Search Documents

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

By Brian Clifford

Thoresby Colliery is in the process of recovering an old roadway that was flooded following the closure of an adjacent mine. The aim is to re-use the roadway as a gate road for a longwall retreat panel and it is therefore important to establish the condition of the existing rockbolt support during the recovery operation. Two NDT methods, ultrasonics and RMT's newly developed RF (Radio Frequency) system were used in combination to interrogate the rockbolts to determine their condition. This paper describes the condition of the rockbolt supports, the NDT methods used and the problems that had to be overcome to successfully apply the two methods.

Jan 1, 2002

By Tom Wynne

In order to shorten the time required and improve safety for a longwall face move, a 36-ft wide longwall recovery room was predriven. The room was supported with specialty bolts, trusses and concrete cribs. Rock mechanics instrumentation was implemented to evaluate the adequacy of the whole recovery system. This included instrumented roof bolts, entry convergence, load cells, and abutment stress in the surrounding pillars. This paper describes the methodology of support and instrumentation designs, and monitoring and evaluations. The results indicated that this method offers the safest and yet faster longwall recovery so far. But the rock mechanics monitoring also indicated some improvements are desirable in the truss system and concrete crib layout.

Jan 1, 1993

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By Robert C. Garson

The Mine Roof Simulator at the DOE'S Mining Equipment Test Facility is described. Its use in the research and development on the behavior and response of longwall roof supports to simulated mine environment is investigated. Advanced technology analysis methods such as finite element modeling, strain gage instrumentation, and photoelastic techniques are investigated for application in roof support design two case studies are presented of test data and results.

Jan 1, 1982

By T. P. Mucho

Mine roof failure due to excessive horizontal stress has been recognized as a major cause of hazardous roof conditions in some mines. Stress measurements gathered by the U.S. Bureau of Mines (USBM) at 24 different eastern mines show horizontal stress to be typically 2 to 3 times as great as vertical stress. The focus of current Bureau work is to develop detailed design parameters to assess and control the effects of horizontal stress. To facilitate the recognition of horizontal stress effects and to easily determine principal stress direction without resorting to cumbersome, expensive, and time consuming field measurements, the Bureau has developed a stress mapping methodology. Stress recognition and direction determination are required to successfully employ a number of control strategies such as mine layout, mining sequences, and support optimization to control the effects of horizontal stress, thereby increasing the safety of U.S. coal mines. This approach has been used in other major coal producing countries, most notably Australia and the UK, and has greatly enhanced the safety of their mines (1). This paper discusses horizontal stress, directional based control techniques, and provides guidelines for the use of the stress mapping technique. A case study of a mine where the technique has been used is also presented.

Jan 1, 1994

By Xianming Zhou

Mining economics is such that too conservative in safety will result in a considerable penalty in mining cost. However, initial planning and design of a mining project often must be done without complete information. The assurance of economical and safe mining is thus difficult. This study is focused on the improvement of the mine design associated with Zhaoyuan Gold Mine in P.R. China as more information becomes available. Attention is given to the selection of backfill structures. Based on a proposed practical finite element model, a design, which is believed to be not only reliable but also cost-effective, is recommended for further mining operations in this mine.

Jan 1, 1989

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Kanaan Hanna

The integrity factor approach was developed by the Bureau of nines to assess the stability of mine pillars and has been applied primarily to longwall chain pillars. Recently this approach was applied to a room-and-pillar mine in the Illinois Coal Basin. A special configuration of hydraulic borehole pressure cells was installed in a pillar to determine the in situ strength-and- stress relationship of the coal pillar and to verify the applicability of the integrity factor approach. Results indicate that the integrity factor approach is applicable to the assessment of pillar st6b:lity and nay bs a realistic and effective approach for room-and-pillar mine design.

Jan 1, 1988

By Yi You

A research has been conducted to study the long-term subsidence and its possible effects on surface structures In this research, the surface movements in areas when potential for developing long-term subsidence is high have been monitored over an extended period of time Long-term subsidence data have also been collected from other sources The avail- able data from this on-going research have been analyzed and the results is presented in this paper.

