment which are conducive to fluid flow. The conclusions from the modelling were utilised to allow an increase in the volumes of gas drainage and allow the efficient mining of the panel. A detailed discussion is provided on the model construction, determination of input paramters and optimisation of the borehole positions Details are provided on how the models allow a prediction of the fracture patterns, stress distributions and zones of reduced permeability around an active longwall panel. The second case study describes the numerical modelling of a fault adjacent to a face line drivage of a panel that had just started to be retreated. An inrush of water had occurred and a concern was whether further mining would lead to more extensive inrushes or whether the water inrush was associated with more local, limited capacity water bearing features. The role of a fault that was positioned close to the locality of the mine workings was examined. Fracture patterns stresses, strata permeability and water flows were predicted using mechanical and hydro-mechanical coupled models.

Jan 1, 2003

By C. W. Bollier

In recent years, Peabody Coal Company has enjoyed a great amount of success using roof trussing as a secondary support system. Since 1975, over 180,000 trusses have been installed in 12 different Peabody mines with varying geological conditions. Projections from Peabody, and throughout the mining industry, indicate a continuous growth in the trussing principle for roof control. Peabody's primary supplier has sold over 1,000,000 trusses to 50 different mines throughout the country. (1) Roof trusses provide an improved means of controlling difficult roof conditions which, in turn, improves worker safety and mine production. Since the original development of the truss, (2) the only major modification to the trussing procedure has been the addition of the resin point anchor system in the mid-70's. The resin point anchor was the catalyst needed to provide a reliable anchor and create acceptance of the roof truss by both management and labor. Peabody began using trusses in their mines in 1975. For the first few years, most of the truss effort was geared toward determining proper anchorage, spacing, and gathering historical data. In recent years, Peabody's activities have centered on the development of improving trussing procedures. Through monitoring and trussing activities, a number of areas of improvement have been found.

Jan 1, 1982

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By Lu Jiam Zhang

Coal and gas outburst is one of the serious natural disasters in the coal mines of China. Since 1950, more than 10,000 coal or gas outbursts have occurred in more than 200 underground coal mines of different types. The outburst prone coal mines are widely spread out. It occurs in different types of coal -ma and is very serious in some areas. Most outbursts occurred at the time of roadway driving in coal seam, serious outbursts occurred mainly when entering the coal seam during the cross-cut driving; of the outbursts, coal and gas outbursts We UP major proportion, while pressing out and pouring out ah account for a large proportion; outburst. occur under different operating conditions, but mostly occur during shotfiring. This paper introduces the prevention and control measures as practiced in China and illustrates the three types of outburst cla8sification. Both technology and management are equally important in outburst prevention and control. Measurement of the volume of drilling cuttings and the initial gas outflow rate fm- boreholes have proven to be effective. A special team and organization must be set up to deal with the problems.

Jan 1, 1987

By Graham Daws

State of the Art Room and Pillar mining techniques have been employed at two coal mines in the UK in the last two years. This paper describes the design of pillars and rockbolted support systems for Room and Pillar mining operations in these collieres. Within the last year, rock mass classification systems have been used in the design process of a room and pillar mining layout at one of these collieries. In particular, the roofbolt support system was detailed using these techniques and the support system was linked with operational aspects such as depth of cut. The depth of cut was initially estimated using rock mass classification systems and then verified by a stand up trial which was monitored remotely. The stand up time has a direct influence on the operational aspects of the mine and this is described. The design was verified by performance monitoring and the results are discussed. The importance of understanding the role of rockbolting is emphasised along with some examples of accurately determining in-situ bolt performance. The paper also recommends some modifications to rock mass classification systems when applied to underground coal mining operations.

Jan 1, 1998

By Paul L. Tyrna

The Fola Coal Co., LLC No 2 surface mine, located in Nicholas and Clay Counties, WV, exploits up to nine coal seams by contour, highwall, and mountain top removal mining methods. After encountering faults, areas of highly fractured coal, and subsidence failures. the mine requested a lineament analysis from the Mine Safety & Health Administration's (Pittsburgh Safety and Health Technology Center) Roof Control Division. The 31 km2 study area was viewed on a LANDSAT-5 band 4 (near infrared, 0.76-0.90 µm wavelength) satellite image with ERDAS Imagine 8.4 software. The software allows image examination under artificial sun azimuths and elevations, resulting in variable tonal characteristics. The study area image was viewed in 45° azimuthal increments from 000° to 315° at artificial sun angles of 10°, 30°, 50°, and 70°, yielding 32 separate images. The interpretation process developed by MSHA Roof Control personnel identified 16 northeast-striking and one northwest-striking lineament that intersected mine property. Faults and areas of roof instability corresponded well with lineaments identified in the study. Successful lineament identification prompted mine management to incorporate lineament analysis as a mine-planning tool for adjacent property, thereby identifying in advance areas that could adversely affect safety and production.

Jan 1, 2001

By Murali Gadde

U.S. coal mines? primary roof supports typically consist of passive resin bolts; however, the use of active bolt systems is increasing. Despite this widespread use, a comparative performance evaluation of these bolt systems has not been done under similar geologic conditions. The performances of three commonly used primary bolt systems were investigated: fully grouted passive rebar, fully grouted tension rebar (using two speed setting resin), and resin-assisted rebar with mechanical anchors. In order to investigate the performance of these bolts, strain gauged bolts of all three types were installed at three different coal mines as part of a larger research project funded by the National Institute for Occupational Safety and Health (NIOSH). This paper addresses the initial installation bolt loads measured at these mines. Analysis of the data showed much lower installed loads on active bolts than is traditionally assumed. It appears that the active load on bolts bleeds off relatively quickly under geologic and operational conditions similar to those at the studied mines. The data also showed that within a short time span after installation, the measured loads on active and passive bolts did not differ significantly. This paper compares the results from over 20 bolts of each bolt type that were all 1.8-m (6-ft) -long, 20-mm (0.804-in) nominal diameter Grade 75 rebar and discusses the relevance and shortcomings of the data and bolt performance.

Jan 1, 2011

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998