Jan 1, 1997

By T. L. Dobecki

As a means of demonstrating the effectiveness of reflection seismology in determining continuity of coal seams, three U. S. field projects are reviewed. The three projects involve coals of varied thickness (2-14m) and age (Pennsylvanian to Eocene) from three coal areas of the U. S. (Pennsylvania, Wyoming, and Washington). Each project also employed its own particular seismic technique, recording system, and seismic energy source although all are considered state-of-the-art, high resolution, digital seismic surveys. Project 1 (thin, Pennsylvania coal) sought detection of sand channels using dynamite and standard in-line (2-D) seismic technique. Project 2 (thick, Wyoming underground coal gasification) involved a gas-explosion (Dinoseis) source with areal (3-D) acquisition methods. Project 3 (thick, Washington underground coal gasification) employed a shotgun-type source and standard in- line methods. Data processing was handled by different contractors for each project. Each project was successful in accomplishing its own particular objective; however, data quality and interpretation seem to be more a function of thickness of the target seam, complexity of the overburden, and processing contractor than a seismic source, acquisition scheme (2-D versus 3-D), or recording instrumentation.

Jan 1, 1981

By William Bookshar

The development of increasingly more sophisticated and powerful retreat longwall equipment has led to ever wider and longer panels. To maximize gateroad development efficiency, provide for effective face recovery, andlor reduce ventilation pressures, entries are cut across longwall panels in advance of longwall retreat mining. These entries must be supported to prevent falls of immediate roof in advance of the face. Recently, cut through entries and predriven recovery room entries have been supported with various combinations of roof bolts and passive support. The cost and relative success of these support systems has varied considerably. Eighty-Four Mining Company, Fosroc, and Sub-Technical have developed and implemented an efficient, yielding, multiple component, cement crib to support longwall panel cut through entries and pre-driven recovery rooms. The cutable crib consists of an inexpensive flyash cement pillar poured in a bag, within a temporary metal form. The form is moved to a subsequent cutable crib location after the initial hardening of the flyash pillar. The remaining entry height between the mine roof and the top of the flyash cement pillar is filled with a specially designed bag filled with Fosroc's Tekset cement formulation. The diameter of the pillar and thickness of the Tekset bag are designed to accommodate the anticipated front abutment loading and entry convergence.

Jan 1, 1998

By Anil Mahyera

Under contract to the Bureau of Mines, a roofbolting machine has been developed which will: control torque on the bolthead to within 4 percent of a set point, control thrust to a low level (150 lbf), and implement a tightening method to minimize variability due to bolt tension decay of a group of bolts caused by differing anchor creep rates. This bolter was used to determine bolthead and thread friction factors, and to determine the effect of adding a hardened washer to the bolt assembly on the uniformity of bolt tension in the laboratory and field. Recommendations for torquing speed, bolt lubrication, use of hardened washers, and thrust level on the bolthead are made. The relationship of this system to Improved roof control is discussed, along with additional work that remains to be performed. Patent Notice Patents are pending which protect the hardware and methods of controlling tension decay as discussed in this paper.

Jan 1, 1981

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By Paul Hagan

A diverse range of rockbolt designs and resin anchors are available for use in underground mines. Despite their wide spread use, the factors that affect the performance a rockbolt is not fully understood. The laboratory-scale rockbolt test facility at the UNSW Mining Research Centre is being used to gain a better understanding of the behaviour of rockbolts leading to an improvement in ground support. A test program investigated the nature of load transfer between a fully encapsulated rockbolt and the surrounding rock mass. It was found that with all other factors held constant, there were differences in the behaviour of load transfer depending on the method of loading. The typical pull-out arrangement as used in most field test work resulted in a different load transfer function to that observed when the load on the rockbolt was induced through bed separation.

Jan 1, 2004

By Deren Zhu

Based on the results of field observation and physical model analyses, a computer simulation method, FEAEBP, has been developed for simulating the breakage of the main roof by considering it as a Kirchhoff plate on Winkler elastic foundation. By this method various parameters of rock property, different boundary conditions of the working face and the initiation, development and results of the breaking process of the main roof with different geometric dimensions can be effectively simulated. Since the main and immediate roofs, and the coal seams are treated as an integrated mechanical system, the interaction among them can be studied in detail.

Jan 1, 1988

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000